We need to re-initialise the stack pointers for undefined, IRQ
and abort mode handlers whenever we resume.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Create a temporary page table to startup secondary processors. This
page table must have a 1:1 virtual/physical mapping for the kernel
in addition to the standard mappings to ensure that the secondary
CPU can enable its MMU safely.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Without this some devices fail to work again after a suspend event.
Signed-off-by: Nicolas Pitre
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The GPIO base for Integrator/CP is different from the
Integrator/AP. This patch sets the correct value for
INTEGRATOR_GPIO_BASE.
Signed-off-by: Catalin Marinas
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The current red and blue colours on the Versatile CLCD are
reversed when the 5:6:5 mode is used. The patch sets the proper
bit in the SYS_CLCD register value.
Signed-off-by: Catalin Marinas
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Brownell
The ARM generic Kconfig filters out IDE options ... except for
an error prone ARMload of special cases.
This adds one general case to the systems that will offer IDE options:
kernels with PCMCIA support, which probably want to use IDE to access
CompactFlash cards. This might allow many (most?) of the other cases
to disappear, for systems that only see IDE hardware through CF cards.
Right now this one patch is used to gate access to CF cards, including
MicroDrives, for both omap_cf and at91_cf drivers.
Signed-off-by: David Brownell
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vincent Sanders
This fixes the "multiple definitions of cpufreq_get" build faliure on
the hackkit SA1100 platform.
Signed-off-by: Vincent Sanders
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vincent Sanders
This fixes the "multiple definitions of cpufreq_get" build faliure on
the Badge4 SA1100 platform.
Signed-off-by: Vincent Sanders
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Dave Neuer
This fixes the "multiple definitions of cpufreq_get" errors on
StrongARM-based iPAQs.
Signed-off-by: Dave Neuer
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Not that there might be many of them on the planet, but at least RMK
apparently has one.
Signed-off-by: Nicolas Pitre
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM copypage changes in 2.6.12-rc4-git1 removed the preempt locking
from the copypage functions which broke the XScale implementation.
This patch fixes the locking on XScale and removes the now unneeded
minicache code.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Checked-by: Richard Purdie
Patch from Deepak Saxena
The IXDP2800 bootloader does not disable IRQs before jumping into
the kernel and this is causing the Grand Unified KGDB to crash
the system when we do an early call to trap_init() and irq handlers
have not yet been registered. This patch disables IRQs before we
jump into the kernel.
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Todd Poynor
PXA27x sleep fixes:
* set additional sleep/wakeup registers for Mainstone boards.
* move CKEN=0 to pxa25x-specific code; that value is harmful on pxa27x.
* save/restore additional registers, including some found necessary for
C5 processors and/or newer blob versions.
* enable future support of additional sleep modes for PXA27x (eg,
standby, deep sleep).
* split off cpu-specific sleep processing between pxa27x and pxa25x into
separate files (partly in preparation for additional sleep modes).
Includes fixes from David Burrage.
Signed-off-by: Todd Poynor
Signed-off-by: Nicolas Pitre
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Albrecht Dre
Problem:
When a module requests a DMA channel via the function s3c2410_dma_request(), this function requests the appropriate irq under the name of the client module. When the client module is unloaded, it calls s3c2410_dma_free() which does not free the irq. Consequently, when e.g. running "cat /proc/interrupts", the irq owner points to freed memory, leading to a kernel oops.
File:
linux/arch/arm/mach-s3c2410/dma.c
Fix:
trivial, below
Signed-off-by: Albrecht Dre
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current vector entry system does not allow for SMP. In
order to work around this, we need to eliminate our reliance
on the fixed save areas, which breaks the way we enable
alignment traps. This patch changes the way we handle the
save areas such that we can have one per CPU.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
The current vector entry system does not allow for SMP. In
order to work around this, we need to eliminate our reliance
on the fixed save areas, which breaks the way we enable
alignment traps. This patch makes the alignment trap enable
code independent of the way we handle the save areas.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
By changing r9 -> r8 and r8 to 'tsk' (r9) we are able to remove
one instruction from the preempt path.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Patch from Ben Dooks
Fix the setting of hdiv when set to divide-by-2. Thanks to
Jeonghoon Yoon for pointing this out.
Change name of the NAND device to "s3c2440-nand" as it
is not similar enough to the "s3c2410-nand" device.
Signed-off-by: Ben Dooks
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
S3C2440 UPLL is the same as the S3C2410 UPLL, it is only the
MPLL which has an extra multiplication factor of 2 in the
multiplier.
Signed-off-by: Ben Dooks
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Not all ARMv6 processors implement the TLS register.
Signed-off-by: Nicolas Pitre
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the locking for copy_user_page() and clear_user_page() into
the implementations which require locking. For simple memcpy/
memset based implementations, the locking is extra overhead which
is not necessary, and prevents preemption occuring.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Add pmd_off() and pmd_off_k() to obtain the pmd pointer for a
virtual address, and use them throughout the mm initialisation.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Patch from Nicolas Pitre
This better express things, and should cover RMK's weird SMP toys.
Signed-off-by: Nicolas Pitre
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than using a long "depends on..." and "default y" lines for
these options, use select instead.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Various places in the ARM kernel implicitly assumed that kernel
stacks are always 8K due to hard coded constants. Replace these
constants with definitions.
Correct the allowable range of kernel stack pointer values within
the allocation. Arrange for the entire kernel stack to be zeroed,
not just the upper 4K if CONFIG_DEBUG_STACK_USAGE is set.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
A bunch of drivers use ISA DMA helpers or their equivalents for
platforms that have ISA with different DMA controller (a lot of ARM
boxen). Currently there is no way to put such dependency in Kconfig -
CONFIG_ISA is not it (e.g. it is not set on platforms that have no ISA
slots, but have on-board devices that pretend to be ISA ones).
New symbol added - ISA_DMA_API. Set when we have functional
enable_dma()/set_dma_mode()/etc. set of helpers. Next patches in the
series will add missing dependencies for drivers that need them.
I'm very carefully staying the hell out of the recurring flamefest on
what exactly CONFIG_ISA would mean in ideal world - added symbol has a
well-defined meaning and for now I really want to treat it as completely
independent from the mess around CONFIG_ISA.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Sascha Hauer
This patch adds the missing include files for the i.MX framebuffer
driver.
Signed-off-by: Sascha Hauer
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than duplicate the assembly for debug macros in the
decompressor head.S, use asm/arch/debug-macros.S instead.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Convert most of the current code that uses _NSIG directly to instead use
valid_signal(). This avoids gcc -W warnings and off-by-one errors.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The documentation on these values seems to be rather wrong.
These values have been determined by mere trial and error.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Patch from Lennert Buytenhek
The IXDP2800 is an evalution platform for the IXP2800 processor that
has two IXP2800s connected to the same PCI bus. This is problematic
as both CPUs will try to configure the PCI bus as they boot linux.
Contrary to on the other IXP2000 platforms, the boot loader on the
IXDP2800 doesn't configure the PCI bus properly, so we do want the
linux instance on one of the CPUs to do that.
Making one of the CPUs ignore the PCI bus (and thus act like a pure
PCI slave device) is not an option because there is a 82559 NIC on
the PCI bus for each of the CPUs.
The chosen solution is to have the master CPU configure the PCI bus
while the slave is kept in a quiescent state, and then to have the
slave CPU scan the PCI bus (without assigning resources) while the
master is kept in a quiescent state. After this ritual, the master
deletes the slave NIC from its PCI device list, the slave deletes
the master NIC from its device list, and (almost) all is well.
There's still one little problem: each of the CPUs has a 1G SDRAM
BAR, but the IXP2000 only has 512M of outbound PCI memory window.
We solve this by hand-assigning the master and slave SDRAM BARs to
a location outside each of the IXP's outbound PCI windows, and by
having the rest of the BARs autoconfigured in the outbound PCI
windows, in the range [e0000000..ffffffff], so that there is a 1:1
pci:phys mapping between them.
Even with this patch, a number of issues still remain -- just imagine
what happens if one of the CPUs is rebooted, by watchdog or by hand,
but the other one isn't. But those issues are not easily fixable
given the strange PCI layout of this board and the behavior of the
boot loader shipped with the platform.
Signed-off-by: Lennert Buytenhek
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
This patch is required for kernel XIP support on ARMv6 machines. It ensures that the access permission bits for kernel XIP section descriptors are APX=1 and AP[1:0]=01, which is Kernel read-only/User no access permissions. Prior to this change, kernel XIP section descriptor access permissions were set to Kernel no access/User no access on ARMv6 machines and the kernel would therefore hang upon entry to userspace when set_fs(USER_DS) was executed.
Signed-off-by: Steve Longerbeam
Signed-off-by: George G. Davis
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This patch entirely reworks the kernel assistance for NPTL on ARM.
In particular this provides an efficient way to retrieve the TLS
value and perform atomic operations without any instruction emulation
nor special system call. This even allows for pre ARMv6 binaries to
be forward compatible with SMP systems without any penalty.
The problematic and performance critical operations are performed
through segment of kernel provided user code reachable from user space
at a fixed address in kernel memory. Those fixed entry points are
within the vector page so we basically get it for free as no extra
memory page is required and nothing else may be mapped at that
location anyway.
This is different from (but doesn't preclude) a full blown VDSO
implementation, however a VDSO would prevent some assembly tricks with
constants that allows for efficient branching to those code segments.
And since those code segments only use a few cycles before returning to
user code, the overhead of a VDSO far call would add a significant
overhead to such minimalistic operations.
The ARM_NR_set_tls syscall also changed number. This is done for two
reasons:
1) this patch changes the way the TLS value was previously meant to be
retrieved, therefore we ensure whatever library using the old way
gets fixed (they only exist in private tree at the moment since the
NPTL work is still progressing).
2) the previous number was allocated in a range causing an undefined
instruction trap on kernels not supporting that syscall and it was
determined that allocating it in a range returning -ENOSYS would be
much nicer for libraries trying to determine if the feature is
present or not.
Signed-off-by: Nicolas Pitre
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
As noted in http://www.arm.com/linux/patch-2.6.9-arm1.gz, the "Faulty SWP instruction on 1136 doesn't set bit 11 in DFSR." So the v6_early_abort handler does not report the correct rd/wr direction for the SWP instruction which may result in SEGVS or hangs. In order to work around this problem, this patch merely updates the fix contained in the ARM Ltd. patch to use the macroised abort handler fixups.
Signed-off-by: George G. Davis
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Assigning the address zero to a PCI device BAR causes some part of the
PCI subsystem to believe that resource allocation for that BAR failed
due to resource conflicts, which will make attempts to enable the
device fail. Work around this by assigning I/O addresses starting
from 00010000.
While we're at it, make the PCI I/O resource end at 0001ffff, since we
only have 64k of outbound I/O window on the IXP2000, and we don't do
bank switching.
Signed-off-by: Lennert Buytenhek
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
On the IXDP2800, the bootloader does an awful job of configuring
the PCI bus, so we make linux reconfigure everything. Having a 1:1
pci:phys address mapping generally simplifies everything, so try to
allocate PCI addresses from the [e0000000..ffffffff] range, which is
the physical address range of the outbound PCI window on the IXP2000.
This does not affect any of the other IXP2000 platforms since they
all use their bootloader's PCI resource assignment.
Signed-off-by: Lennert Buytenhek
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Export ixp2000_pci_config_addr, to be used by the IXDP2800 platform
setup code to coordinate booting the master and slave NPU.
Signed-off-by: Lennert Buytenhek
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SVC_MODE reflects the MODE_SVC definition in asm/ptrace.h. Use
the asm/ptrace.h definition instead, and remove SVC_MODE.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Patch from Jeff Lackey
This patch updates arch/arm/mach-pxa/sleep.S to support
the PXA270 CPU. It works around Errata 39 & 50 from the
Intel(R) PXA27x Processor Family Specification Update.
Signed-off-by: Jeff Lackey
Signed-off-by: Russell King
ARM define FIRST_USER_ADDRESS as PAGE_SIZE (beyond the machine vectors when
they are mapped low), and use that definition in place of locally defined
MIN_MAP_ADDR.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert ARM bitop assembly to a macro. All bitops follow the same
format, so it's silly duplicating the code when only one or two
instructions are different.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Fix show_regs() to provide a backtrace. Provide a new __show_regs()
function which implements the common subset of show_regs() and die().
Add prototypes to asm-arm/system.h
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
The footbridge ISA RTC was being initialised before we had setup the
kernel timer. This caused a divide by zero error when the current
time of day is set. Resolve this by initialising the RTC after
the kernel timer has been initialised.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
)
From: Russell King <rmk+lkml@arm.linux.org.uk>
Oddly, max_low_pfn/max_pfn end up being the number of pages in the system,
rather than the maximum PFN on ARM. This doesn't seem to cause any problems,
so just add a note about it.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Russell King <rmk+lkml@arm.linux.org.uk>
For some reason, this help text was missed when the file was last audited
by the documentation referencing folk. Fix this incorrect documentation
reference.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
)
From: Russell King <rmk+lkml@arm.linux.org.uk>
ARM wasn't raising a SIGBUS with a siginfo structure. Fix
__do_user_fault() to allow us to use it for SIGBUS conditions, and arrange
for the sigbus path to use this.
We need to prevent the siginfo code being called if we do not have a user
space context to call it, so consolidate the "user_mode()" tests.
Thanks to Ian Campbell who spotted this oversight.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Russell King
Nicolas Pitre
Catalin Marinas
David Brownell
Vincent Sanders
Dave Neuer
Deepak Saxena
Todd Poynor
Albrecht Dre
Ben Dooks
Al Viro
Adrian Bunk
Sascha Hauer
Jesper Juhl
Stephen Rothwell
Lennert Buytenhek
George G. Davis
Jeff Lackey
Hugh Dickins
akpm@osdl.org
Linus Torvalds