Pull networking fixes from David Miller:
"Here are some bug fixes that have piled up during ksummit/linuxcon.
1) Fix endian problems in ibmveth, from Anton Blanchard.
2) IPV6 routing code does GFP_KERNEL allocation in atomic, fix from
Benjamin Block.
3) SCTP association fixes from Daniel Borkmann.
4) When multiple VLAN headers are present we have to make sure the
second and subsequent ones are pullable in the SKB otherwise we
blindly dereference garbage. From Jiri Benc.
5) The argument adjustment of the signature of hlist_add_after*()
introduced a regression in the batman-adv code, fix from Sven
Eckelmann.
6) Fix TX hang handling to avoid a panic in i40e, from Anjali Singhai
Jain.
7) PTP flag test is inverted in i40e driver, from Jesse Brandeburg.
8) ATM LEC driver needs to hold RTNL mutex over MTU changes, from
Chas Williams.
9) Truncate packets larger then the TPACKET_V3 format configured
buffers, otherwise we overwrite past the end of said buffers.
From Eric Dumazet.
10) Fix endianness bugs in qlcnic firmware handling, from Rajesh
Borundia and Shahed Shaikh.
11) CXGB4 sometimes doesn't get all of the TX completion events it
should resulting in SKBs getting stuck in the TX queue, from
Hariprasad Shenai.
12) When the FEC chip's PTP clock is disabled, you can't access the
register. Add necessary checks to avoid the resulting hang, from
Fugang Duan"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
drivers: isdn: eicon: xdi_msg.h: Fix typo in #ifndef
net: sctp: fix suboptimal edge-case on non-active active/retrans path selection
net: sctp: spare unnecessary comparison in sctp_trans_elect_best
net: ethernet: broadcom: bnx2x: Remove redundant #ifdef
ibmveth: Fix endian issues with rx_no_buffer statistic
net: xgene: fix possible NULL dereference in xgene_enet_free_desc_rings()
openvswitch: fix panic with multiple vlan headers
net: ipv6: fib: don't sleep inside atomic lock
net: fec: ptp: avoid register access when ipg clock is disabled
cxgb4: Free completed tx skbs promptly
cxgb4: Fix race condition in cleanup
sctp: not send SCTP_PEER_ADDR_CHANGE notifications with failed probe
bnx2x: Revert UNDI flushing mechanism
qlcnic: Fix endianess issue in firmware load from file operation
qlcnic: Fix endianess issue in FW dump template header
qlcnic: Fix flash access interface to application
MAINTAINERS: Add section for MRF24J40 IEEE 802.15.4 radio driver
macvlan: Allow setting multicast filter on all macvlan types
packet: handle too big packets for PACKET_V3
MAINTAINERS: add entry for ec_bhf driver
...
Commit da3c6647(I2C/ACPI: Clean up I2C ACPI code and Add CONFIG_I2C_ACPI
config) adds a new kernel config I2C_ACPI and make I2C core built in
when the config is selected. This is wrong because distributions
etc generally compile I2C as a module and the commit broken that.
This patch is to rename I2C_ACPI to ACPI_I2C_OPREGION. New config
only controls ACPI I2C operation region code and depends on I2C=y.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: removed unrelated change for Kconfig]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
A wildcard entry with the 32-bits OUI 0x600d8400 was added as part of
the BCM7xxx internal PHY driver, but that entry might match other PHYs
that are not covered by this driver, so let's just remove it.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
Pull input layer fixes from Dmitry Torokhov:
"Second round of updates for the input subsystem. Mostly small fixups
to the code merged in the first round (atmel_mxt_ts, wacom) but also a
smallish patch to xbox driver to support Xbox One controllers and a
patch to better handle Synaptics profile sensors found in Cr-48
Chromebooks that should not affect any other devices"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: edt-ft5x06 - remove superfluous assignment
Input: xpad - add support for Xbox One controllers
Input: atmel_mxt_ts - fix a few issues reported by Coverity
Input: atmel_mxt_ts - split config update a bit
Input: atmel_mxt_ts - simplify mxt_initialize a bit
Input: joystick - use get_cycles on ARMv8
Input: wacom - fix compiler warning if !CONFIG_PM
Input: cap1106 - allow changing key mapping from userspace
Input: synaptics - use firmware data for Cr-48
Input: synaptics - properly initialize slots for semi-MT
Input: MT - make slot cleanup callable outside mt_sync_frame()
Input: atmel_mxt_ts - mXT224 DMA quirk was fixed in firmware v2.0.AA
Pull EDAC updates from Mauro Carvalho Chehab.
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
sb_edac: add support for Haswell based systems
sb_edac: Fix mix tab/spaces alignments
edac: add DDR4 and RDDR4
sb_edac: remove bogus assumption on mc ordering
sb_edac: make minimal use of channel_mask
sb_edac: fix socket detection on Ivy Bridge controllers
sb_edac: update Kconfig description
sb_edac: search devices using product id
sb_edac: make RIR limit retrieval per model
sb_edac: make node id retrieval per model
sb_edac: make memory type detection per memory controller
- Fix for an ACPI-based device hotplug regression introduced in 3.14
that causes a kernel panic to trigger when memory hot-remove is
attempted with CONFIG_ACPI_HOTPLUG_MEMORY unset from Tang Chen.
- Fix for a cpufreq regression introduced in 3.16 that triggers a
"sleeping function called from invalid context" bug in
dev_pm_opp_init_cpufreq_table() from Stephen Boyd.
- ACPI battery driver fix for a warning message added in 3.16 that
prints silly stuff sometimes from Mariusz Ceier.
- Hibernation fix for safer handling of mismatches in the 820 memory
map between the configurations during image creation and during
the subsequent restore from Chun-Yi Lee.
- ACPI processor driver fix to handle CPU hotplug notifications
correctly during system suspend/resume from Lan Tianyu.
- Series of four cpuidle menu governor cleanups that also should
speed it up a bit from Mel Gorman.
- Fixes for the speedstep-smi, integrator, cpu0 and arm_big_little
cpufreq drivers from Hans Wennborg, Himangi Saraogi, Markus Pargmann
and Uwe Kleine-König.
- Version 3.0 of the analyze_suspend.py suspend profiling tool
from Todd E Brandt.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJT7UnNAAoJEILEb/54YlRxcxIP/ROFeak3+5tt3hkvZCevxpUh
AMPccgUoqsF2dognO3pcR4AgGP+meM6Qw0zBjPDNx6oo87hw7P1HlngfaRPHnWPh
iAkY2p1QhGAZW29vqxqBIdLVP9M+Nje0tvOX8/6QEsQgo2y6YCbJU0zITmvb8Tsk
183cXiz6xXDezt4sPeIVg2QVfngVFtOeNVgHDIhldQSF6zUQJP/3+BVutvaj3olt
2O3qpNfwJjFh9p6LWQ+CAalq3hJyNZ6ettLNCvudeq4kqRo49WAdjHaRW+qju/NR
dWybO29MfviczABVQ1ReqSnz0MJOqhZNxkEi5KqnYBb3fx8e2XffsBFzFzTp6BJi
bp4ALcFIu9r5ctWVxQhmgEC6uhYMIXZ681sH99HyIdzk2cNRgMxRj6u2aVe/Cczu
Bb489CRHmOrZyXrkmENg+LkOYBNoXcT+RepH9Ex8R+TNBlKLEBKMMgPrfbFeVKWB
Vm621tHNATJG8nJcs3zJulM2FQ0q8c2irw6WwhUxzbSOxmqSvO5zN3OgYt+c+gWk
MmA8IhUpQBLkqBx1FMi0lOOdIW3qKZJFrU39VQEjoP4P1nXgf373NPlfgzMvEvqM
qQ8srMKFUjYxH3g0ftWk5a2MwEjyHQpvZe0djsMCN7ZkFLwUe1ri/R9Ja2LLQcIZ
SyVkFbbO+moXTRMA1yA9
=kpiw
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are a couple of regression fixes, cpuidle menu governor
optimizations, fixes for ACPI proccessor and battery drivers,
hibernation fix to avoid problems related to the e820 memory map,
fixes for a few cpufreq drivers and a new version of the suspend
profiling tool analyze_suspend.py.
Specifics:
- Fix for an ACPI-based device hotplug regression introduced in 3.14
that causes a kernel panic to trigger when memory hot-remove is
attempted with CONFIG_ACPI_HOTPLUG_MEMORY unset from Tang Chen
- Fix for a cpufreq regression introduced in 3.16 that triggers a
"sleeping function called from invalid context" bug in
dev_pm_opp_init_cpufreq_table() from Stephen Boyd
- ACPI battery driver fix for a warning message added in 3.16 that
prints silly stuff sometimes from Mariusz Ceier
- Hibernation fix for safer handling of mismatches in the 820 memory
map between the configurations during image creation and during the
subsequent restore from Chun-Yi Lee
- ACPI processor driver fix to handle CPU hotplug notifications
correctly during system suspend/resume from Lan Tianyu
- Series of four cpuidle menu governor cleanups that also should
speed it up a bit from Mel Gorman
- Fixes for the speedstep-smi, integrator, cpu0 and arm_big_little
cpufreq drivers from Hans Wennborg, Himangi Saraogi, Markus
Pargmann and Uwe Kleine-König
- Version 3.0 of the analyze_suspend.py suspend profiling tool from
Todd E Brandt"
* tag 'pm+acpi-3.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / battery: Fix warning message in acpi_battery_get_state()
PM / tools: analyze_suspend.py: update to v3.0
cpufreq: arm_big_little: fix module license spec
cpufreq: speedstep-smi: fix decimal printf specifiers
ACPI / hotplug: Check scan handlers in acpi_scan_hot_remove()
cpufreq: OPP: Avoid sleeping while atomic
cpufreq: cpu0: Do not print error message when deferring
cpufreq: integrator: Use set_cpus_allowed_ptr
PM / hibernate: avoid unsafe pages in e820 reserved regions
ACPI / processor: Make acpi_cpu_soft_notify() process CPU FROZEN events
cpuidle: menu: Lookup CPU runqueues less
cpuidle: menu: Call nr_iowait_cpu less times
cpuidle: menu: Use ktime_to_us instead of reinventing the wheel
cpuidle: menu: Use shifts when calculating averages where possible
Pull networking fixes from David Miller:
"I'm sending this out, in particular, to get the iwlwifi fix
propagated:
1) Fix build due to missing include in i40e driver, from Lucas
Tanure.
2) Memory leak in openvswitch port allocation, from Chirstoph Jaeger.
3) Check DMA mapping errors in myri10ge, from Stanislaw Gruszka.
4) Fix various deadlock scenerios in sunvnet driver, from Sowmini
Varadhan.
5) Fix cxgb4i build failures with incompatible Kconfig settings of
the driver vs ipv6, from Anish Bhatt.
6) Fix generation of ACK packet timestamps in the presence of TSO
which will be split up, from Willem de Bruijn.
7) Don't enable sched scan in iwlwifi driver, it causes firmware
crashes in some revisions. From Emmanuel Grumbach.
8) Revert a macvlan simplification that causes crashes.
9) Handle RTT calculations properly in the presence of repair'd SKBs,
from Andrey Vagin.
10) SIT tunnel lookup uses wrong device index in compares, from
Shmulik Ladkani.
11) Handle MTU reductions in TCP properly for ipv4 mapped ipv6
sockets, from Neal Cardwell.
12) Add missing annotations in rhashtable code, from Thomas Graf.
13) Fix false interpretation of two RTOs as being from the same TCP
loss event in the FRTO code, from Neal Cardwell"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (42 commits)
netlink: Annotate RCU locking for seq_file walker
rhashtable: fix annotations for rht_for_each_entry_rcu()
rhashtable: unexport and make rht_obj() static
rhashtable: RCU annotations for next pointers
tcp: fix ssthresh and undo for consecutive short FRTO episodes
tcp: don't allow syn packets without timestamps to pass tcp_tw_recycle logic
tcp: fix tcp_release_cb() to dispatch via address family for mtu_reduced()
sit: Fix ipip6_tunnel_lookup device matching criteria
net: ethernet: ibm: ehea: Remove duplicate object from Makefile
net: xgene: Check negative return value of xgene_enet_get_ring_size()
tcp: don't use timestamp from repaired skb-s to calculate RTT (v2)
net: xilinx: Remove .owner field for driver
Revert "macvlan: simplify the structure port"
iwlwifi: mvm: disable scheduled scan to prevent firmware crash
xen-netback: remove loop waiting function
xen-netback: don't stop dealloc kthread too early
xen-netback: move NAPI add/remove calls
xen-netback: fix debugfs entry creation
xen-netback: fix debugfs write length check
net-timestamp: fix missing tcp fragmentation cases
...
Call rcu_deference_raw() directly from within rht_for_each_entry_rcu()
as list_for_each_entry_rcu() does.
Fixes the following sparse warnings:
net/netlink/af_netlink.c:2906:25: expected struct rhash_head const *__mptr
net/netlink/af_netlink.c:2906:25: got struct rhash_head [noderef] <asn:4>*<noident>
Fixes: e341694e3e ("netlink: Convert netlink_lookup() to use RCU protected hash table")
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to export rht_obj(), all inner to outer object translations
occur internally. It was intended to be used with rht_for_each() which
now primarily serves as the iterator for rhashtable_remove_pprev() to
effectively flush and free the full table.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly annotate next pointers as access is RCU protected in
the lookup path.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
- MR reregistration support
- MAD support for RMPP in userspace
- iSER and SRP initiator updates
- ocrdma hardware driver updates
- other fixes...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wOm0
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
"Main set of InfiniBand/RDMA updates for 3.17 merge window:
- MR reregistration support
- MAD support for RMPP in userspace
- iSER and SRP initiator updates
- ocrdma hardware driver updates
- other fixes..."
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (52 commits)
IB/srp: Fix return value check in srp_init_module()
RDMA/ocrdma: report asic-id in query device
RDMA/ocrdma: Update sli data structure for endianness
RDMA/ocrdma: Obtain SL from device structure
RDMA/uapi: Include socket.h in rdma_user_cm.h
IB/srpt: Handle GID change events
IB/mlx5: Use ARRAY_SIZE instead of sizeof/sizeof[0]
IB/mlx4: Use ARRAY_SIZE instead of sizeof/sizeof[0]
RDMA/amso1100: Check for integer overflow in c2_alloc_cq_buf()
IPoIB: Remove unnecessary test for NULL before debugfs_remove()
IB/mad: Add user space RMPP support
IB/mad: add new ioctl to ABI to support new registration options
IB/mad: Add dev_notice messages for various umad/mad registration failures
IB/mad: Update module to [pr|dev]_* style print messages
IB/ipoib: Avoid multicast join attempts with invalid P_key
IB/umad: Update module to [pr|dev]_* style print messages
IB/ipoib: Avoid flushing the workqueue from worker context
IB/ipoib: Use P_Key change event instead of P_Key polling mechanism
IB/ipath: Add P_Key change event support
mlx4_core: Add support for secure-host and SMP firewall
...
Pull more powerpc updates from Ben Herrenschmidt:
"Here are some more powerpc bits for 3.17, essentially fixes.
The biggest series, also aimed at -stable, is from Aneesh and is the
result of weeks and weeks of debugging to find out why the heck or THP
implementation was occasionally triggering multi-hit errors in our
level 1 TLB. It ended up being a combination of issues including
subtleties as to how we should invalidate those special 'MPSS' pages
we use to allow the use of 16M pages inside 4K/64K "base page size"
segments (you really have to love our MMU !)
Another interesting one in the "OMG" category is the series from
Michael adding memory barriers to spin_is_locked(). That's also the
result of many days of debugging to figure out why the semaphore code
would occasionally crash in ways that made no sense. It ended up
being some creative lock stacking that was defeated by the fact that
our locks allow a load inside the locked section to be re-ordered with
the load of the lock value itself (I'm still of two mind about whether
to kill that once and for all by putting a heavier barrier back into
our lock implementation...). The fixes come with a long explanation
in the cset comments, feel free to read it if you feel like having a
headache today"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (25 commits)
powerpc/thp: Add tracepoints to track hugepage invalidate
powerpc/mm: Use read barrier when creating real_pte
powerpc/thp: Use ACCESS_ONCE when loading pmdp
powerpc/thp: Invalidate with vpn in loop
powerpc/thp: Handle combo pages in invalidate
powerpc/thp: Invalidate old 64K based hash page mapping before insert of 4k pte
powerpc/thp: Don't recompute vsid and ssize in loop on invalidate
powerpc/thp: Add write barrier after updating the valid bit
powerpc: reorder per-cpu NUMA information's initialization
powerpc/perf/hv-24x7: Use kmem_cache_free
powerpc/pseries/hvcserver: Fix endian issue in hvcs_get_partner_info
powerpc: Hard disable interrupts in xmon
powerpc: remove duplicate definition of TEXASR_FS
powerpc/pseries: Avoid deadlock on removing ddw
powerpc/pseries: Failure on removing device node
powerpc/boot: Use correct zlib types for comparison
powerpc/powernv: Interface to register/unregister opal dump region
printk: Add function to return log buffer address and size
powerpc: Add POWER8 features to CPU_FTRS_POSSIBLE/ALWAYS
powerpc/ppc476: Disable BTAC
...
window:
Group changes to the device tree. In preparation for adding device tree
overlay support, OF_DYNAMIC is reworked so that a set of device tree
changes can be prepared and applied to the tree all at once. OF_RECONFIG
notifiers see the most significant change here so that users always get
a consistent view of the tree. Notifiers generation is moved from before
a change to after it, and notifiers for a group of changes are emitted
after the entire block of changes have been applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART devices
get this support automatically when uart_add_one_port() is called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then unloaded
again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory setup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT6M7XAAoJEMWQL496c2LNTTgP/2rXyrTTGZpK/qrLKHWKYHvr
XL7tcTkhA0OLU64E37fB+xtDXyBYnLsharuwUFSd1LlL1Wnc1cZN5ORRlMJbmjUR
Wvwl0A8/mkhGl4tzzKgJ4z4rMJXvlZfJRpnVoRB5FOn90LI7k/jsf5rIwF/6S90B
6D6II0r4RG9ku1m7g70cToxcIFCzp0V+eu2tym9GnhsyGKlunPT9iNiTpwfVhPAj
QUvMPKIQXReOv6xDU5q6E07839IMf7SdAvciBTHGnCDD7sGziHvnBIShj/2vTDAF
27sGRKrWUnnuxRUMOoIudiYyeHXIdt1WXp6FsS/ztVI37Ijh9YPShJwWGhQDppnp
4tcoSdefqw9IRUajAVWsB0RUW/tCL4a7tggWofylOA6itDi+HZnw6YafE1G1YzxF
q8OFo9uqLcmFQfHDJpk+sdtXoMZzOgrxlEscsGsQ8kd2Uoe8+chgR9EY1sqPkWVF
Zw0FJCTB6spBlsnXeboBGrnvpbPkacwhvesIFO0IANy4j4R55xlEeTcs1fe3ubUf
UhNyyFdnCAUA7e5CAabcAQYsdbEKG6v0Il3H6xts36c8lXCSFXVgNcw5mdCpFCcQ
DZ3/1FGSVzkYNXX8hlzIn1W0dqvwn4x0ZbnpXUJrGUBpSmjt9qkXx0XbdeFwartU
7X4tNGS1jfNYhOdP87jF
=8IFz
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree updates from Grant Likely:
"The branch contains the following device tree changes the v3.17 merge
window:
Group changes to the device tree. In preparation for adding device
tree overlay support, OF_DYNAMIC is reworked so that a set of device
tree changes can be prepared and applied to the tree all at once.
OF_RECONFIG notifiers see the most significant change here so that
users always get a consistent view of the tree. Notifiers generation
is moved from before a change to after it, and notifiers for a group
of changes are emitted after the entire block of changes have been
applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART
devices get this support automatically when uart_add_one_port() is
called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then
unloaded again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory
setup"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux: (21 commits)
of: Fixing OF Selftest build error
drivers: of: add automated assignment of reserved regions to client devices
of: Use proper types for checking memory overflow
of: typo fix in __of_prop_dup()
Adding selftest testdata dynamically into live tree
of: Add todo tasklist for Devicetree
of: Transactional DT support.
of: Reorder device tree changes and notifiers
of: Move dynamic node fixups out of powerpc and into common code
of: Make sure attached nodes don't carry along extra children
of: Make devicetree sysfs update functions consistent.
of: Create unlocked versions of node and property add/remove functions
OF: Utility helper functions for dynamic nodes
of: Move CONFIG_OF_DYNAMIC code into a separate file
of: rename of_aliases_mutex to just of_mutex
of/platform: Fix of_platform_device_destroy iteration of devices
of: Migrate of_find_node_by_name() users to for_each_node_by_name()
tty: Update hypervisor tty drivers to use core stdout parsing code.
arm/versatile: Add the uart as the stdout device.
of: Enable console on serial ports specified by /chosen/stdout-path
...
- Enable support for bus reset on device release
- Fixes for EEH support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJT64V6AAoJECObm247sIsimLkQAKL8sdGu2xwjujB/JFQrTXq0
9jN42aNhv50fVE9p2FKoqet/6VlQmRxLUvA9By94iMIKsUb3w0Rziti1FI3iyKtb
7lPzhCY9GWFnMD7Ero0nx+ljYrDiMlDdjeJ1ke25f1WZKMv524FJvA3cbiCvnAm0
3CRV0buq69deiiy5j1dbJdwYfPTJU7Jepqg8/OkjgJYokKRwqng9QfUgRbNwfL5d
FuVWaiGKvkxj4Sil0M3m4Ogf2yqqweX0am/rC3pGoO9woc9XFV560ABoEvXe3PI/
TPq3X63eqiBtu+t0qnYdi9jAfV62NMQEOwgb1z3IrIRoR9pwCOR2UFVQSr9X+rMp
EGrGUNkgU9cTzGeiSPmTII/ccYgsFpivy2UV+lNeDs4kraU++Q3QoJ2jwbzx8unF
nzyEfW8BizUenBZHsLvBDrlDddn5uEgao9ivdc9yBhjtOQshA8xMUKFG1PHzqtYg
Vis9/K2TKrZBcQTBD7nwCWWPLUg11N7stD6Ui0DEAEqJtGWxCNSqcKGTen1NvsOp
hpFdlySYORNvPQDMMBmjMc+YkngBwcwDaITE5FFMbyDJYymKA28MtkYaDVLZp5kZ
yYua3afxxDDaAzh7ikzUMpBlsSxbRpanAeTtEMQ0s2+ZfkzdvKztmTe9S26swQXG
p9hb4pIJNflk014lnNt1
=ADuE
-----END PGP SIGNATURE-----
Merge tag 'vfio-v3.17-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- enable support for bus reset on device release
- fixes for EEH support
* tag 'vfio-v3.17-rc1' of git://github.com/awilliam/linux-vfio:
drivers/vfio: Enable VFIO if EEH is not supported
drivers/vfio: Allow EEH to be built as module
drivers/vfio: Fix EEH build error
vfio-pci: Attempt bus/slot reset on release
vfio-pci: Use mutex around open, release, and remove
vfio-pci: Release devices with BusMaster disabled
- Forward compatibility for eMMC.
- Fix some blacklisted cards with broken secure discard.
MMC host:
- mmci: Add support for Qualcomm variant.
- mmci: Fix regression for arm_variant.
- sdhci: Various fixes and cleanups.
- sdhci: Improve external VDD regulator support.
- sdhci: Support for DDR50 1.8V mode for BayTrail.
- sdhci-st: Add driver for ST SDHCI controller.
- sh-mmcif: DMA fixes.
- omap_hsmmc: Add support for SDIO interrupts.
- sdhci-pci: Add support for Intel Quark X1000.
- dw_mmc: Update the reset sequence.
- s3cmci: port DMA code to dmaengine API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kGSY
-----END PGP SIGNATURE-----
Merge tag 'mmc-v3.17-1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"Me and Chris Ball decided to try out using my MMC tree as the primary
one, to simplify handling of patches.
This pull does thus contains all the MMC patches for 3.17 rc1, no pull
from Chris this time.
Details:
MMC core:
- forward compatibility for eMMC
- fix some blacklisted cards with broken secure discard
MMC host:
- mmci: Add support for Qualcomm variant
- mmci: Fix regression for arm_variant
- sdhci: Various fixes and cleanups
- sdhci: Improve external VDD regulator support
- sdhci: Support for DDR50 1.8V mode for BayTrail
- sdhci-st: Add driver for ST SDHCI controller
- sh-mmcif: DMA fixes
- omap_hsmmc: Add support for SDIO interrupts
- sdhci-pci: Add support for Intel Quark X1000
- dw_mmc: Update the reset sequence
- s3cmci: port DMA code to dmaengine API"
* tag 'mmc-v3.17-1' of git://git.linaro.org/people/ulf.hansson/mmc: (67 commits)
mmc: dw_mmc: modify the dt-binding for removing slot-node and supports-highspeed
mmc: dw_mmc: Slot quirk "disable-wp" is deprecated.
mmc: mmci: Reverse IRQ handling for the arm_variant
mmc: mmci: Move all CMD irq handling to mmci_cmd_irq()
mmc: mmci: Remove redundant check of status for DATA irq
mmc: dw_mmc: change to use recommended reset procedure
mmc: sdhci-pxav3: Use devm_* managed helpers
mmc: tmio: Configure DMA slave bus width
mmc: sh_mmcif: Configure DMA slave bus width
mmc: sh_mmcif: Fix DMA slave address configuration
mmc: sh_mmcif: Document DT bindings
mmc: sdhci-pci: remove PCI PM functions in suspend/resume callback
mmc: Do not advertise secure discard if it is blacklisted
mmc: sdhci-msm: Get COMPILE_TEST support
mmc: sdhci-msm: Remove unnecessary header file inclusion
mmc: sdhci-msm: Fix the binding example
mmc: sdhci: add DDR50 1.8V mode support for BayTrail eMMC Controller
mmc: sdhci: Preset value not supported in Baytrail eMMC
mmc: MMC_USDHI6ROL0 should depend on HAS_DMA
mmc: MMC_SH_MMCIF should depend on HAS_DMA
...
Pull block driver changes from Jens Axboe:
"Nothing out of the ordinary here, this pull request contains:
- A big round of fixes for bcache from Kent Overstreet, Slava Pestov,
and Surbhi Palande. No new features, just a lot of fixes.
- The usual round of drbd updates from Andreas Gruenbacher, Lars
Ellenberg, and Philipp Reisner.
- virtio_blk was converted to blk-mq back in 3.13, but now Ming Lei
has taken it one step further and added support for actually using
more than one queue.
- Addition of an explicit SG_FLAG_Q_AT_HEAD for block/bsg, to
compliment the the default behavior of adding to the tail of the
queue. From Douglas Gilbert"
* 'for-3.17/drivers' of git://git.kernel.dk/linux-block: (86 commits)
bcache: Drop unneeded blk_sync_queue() calls
bcache: add mutex lock for bch_is_open
bcache: Correct printing of btree_gc_max_duration_ms
bcache: try to set b->parent properly
bcache: fix memory corruption in init error path
bcache: fix crash with incomplete cache set
bcache: Fix more early shutdown bugs
bcache: fix use-after-free in btree_gc_coalesce()
bcache: Fix an infinite loop in journal replay
bcache: fix crash in bcache_btree_node_alloc_fail tracepoint
bcache: bcache_write tracepoint was crashing
bcache: fix typo in bch_bkey_equal_header
bcache: Allocate bounce buffers with GFP_NOWAIT
bcache: Make sure to pass GFP_WAIT to mempool_alloc()
bcache: fix uninterruptible sleep in writeback thread
bcache: wait for buckets when allocating new btree root
bcache: fix crash on shutdown in passthrough mode
bcache: fix lockdep warnings on shutdown
bcache allocator: send discards with correct size
bcache: Fix to remove the rcu_sched stalls.
...
Pull block core bits from Jens Axboe:
"Small round this time, after the massive blk-mq dump for 3.16. This
pull request contains:
- Fixes for max_sectors overflow in ioctls from Akinoby Mita.
- Partition off-by-one bug fix in aix partitions from Dan Carpenter.
- Various small partition cleanups from Fabian Frederick.
- Fix for the block integrity code sometimes returning the wrong
vector count from Gu Zheng.
- Cleanup an re-org of the blk-mq queue enter/exit percpu counters
from Tejun. Dependent on the percpu pull for 3.17 (which was in
the block tree too), that you have already pulled in.
- A blkcg oops fix, also from Tejun"
* 'for-3.17/core' of git://git.kernel.dk/linux-block:
partitions: aix.c: off by one bug
blkcg: don't call into policy draining if root_blkg is already gone
Revert "bio: modify __bio_add_page() to accept pages that don't start a new segment"
bio: modify __bio_add_page() to accept pages that don't start a new segment
block: fix SG_[GS]ET_RESERVED_SIZE ioctl when max_sectors is huge
block: fix BLKSECTGET ioctl when max_sectors is greater than USHRT_MAX
block/partitions/efi.c: kerneldoc fixing
block/partitions/msdos.c: code clean-up
block/partitions/amiga.c: replace nolevel printk by pr_err
block/partitions/aix.c: replace count*size kzalloc by kcalloc
bio-integrity: add "bip_max_vcnt" into struct bio_integrity_payload
blk-mq: use percpu_ref for mq usage count
blk-mq: collapse __blk_mq_drain_queue() into blk_mq_freeze_queue()
blk-mq: decouble blk-mq freezing from generic bypassing
block, blk-mq: draining can't be skipped even if bypass_depth was non-zero
blk-mq: fix a memory ordering bug in blk_mq_queue_enter()
Pull networking fixes from David Miller:
"Several networking final fixes and tidies for the merge window:
1) Changes during the merge window unintentionally took away the
ability to build bluetooth modular, fix from Geert Uytterhoeven.
2) Several phy_node reference count bug fixes from Uwe Kleine-König.
3) Fix ucc_geth build failures, also from Uwe Kleine-König.
4) Fix klog false positivies when netlink messages go to network
taps, by properly resetting the network header. Fix from Daniel
Borkmann.
5) Sizing estimate of VF netlink messages is too small, from Jiri
Benc.
6) New APM X-Gene SoC ethernet driver, from Iyappan Subramanian.
7) VLAN untagging is erroneously dependent upon whether the VLAN
module is loaded or not, but there are generic dependencies that
matter wrt what can be expected as the SKB enters the stack.
Make the basic untagging generic code, and do it unconditionally.
From Vlad Yasevich.
8) xen-netfront only has so many slots in it's transmit queue so
linearize packets that have too many frags. From Zoltan Kiss.
9) Fix suspend/resume PHY handling in bcmgenet driver, from Florian
Fainelli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (55 commits)
net: bcmgenet: correctly resume adapter from Wake-on-LAN
net: bcmgenet: update UMAC_CMD only when link is detected
net: bcmgenet: correctly suspend and resume PHY device
net: bcmgenet: request and enable main clock earlier
net: ethernet: myricom: myri10ge: myri10ge.c: Cleaning up missing null-terminate after strncpy call
xen-netfront: Fix handling packets on compound pages with skb_linearize
net: fec: Support phys probed from devicetree and fixed-link
smsc: replace WARN_ON() with WARN_ON_SMP()
xen-netback: Don't deschedule NAPI when carrier off
net: ethernet: qlogic: qlcnic: Remove duplicate object file from Makefile
wan: wanxl: Remove typedefs from struct names
m68k/atari: EtherNEC - ethernet support (ne)
net: ethernet: ti: cpmac.c: Cleaning up missing null-terminate after strncpy call
hdlc: Remove typedefs from struct names
airo_cs: Remove typedef local_info_t
atmel: Remove typedef atmel_priv_ioctl
com20020_cs: Remove typedef com20020_dev_t
ethernet: amd: Remove typedef local_info_t
net: Always untag vlan-tagged traffic on input.
drivers: net: Add APM X-Gene SoC ethernet driver support.
...
Highlights include:
- Stable fix for a bug in nfs3_list_one_acl()
- Speed up NFS path walks by supporting LOOKUP_RCU
- More read/write code cleanups
- pNFS fixes for layout return on close
- Fixes for the RCU handling in the rpcsec_gss code
- More NFS/RDMA fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KE07
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.17-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
- stable fix for a bug in nfs3_list_one_acl()
- speed up NFS path walks by supporting LOOKUP_RCU
- more read/write code cleanups
- pNFS fixes for layout return on close
- fixes for the RCU handling in the rpcsec_gss code
- more NFS/RDMA fixes"
* tag 'nfs-for-3.17-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (79 commits)
nfs: reject changes to resvport and sharecache during remount
NFS: Avoid infinite loop when RELEASE_LOCKOWNER getting expired error
SUNRPC: remove all refcounting of groupinfo from rpcauth_lookupcred
NFS: fix two problems in lookup_revalidate in RCU-walk
NFS: allow lockless access to access_cache
NFS: teach nfs_lookup_verify_inode to handle LOOKUP_RCU
NFS: teach nfs_neg_need_reval to understand LOOKUP_RCU
NFS: support RCU_WALK in nfs_permission()
sunrpc/auth: allow lockless (rcu) lookup of credential cache.
NFS: prepare for RCU-walk support but pushing tests later in code.
NFS: nfs4_lookup_revalidate: only evaluate parent if it will be used.
NFS: add checks for returned value of try_module_get()
nfs: clear_request_commit while holding i_lock
pnfs: add pnfs_put_lseg_async
pnfs: find swapped pages on pnfs commit lists too
nfs: fix comment and add warn_on for PG_INODE_REF
nfs: check wait_on_bit_lock err in page_group_lock
sunrpc: remove "ec" argument from encrypt_v2 operation
sunrpc: clean up sparse endianness warnings in gss_krb5_wrap.c
sunrpc: clean up sparse endianness warnings in gss_krb5_seal.c
...
Pull quota, reiserfs, UDF updates from Jan Kara:
"Scalability improvements for quota, a few reiserfs fixes, and couple
of misc cleanups (udf, ext2)"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
reiserfs: Fix use after free in journal teardown
reiserfs: fix corruption introduced by balance_leaf refactor
udf: avoid redundant memcpy when writing data in ICB
fs/udf: re-use hex_asc_upper_{hi,lo} macros
fs/quota: kernel-doc warning fixes
udf: use linux/uaccess.h
fs/ext2/super.c: Drop memory allocation cast
quota: remove dqptr_sem
quota: simplify remove_inode_dquot_ref()
quota: avoid unnecessary dqget()/dqput() calls
quota: protect Q_GETFMT by dqonoff_mutex
Pull Ceph updates from Sage Weil:
"There is a lot of refactoring and hardening of the libceph and rbd
code here from Ilya that fix various smaller bugs, and a few more
important fixes with clone overlap. The main fix is a critical change
to the request_fn handling to not sleep that was exposed by the recent
mutex changes (which will also go to the 3.16 stable series).
Yan Zheng has several fixes in here for CephFS fixing ACL handling,
time stamps, and request resends when the MDS restarts.
Finally, there are a few cleanups from Himangi Saraogi based on
Coccinelle"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (39 commits)
libceph: set last_piece in ceph_msg_data_pages_cursor_init() correctly
rbd: remove extra newlines from rbd_warn() messages
rbd: allocate img_request with GFP_NOIO instead GFP_ATOMIC
rbd: rework rbd_request_fn()
ceph: fix kick_requests()
ceph: fix append mode write
ceph: fix sizeof(struct tYpO *) typo
ceph: remove redundant memset(0)
rbd: take snap_id into account when reading in parent info
rbd: do not read in parent info before snap context
rbd: update mapping size only on refresh
rbd: harden rbd_dev_refresh() and callers a bit
rbd: split rbd_dev_spec_update() into two functions
rbd: remove unnecessary asserts in rbd_dev_image_probe()
rbd: introduce rbd_dev_header_info()
rbd: show the entire chain of parent images
ceph: replace comma with a semicolon
rbd: use rbd_segment_name_free() instead of kfree()
ceph: check zero length in ceph_sync_read()
ceph: reset r_resend_mds after receiving -ESTALE
...
Platforms like IBM Power Systems supports service processor
assisted dump. It provides interface to add memory region to
be captured when system is crashed.
During initialization/running we can add kernel memory region
to be collected.
Presently we don't have a way to get the log buffer base address
and size. This patch adds support to return log buffer address
and size.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
* pm-sleep:
PM / hibernate: avoid unsafe pages in e820 reserved regions
* pm-cpufreq:
cpufreq: arm_big_little: fix module license spec
cpufreq: speedstep-smi: fix decimal printf specifiers
cpufreq: OPP: Avoid sleeping while atomic
cpufreq: cpu0: Do not print error message when deferring
cpufreq: integrator: Use set_cpus_allowed_ptr
* pm-cpuidle:
cpuidle: menu: Lookup CPU runqueues less
cpuidle: menu: Call nr_iowait_cpu less times
cpuidle: menu: Use ktime_to_us instead of reinventing the wheel
cpuidle: menu: Use shifts when calculating averages where possible
Currently the functionality to untag traffic on input resides
as part of the vlan module and is build only when VLAN support
is enabled in the kernel. When VLAN is disabled, the function
vlan_untag() turns into a stub and doesn't really untag the
packets. This seems to create an interesting interaction
between VMs supporting checksum offloading and some network drivers.
There are some drivers that do not allow the user to change
tx-vlan-offload feature of the driver. These drivers also seem
to assume that any VLAN-tagged traffic they transmit will
have the vlan information in the vlan_tci and not in the vlan
header already in the skb. When transmitting skbs that already
have tagged data with partial checksum set, the checksum doesn't
appear to be updated correctly by the card thus resulting in a
failure to establish TCP connections.
The following is a packet trace taken on the receiver where a
sender is a VM with a VLAN configued. The host VM is running on
doest not have VLAN support and the outging interface on the
host is tg3:
10:12:43.503055 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27243,
offset 0, flags [DF], proto TCP (6), length 60)
10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x48d9), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294837885 ecr 0,nop,wscale 7], length 0
10:12:44.505556 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27244,
offset 0, flags [DF], proto TCP (6), length 60)
10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x44ee), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294838888 ecr 0,nop,wscale 7], length 0
This connection finally times out.
I've only access to the TG3 hardware in this configuration thus have
only tested this with TG3 driver. There are a lot of other drivers
that do not permit user changes to vlan acceleration features, and
I don't know if they all suffere from a similar issue.
The patch attempt to fix this another way. It moves the vlan header
stipping code out of the vlan module and always builds it into the
kernel network core. This way, even if vlan is not supported on
a virtualizatoin host, the virtual machines running on top of such
host will still work with VLANs enabled.
CC: Patrick McHardy <kaber@trash.net>
CC: Nithin Nayak Sujir <nsujir@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs updates from Al Viro:
"Stuff in here:
- acct.c fixes and general rework of mnt_pin mechanism. That allows
to go for delayed-mntput stuff, which will permit mntput() on deep
stack without worrying about stack overflows - fs shutdown will
happen on shallow stack. IOW, we can do Eric's umount-on-rmdir
series without introducing tons of stack overflows on new mntput()
call chains it introduces.
- Bruce's d_splice_alias() patches
- more Miklos' rename() stuff.
- a couple of regression fixes (stable fodder, in the end of branch)
and a fix for API idiocy in iov_iter.c.
There definitely will be another pile, maybe even two. I'd like to
get Eric's series in this time, but even if we miss it, it'll go right
in the beginning of for-next in the next cycle - the tricky part of
prereqs is in this pile"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (40 commits)
fix copy_tree() regression
__generic_file_write_iter(): fix handling of sync error after DIO
switch iov_iter_get_pages() to passing maximal number of pages
fs: mark __d_obtain_alias static
dcache: d_splice_alias should detect loops
exportfs: update Exporting documentation
dcache: d_find_alias needn't recheck IS_ROOT && DCACHE_DISCONNECTED
dcache: remove unused d_find_alias parameter
dcache: d_obtain_alias callers don't all want DISCONNECTED
dcache: d_splice_alias should ignore DCACHE_DISCONNECTED
dcache: d_splice_alias mustn't create directory aliases
dcache: close d_move race in d_splice_alias
dcache: move d_splice_alias
namei: trivial fix to vfs_rename_dir comment
VFS: allow ->d_manage() to declare -EISDIR in rcu_walk mode.
cifs: support RENAME_NOREPLACE
hostfs: support rename flags
shmem: support RENAME_EXCHANGE
shmem: support RENAME_NOREPLACE
btrfs: add RENAME_NOREPLACE
...
Pull slave-dma updates from Vinod Koul:
"Some notable changes are:
- new driver for AMBA AXI NBPF by Guennadi
- new driver for sun6i controller by Maxime
- pl330 drivers fixes from Lar's
- sh-dma updates and fixes from Laurent, Geert and Kuninori
- Documentation updates from Geert
- drivers fixes and updates spread over dw, edma, freescale, mpc512x
etc.."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (72 commits)
dmaengine: sun6i: depends on RESET_CONTROLLER
dma: at_hdmac: fix invalid remaining bytes detection
dmaengine: nbpfaxi: don't build this driver where it cannot be used
dmaengine: nbpf_error_get_channel() can be static
dma: pl08x: Use correct specifier for size_t values
dmaengine: Remove the context argument to the prep_dma_cyclic operation
dmaengine: nbpfaxi: convert to tasklet
dmaengine: nbpfaxi: fix a theoretical race
dmaengine: add a driver for AMBA AXI NBPF DMAC IP cores
dmaengine: add device tree binding documentation for the nbpfaxi driver
dmaengine: edma: Do not register second device when booted with DT
dmaengine: edma: Do not change the error code returned from edma_alloc_slot
dmaengine: rcar-dmac: Add device tree bindings documentation
dmaengine: shdma: Allocate cyclic sg list dynamically
dmaengine: shdma: Make channel filter ignore unrelated devices
dmaengine: sh: Rework Kconfig and Makefile
dmaengine: sun6i: Fix memory leaks
dmaengine: sun6i: Free the interrupt before killing the tasklet
dmaengine: sun6i: Remove switch statement from buswidth convertion routine
dmaengine: of: kconfig: select DMA_ENGINE when DMA_OF is selected
...
Pull thermal updates from Zhang Rui:
"Specifics:
- adds full support for 2 types of Thermal Controllers produced by
STMicroelectronics. One is a more traditional memory mapped
variant, the other is controlled solely by system configuration
registers. From Lee Jones.
- add TMU (Thermal Management Unit) support for Exynos3250 Soc.
From Chanwoo Choi.
- add critical and passive trip point support for int3403 thermal
driver. From Srinivas Pandruvada.
- a couple of small fixes/cleanups from Javi Merino, and Geert
Uytterhoeven"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: document struct thermal_zone_device and thermal_governor
thermal: cpu_cooling: fix typo highjack -> hijack
thermal: rcar: Document SoC-specific bindings
thermal: samsung: Add TMU support for Exynos3250 SoC
thermal: exynos: fix ordering in exynos_tmu_remove()
thermal: allow building dove_thermal with mvebu
thermal: sti: Add support for ST's Memory Mapped based Thermal controller
thermal: sti: Add support for ST's System Config Register based Thermal controller
thermal: sti: Introduce ST Thermal core code
thermal: sti: Supply Device Tree documentation
Thermal: int3403: Add CRT and PSV trip
arm and arm64 architectures. It required some minor updates to the generic
tracepoint system, so it had to wait for me to implement them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT5N6DAAoJEKQekfcNnQGuv60H/2NXDO/kUtvdF0L7ewaGbDaO
sjGOXMHDDgF4fQixPsIYNHdra0iGSPL59NBjIaLsESFsB8SUOVqXSclV0MSiZJQc
1PgTduE19p2kEMsqw6F4l8Ir8hPrUT8V8pQScR9lUkww3ANpyTB6Bbg1rZHcmTYA
yAq20q85rfQrAGwbvvhg40UYF8/su0FMUAbt/a180kVL8yeQI2liAkNOJTMCVq35
PpL7if4dlqAhKMqne71ae080PIPOH34q2lmZX3/SbpRvT2tSkS4dkoSFtCAD4pvx
c2TKNOxEDDWlinN/305PXH2yQ87MTIm44SBaTu/WPllUSQoO//EKI7+13tNS8Qc=
=/VeP
-----END PGP SIGNATURE-----
Merge tag 'trace-ipi-tracepoints' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull IPI tracepoints for ARM from Steven Rostedt:
"Nicolas Pitre added generic tracepoints for tracing IPIs and updated
the arm and arm64 architectures. It required some minor updates to
the generic tracepoint system, so it had to wait for me to implement
them"
* tag 'trace-ipi-tracepoints' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ARM64: add IPI tracepoints
ARM: add IPI tracepoints
tracepoint: add generic tracepoint definitions for IPI tracing
tracing: Do not do anything special with tracepoint_string when tracing is disabled
Pull namespace updates from Eric Biederman:
"This is a bunch of small changes built against 3.16-rc6. The most
significant change for users is the first patch which makes setns
drmatically faster by removing unneded rcu handling.
The next chunk of changes are so that "mount -o remount,.." will not
allow the user namespace root to drop flags on a mount set by the
system wide root. Aks this forces read-only mounts to stay read-only,
no-dev mounts to stay no-dev, no-suid mounts to stay no-suid, no-exec
mounts to stay no exec and it prevents unprivileged users from messing
with a mounts atime settings. I have included my test case as the
last patch in this series so people performing backports can verify
this change works correctly.
The next change fixes a bug in NFS that was discovered while auditing
nsproxy users for the first optimization. Today you can oops the
kernel by reading /proc/fs/nfsfs/{servers,volumes} if you are clever
with pid namespaces. I rebased and fixed the build of the
!CONFIG_NFS_FS case yesterday when a build bot caught my typo. Given
that no one to my knowledge bases anything on my tree fixing the typo
in place seems more responsible that requiring a typo-fix to be
backported as well.
The last change is a small semantic cleanup introducing
/proc/thread-self and pointing /proc/mounts and /proc/net at it. This
prevents several kinds of problemantic corner cases. It is a
user-visible change so it has a minute chance of causing regressions
so the change to /proc/mounts and /proc/net are individual one line
commits that can be trivially reverted. Unfortunately I lost and
could not find the email of the original reporter so he is not
credited. From at least one perspective this change to /proc/net is a
refgression fix to allow pthread /proc/net uses that were broken by
the introduction of the network namespace"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
proc: Point /proc/mounts at /proc/thread-self/mounts instead of /proc/self/mounts
proc: Point /proc/net at /proc/thread-self/net instead of /proc/self/net
proc: Implement /proc/thread-self to point at the directory of the current thread
proc: Have net show up under /proc/<tgid>/task/<tid>
NFS: Fix /proc/fs/nfsfs/servers and /proc/fs/nfsfs/volumes
mnt: Add tests for unprivileged remount cases that have found to be faulty
mnt: Change the default remount atime from relatime to the existing value
mnt: Correct permission checks in do_remount
mnt: Move the test for MNT_LOCK_READONLY from change_mount_flags into do_remount
mnt: Only change user settable mount flags in remount
namespaces: Use task_lock and not rcu to protect nsproxy
Pull nfsd updates from Bruce Fields:
"This includes a major rewrite of the NFSv4 state code, which has
always depended on a single mutex. As an example, open creates are no
longer serialized, fixing a performance regression on NFSv3->NFSv4
upgrades. Thanks to Jeff, Trond, and Benny, and to Christoph for
review.
Also some RDMA fixes from Chuck Lever and Steve Wise, and
miscellaneous fixes from Kinglong Mee and others"
* 'for-3.17' of git://linux-nfs.org/~bfields/linux: (167 commits)
svcrdma: remove rdma_create_qp() failure recovery logic
nfsd: add some comments to the nfsd4 object definitions
nfsd: remove the client_mutex and the nfs4_lock/unlock_state wrappers
nfsd: remove nfs4_lock_state: nfs4_state_shutdown_net
nfsd: remove nfs4_lock_state: nfs4_laundromat
nfsd: Remove nfs4_lock_state(): reclaim_complete()
nfsd: Remove nfs4_lock_state(): setclientid, setclientid_confirm, renew
nfsd: Remove nfs4_lock_state(): exchange_id, create/destroy_session()
nfsd: Remove nfs4_lock_state(): nfsd4_open and nfsd4_open_confirm
nfsd: Remove nfs4_lock_state(): nfsd4_delegreturn()
nfsd: Remove nfs4_lock_state(): nfsd4_open_downgrade + nfsd4_close
nfsd: Remove nfs4_lock_state(): nfsd4_lock/locku/lockt()
nfsd: Remove nfs4_lock_state(): nfsd4_release_lockowner
nfsd: Remove nfs4_lock_state(): nfsd4_test_stateid/nfsd4_free_stateid
nfsd: Remove nfs4_lock_state(): nfs4_preprocess_stateid_op()
nfsd: remove old fault injection infrastructure
nfsd: add more granular locking to *_delegations fault injectors
nfsd: add more granular locking to forget_openowners fault injector
nfsd: add more granular locking to forget_locks fault injector
nfsd: add a list_head arg to nfsd_foreach_client_lock
...
Pull arch signal handling cleanup from Richard Weinberger:
"This patch series moves all remaining archs to the get_signal(),
signal_setup_done() and sigsp() functions.
Currently these archs use open coded variants of the said functions.
Further, unused parameters get removed from get_signal_to_deliver(),
tracehook_signal_handler() and signal_delivered().
At the end of the day we save around 500 lines of code."
* 'signal-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/misc: (43 commits)
powerpc: Use sigsp()
openrisc: Use sigsp()
mn10300: Use sigsp()
mips: Use sigsp()
microblaze: Use sigsp()
metag: Use sigsp()
m68k: Use sigsp()
m32r: Use sigsp()
hexagon: Use sigsp()
frv: Use sigsp()
cris: Use sigsp()
c6x: Use sigsp()
blackfin: Use sigsp()
avr32: Use sigsp()
arm64: Use sigsp()
arc: Use sigsp()
sas_ss_flags: Remove nested ternary if
Rip out get_signal_to_deliver()
Clean up signal_delivered()
tracehook_signal_handler: Remove sig, info, ka and regs
...
Pull i2c updates from Wolfram Sang:
"Highlights:
- class based instantiation finally dropped for most embedded drivers
bringing boot up performance gains
- removed two drivers (one outdated, one a duplicate)
- ACPI has now operation region support (thanks to Lan Tianyu)
- the i2c-stub driver got overhauled and gained new features to
become more useful when writing i2c client drivers (thanks to
Guenter Roeck and Jean Delvare)
The rest is driver bugfixes, added bindings/ids, cleanups..."
* 'i2c/for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (43 commits)
i2c: mpc: delete unneeded test before of_node_put
i2c: rk3x: fix interrupt handling issue
i2c: imx: Fix format warning for dev_dbg
i2c: qup: disable clks and return instead of just returning error
i2c: exynos5: always enable HSI2C
i2c: designware: add new bindings
i2c: gpio: Drop dead code in i2c_gpio_remove
i2c: pca954x: put the mux to disconnected state after resume
i2c: st: Update i2c timings
drivers/i2c/busses: use correct type for dma_map/unmap
i2c: i2c-st: Use %pa to print 'resource_size_t' type
i2c: s3c2410: resume the I2C controller earlier
i2c: stub: Avoid an array overrun on I2C block transfers
i2c: i801: Add device ID for Intel Wildcat Point PCH
i2c: i801: Fix the alignment of the device table
i2c: stub: Add support for banked register ranges
i2c: stub: Remember the number of emulated chips
i2c: stub: Add support for SMBus block commands
i2c: efm32: correct namespacing of location property
i2c: exynos5: remove extra line and fix an assignment
...
AMD-compatible CFI driver:
- Support OTP programming for Micron M29EW family
- Increase buffer write timeout, according to detected flash parameter info
NAND
- Add helpers for retrieving ONFI timing modes
- GPMI: provide option to disable bad block marker swapping (required for
Ka-On electronics platforms)
SPI NOR
- EON EN25QH128 support
- Support new Flag Status Register (FSR) on a few Micron flash
Common
- New sysfs entries for bad block and ECC stats
And a few miscellaneous refactorings, cleanups, and driver improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Wkmz
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20140808' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"AMD-compatible CFI driver:
- Support OTP programming for Micron M29EW family
- Increase buffer write timeout, according to detected flash
parameter info
NAND
- Add helpers for retrieving ONFI timing modes
- GPMI: provide option to disable bad block marker swapping (required
for Ka-On electronics platforms)
SPI NOR
- EON EN25QH128 support
- Support new Flag Status Register (FSR) on a few Micron flash
Common
- New sysfs entries for bad block and ECC stats
And a few miscellaneous refactorings, cleanups, and driver
improvements"
* tag 'for-linus-20140808' of git://git.infradead.org/linux-mtd: (31 commits)
mtd: gpmi: make blockmark swapping optional
mtd: gpmi: remove line breaks from error messages and improve wording
mtd: gpmi: remove useless (void *) type casts and spaces between type casts and variables
mtd: atmel_nand: NFC: support multiple interrupt handling
mtd: atmel_nand: implement the nfc_device_ready() by checking the R/B bit
mtd: atmel_nand: add NFC status error check
mtd: atmel_nand: make ecc parameters same as definition
mtd: nand: add ONFI timing mode to nand_timings converter
mtd: nand: define struct nand_timings
mtd: cfi_cmdset_0002: fix do_write_buffer() timeout error
mtd: denali: use 8 bytes for READID command
mtd/ftl: fix the double free of the buffers allocated in build_maps()
mtd: phram: Fix whitespace issues
mtd: spi-nor: add support for EON EN25QH128
mtd: cfi_cmdset_0002: Add support for locking OTP memory
mtd: cfi_cmdset_0002: Add support for writing OTP memory
mtd: cfi_cmdset_0002: Invalidate cache after entering/exiting OTP memory
mtd: cfi_cmdset_0002: Add support for reading OTP
mtd: spi-nor: add support for flag status register on Micron chips
mtd: Account for BBT blocks when a partition is being allocated
...
* Much better HDMI infoframe support for OMAP
* Cirrus Logic CLPS711X framebuffer driver
* DT support for PL11x CLCD driver
* Various small fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gXX+
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- much better HDMI infoframe support for OMAP
- Cirrus Logic CLPS711X framebuffer driver
- DT support for PL11x CLCD driver
- various small fixes
* tag 'fbdev-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (35 commits)
OMAPDSS: DSI: fix depopulating dsi peripherals
video: hyperv: hyperv_fb: refresh the VM screen by force on VM panic
video: ARM CLCD: Fix DT-related build problems
drivers: video: fbdev: atmel_lcdfb.c: Add ability to inverted backlight PWM.
video: ARM CLCD: Add DT support
drm/omap: Add infoframe & dvi/hdmi mode support
OMAPDSS: HDMI: remove the unused code
OMAPDSS: HDMI5: add support to set infoframe & HDMI mode
OMAPDSS: HDMI4: add support to set infoframe & HDMI mode
OMAPDSS: HDMI: add infoframe and hdmi_dvi_mode fields
OMAPDSS: add hdmi ops to hdmi-connector and tpd12s015
OMAPDSS: add hdmi ops to hdmi_ops and omap_dss_driver
OMAPDSS: HDMI: remove custom avi infoframe
OMAPDSS: HDMI5: use common AVI infoframe support
OMAPDSS: HDMI4: use common AVI infoframe support
OMAPDSS: Kconfig: select HDMI
OMAPDSS: HDMI: fix name conflict
OMAPDSS: DISPC: clean up dispc_mgr_timings_ok
OMAPDSS: DISPC: reject interlace for lcd out
OMAPDSS: DISPC: fix debugfs reg dump
...
cycle, and this time we got a lot of action going on and
it will continue:
- The core GPIO library implementation has been split up in
three different files:
- gpiolib.c for the latest and greatest and shiny GPIO
library code using GPIO descriptors only
- gpiolib-legacy.c for the old integer number space API
that we are phasing out gradually
- gpiolib-sysfs.c for the sysfs interface that we are
not entirely happy with, but has to live on for
ABI compatibility
- Add a flags argument to *gpiod_get* functions, with some
backward-compatibility macros to ease transitions. We
should have had the flags there from the beginning it
seems, now we need to clean up the mess. There is a plan
on how to move forward here devised by Alexandre Courbot
and Mark Brown.
- Split off a special <linux/gpio/machine.h> header for the
board gpio table registration, as per example from the
regulator subsystem.
- Start to kill off the return value from gpiochip_remove()
by removing the __must_check attribute and removing all
checks inside the drivers/gpio directory. The rationale
is: well what were we supposed to do if there is an error
code? Not much: print an error message. And gpiolib already
does that. So make this function return void eventually.
- Some cleanups of hairy gpiolib code, make some functions
not to be used outside the library private and make sure
they are not exported, remove gpiod_lock/unlock_as_irq()
as the existing function is for driver-internal use and
fine as it is, delete gpio_ensure_requested() as it is
not meaningful anymore.
- Support the GPIOF_ACTIVE_LOW flag from gpio_request_one()
function calls, which is logical since this is already
supported when referencing GPIOs from e.g. device trees.
- Switch STMPE, intel-mid, lynxpoint and ACPI (!) to use
the gpiolib irqchip helpers cutting down on GPIO irqchip
boilerplate a bit more.
- New driver for the Zynq GPIO block.
- The usual incremental improvements around a bunch of
drivers.
- Janitorial syntactic and semantic cleanups by Jingoo Han,
and Rickard Strandqvist especially.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=e+d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO update from Linus Walleij:
"This is the bulk of GPIO changes for the v3.17 development cycle, and
this time we got a lot of action going on and it will continue:
- The core GPIO library implementation has been split up in three
different files:
- gpiolib.c for the latest and greatest and shiny GPIO library code
using GPIO descriptors only
- gpiolib-legacy.c for the old integer number space API that we are
phasing out gradually
- gpiolib-sysfs.c for the sysfs interface that we are not entirely
happy with, but has to live on for ABI compatibility
- Add a flags argument to *gpiod_get* functions, with some
backward-compatibility macros to ease transitions. We should have
had the flags there from the beginning it seems, now we need to
clean up the mess. There is a plan on how to move forward here
devised by Alexandre Courbot and Mark Brown
- Split off a special <linux/gpio/machine.h> header for the board
gpio table registration, as per example from the regulator
subsystem
- Start to kill off the return value from gpiochip_remove() by
removing the __must_check attribute and removing all checks inside
the drivers/gpio directory. The rationale is: well what were we
supposed to do if there is an error code? Not much: print an error
message. And gpiolib already does that. So make this function
return void eventually
- Some cleanups of hairy gpiolib code, make some functions not to be
used outside the library private and make sure they are not
exported, remove gpiod_lock/unlock_as_irq() as the existing
function is for driver-internal use and fine as it is, delete
gpio_ensure_requested() as it is not meaningful anymore
- Support the GPIOF_ACTIVE_LOW flag from gpio_request_one() function
calls, which is logical since this is already supported when
referencing GPIOs from e.g. device trees
- Switch STMPE, intel-mid, lynxpoint and ACPI (!) to use the gpiolib
irqchip helpers cutting down on GPIO irqchip boilerplate a bit more
- New driver for the Zynq GPIO block
- The usual incremental improvements around a bunch of drivers
- Janitorial syntactic and semantic cleanups by Jingoo Han, and
Rickard Strandqvist especially"
* tag 'gpio-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (37 commits)
MAINTAINERS: update GPIO include files
gpio: add missing includes in machine.h
gpio: add flags argument to gpiod_get*() functions
MAINTAINERS: Update Samsung pin control entry
gpio / ACPI: Move event handling registration to gpiolib irqchip helpers
gpio: lynxpoint: Convert to use gpiolib irqchip
gpio: split gpiod board registration into machine header
gpio: remove gpio_ensure_requested()
gpio: remove useless check in gpiolib_sysfs_init()
gpiolib: Export gpiochip_request_own_desc and gpiochip_free_own_desc
gpio: move gpio_ensure_requested() into legacy C file
gpio: remove gpiod_lock/unlock_as_irq()
gpio: make gpiochip_get_desc() gpiolib-private
gpio: simplify gpiochip_export()
gpio: remove export of private of_get_named_gpio_flags()
gpio: Add support for GPIOF_ACTIVE_LOW to gpio_request_one functions
gpio: zynq: Clear pending interrupt when enabling a IRQ
gpio: drop retval check enforcing from gpiochip_remove()
gpio: remove all usage of gpio_remove retval in driver/gpio
devicetree: Add Zynq GPIO devicetree bindings documentation
...
Pull input updates from Dmitry Torokhov:
- big update to Wacom driver by Benjamin Tissoires, converting it to
HID infrastructure and unifying USB and Bluetooth models
- large update to ALPS driver by Hans de Goede, which adds support for
newer touchpad models as well as cleans up and restructures the code
- more changes to Atmel MXT driver, including device tree support
- new driver for iPaq x3xxx touchscreen
- driver for serial Wacom tablets
- driver for Microchip's CAP1106
- assorted cleanups and improvements to existing drover and input core
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (93 commits)
Input: wacom - update the ABI doc according to latest changes
Input: wacom - only register once the MODULE_* macros
Input: HID - remove hid-wacom Bluetooth driver
Input: wacom - add copyright note and bump version to 2.0
Input: wacom - remove passing id for wacom_set_report
Input: wacom - check for bluetooth protocol while setting OLEDs
Input: wacom - handle Intuos 4 BT in wacom.ko
Input: wacom - handle Graphire BT tablets in wacom.ko
Input: wacom - prepare the driver to include BT devices
Input: hyperv-keyboard - register as a wakeup source
Input: imx_keypad - remove ifdef round PM methods
Input: jornada720_ts - get rid of space indentation and use tab
Input: jornada720_ts - switch to using managed resources
Input: alps - Rushmore and v7 resolution support
Input: mcs5000_ts - remove ifdef around power management methods
Input: mcs5000_ts - protect PM functions with CONFIG_PM_SLEEP
Input: ads7846 - release resources on failure for clean exit
Input: wacom - add support for 0x12C ISDv4 sensor
Input: atmel_mxt_ts - use deep sleep mode when stopped
ARM: dts: am437x-gp-evm: Update binding for touchscreen size
...
Merge more incoming from Andrew Morton:
"Two new syscalls:
memfd_create in "shm: add memfd_create() syscall"
kexec_file_load in "kexec: implementation of new syscall kexec_file_load"
And:
- Most (all?) of the rest of MM
- Lots of the usual misc bits
- fs/autofs4
- drivers/rtc
- fs/nilfs
- procfs
- fork.c, exec.c
- more in lib/
- rapidio
- Janitorial work in filesystems: fs/ufs, fs/reiserfs, fs/adfs,
fs/cramfs, fs/romfs, fs/qnx6.
- initrd/initramfs work
- "file sealing" and the memfd_create() syscall, in tmpfs
- add pci_zalloc_consistent, use it in lots of places
- MAINTAINERS maintenance
- kexec feature work"
* emailed patches from Andrew Morton <akpm@linux-foundation.org: (193 commits)
MAINTAINERS: update nomadik patterns
MAINTAINERS: update usb/gadget patterns
MAINTAINERS: update DMA BUFFER SHARING patterns
kexec: verify the signature of signed PE bzImage
kexec: support kexec/kdump on EFI systems
kexec: support for kexec on panic using new system call
kexec-bzImage64: support for loading bzImage using 64bit entry
kexec: load and relocate purgatory at kernel load time
purgatory: core purgatory functionality
purgatory/sha256: provide implementation of sha256 in purgaotory context
kexec: implementation of new syscall kexec_file_load
kexec: new syscall kexec_file_load() declaration
kexec: make kexec_segment user buffer pointer a union
resource: provide new functions to walk through resources
kexec: use common function for kimage_normal_alloc() and kimage_crash_alloc()
kexec: move segment verification code in a separate function
kexec: rename unusebale_pages to unusable_pages
kernel: build bin2c based on config option CONFIG_BUILD_BIN2C
bin2c: move bin2c in scripts/basic
shm: wait for pins to be released when sealing
...
This is the final piece of the puzzle of verifying kernel image signature
during kexec_file_load() syscall.
This patch calls into PE file routines to verify signature of bzImage. If
signature are valid, kexec_file_load() succeeds otherwise it fails.
Two new config options have been introduced. First one is
CONFIG_KEXEC_VERIFY_SIG. This option enforces that kernel has to be
validly signed otherwise kernel load will fail. If this option is not
set, no signature verification will be done. Only exception will be when
secureboot is enabled. In that case signature verification should be
automatically enforced when secureboot is enabled. But that will happen
when secureboot patches are merged.
Second config option is CONFIG_KEXEC_BZIMAGE_VERIFY_SIG. This option
enables signature verification support on bzImage. If this option is not
set and previous one is set, kernel image loading will fail because kernel
does not have support to verify signature of bzImage.
I tested these patches with both "pesign" and "sbsign" signed bzImages.
I used signing_key.priv key and signing_key.x509 cert for signing as
generated during kernel build process (if module signing is enabled).
Used following method to sign bzImage.
pesign
======
- Convert DER format cert to PEM format cert
openssl x509 -in signing_key.x509 -inform DER -out signing_key.x509.PEM -outform
PEM
- Generate a .p12 file from existing cert and private key file
openssl pkcs12 -export -out kernel-key.p12 -inkey signing_key.priv -in
signing_key.x509.PEM
- Import .p12 file into pesign db
pk12util -i /tmp/kernel-key.p12 -d /etc/pki/pesign
- Sign bzImage
pesign -i /boot/vmlinuz-3.16.0-rc3+ -o /boot/vmlinuz-3.16.0-rc3+.signed.pesign
-c "Glacier signing key - Magrathea" -s
sbsign
======
sbsign --key signing_key.priv --cert signing_key.x509.PEM --output
/boot/vmlinuz-3.16.0-rc3+.signed.sbsign /boot/vmlinuz-3.16.0-rc3+
Patch details:
Well all the hard work is done in previous patches. Now bzImage loader
has just call into that code and verify whether bzImage signature are
valid or not.
Also create two config options. First one is CONFIG_KEXEC_VERIFY_SIG.
This option enforces that kernel has to be validly signed otherwise kernel
load will fail. If this option is not set, no signature verification will
be done. Only exception will be when secureboot is enabled. In that case
signature verification should be automatically enforced when secureboot is
enabled. But that will happen when secureboot patches are merged.
Second config option is CONFIG_KEXEC_BZIMAGE_VERIFY_SIG. This option
enables signature verification support on bzImage. If this option is not
set and previous one is set, kernel image loading will fail because kernel
does not have support to verify signature of bzImage.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch does two things. It passes EFI run time mappings to second
kernel in bootparams efi_info. Second kernel parse this info and create
new mappings in second kernel. That means mappings in first and second
kernel will be same. This paves the way to enable EFI in kexec kernel.
This patch also prepares and passes EFI setup data through bootparams.
This contains bunch of information about various tables and their
addresses.
These information gathering and passing has been written along the lines
of what current kexec-tools is doing to make kexec work with UEFI.
[akpm@linux-foundation.org: s/get_efi/efi_get/g, per Matt]
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is loader specific code which can load bzImage and set it up for
64bit entry. This does not take care of 32bit entry or real mode entry.
32bit mode entry can be implemented if somebody needs it.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Load purgatory code in RAM and relocate it based on the location.
Relocation code has been inspired by module relocation code and purgatory
relocation code in kexec-tools.
Also compute the checksums of loaded kexec segments and store them in
purgatory.
Arch independent code provides this functionality so that arch dependent
bootloaders can make use of it.
Helper functions are provided to get/set symbol values in purgatory which
are used by bootloaders later to set things like stack and entry point of
second kernel etc.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previous patch provided the interface definition and this patch prvides
implementation of new syscall.
Previously segment list was prepared in user space. Now user space just
passes kernel fd, initrd fd and command line and kernel will create a
segment list internally.
This patch contains generic part of the code. Actual segment preparation
and loading is done by arch and image specific loader. Which comes in
next patch.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the new syscall kexec_file_load() declaration/interface. I have
reserved the syscall number only for x86_64 so far. Other architectures
(including i386) can reserve syscall number when they enable the support
for this new syscall.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
So far kexec_segment->buf was always a user space pointer as user space
passed the array of kexec_segment structures and kernel copied it.
But with new system call, list of kexec segments will be prepared by
kernel and kexec_segment->buf will point to a kernel memory.
So while I was adding code where I made assumption that ->buf is pointing
to kernel memory, sparse started giving warning.
Make ->buf a union. And where a user space pointer is expected, access it
using ->buf and where a kernel space pointer is expected, access it using
->kbuf. That takes care of sparse warnings.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have added two more functions to walk through resources.
Currently walk_system_ram_range() deals with pfn and /proc/iomem can
contain partial pages. By dealing in pfn, callback function loses the
info that last page of a memory range is a partial page and not the full
page. So I implemented walk_system_ram_res() which returns u64 values to
callback functions and now it properly return start and end address.
walk_system_ram_range() uses find_next_system_ram() to find the next ram
resource. This in turn only travels through siblings of top level child
and does not travers through all the nodes of the resoruce tree. I also
need another function where I can walk through all the resources, for
example figure out where "GART" aperture is. Figure out where ACPI memory
is.
So I wrote another function walk_iomem_res() which walks through all
/proc/iomem resources and returns matches as asked by caller. Caller can
specify "name" of resource, start and end and flags.
Got rid of find_next_system_ram_res() and instead implemented more generic
find_next_iomem_res() which can be used to traverse top level children
only based on an argument.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds
Lan Tianyu
Florian Fainelli
Thomas Graf
Roland Dreier
Vasant Hegde
Rafael J. Wysocki
Vlad Yasevich
Grant Likely
Jaehoon Chung
Vivek Goyal