Граф коммитов

152 Коммитов

Автор SHA1 Сообщение Дата
Dave Jiang 1ca1e43e55 [SCSI] libsas: Add option for SATA soft reset
This allows a libsas driver to optionally provide a soft reset handler
for libata to drive.  The isci driver allows software to control the
assertion/deassertion of SRST.

[jejb: checkpatch.pl fixes]
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-26 22:49:33 -05:00
Dan Williams 3673f4bf6a [SCSI] libsas: check dev->gone before submitting sata i/o
Head off doomed-to-fail i/o in sas_queuecommand before sending it down
the ata path.

Before:
sd 7:0:0:0: [sdd] Synchronizing SCSI cache
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
sd 7:0:0:0: [sdd]  Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 7:0:0:0: [sdd]  Sense Key : Aborted Command [current] [descriptor]
sd 7:0:0:0: [sdd]  Add. Sense: No additional sense information
sd 7:0:0:0: [sdd] Stopping disk

After:
sd 9:0:0:0: [sdd] Synchronizing SCSI cache
sd 9:0:0:0: [sdd]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 9:0:0:0: [sdd] Stopping disk
sd 9:0:0:0: [sdd] START_STOP FAILED
sd 9:0:0:0: [sdd]  Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK

This is a cosmetic change as sata i/o can still leak to a gone device,
but this addresses the nominal hotplug case when releasing the target.

Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-26 22:49:33 -05:00
Dan Williams 90f1e10d08 [SCSI] libsas: fix/amend device gone notification in sas_deform_port()
Commit 56dd2c06 "libsas: Don't issue commands to devices that have been
hot-removed" edited Darrick's original patch to remove setting 'gone' in
the sas_deform_port() path because that prevented scsi sync cache
commands from being issued when the driver was unloaded.  However, this
allows true device gone notifications (as signaled port phy events) to
trigger sync cache commands to devices that are known to be unreachable.

Teach libsas which sas_deform_port() invocations are likely device gone
events.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-26 22:49:32 -05:00
Xiangliang Yu bb650a1bef [SCSI] libsas: fix SATA NCQ error
Current version of libsas can not handle SATA NCQ error.
This patch handle SATA NCQ error as AHCI do.

Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-24 12:34:01 -04:00
Lucas De Marchi 25985edced Fix common misspellings
Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-31 11:26:23 -03:00
Linus Torvalds a44f99c7ef Merge branch 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (25 commits)
  video: change to new flag variable
  scsi: change to new flag variable
  rtc: change to new flag variable
  rapidio: change to new flag variable
  pps: change to new flag variable
  net: change to new flag variable
  misc: change to new flag variable
  message: change to new flag variable
  memstick: change to new flag variable
  isdn: change to new flag variable
  ieee802154: change to new flag variable
  ide: change to new flag variable
  hwmon: change to new flag variable
  dma: change to new flag variable
  char: change to new flag variable
  fs: change to new flag variable
  xtensa: change to new flag variable
  um: change to new flag variables
  s390: change to new flag variable
  mips: change to new flag variable
  ...

Fix up trivial conflict in drivers/hwmon/Makefile
2011-03-20 18:14:55 -07:00
Linus Torvalds c55d267de2 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (170 commits)
  [SCSI] scsi_dh_rdac: Add MD36xxf into device list
  [SCSI] scsi_debug: add consecutive medium errors
  [SCSI] libsas: fix ata list corruption issue
  [SCSI] hpsa: export resettable host attribute
  [SCSI] hpsa: move device attributes to avoid forward declarations
  [SCSI] scsi_debug: Logical Block Provisioning (SBC3r26)
  [SCSI] sd: Logical Block Provisioning update
  [SCSI] Include protection operation in SCSI command trace
  [SCSI] hpsa: fix incorrect PCI IDs and add two new ones (2nd try)
  [SCSI] target: Fix volume size misreporting for volumes > 2TB
  [SCSI] bnx2fc: Broadcom FCoE offload driver
  [SCSI] fcoe: fix broken fcoe interface reset
  [SCSI] fcoe: precedence bug in fcoe_filter_frames()
  [SCSI] libfcoe: Remove stale fcoe-netdev entries
  [SCSI] libfcoe: Move FCOE_MTU definition from fcoe.h to libfcoe.h
  [SCSI] libfc: introduce __fc_fill_fc_hdr that accepts fc_hdr as an argument
  [SCSI] fcoe, libfc: initialize EM anchors list and then update npiv EMs
  [SCSI] Revert "[SCSI] libfc: fix exchange being deleted when the abort itself is timed out"
  [SCSI] libfc: Fixing a memory leak when destroying an interface
  [SCSI] megaraid_sas: Version and Changelog update
  ...

Fix up trivial conflicts due to whitespace differences in
drivers/scsi/libsas/{sas_ata.c,sas_scsi_host.c}
2011-03-17 17:54:40 -07:00
matt mooney bfbec92075 scsi: change to new flag variable
Replace EXTRA_CFLAGS with ccflags-y.

Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
2011-03-17 14:05:35 +01:00
James Bottomley a82058a730 [SCSI] libsas: fix ata list corruption issue
I think this stems from a misunderstanding of how the ata error handler
works.  ata_scsi_cmd_error_handler() gets called with a passed in list
of commands to handle.  However, that list may still not be empty when
it exits.  The command ata_scsi_port_error_handler() must be called
(which takes no list) before the list will be completely emptied.  This
bites the sas error handler because the two are called from different
functions and the original list has gone out of scope before
ata_scsi_port_error_handler() is called. leading to some commands
dangling on bare stack, which is a potential memory corruption issue.
Fix this by manually deleting all outstanding commands from the on-stack
list before it goes out of scope.

Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-03-14 18:46:25 -05:00
Sergei Shtylyov 9cbe056f6c libata: remove ATA_FLAG_NO_LEGACY
All checks of ATA_FLAG_NO_LEGACY have been removed by the commits
c791c30670 ([libata] minor PCI IDE probe
fixes and cleanups) and f0d36efdc6 (libata:
update libata core layer to use devres), so I think it's time to finally
get rid of this flag...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-03-02 02:36:46 -05:00
Sergei Shtylyov 3696df3099 libata: remove ATA_FLAG_MMIO
Commit 0d5ff56677 (libata: convert to iomap)
removed all checks of ATA_FLAG_MMIO but neglected to remove the flag itself.
Do it now, at last...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-03-02 02:36:46 -05:00
Sergei Shtylyov c10f97b9d8 libata: remove ATA_FLAG_{SRST|SATA_RESET}
These flags are marked as obsolete and the checks for them have been removed
by commit 294440887b (libata-sff: kill unused
ata_bus_reset()), so I think it's time to finally get rid of them...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-03-02 02:36:46 -05:00
Sergei Shtylyov 0f2e0330a8 ipr/sas_ata: use mode mask macros from <linux/ata.h>
Commit 14bdef982c ([libata] convert drivers to
use ata.h mode mask defines) didn't convert these two libata driver outside
drivers/ata/...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-03-02 02:36:46 -05:00
James Bottomley 00dd4998a6 libsas: convert to libata new error handler
The conversion is quite complex given that the libata new error
handler has to be hooked into the current libsas timeout and error
handling.  The way this is done is to process all the failed commands
via libsas first, but if they have no underlying sas task (and they're
on a sata device) assume they are destined for the libata error
handler and send them accordingly.

Finally, activate the port recovery of the libata error handler for
each port known to the host.  This is somewhat suboptimal, since that
port may not need recovering, but given the current architecture of
the libata error handler, it's the only way; and the spurious
activation is harmless.

Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-03-02 02:36:45 -05:00
jack_wang 183ce896d7 [SCSI] libsas: fix loopback topology bug during discovery
In some test envirenment, there is loopback topology test. We should
handle this during discovery.

Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-02-28 11:40:34 -06:00
James Bottomley c299190b93 [SCSI] libsas: convert to libata new error handler
The conversion is quite complex given that the libata new error
handler has to be hooked into the current libsas timeout and error
handling.  The way this is done is to process all the failed commands
via libsas first, but if they have no underlying sas task (and they're
on a sata device) assume they are destined for the libata error
handler and send them accordingly.

Finally, activate the port recovery of the libata error handler for
each port known to the host.  This is somewhat suboptimal, since that
port may not need recovering, but given the current architecture of
the libata error handler, it's the only way; and the spurious
activation is harmless.

Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-02-13 13:17:46 -06:00
James Bottomley 1e34c83873 [SCSI] libsas: remove spurious sata control register read/write
Originally, libata required the illusion that it could access the sata
control register.  Now, however, it can run perfectly well without
them, so remove the dummy routines from libsas which tried to emulate
them (but only ended up causing confusion).

Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-01-24 12:05:45 -06:00
James Bottomley 96db6fa992 [SCSI] libsas: convert to standard kernel debugging
Instead of using a config option for debugging, just dump the
messages with KERN_DEBUG.

Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-01-24 12:05:38 -06:00
James Bottomley 75c0b3867b [SCSI] libsas: fix ATAPI check condition termination
ATAPI check condition needs to be treated the same as a success or
protocol return.  The register returns from the PACKET command are all
correctly positioned in the device to host register FIS and so we
should collect them properly.  Right at the moment this doesn't matter
because libata sends a request sense always for ATAPI errors, but if
it ever checked the registers, we should have the correct contents
just in case.

Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-01-24 12:05:22 -06:00
James Bottomley 9ee91f7fb5 [SCSI] libsas: fix runaway error handler problem
libsas makes use of scsi_schedule_eh() but forgets to clear the
host_eh_scheduled flag in its error handling routine.  Because of this,
the error handler thread never gets to sleep; it's constantly awake and
trying to run the error routine leading to console spew and inability to
run anything else (at least on a UP system).  The fix is to clear the
flag as we splice the work queue.

Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-01-24 11:52:33 -06:00
Linus Torvalds 1542dec1c9 Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  pata_platform: Remove CONFIG_HAVE_PATA_PLATFORM's dependencies.
  pata_hpt37x: actually limit HPT370 to UltraDMA/66
  pata_hpt3x2n: coding style cleanup
  pata_hpt37x: coding style cleanup
  pata_hpt366: coding style cleanup
  pata_hpt3x2n: calculate average f_CNT
  pata_hpt3x2n: clarify about HPT371N support
  pata_hpt{37x|3x2n}: SATA mode filtering
  [libata] avoid needlessly passing around ptr to SCSI completion func
  [libata] new driver acard_ahci, for ATP8620 host controller
2011-01-10 08:22:33 -08:00
Jeff Garzik b27dcfb067 [libata] avoid needlessly passing around ptr to SCSI completion func
It's stored in struct scsi_cmnd->scsi_done, making several 'done'
parameters to functions redundant.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-01-05 19:43:22 -05:00
Dan Williams 00f0254ed9 [SCSI] libsas: fix definition of wideport, include local sas address
To date libsas has only looked at the attached sas address when
determining the formation of wide ports.  The specification and some
hardware expects that phys with different addresses will not form a wide
port unless the local peer phys also match each other.  Introduce a flag
to select stricter behavior at sas_register_ha() time.  The flag can be
dropped once it is known that all libsas users expect the same behavior.

Current drivers just initialize this field to zero and get the
traditional behavior.

Reported-by: Patrick Thomson <patrick.s.thomson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-12-21 12:23:53 -06:00
Jeff Garzik f281233d3e SCSI host lock push-down
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.

The patch below presents a simple SCSI host lock push-down as an
equivalent transformation.  No locking or other behavior should change
with this patch.  All existing bugs and locking orders are preserved.

Additionally, add one parameter to queuecommand,
	struct Scsi_Host *
and remove one parameter from queuecommand,
	void (*done)(struct scsi_cmnd *)

Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.

Minimal code disturbance was attempted with this change.  Most drivers
needed only two one-line modifications for their host lock push-down.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-11-16 13:33:23 -08:00
Linus Torvalds c70b5296e7 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (84 commits)
  [SCSI] be2iscsi: SGE Len == 64K
  [SCSI] be2iscsi: Remove premature free of cid
  [SCSI] be2iscsi: More time for FW
  [SCSI] libsas: fix bug for vacant phy
  [SCSI] sd: Fix overflow with big physical blocks
  [SCSI] st: add MTWEOFI to write filemarks without flushing drive buffer
  [SCSI] libsas: Don't issue commands to devices that have been hot-removed
  [SCSI] megaraid_sas: Add Online Controller Reset to MegaRAID SAS drive
  [SCSI] lpfc 8.3.17: Update lpfc driver version to 8.3.17
  [SCSI] lpfc 8.3.17: Replace function reset methodology
  [SCSI] lpfc 8.3.17: SCSI fixes
  [SCSI] lpfc 8.3.17: BSG fixes
  [SCSI] lpfc 8.3.17: SLI Additions and Fixes
  [SCSI] lpfc 8.3.17: Code Cleanup and Locking fixes
  [SCSI] zfcp: Remove scsi_cmnd->serial_number from debug traces
  [SCSI] ipr: fix array error logging
  [SCSI] aha152x: enable PCMCIA on 64bit
  [SCSI] scsi_dh_alua: Handle all states correctly
  [SCSI] cxgb4i: connection and ddp setting update
  [SCSI] cxgb3i: fixed connection over vlan
  ...
2010-10-22 17:34:15 -07:00
Jack Wang 2bc72c91ea [SCSI] libsas: fix bug for vacant phy
This patch fix bug reported by Chuck. And this new version incorporate comments
from Hannes. Please consider to include it into mainline.

Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Tested-by: Chuck Tuffli <Chuck_Tuffli@pmc-sierra.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-11 17:40:00 -05:00
Darrick J. Wong 56dd2c0691 [SCSI] libsas: Don't issue commands to devices that have been hot-removed
sd will get hung up issuing commands to flush write cache if a SAS
device behind the expander is unplugged without warning.  Change libsas
to reject commands to domain devices that have already gone away.

[maciej.trela@intel.com: removed setting ->gone in sas_deform_port() to
 permit sync cache commands at module removal]

Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Tested-by: Haipao Fan <haipao.fan@intel.com>
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-08 16:03:42 -05:00
David Milburn f0ad30d3d2 [SCSI] libsas: fix NCQ mixing with non-NCQ
Some cards (like mvsas) have issue troubles if non-NCQ commands are
mixed with NCQ ones.  Fix this by using the libata default NCQ check
routine which waits until all NCQ commands are complete before issuing
a non-NCQ one.  The impact to cards (like aic94xx) which don't need
this logic should be minimal

Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-07 17:06:03 -05:00
Tejun Heo 9cbbdca44a block: remove spurious uses of REQ_HARDBARRIER
REQ_HARDBARRIER is deprecated.  Remove spurious uses in the following
users.  Please note that other than osdblk, all other uses were
already spurious before deprecation.

* osdblk: osdblk_rq_fn() won't receive any request with
  REQ_HARDBARRIER set.  Remove the test for it.

* pktcdvd: use of REQ_HARDBARRIER in pkt_generic_packet() doesn't mean
  anything.  Removed.

* aic7xxx_old: Setting MSG_ORDERED_Q_TAG on REQ_HARDBARRIER is
  spurious.  Removed.

* sas_scsi_host: Setting TASK_ATTR_ORDERED on REQ_HARDBARRIER is
  spurious.  Removed.

* scsi_tcq: The ordered tag path wasn't being used anyway.  Removed.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@suse.de>
Cc: Peter Osterlund <petero2@telia.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2010-09-10 12:35:36 +02:00
James Bottomley df64d3caab [SCSI] Unify SAM_ and SAM_STAT_ macros
We have two separate definitions for identical constants with nearly the
same name.  One comes from the generic headers in scsi.h; the other is
an enum in libsas.h ... it's causing confusion about which one is
correct (fortunately they both are).

Fix this by eliminating the libsas.h duplicate

Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-07-28 09:07:49 -05:00
Linus Torvalds 33cf23b0a5 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (182 commits)
  [SCSI] aacraid: add an ifdef'd device delete case instead of taking the device offline
  [SCSI] aacraid: prohibit access to array container space
  [SCSI] aacraid: add support for handling ATA pass-through commands.
  [SCSI] aacraid: expose physical devices for models with newer firmware
  [SCSI] aacraid: respond automatically to volumes added by config tool
  [SCSI] fcoe: fix fcoe module ref counting
  [SCSI] libfcoe: FIP Keep-Alive messages for VPorts are sent with incorrect port_id and wwn
  [SCSI] libfcoe: Fix incorrect MAC address clearing
  [SCSI] fcoe: fix a circular locking issue with rtnl and sysfs mutex
  [SCSI] libfc: Move the port_id into lport
  [SCSI] fcoe: move link speed checking into its own routine
  [SCSI] libfc: Remove extra pointer check
  [SCSI] libfc: Remove unused fc_get_host_port_type
  [SCSI] fcoe: fixes wrong error exit in fcoe_create
  [SCSI] libfc: set seq_id for incoming sequence
  [SCSI] qla2xxx: Updates to ISP82xx support.
  [SCSI] qla2xxx: Optionally disable target reset.
  [SCSI] qla2xxx: ensure flash operation and host reset via sg_reset are mutually exclusive
  [SCSI] qla2xxx: Silence bogus warning by gcc for wrap and did.
  [SCSI] qla2xxx: T10 DIF support added.
  ...
2010-05-21 07:19:18 -07:00
Tejun Heo 3e4ec3443f libata: kill ATA_FLAG_DISABLED
ATA_FLAG_DISABLED is only used by drivers which don't use
->error_handler framework and is largely broken.  Its only meaningful
function is to make irq handlers skip processing if the flag is set,
which is largely useless and even harmful as it makes those ports more
likely to cause IRQ storms.

Kill ATA_FLAG_DISABLED and makes the callers disable attached devices
instead.  ata_port_probe() and ata_port_disable() which manipulate the
flag are also killed.

This simplifies condition check in IRQ handlers.  While updating IRQ
handlers, remove ap NULL check as libata guarantees consecutive port
allocation (unoccupied ports are initialized with dummies) and
long-obsolete ATA_QCFLAG_ACTIVE check (checked by ata_qc_from_tag()).

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-05-17 22:49:02 -04:00
James Bottomley 1b4d0d8ea7 [SCSI] libsas: fix deref before check in commit 70b25f890c
commit 70b25f890c
Author: Tejun Heo <tj@kernel.org>
Date:   Thu Apr 15 09:00:08 2010 +0900

    [SCSI] fix locking around blk_abort_request()

Introduced a reference before check problem, fix this by moving the
lock shorthand code to be right at the point of actual use.

Reported-by: Dan Carpenter <error27@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-05-16 15:34:58 -04:00
Tejun Heo 70b25f890c [SCSI] fix locking around blk_abort_request()
blk_abort_request() expects queue lock to be held by the caller.
Grab it before calling the function.

Lack of this synchronization led to infinite loop on corrupt
q->timeout_list.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-05-01 14:17:19 -05:00
Tejun Heo 5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Linus Torvalds 382f51fe2f Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
  [SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
  [SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
  [SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
  [SCSI] zfcp: Update FSF error reporting
  [SCSI] zfcp: Improve ELS ADISC handling
  [SCSI] zfcp: Simplify handling of ct and els requests
  [SCSI] zfcp: Remove ZFCP_DID_MASK
  [SCSI] zfcp: Move WKA port to zfcp FC code
  [SCSI] zfcp: Use common code definitions for FC CT structs
  [SCSI] zfcp: Use common code definitions for FC ELS structs
  [SCSI] zfcp: Update FCP protocol related code
  [SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
  [SCSI] zfcp: Assign scheduled work to driver queue
  [SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
  [SCSI] zfcp: Implement module unloading
  [SCSI] zfcp: Merge trace code for fsf requests in one function
  [SCSI] zfcp: Access ports and units with container_of in sysfs code
  [SCSI] zfcp: Remove suspend callback
  [SCSI] zfcp: Remove global config_mutex
  [SCSI] zfcp: Replace local reference counting with common kref
  ...
2009-12-09 19:42:25 -08:00
Mike Christie e881a172da [SCSI] modify change_queue_depth to take in reason why it is being called
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.

This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>

[Vasu.Dev: v2
	Also converted pmcraid_change_queue_depth and then verified
all modules compile  using "make allmodconfig" for any new build
warnings on X86_64.

	Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-12-04 12:00:41 -06:00
jack wang 198439e4af [SCSI] libsas: do not set res = 0 in sas_ex_discover_dev()
We should not set res to 0 in function sas_ex_discover_dev  in order to let
it discover it further when wide port hotplug in .

Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-11-06 13:10:42 -06:00
Tom Peng 19252de681 [SCSI] libsas: fix wide port hotplug issues
Hotplug of phys which form wide ports simply does not work at the moment.  Fix
this by adding checks at the hotplug points to see if the attached sas address
of the phy already exists (in which case it's part of a wide port) and act
accordingly.

Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: Kevin Ao <aoqingyun@usish.com>
[jejb: tidied up coding, fixed an error case and made TRUE/FALSE lower
 case to fix a ppc64 compile error in linux-next]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-30 09:54:39 -05:00
Tom Peng 5381837f12 [SCSI] libsas: reuse the original port when hotplugging phys in wide ports
There's a hotplug problem in the way libsas allocates ports: it loops over the
available ports first trying to add to an existing for a wide port and
otherwise allocating the next free port.  This scheme only works if the port
array is packed from zero, which fails if a port gets hot unplugged and the
array becomes sparse.  In that case, a new port is formed even if there's a
wide port it should be part of.  Fix this by creating two loops over all the
ports:  the first to see if the phy should be part of a wide port and the
second to form a new port in an empty port slot.

Signed-off-by: Tom Peng <tom_peng@usish.com>
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-07-16 12:50:44 -05:00
Tejun Heo 5f49f63178 block: set rq->resid_len to blk_rq_bytes() on issue
In commit c3a4d78c58, while introducing
rq->resid_len, the default value of residue count was changed from
full count to zero.  The conversion was done under the assumption that
when a request fails residue count wasn't defined.  However, Boaz and
James pointed out that this wasn't true and the residue count should
be preserved for failed requests too.

This patchset restores the original behavior by setting rq->resid_len
to blk_rq_bytes(rq) on request start and restoring explicit clearing
in affected drivers.  While at it, take advantage of the fact that
rq->resid_len is set to full count where applicable.

* ide-cd: rq->resid_len cleared on pc success

* mptsas: req->resid_len cleared on success

* sas_expander: rsp/req->resid_len cleared on success

* mpt2sas_transport: req->resid_len cleared on success

* ide-cd, ide-tape, mptsas, sas_host_smp, mpt2sas_transport, ub: take
  advantage of initial full count to simplify code

Boaz Harrosh spotted bug in resid_len initialization.  Fixed as
suggested.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-19 11:36:08 +02:00
Tejun Heo b079041030 block: cleanup rq->data_len usages
With recent unification of fields, it's now guaranteed that
rq->data_len always equals blk_rq_bytes().  Convert all non-IDE direct
users to accessors.  IDE will be converted in a separate patch.

Boaz: spotted incorrect data_len/resid_len conversion in osd.

[ Impact: convert direct rq->data_len usages to blk_rq_bytes() ]

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-11 09:50:55 +02:00
Tejun Heo c3a4d78c58 block: add rq->resid_len
rq->data_len served two purposes - the length of data buffer on issue
and the residual count on completion.  This duality creates some
headaches.

First of all, block layer and low level drivers can't really determine
what rq->data_len contains while a request is executing.  It could be
the total request length or it coulde be anything else one of the
lower layers is using to keep track of residual count.  This
complicates things because blk_rq_bytes() and thus
[__]blk_end_request_all() relies on rq->data_len for PC commands.
Drivers which want to report residual count should first cache the
total request length, update rq->data_len and then complete the
request with the cached data length.

Secondly, it makes requests default to reporting full residual count,
ie. reporting that no data transfer occurred.  The residual count is
an exception not the norm; however, the driver should clear
rq->data_len to zero to signify the normal cases while leaving it
alone means no data transfer occurred at all.  This reverse default
behavior complicates code unnecessarily and renders block PC on some
drivers (ide-tape/floppy) unuseable.

This patch adds rq->resid_len which is used only for residual count.

While at it, remove now unnecessasry blk_rq_bytes() caching in
ide_pc_intr() as rq->data_len is not changed anymore.

Boaz	: spotted missing conversion in osd
Sergei	: spotted too early conversion to blk_rq_bytes() in ide-tape

[ Impact: cleanup residual count handling, report 0 resid by default ]

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-11 09:50:53 +02:00
Jeff Garzik 94be9a58d7 [libata] get-identity ioctl: Fix use of invalid memory pointer
for SAS drivers.

Caught by Ke Wei (and team?) at Marvell.

Also, move the ata_scsi_ioctl export to libata-scsi.c, as that seems to be the
general trend.

Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16 10:17:09 -05:00
Roel Kluin a234b1103f [SCSI] libsas: fix test for negative unsigned and typos
unsigned req->data_len cannot be negative, and fix =-/-= typo

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-01-02 12:16:38 -06:00
Kay Sievers 71610f55fa [SCSI] struct device - replace bus_id with dev_name(), dev_set_name()
[jejb: limit ioctl to returning 20 characters to avoid overrun
       on long device names and add a few more conversions]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2009-01-02 10:22:16 -06:00
Linus Torvalds e26feff647 Merge branch 'for-2.6.28' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.28' of git://git.kernel.dk/linux-2.6-block: (132 commits)
  doc/cdrom: Trvial documentation error, file not present
  block_dev: fix kernel-doc in new functions
  block: add some comments around the bio read-write flags
  block: mark bio_split_pool static
  block: Find bio sector offset given idx and offset
  block: gendisk integrity wrapper
  block: Switch blk_integrity_compare from bdev to gendisk
  block: Fix double put in blk_integrity_unregister
  block: Introduce integrity data ownership flag
  block: revert part of d7533ad0e132f92e75c1b2eb7c26387b25a583c1
  bio.h: Remove unused conditional code
  block: remove end_{queued|dequeued}_request()
  block: change elevator to use __blk_end_request()
  gdrom: change to use __blk_end_request()
  memstick: change to use __blk_end_request()
  virtio_blk: change to use __blk_end_request()
  blktrace: use BLKTRACE_BDEV_SIZE as the name size for setup structure
  block: add lld busy state exporting interface
  block: Fix blk_start_queueing() to not kick a stopped queue
  include blktrace_api.h in headers_install
  ...
2008-10-10 10:52:45 -07:00
Jens Axboe 242f9dcb8b block: unify request timeout handling
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.

Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.

Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:13 +02:00
Tejun Heo 82ef04fb4c libata: make SCR access ops per-link
Logically, SCR access ops should take @link; however, there was no
compelling reason to convert all SCR access ops when adding @link
abstraction as there's one-to-one mapping between a port and a non-PMP
link.  However, that assumption won't hold anymore with the scheduled
addition of slave link.

Make SCR access ops per-link.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:22:28 -04:00
Harvey Harrison cadbd4a5e3 [SCSI] replace __FUNCTION__ with __func__
[jejb: fixed up a ton of missed conversions.

 All of you are on notice this has happened, driver trees will now
 need to be rebased]

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: SCSI List <linux-scsi@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-07-27 10:31:49 -04:00