Граф коммитов

59 Коммитов

Автор SHA1 Сообщение Дата
Roberto Sassu bcfff8384f tpm: dynamically allocate the allocated_banks array
This patch renames active_banks (member of tpm_chip) to allocated_banks,
stores the number of allocated PCR banks in nr_allocated_banks (new member
of tpm_chip), and replaces the static array with a pointer to a dynamically
allocated array.

tpm2_get_pcr_allocation() determines if a PCR bank is allocated by checking
the mask in the TPML_PCR_SELECTION structure returned by the TPM for
TPM2_Get_Capability(). If a bank is not allocated, the TPM returns that
bank in TPML_PCR_SELECTION, with all bits in the mask set to zero. In this
case, the bank is not included in chip->allocated_banks, to avoid that TPM
driver users unnecessarily calculate a digest for that bank.

One PCR bank with algorithm set to SHA1 is always allocated for TPM 1.x.

As a consequence of the introduction of nr_allocated_banks,
tpm_pcr_extend() does not check anymore if the algorithm stored in tpm_chip
is equal to zero.

Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2019-02-13 09:48:50 +02:00
Jarkko Sakkinen 47a6c28b68 tpm: remove @flags from tpm_transmit()
Remove @flags from tpm_transmit() API. It is no longer used for
anything.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
2019-02-13 09:48:46 +02:00
Jarkko Sakkinen 2f257402ee tpm: remove TPM_TRANSMIT_UNLOCKED flag
Added locking as part of tpm_try_get_ops() and tpm_put_ops() as they are
anyway used in most of the call sites except in tpmrm_release() where we
take the locks manually.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
2019-02-13 09:48:28 +02:00
Jarkko Sakkinen 5faafbab77 tpm: remove @space from tpm_transmit()
Remove @space from tpm_transmit() API` in order to completely remove the
bound between low-level transmission functionality and TPM spaces. The
only real dependency existing is the amount of data saved before trying
to send a command to the TPM.

It doesn't really matter if we save always a bit more than needed so
this commit changes the amount saved always to be the size of the TPM
header and three handles.

Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
2019-02-13 09:48:12 +02:00
Jarkko Sakkinen b34b77a99b tpm: declare struct tpm_header
Declare struct tpm_header that replaces struct tpm_input_header and
struct tpm_output_header.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
2019-02-13 09:47:37 +02:00
Jarkko Sakkinen 412eb58558 tpm: use tpm_buf in tpm_transmit_cmd() as the IO parameter
Since we pass an initialized struct tpm_buf instance in every call site
now, it is cleaner to pass that directly to the tpm_transmit_cmd() as
the TPM command/response buffer.

Fine-tune a little bit tpm_transmit() and tpm_transmit_cmd() comments
while doing this.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Alexander Steffen <Alexander.Steffen@infineon.com>
2019-02-13 09:47:01 +02:00
Tomas Winkler 5122b5f0a8 tpm: fix kdoc for tpm2_flush_context_cmd()
kdoc for tpm2_flush_context_cmd() was off.

Fixes: 9aa36b399a ("tpm: export tpm2_flush_context_cmd")'
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-11-13 13:46:32 +02:00
Tomas Winkler 95adc6b410 tpm: use u32 instead of int for PCR index
The TPM specs defines PCR index as a positive number, and there is
no reason to use a signed number. It is also a possible security
issue as currently no functions check for a negative index,
which may become a large number when converted to u32.

Adjust the API to use u32 instead of int in all PCR related
functions.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-11-13 13:46:31 +02:00
Tomas Winkler 9db7fe187c tpm: factor out tpm_startup function
TPM manual startup is used only from within TPM 1.x or TPM 2.x
code, hence remove tpm_startup() function from tpm-interface.c
and add two static functions implementations tpm1_startup()
and tpm2_startup() into to tpm1-cmd.c and tpm2-cmd.c respectively.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-11-13 13:46:30 +02:00
Tomas Winkler 70a3199a71 tpm: factor out tpm_get_timeouts()
Factor out tpm_get_timeouts() into tpm2_get_timeouts()
and tpm1_get_timeouts()

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-11-13 13:46:30 +02:00
Tomas Winkler d856c00f7d tpm: add tpm_calc_ordinal_duration() wrapper
Add convenient wrapper for ordinal duration computation
to remove boiler plate if else statement over TPM2.

if (chip->flags & TPM_CHIP_FLAG_TPM2)
	tpm2_calc_ordinal_duration(chip, ordinal);
else
	tpm1_calc_ordinal_duration(chip, ordinal);

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-11-13 13:46:30 +02:00
Tomas Winkler 899102bc45 tpm2: add new tpm2 commands according to TCG 1.36
1. TPM2_CC_LAST has moved from 182 to 193
2. Convert tpm2_ordinal_duration from an array into a switch statement,
   as there are not so many commands that require special duration
   relative to a number of commands, the switch statement function
   is called tpm2_ordinal_duration_index().
3. Fix kdoc comments for tpm2_calc_ordinal_duration().

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-11-13 13:46:29 +02:00
Jarkko Sakkinen 84b59f6487 tpm: fix response size validation in tpm_get_random()
When checking whether the response is large enough to be able to contain
the received random bytes in tpm_get_random() and tpm2_get_random(),
they fail to take account the header size, which should be added to the
minimum size. This commit fixes this issue.

Cc: stable@vger.kernel.org
Fixes: c659af78eb ("tpm: Check size of response before accessing data")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-10-05 13:47:33 +03:00
Jarkko Sakkinen ce63c05b66 tpm: migrate tpm2_get_random() to use struct tpm_buf
In order to make struct tpm_buf the first class object for constructing
TPM commands, migrate tpm2_get_random() to use it. In addition, removed
remaining references to struct tpm2_cmd. All of them use it to acquire
the length of the response, which can be achieved by using
tpm_buf_length().

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Nayna Jain<nayna@linux.vnet.ibm.com>
2018-07-28 17:03:11 +03:00
Jarkko Sakkinen 2ab3241161 tpm: migrate tpm2_get_tpm_pt() to use struct tpm_buf
In order to make struct tpm_buf the first class object for constructing TPM
commands, migrate tpm2_get_tpm_pt() to use it.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Tested-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
2018-07-28 17:03:11 +03:00
Jarkko Sakkinen 94e266ba1f tpm: migrate tpm2_probe() to use struct tpm_buf
In order to make struct tpm_buf the first class object for constructing TPM
commands, migrate tpm2_probe() to use it.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Jay Freyensee <why2jjj.linux@gmail.com>
Reviewed-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Tested-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
2018-07-28 17:03:11 +03:00
Jarkko Sakkinen cc26c6ef58 tpm: migrate tpm2_shutdown() to use struct tpm_buf
In order to make struct tpm_buf the first class object for constructing TPM
commands, migrated tpm2_shutdown() to use it.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Tested-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
2018-07-28 17:03:11 +03:00
Kees Cook a86854d0c5 treewide: devm_kzalloc() -> devm_kcalloc()
The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc().
This patch replaces cases of:

        devm_kzalloc(handle, a * b, gfp)

with:
        devm_kcalloc(handle, a * b, gfp)

as well as handling cases of:

        devm_kzalloc(handle, a * b * c, gfp)

with:

        devm_kzalloc(handle, array3_size(a, b, c), gfp)

as it's slightly less ugly than:

        devm_kcalloc(handle, array_size(a, b), c, gfp)

This does, however, attempt to ignore constant size factors like:

        devm_kzalloc(handle, 4 * 1024, gfp)

though any constants defined via macros get caught up in the conversion.

Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.

Some manual whitespace fixes were needed in this patch, as Coccinelle
really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...".

The Coccinelle script used for this was:

// Fix redundant parens around sizeof().
@@
expression HANDLE;
type TYPE;
expression THING, E;
@@

(
  devm_kzalloc(HANDLE,
-	(sizeof(TYPE)) * E
+	sizeof(TYPE) * E
  , ...)
|
  devm_kzalloc(HANDLE,
-	(sizeof(THING)) * E
+	sizeof(THING) * E
  , ...)
)

// Drop single-byte sizes and redundant parens.
@@
expression HANDLE;
expression COUNT;
typedef u8;
typedef __u8;
@@

(
  devm_kzalloc(HANDLE,
-	sizeof(u8) * (COUNT)
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(__u8) * (COUNT)
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(char) * (COUNT)
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(unsigned char) * (COUNT)
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(u8) * COUNT
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(__u8) * COUNT
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(char) * COUNT
+	COUNT
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(unsigned char) * COUNT
+	COUNT
  , ...)
)

// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
expression HANDLE;
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@

(
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * (COUNT_ID)
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * COUNT_ID
+	COUNT_ID, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * (COUNT_CONST)
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * COUNT_CONST
+	COUNT_CONST, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * (COUNT_ID)
+	COUNT_ID, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * COUNT_ID
+	COUNT_ID, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * (COUNT_CONST)
+	COUNT_CONST, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * COUNT_CONST
+	COUNT_CONST, sizeof(THING)
  , ...)
)

// 2-factor product, only identifiers.
@@
expression HANDLE;
identifier SIZE, COUNT;
@@

- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	SIZE * COUNT
+	COUNT, SIZE
  , ...)

// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression HANDLE;
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@

(
  devm_kzalloc(HANDLE,
-	sizeof(TYPE) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(TYPE))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING) * (COUNT) * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING) * (COUNT) * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING) * COUNT * (STRIDE)
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING) * COUNT * STRIDE
+	array3_size(COUNT, STRIDE, sizeof(THING))
  , ...)
)

// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression HANDLE;
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@

(
  devm_kzalloc(HANDLE,
-	sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(THING1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(THING1), sizeof(THING2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE1) * sizeof(THING2) * COUNT
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
|
  devm_kzalloc(HANDLE,
-	sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+	array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
  , ...)
)

// 3-factor product, only identifiers, with redundant parens removed.
@@
expression HANDLE;
identifier STRIDE, SIZE, COUNT;
@@

(
  devm_kzalloc(HANDLE,
-	(COUNT) * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	COUNT * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	COUNT * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(COUNT) * (STRIDE) * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	COUNT * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(COUNT) * STRIDE * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(COUNT) * (STRIDE) * (SIZE)
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
|
  devm_kzalloc(HANDLE,
-	COUNT * STRIDE * SIZE
+	array3_size(COUNT, STRIDE, SIZE)
  , ...)
)

// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression HANDLE;
expression E1, E2, E3;
constant C1, C2, C3;
@@

(
  devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
  devm_kzalloc(HANDLE,
-	(E1) * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(E1) * (E2) * E3
+	array3_size(E1, E2, E3)
  , ...)
|
  devm_kzalloc(HANDLE,
-	(E1) * (E2) * (E3)
+	array3_size(E1, E2, E3)
  , ...)
|
  devm_kzalloc(HANDLE,
-	E1 * E2 * E3
+	array3_size(E1, E2, E3)
  , ...)
)

// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression HANDLE;
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@

(
  devm_kzalloc(HANDLE, sizeof(THING) * C2, ...)
|
  devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...)
|
  devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
  devm_kzalloc(HANDLE, C1 * C2, ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * (E2)
+	E2, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(TYPE) * E2
+	E2, sizeof(TYPE)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * (E2)
+	E2, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	sizeof(THING) * E2
+	E2, sizeof(THING)
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	(E1) * E2
+	E1, E2
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	(E1) * (E2)
+	E1, E2
  , ...)
|
- devm_kzalloc
+ devm_kcalloc
  (HANDLE,
-	E1 * E2
+	E1, E2
  , ...)
)

Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-12 16:19:22 -07:00
James Bottomley 2be8ffed09 tpm: fix intermittent failure with self tests
My Nuvoton 6xx in a Dell XPS-13 has been intermittently failing to work
(necessitating a reboot). The problem seems to be that the TPM gets into a
state where the partial self-test doesn't return TPM_RC_SUCCESS (meaning
all tests have run to completion), but instead returns TPM_RC_TESTING
(meaning some tests are still running in the background).  There are
various theories that resending the self-test command actually causes the
tests to restart and thus triggers more TPM_RC_TESTING returns until the
timeout is exceeded.

There are several issues here: firstly being we shouldn't slow down the
boot sequence waiting for the self test to complete once the TPM
backgrounds them.  It will actually make available all functions that have
passed and if it gets a failure return TPM_RC_FAILURE to every subsequent
command.  So the fix is to kick off self tests once and if they return
TPM_RC_TESTING log that as a backgrounded self test and continue on.  In
order to prevent other tpm users from seeing any TPM_RC_TESTING returns
(which it might if they send a command that needs a TPM subsystem which is
still under test), we loop in tpm_transmit_cmd until either a timeout or we
don't get a TPM_RC_TESTING return.

Finally, there have been observations of strange returns from a partial
test. One Nuvoton is occasionally returning TPM_RC_COMMAND_CODE, so treat
any unexpected return from a partial self test as an indication we need to
run a full self test.

[jarkko.sakkinen@linux.intel.com: cleaned up some klog messages and
 dropped tpm_transmit_check() helper function from James' original
 commit.]

Fixes: 2482b1bba5 ("tpm: Trigger only missing TPM 2.0 self tests")
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
2018-03-23 10:25:09 +02:00
Tomas Winkler 076d356460 tpm2: add longer timeouts for creation commands.
TPM2_CC_Create(0x153) and TPM2_CC_CreatePrimary (0x131) involve generation
of crypto keys which can be a computationally intensive task. The timeout
is set to 3min. Rather than increasing default timeout a new constant is
added, to not stall for too long on regular commands failures.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-03-23 10:18:06 +02:00
Jeremy Boone 3be2327475 tpm: fix potential buffer overruns caused by bit glitches on the bus
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips.  If a bit does
flip it could cause an overrun if it's in one of the size parameters,
so sanity check that we're not overrunning the provided buffer when
doing a memcpy().

Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
2018-02-26 15:43:46 -08:00
Alexander.Steffen@infineon.com 0b66f2a05a tpm2-cmd: allow more attempts for selftest execution
Previously, if the last attempt to execute the selftest command failed with
RC_TESTING, there was still a call to tpm_msleep, even though no further
attempt would be made. This causes an unnecessary delay, therefore ensure
that if the last attempt fails the function is left immediately.

Also, instead of ensuring that the cumulated runtime of all attempts is
larger than the command duration for TPM2_SelfTest, ensure that there is at
least one attempt for which the delay is larger than the expected command
duration. This allows slow TPMs to execute all their tests in the
background, without slowing down faster TPMs that have finished their tests
earlier. If tests are still not finished even with this long delay, then
something is broken and the TPM is not used.

Fixes: 125a221054 ("tpm: React correctly to RC_TESTING from TPM 2.0 self
tests")

Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2018-01-08 12:58:37 +02:00
Jarkko Sakkinen 171360d780 tpm: fix type of a local variable in tpm2_get_cc_attrs_tbl()
The local variable 'attrs' should have the type __be32 instead of u32.

Fixes: 58472f5cd4 ("tpm: validate TPM 2.0 commands")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
2017-10-18 18:28:48 +03:00
Alexander Steffen 125a221054 tpm: React correctly to RC_TESTING from TPM 2.0 self tests
The TPM can choose one of two ways to react to the TPM2_SelfTest command.
It can either run all self tests synchronously and then return RC_SUCCESS
once all tests were successful. Or it can choose to run the tests
asynchronously and return RC_TESTING immediately while the self tests still
execute in the background.

The previous implementation apparently was not aware of those possibilities
and attributed RC_TESTING to some prototype chips instead. With this change
the return code of TPM2_SelfTest is interpreted correctly, i.e. the self
test result is polled if and only if RC_TESTING is received.

Unfortunately, the polling cannot be done in the most straightforward way.
If RC_TESTING is received, ideally the code should now poll the
selfTestDone bit in the STS register, as this avoids sending more commands,
that might interrupt self tests executing in the background and thus
prevent them from ever completing. But it cannot be guaranteed that this
bit is correctly implemented for all devices, so the next best thing would
be to use TPM2_GetTestResult to query the test result. But the response to
that command can be very long, and the code currently lacks the
capabilities for efficient unmarshalling, so it is difficult to execute
this command.

Therefore, we simply run the TPM2_SelfTest command in a loop, which should
complete eventually, since we only request the execution of self tests that
have not yet been done.

Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-10-18 18:28:47 +03:00
Alexander Steffen 87434f58be tpm: Use dynamic delay to wait for TPM 2.0 self test result
In order to avoid delaying the code longer than necessary while still
giving the TPM enough time to execute the self tests asynchronously, start
with a small delay between two polls and increase it each round.

Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-10-18 18:28:46 +03:00
Alexander Steffen 2482b1bba5 tpm: Trigger only missing TPM 2.0 self tests
tpm2_do_selftest is only used during initialization of the TPM to ensure
that the device functions correctly. Therefore, it is sufficient to request
only missing self tests (parameter full_test=0), not a reexecution of all
self tests, as was done before. This allows for a faster execution of this
command.

Signed-off-by: Alexander Steffen <Alexander.Steffen@infineon.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-10-18 18:28:46 +03:00
Hamza Attak 9f3fc7bcdd tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers
The patch simply replaces all msleep function calls with usleep_range calls
in the generic drivers.

Tested with an Infineon TPM 1.2, using the generic tpm-tis module, for a
thousand PCR extends, we see results going from 1m57s unpatched to 40s
with the new patch. We obtain similar results when using the original and
patched tpm_infineon driver, which is also part of the patch.
Similarly with a STM TPM 2.0, using the CRB driver, it takes about 20ms per
extend unpatched and around 7ms with the new patch.

Note that the PCR consistency is untouched with this patch, each TPM has
been tested with 10 million extends and the aggregated PCR value is
continuously verified to be correct.

As an extension of this work, this could potentially and easily be applied
to other vendor's drivers. Still, these changes are not included in the
proposed patch as they are untested.

Signed-off-by: Hamza Attak <hamza@hpe.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2017-09-23 21:51:00 -07:00
Roberto Sassu 28707bf221 tpm: use tpm2_pcr_read() in tpm2_do_selftest()
tpm2_do_selftest() performs a PCR read during the TPM initialization phase.
This patch replaces the PCR read code with a call to tpm2_pcr_read().

Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2017-07-07 09:49:26 +10:00
Roberto Sassu 91f7f3d773 tpm: use tpm_buf functions in tpm2_pcr_read()
tpm2_pcr_read() now builds the PCR read command buffer with tpm_buf
functions. This solution is preferred to using a tpm2_cmd structure,
as tpm_buf functions provide protection against buffer overflow.

Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2017-07-07 09:49:25 +10:00
Jarkko Sakkinen 19cbe4f680 tpm: consolidate the TPM startup code
Consolidated all the "manual" TPM startup code to a single function
in order to make code flows a bit cleaner and migrate to tpm_buf.

Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
2017-07-07 09:49:25 +10:00
Stefan Berger 402149c647 tpm: vtpm_proxy: Suppress error logging when in closed state
Suppress the error logging when the core TPM driver sends commands
to the VTPM proxy driver and -EPIPE is returned in case the VTPM
proxy driver is 'closed' (closed anonymous file descriptor).  This
error code is only returned by the send function and by tpm_transmit
when the VTPM proxy driver is being used.

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-06-13 22:02:09 +03:00
Jarkko Sakkinen 745b361e98 tpm: infrastructure for TPM spaces
Added an ability to virtualize TPM commands into an isolated context
that we call a TPM space because the word context is already heavily
used in the TPM specification. Both the handle areas and bodies (where
necessary) are virtualized.

The mechanism works by adding a new parameter struct tpm_space to the
tpm_transmit() function. This new structure contains the list of virtual
handles and a buffer of page size (currently) for backing storage.

When tpm_transmit() is called with a struct tpm_space instance it will
execute the following sequence:

1. Take locks.
2. Load transient objects from the backing storage by using ContextLoad
   and map virtual handles to physical handles.
3. Perform the transaction.
4. Save transient objects to backing storage by using ContextSave and
   map resulting physical handle to virtual handle if there is such.

This commit does not implement virtualization support for hmac and
policy sessions.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2017-04-03 22:46:01 +03:00
Jarkko Sakkinen 58472f5cd4 tpm: validate TPM 2.0 commands
Check for every TPM 2.0 command that the command code is supported and
the command buffer has at least the length that can contain the header
and the handle area.

For ContextSave and FlushContext we mark the body to be part of the
handle area. This gives validation for these commands at zero
cost, including the body of the command.

The more important reason for this is that we can virtualize these
commands in the same way as you would virtualize the handle area of a
command.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2017-04-03 22:46:01 +03:00
Jarkko Sakkinen 9aa36b399a tpm: export tpm2_flush_context_cmd
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2017-04-03 22:46:01 +03:00
Jarkko Sakkinen 61841be635 tpm: declare tpm2_get_pcr_allocation() as static
There's no need to export tpm2_get_pcr_alloation() because it is only
a helper function for tpm2_auto_startup(). For the same reason it does
not make much sense to maintain documentation for it.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-02-20 13:23:18 +02:00
Nayna Jain c1f92b4b04 tpm: enhance TPM 2.0 PCR extend to support multiple banks
The current TPM 2.0 device driver extends only the SHA1 PCR bank
but the TCG Specification[1] recommends extending all active PCR
banks, to prevent malicious users from setting unused PCR banks with
fake measurements and quoting them.

The existing in-kernel interface(tpm_pcr_extend()) expects only a
SHA1 digest.  To extend all active PCR banks with differing
digest sizes, the SHA1 digest is padded with trailing 0's as needed.

This patch reuses the defined digest sizes from the crypto subsystem,
adding a dependency on CRYPTO_HASH_INFO module.

[1] TPM 2.0 Specification referred here is "TCG PC Client Specific
Platform Firmware Profile for TPM 2.0"

Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Kenneth Goldman <kgold@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-02-03 22:03:14 +02:00
Nayna Jain 1db15344f8 tpm: implement TPM 2.0 capability to get active PCR banks
This patch implements the TPM 2.0 capability TPM_CAP_PCRS to
retrieve the active PCR banks from the TPM. This is needed
to enable extending all active banks as recommended by TPM 2.0
TCG Specification.

Signed-off-by: Nayna Jain <nayna@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Kenneth Goldman <kgold@linux.vnet.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-02-03 22:03:14 +02:00
Jarkko Sakkinen 7d761119a9 tpm: fix RC value check in tpm2_seal_trusted
The error code handling is broken as any error code that has the same
bits set as TPM_RC_HASH passes. Implemented tpm2_rc_value() helper to
parse the error value from FMT0 and FMT1 error codes so that these types
of mistakes are prevented in the future.

Fixes: 5ca4c20cfd ("keys, trusted: select hash algorithm for TPM2 chips")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
2017-02-03 22:03:14 +02:00
Stefan Berger c659af78eb tpm: Check size of response before accessing data
Make sure that we have not received less bytes than what is indicated
in the header of the TPM response. Also, check the number of bytes in
the response before accessing its data.

Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
2017-01-23 18:28:18 +02:00
Winkler, Tomas 794c6e109b tpm/tpm2-chip: fix kdoc errors
Use correct kdoc format, describe correct parameters and return values.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2017-01-23 18:28:18 +02:00
Baruch Siach cbef69a9e1 char: tpm: fix kerneldoc tpm2_unseal_trusted name typo
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-11-28 01:31:31 +02:00
Jarkko Sakkinen ae7e190a3e tpm: use tpm_transmit_cmd() in tpm2_probe()
It is better to tpm_transmit_cmd() in tpm2_probe() in order to get
consistent command handling throughout the subsystem.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
2016-09-15 16:04:21 +03:00
Jarkko Sakkinen eb5854e764 tpm: replace tpm_gen_interrupt() with tpm_tis_gen_interrupt()
Since tpm_gen_interrupt() is only used in tpm_tis_core.c this commit
replaces it with an internal tpm_tis_gen_interrupt(). The semantics
also changed in a way that on a system error the driver initialization
is failed.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
2016-09-15 16:04:21 +03:00
Jarkko Sakkinen d4816edfe7 tpm: fix a race condition in tpm2_unseal_trusted()
Unseal and load operations should be done as an atomic operation. This
commit introduces unlocked tpm_transmit() so that tpm2_unseal_trusted()
can do the locking by itself.

Fixes: 0fe5480303 ("keys, trusted: seal/unseal with TPM 2.0 chips")
Cc: stable@vger.kernel.org
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
2016-09-15 16:04:21 +03:00
Jarkko Sakkinen b7d7b28471 tpm: invalid self test error message
The driver emits invalid self test error message even though the init
succeeds.

Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Fixes: cae8b441fc ("tpm: Factor out common startup code")
Reviewed-by: James Morris <james.l.morris@oracle.com>
2016-09-15 16:04:21 +03:00
Jason Gunthorpe cae8b441fc tpm: Factor out common startup code
The TCG standard startup sequence (get timeouts, tpm startup, etc) for
TPM and TPM2 chips is being open coded in many drivers, move it into
the core code.

tpm_tis and tpm_crb are used as the basis for the core code
implementation and the easy drivers are converted. In the process
several small drivers bugs relating to error handling this flow
are fixed.

For now the flag TPM_OPS_AUTO_STARTUP is optional to allow a staged
driver roll out, but ultimately all drivers should use this flow and
the flag removed. Some drivers still do not implement the startup
sequence at all and will need to be tested with it enabled.

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Andrew Zamansky <andrew.zamansky@nuvoton.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-07-19 17:43:38 +03:00
apronin@chromium.org 1b0612b040 tpm: fix byte-order for the value read by tpm2_get_tpm_pt
The result must be converted from BE byte order, which is used by the
TPM2 protocol. This has not popped out because tpm2_get_tpm_pt() has
been only used for probing.

Fixes: 7a1d7e6dd7 ("tpm: TPM 2.0 baseline support")
Change-Id: I7d71cd379b1a3b7659d20a1b6008216762596590
Signed-off-by: Andrey Pronin <apronin@chromium.org>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-07-19 17:43:38 +03:00
Christophe Ricard af782f339a tpm: Move tpm_vendor_specific data related with PTP specification to tpm_chip
Move tpm_vendor_specific data related to TCG PTP specification to tpm_chip.

Move all fields directly linked with well known TCG concepts and used in
TPM drivers (tpm_i2c_atmel, tpm_i2c_infineon, tpm_i2c_nuvoton, tpm_tis
and xen-tpmfront) as well as in TPM core files (tpm-sysfs, tpm-interface
and tpm2-cmd) in tpm_chip.

Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-06-25 17:26:35 +03:00
Jarkko Sakkinen dcbeab1946 tpm: fix crash in tpm_tis deinitialization
rmmod crashes the driver because tpm_chip_unregister() already sets ops
to NULL. This commit fixes the issue by moving tpm2_shutdown() to
tpm_chip_unregister(). This commit is also cleanup because it removes
duplicate code from tpm_crb and tpm_tis to the core.

Fixes: 4d3eac5e156a ("tpm: Provide strong locking for device removal")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
2016-06-25 17:26:35 +03:00
Jason Gunthorpe 8cfffc9d4d tpm: Get rid of chip->pdev
This is a hold over from before the struct device conversion.

- All prints should be using &chip->dev, which is the Linux
  standard. This changes prints to use tpm0 as the device name,
  not the PnP/etc ID.
- The few places involving sysfs/modules that really do need the
  parent just use chip->dev.parent instead
- We no longer need to get_device(pdev) in any places since it is no
  longer used by any of the code. The kref on the parent is held
  by the device core during device_add and dropped in device_del

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
2016-06-25 17:26:35 +03:00