Граф коммитов

5 Коммитов

Автор SHA1 Сообщение Дата
Lennert Buytenhek e84665c9cb dsa: add switch chip cascading support
The initial version of the DSA driver only supported a single switch
chip per network interface, while DSA-capable switch chips can be
interconnected to form a tree of switch chips.  This patch adds support
for multiple switch chips on a network interface.

An example topology for a 16-port device with an embedded CPU is as
follows:

	+-----+          +--------+       +--------+
	|     |eth0    10| switch |9    10| switch |
	| CPU +----------+        +-------+        |
	|     |          | chip 0 |       | chip 1 |
	+-----+          +---++---+       +---++---+
	                     ||               ||
	                     ||               ||
	                     ||1000baseT      ||1000baseT
	                     ||ports 1-8      ||ports 9-16

This requires a couple of interdependent changes in the DSA layer:

- The dsa platform driver data needs to be extended: there is still
  only one netdevice per DSA driver instance (eth0 in the example
  above), but each of the switch chips in the tree needs its own
  mii_bus device pointer, MII management bus address, and port name
  array. (include/net/dsa.h)  The existing in-tree dsa users need
  some small changes to deal with this. (arch/arm)

- The DSA and Ethertype DSA tagging modules need to be extended to
  use the DSA device ID field on receive and demultiplex the packet
  accordingly, and fill in the DSA device ID field on transmit
  according to which switch chip the packet is heading to.
  (net/dsa/tag_{dsa,edsa}.c)

- The concept of "CPU port", which is the switch chip port that the
  CPU is connected to (port 10 on switch chip 0 in the example), needs
  to be extended with the concept of "upstream port", which is the
  port on the switch chip that will bring us one hop closer to the CPU
  (port 10 for both switch chips in the example above).

- The dsa platform data needs to specify which ports on which switch
  chips are links to other switch chips, so that we can enable DSA
  tagging mode on them.  (For inter-switch links, we always use
  non-EtherType DSA tagging, since it has lower overhead.  The CPU
  link uses dsa or edsa tagging depending on what the 'root' switch
  chip supports.)  This is done by specifying "dsa" for the given
  port in the port array.

- The dsa platform data needs to be extended with information on via
  which port to reach any given switch chip from any given switch chip.
  This info is specified via the per-switch chip data struct ->rtable[]
  array, which gives the nexthop ports for each of the other switches
  in the tree.

For the example topology above, the dsa platform data would look
something like this:

	static struct dsa_chip_data sw[2] = {
		{
			.mii_bus	= &foo,
			.sw_addr	= 1,
			.port_names[0]	= "p1",
			.port_names[1]	= "p2",
			.port_names[2]	= "p3",
			.port_names[3]	= "p4",
			.port_names[4]	= "p5",
			.port_names[5]	= "p6",
			.port_names[6]	= "p7",
			.port_names[7]	= "p8",
			.port_names[9]	= "dsa",
			.port_names[10]	= "cpu",
			.rtable		= (s8 []){ -1, 9, },
		}, {
			.mii_bus	= &foo,
			.sw_addr	= 2,
			.port_names[0]	= "p9",
			.port_names[1]	= "p10",
			.port_names[2]	= "p11",
			.port_names[3]	= "p12",
			.port_names[4]	= "p13",
			.port_names[5]	= "p14",
			.port_names[6]	= "p15",
			.port_names[7]	= "p16",
			.port_names[10]	= "dsa",
			.rtable		= (s8 []){ 10, -1, },
		},
	},

	static struct dsa_platform_data pd = {
		.netdev		= &foo,
		.nr_switches	= 2,
		.sw		= sw,
	};

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 19:06:54 -07:00
Lennert Buytenhek 076d3e10a5 dsa: add support for the Marvell 88E6095/6095F switch chips
Add support for the Marvell 88E6095/6095F switch chips.  These
chips are similar to the 88e6131, so we can add the support to
mv88e6131.c easily.

Thanks to Gary Thomas <gary@mlbassoc.com> and Jesper Dangaard
Brouer <hawk@diku.dk> for testing various patches.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-21 19:06:54 -07:00
Harvey Harrison 09640e6365 net: replace uses of __constant_{endian}
Base versions handle constant folding now.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-01 00:45:17 -08:00
Roel Kluin 5eaa65b240 net: Make static
Sparse asked whether these could be static.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10 15:18:31 -08:00
Lennert Buytenhek 2e5f032095 dsa: add support for the Marvell 88E6131 switch chip
Add support for the Marvell 88E6131 switch chip.  This chip only
supports the original (ethertype-less) DSA tagging format.

On the 88E6131, there is a PHY Polling Unit (PPU) which has exclusive
access to each of the PHYs's MII management registers.  If we want to
talk to the PHYs from software, we have to disable the PPU and wait
for it to complete its current transaction before we can do so, and we
need to re-enable the PPU afterwards to make sure that the switch will
notice changes in link state and speed on the individual ports as they
occur.

Since disabling the PPU is rather slow, and since MII management
accesses are typically done in bursts, this patch keeps the PPU disabled
for 10ms after a software access completes.  This makes handling the
PPU slightly more complex, but speeds up something like running ethtool
on one of the switch slave interfaces from ~300ms to ~30ms on typical
hardware.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-08 17:24:09 -07:00