Since the introduction of the vlan_stats_per_port option the netlink
export of it has been broken since I made a typo and used the ifla
attribute instead of the bridge option to retrieve its state.
Sysfs export is fine, only netlink export has been affected.
Fixes: 9163a0fc1f ("net: bridge: add support for per-port vlan stats")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the commit below was introduced it changed two visible things:
- the skb was no longer passed through the protocol handlers with the
original device
- the skb was passed up the stack with skb->dev = bridge
The first change broke af_packet sockets on bridge ports. For example we
use them for hostapd which listens for ETH_P_PAE packets on the ports.
We discussed two possible fixes:
- create a clone and pass it through NF_HOOK(), act on the original skb
based on the result
- somehow signal to the caller from the okfn() that it was called,
meaning the skb is ok to be passed, which this patch is trying to
implement via returning 1 from the bridge link-local okfn()
Note that we rely on the fact that NF_QUEUE/STOLEN would return 0 and
drop/error would return < 0 thus the okfn() is called only when the
return was 1, so we signal to the caller that it was called by preserving
the return value from nf_hook().
Fixes: 8626c56c82 ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_multicast_start_querier() walks over the port list but it can be
called from a timer with only multicast_lock held which doesn't protect
the port list, so use RCU to walk over it.
Fixes: c83b8fab06 ("bridge: Restart queries when last querier expires")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to be careful and always zero the whole br_ip struct when it is
used for matching since the rhashtable change. This patch fixes all the
places which didn't properly clear it which in turn might've caused
mismatches.
Thanks for the great bug report with reproducing steps and bisection.
Steps to reproduce (from the bug report):
ip link add br0 type bridge mcast_querier 1
ip link set br0 up
ip link add v2 type veth peer name v3
ip link set v2 master br0
ip link set v2 up
ip link set v3 up
ip addr add 3.0.0.2/24 dev v3
ip netns add test
ip link add v1 type veth peer name v1 netns test
ip link set v1 master br0
ip link set v1 up
ip -n test link set v1 up
ip -n test addr add 3.0.0.1/24 dev v1
# Multicast receiver
ip netns exec test socat
UDP4-RECVFROM:5588,ip-add-membership=224.224.224.224:3.0.0.1,fork -
# Multicast sender
echo hello | nc -u -s 3.0.0.2 224.224.224.224 5588
Reported-by: liam.mcbirnie@boeing.com
Fixes: 19e3a9c90c ("net: bridge: convert multicast to generic rhashtable")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since Commit 21d1196a35 ("ipv4: set transport header earlier"),
skb->transport_header has been always set before entering INET
netfilter. This patch is to set skb->transport_header for bridge
before entering INET netfilter by bridge-nf-call-iptables.
It also fixes an issue that sctp_error() couldn't compute a right
csum due to unset skb->transport_header.
Fixes: e6d8b64b34 ("net: sctp: fix and consolidate SCTP checksumming code")
Reported-by: Li Shuang <shuali@redhat.com>
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
1) Add .release_ops to properly unroll .select_ops, use it from nft_compat.
After this change, we can remove list of extensions too to simplify this
codebase.
2) Update amanda conntrack helper to support v3.4, from Florian Tham.
3) Get rid of the obsolete BUGPRINT macro in ebtables, from
Florian Westphal.
4) Merge IPv4 and IPv6 masquerading infrastructure into one single module.
From Florian Westphal.
5) Patchset to remove nf_nat_l3proto structure to get rid of
indirections, from Florian Westphal.
6) Skip unnecessary conntrack timeout updates in case the value is
still the same, also from Florian Westphal.
7) Remove unnecessary 'fall through' comments in empty switch cases,
from Li RongQing.
8) Fix lookup to fixed size hashtable sets on big endian with 32-bit keys.
9) Incorrect logic to deactivate path of fixed size hashtable sets,
element was being tested to self.
10) Remove nft_hash_key(), the bitmap set is always selected for 16-bit
keys.
11) Use boolean whenever possible in IPVS codebase, from Andrea Claudi.
12) Enter close state in conntrack if RST matches exact sequence number,
from Florian Westphal.
13) Initialize dst_cache in tunnel extension, from wenxu.
14) Pass protocol as u16 to xt_check_match and xt_check_target, from
Li RongQing.
15) SCTP header is granted to be in a linear area from IPVS NAT handler,
from Xin Long.
16) Don't steal packets coming from slave VRF device from the
ip_sabotage_in() path, from David Ahern.
17) Fix unsafe update of basechain stats, from Li RongQing.
18) Make sure CONNTRACK_LOCKS is power of 2 to let compiler optimize
modulo operation as bitwise AND, from Li RongQing.
19) Use device_attribute instead of internal definition in the IDLETIMER
target, from Sami Tolvanen.
20) Merge redir, masq and IPv4/IPv6 NAT chain types, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup to a173f066c7 ("netfilter: bridge: Don't sabotage nf_hook
calls from an l3mdev"). Some packets (e.g., ndisc) do not have the skb
device flipped to the l3mdev (e.g., VRF) device. Update ip_sabotage_in
to not drop packets for slave devices too. Currently, neighbor
solicitation packets for 'dev -> bridge (addr) -> vrf' setups are getting
dropped. This patch enables IPv6 communications for bridges with an
address that are enslaved to a VRF.
Fixes: 73e20b761a ("net: vrf: Add support for PREROUTING rules on vrf device")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The proto in struct xt_match and struct xt_target is u16, when
calling xt_check_target/match, their proto argument is u8,
and will cause truncation, it is harmless to ip packet, since
ip proto is u8
if a etable's match/target has proto that is u16, will cause
the check failure.
and convert be16 to short in bridge/netfilter/ebtables.c
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Drop switchdev_ops.switchdev_port_attr_set. Drop the uses of this field
from all clients, which were migrated to use switchdev notification in
the previous patches.
Add a new function switchdev_port_attr_notify() that sends the switchdev
notifications SWITCHDEV_PORT_ATTR_SET and calls the blocking (process)
notifier chain.
We have one odd case within net/bridge/br_switchdev.c with the
SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS attribute identifier that
requires executing from atomic context, we deal with that one
specifically.
Drop __switchdev_port_attr_set() and update switchdev_port_attr_set()
likewise.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are however frequently triggered by syzkaller, so remove them.
ebtables userspace should never trigger any of these, so there is little
value in making them pr_debug (or ratelimited).
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 5a2de63fd1 ("bridge: do not add port to router list
when receives query with source 0.0.0.0") and commit 0fe5119e26 ("net:
bridge: remove ipv6 zero address check in mcast queries")
The reason is RFC 4541 is not a standard but suggestive. Currently we
will elect 0.0.0.0 as Querier if there is no ip address configured on
bridge. If we do not add the port which recives query with source
0.0.0.0 to router list, the IGMP reports will not be about to forward
to Querier, IGMP data will also not be able to forward to dest.
As Nikolay suggested, revert this change first and add a boolopt api
to disable none-zero election in future if needed.
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reported-by: Sebastian Gottschall <s.gottschall@newmedia-net.de>
Fixes: 5a2de63fd1 ("bridge: do not add port to router list when receives query with source 0.0.0.0")
Fixes: 0fe5119e26 ("net: bridge: remove ipv6 zero address check in mcast queries")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all switchdev drivers have been converted to check the
SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS flags and report flags that they
do not support accordingly, we can migrate the bridge code to try to set
that attribute first, check the results and then do the actual setting.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_ip4_multicast_mrd_rcv only return 0 and -ENOMSG,
no other negative value
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for you net-next
tree:
1) Missing NFTA_RULE_POSITION_ID netlink attribute validation,
from Phil Sutter.
2) Restrict matching on tunnel metadata to rx/tx path, from wenxu.
3) Avoid indirect calls for IPV6=y, from Florian Westphal.
4) Add two indirections to prepare merger of IPV4 and IPV6 nat
modules, from Florian Westphal.
5) Broken indentation in ctnetlink, from Colin Ian King.
6) Patches to use struct_size() from netfilter and IPVS,
from Gustavo A. R. Silva.
7) Display kernel splat only once in case of racing to confirm
conntrack from bridge plus nfqueue setups, from Chieh-Min Wang.
8) Skip checksum validation for layer 4 protocols that don't need it,
patch from Alin Nastac.
9) Sparse warning due to symbol that should be static in CLUSTERIP,
from Wei Yongjun.
10) Add new toggle to disable SDP payload translation when media
endpoint is reachable though the same interface as the signalling
peer, from Alin Nastac.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some protocols have other means to verify the payload integrity
(AH, ESP, SCTP) while others are incompatible with nf_ip(6)_checksum
implementation because checksum is either optional or might be
partial (UDPLITE, DCCP, GRE). Because nf_ip(6)_checksum was used
to validate the packets, ip(6)tables REJECT rules were not capable
to generate ICMP(v6) errors for the protocols mentioned above.
This commit also fixes the incorrect pseudo-header protocol used
for IPv4 packets that carry other transport protocols than TCP or
UDP (pseudo-header used protocol 0 iso the proper value).
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
size = struct_size(instance, entry, count);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a dedicated NDO for getting a port's parent ID, get rid
of SWITCHDEV_ATTR_ID_PORT_PARENT_ID and convert all callers to use the
NDO exclusively. This is a preliminary change to getting rid of
switchdev_ops eventually.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for getting rid of switchdev_ops, create a dedicated NDO
operation for getting the port's parent identifier. There are
essentially two classes of drivers that need to implement getting the
port's parent ID which are VF/PF drivers with a built-in switch, and
pure switchdev drivers such as mlxsw, ocelot, dsa etc.
We introduce a helper function: dev_get_port_parent_id() which supports
recursion into the lower devices to obtain the first port's parent ID.
Convert the bridge, core and ipv4 multicast routing code to check for
such ndo_get_port_parent_id() and call the helper function when valid
before falling back to switchdev_port_attr_get(). This will allow us to
convert all relevant drivers in one go instead of having to implement
both switchdev_port_attr_get() and ndo_get_port_parent_id() operations,
then get rid of switchdev_port_attr_get().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next tree:
1) Introduce a hashtable to speed up object lookups, from Florian Westphal.
2) Make direct calls to built-in extension, also from Florian.
3) Call helper before confirming the conntrack as it used to be originally,
from Florian.
4) Call request_module() to autoload br_netfilter when physdev is used
to relax the dependency, also from Florian.
5) Allow to insert rules at a given position ID that is internal to the
batch, from Phil Sutter.
6) Several patches to replace conntrack indirections by direct calls,
and to reduce modularization, from Florian. This also includes
several follow up patches to deal with minor fallout from this
rework.
7) Use RCU from conntrack gre helper, from Florian.
8) GRE conntrack module becomes built-in into nf_conntrack, from Florian.
9) Replace nf_ct_invert_tuplepr() by calls to nf_ct_invert_tuple(),
from Florian.
10) Unify sysctl handling at the core of nf_conntrack, from Florian.
11) Provide modparam to register conntrack hooks.
12) Allow to match on the interface kind string, from wenxu.
13) Remove several exported symbols, not required anymore now after
a bit of de-modulatization work has been done, from Florian.
14) Remove built-in map support in the hash extension, this can be
done with the existing userspace infrastructure, from laura.
15) Remove indirection to calculate checksums in IPVS, from Matteo Croce.
16) Use call wrappers for indirection in IPVS, also from Matteo.
17) Remove superfluous __percpu parameter in nft_counter, patch from
Luc Van Oostenryck.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree:
1) The nftnl mutex is now per-netns, therefore use reference counter
for matches and targets to deal with concurrent updates from netns.
Moreover, place extensions in a pernet list. Patches from Florian Westphal.
2) Bail out with EINVAL in case of negative timeouts via setsockopt()
through ip_vs_set_timeout(), from ZhangXiaoxu.
3) Spurious EINVAL on ebtables 32bit binary with 64bit kernel, also
from Florian.
4) Reset TCP option header parser in case of fingerprint mismatch,
otherwise follow up overlapping fingerprint definitions including
TCP options do not work, from Fernando Fernandez Mancera.
5) Compilation warning in ipt_CLUSTER with CONFIG_PROC_FS unset.
From Anders Roxell.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike ip(6)tables ebtables only counts user-defined chains.
The effect is that a 32bit ebtables binary on a 64bit kernel can do
'ebtables -N FOO' only after adding at least one rule, else the request
fails with -EINVAL.
This is a similar fix as done in
3f1e53abff ("netfilter: ebtables: don't attempt to allocate 0-sized compat array").
Fixes: 7d7d7e0211 ("netfilter: compat: reject huge allocation requests")
Reported-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When multiple multicast routers are present in a broadcast domain then
only one of them will be detectable via IGMP/MLD query snooping. The
multicast router with the lowest IP address will become the selected and
active querier while all other multicast routers will then refrain from
sending queries.
To detect such rather silent multicast routers, too, RFC4286
("Multicast Router Discovery") provides a standardized protocol to
detect multicast routers for multicast snooping switches.
This patch implements the necessary MRD Advertisement message parsing
and after successful processing adds such routers to the internal
multicast router list.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Next to snooping IGMP/MLD queries RFC4541, section 2.1.1.a) recommends
to snoop multicast router advertisements to detect multicast routers.
Multicast router advertisements are sent to an "all-snoopers"
multicast address. To be able to receive them reliably, we need to
join this group.
Otherwise other snooping switches might refrain from forwarding these
advertisements to us.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors ip_mc_check_igmp(), ipv6_mc_check_mld() and
their callers (more precisely, the Linux bridge) to not rely on
the skb_trimmed parameter anymore.
An skb with its tail trimmed to the IP packet length was initially
introduced for the following three reasons:
1) To be able to verify the ICMPv6 checksum.
2) To be able to distinguish the version of an IGMP or MLD query.
They are distinguishable only by their size.
3) To avoid parsing data for an IGMPv3 or MLDv2 report that is
beyond the IP packet but still within the skb.
The first case still uses a cloned and potentially trimmed skb to
verfiy. However, there is no need to propagate it to the caller.
For the second and third case explicit IP packet length checks were
added.
This hopefully makes ip_mc_check_igmp() and ipv6_mc_check_mld() easier
to read and verfiy, as well as easier to use.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Externally learned entries can be added by a user or by a switch driver
that is notifying the bridge driver about entries that were learned in
hardware.
In the first case, the entries are not marked with the 'added_by_user'
flag, which causes switch drivers to ignore them and not offload them.
The 'added_by_user' flag can be set on externally learned FDB entries
based on the 'swdev_notify' parameter in br_fdb_external_learn_add(),
which effectively means if the created / updated FDB entry was added by
a user or not.
Fixes: 816a3bed95 ("switchdev: Add fdb.added_by_user to switchdev notifications")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: bridge@lists.linux-foundation.org
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain cases, pskb_trim_rcsum() may change skb pointers.
Reinitialize header pointers afterwards to avoid potential
use-after-frees. Add a note in the documentation of
pskb_trim_rcsum(). Found by KASAN.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following command:
iptables -D FORWARD -m physdev ...
causes connectivity loss in some setups.
Reason is that iptables userspace will probe kernel for the module revision
of the physdev patch, and physdev has an artificial dependency on
br_netfilter (xt_physdev use makes no sense unless a br_netfilter module
is loaded).
This causes the "phydev" module to be loaded, which in turn enables the
"call-iptables" infrastructure.
bridged packets might then get dropped by the iptables ruleset.
The better fix would be to change the "call-iptables" defaults to 0 and
enforce explicit setting to 1, but that breaks backwards compatibility.
This does the next best thing: add a request_module call to checkentry.
This was a stray '-D ... -m physdev' won't activate br_netfilter
anymore.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The skb header should be set to ethernet header before using
is_skb_forwardable. Because the ethernet header length has been
considered in is_skb_forwardable(including dev->hard_header_len
length).
To reproduce the issue:
1, add 2 ports on linux bridge br using following commands:
$ brctl addbr br
$ brctl addif br eth0
$ brctl addif br eth1
2, the MTU of eth0 and eth1 is 1500
3, send a packet(Data 1480, UDP 8, IP 20, Ethernet 14, VLAN 4)
from eth0 to eth1
So the expect result is packet larger than 1500 cannot pass through
eth0 and eth1. But currently, the packet passes through success, it
means eth1's MTU limit doesn't take effect.
Fixes: f6367b4660 ("bridge: use is_skb_forwardable in forward path")
Cc: bridge@lists.linux-foundation.org
Cc: Nkolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will enable vetoing of FDB entries. Make it possible
to communicate details of why an FDB entry is not acceptable back to the
user.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may not be able to support certain FDB entries, and an error
code is insufficient to give clear hints as to the reasons of rejection.
In order to make it possible to communicate the rejection reason, extend
ndo_fdb_add() with an extack argument. Adapt the existing
implementations of ndo_fdb_add() to take the parameter (and ignore it).
Pass the extack parameter when invoking ndo_fdb_add() from rtnl_fdb_add().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
This is the first batch of Netfilter fixes for your net tree:
1) Fix endless loop in nf_tables rules netlink dump, from Phil Sutter.
2) Reference counter leak in object from the error path, from Taehee Yoo.
3) Selective rule dump requires table and chain.
4) Fix DNAT with nft_flow_offload reverse route lookup, from wenxu.
5) Use GFP_KERNEL_ACCOUNT in vmalloc allocation from ebtables, from
Shakeel Butt.
6) Set ifindex from route to fix interaction with VRF slave device,
also from wenxu.
7) Use nfct_help() to check for conntrack helper, IPS_HELPER status
flag is only set from explicit helpers via -j CT, from Henry Yen.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo reported forwarding issues inside the linux bridge,
if the enslaved interfaces use the fq qdisc.
Similar to commit 8203e2d844 ("net: clear skb->tstamp in
forwarding paths"), we need to clear the tstamp field in
the bridge forwarding path.
Fixes: 80b14dee2b ("net: Add a new socket option for a future transmit time.")
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Reported-and-tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The [ip,ip6,arp]_tables use x_tables_info internally and the underlying
memory is already accounted to kmemcg. Do the same for ebtables. The
syzbot, by using setsockopt(EBT_SO_SET_ENTRIES), was able to OOM the
whole system from a restricted memcg, a potential DoS.
By accounting the ebt_table_info, the memory used for ebt_table_info can
be contained within the memcg of the allocating process. However the
lifetime of ebt_table_info is independent of the allocating process and
is tied to the network namespace. So, the oom-killer will not be able to
relieve the memory pressure due to ebt_table_info memory. The memory for
ebt_table_info is allocated through vmalloc. Currently vmalloc does not
handle the oom-killed allocating process correctly and one large
allocation can bypass memcg limit enforcement. So, with this patch,
at least the small allocations will be contained. For large allocations,
we need to fix vmalloc.
Reported-by: syzbot+7713f3aa67be76b1552c@syzkaller.appspotmail.com
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When adding / deleting VLANs to / from a bridge port, the bridge driver
first tries to propagate the information via switchdev and falls back to
the 8021q driver in case the underlying driver does not support
switchdev. This can result in a memory leak [1] when VXLAN and mlxsw
ports are enslaved to the bridge:
$ ip link set dev vxlan0 master br0
# No mlxsw ports are enslaved to 'br0', so mlxsw ignores the switchdev
# notification and the bridge driver adds the VLAN on 'vxlan0' via the
# 8021q driver
$ bridge vlan add vid 10 dev vxlan0 pvid untagged
# mlxsw port is enslaved to the bridge
$ ip link set dev swp1 master br0
# mlxsw processes the switchdev notification and the 8021q driver is
# skipped
$ bridge vlan del vid 10 dev vxlan0
This results in 'struct vlan_info' and 'struct vlan_vid_info' being
leaked, as they were allocated by the 8021q driver during VLAN addition,
but never freed as the 8021q driver was skipped during deletion.
Fix this by introducing a new VLAN private flag that indicates whether
the VLAN was added on the port by switchdev or the 8021q driver. If the
VLAN was added by the 8021q driver, then we make sure to delete it via
the 8021q driver as well.
[1]
unreferenced object 0xffff88822d20b1e8 (size 256):
comm "bridge", pid 2532, jiffies 4295216998 (age 1188.830s)
hex dump (first 32 bytes):
e0 42 97 ce 81 88 ff ff 00 00 00 00 00 00 00 00 .B..............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000f82d851d>] kmem_cache_alloc_trace+0x1be/0x330
[<00000000e0178b02>] vlan_vid_add+0x661/0x920
[<00000000218ebd5f>] __vlan_add+0x1be9/0x3a00
[<000000006eafa1ca>] nbp_vlan_add+0x8b3/0xd90
[<000000003535392c>] br_vlan_info+0x132/0x410
[<00000000aedaa9dc>] br_afspec+0x75c/0x870
[<00000000f5716133>] br_setlink+0x3dc/0x6d0
[<00000000aceca5e2>] rtnl_bridge_setlink+0x615/0xb30
[<00000000a2f2d23e>] rtnetlink_rcv_msg+0x3a3/0xa80
[<0000000064097e69>] netlink_rcv_skb+0x152/0x3c0
[<000000008be8d614>] rtnetlink_rcv+0x21/0x30
[<000000009ab2ca25>] netlink_unicast+0x52f/0x740
[<00000000e7d9ac96>] netlink_sendmsg+0x9c7/0xf50
[<000000005d1e2050>] sock_sendmsg+0xbe/0x120
[<00000000d51426bc>] ___sys_sendmsg+0x778/0x8f0
[<00000000b9d7b2cc>] __sys_sendmsg+0x112/0x270
unreferenced object 0xffff888227454308 (size 32):
comm "bridge", pid 2532, jiffies 4295216998 (age 1188.882s)
hex dump (first 32 bytes):
88 b2 20 2d 82 88 ff ff 88 b2 20 2d 82 88 ff ff .. -...... -....
81 00 0a 00 01 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000f82d851d>] kmem_cache_alloc_trace+0x1be/0x330
[<0000000018050631>] vlan_vid_add+0x3e6/0x920
[<00000000218ebd5f>] __vlan_add+0x1be9/0x3a00
[<000000006eafa1ca>] nbp_vlan_add+0x8b3/0xd90
[<000000003535392c>] br_vlan_info+0x132/0x410
[<00000000aedaa9dc>] br_afspec+0x75c/0x870
[<00000000f5716133>] br_setlink+0x3dc/0x6d0
[<00000000aceca5e2>] rtnl_bridge_setlink+0x615/0xb30
[<00000000a2f2d23e>] rtnetlink_rcv_msg+0x3a3/0xa80
[<0000000064097e69>] netlink_rcv_skb+0x152/0x3c0
[<000000008be8d614>] rtnetlink_rcv+0x21/0x30
[<000000009ab2ca25>] netlink_unicast+0x52f/0x740
[<00000000e7d9ac96>] netlink_sendmsg+0x9c7/0xf50
[<000000005d1e2050>] sock_sendmsg+0xbe/0x120
[<00000000d51426bc>] ___sys_sendmsg+0x778/0x8f0
[<00000000b9d7b2cc>] __sys_sendmsg+0x112/0x270
Fixes: d70e42b22d ("mlxsw: spectrum: Enable VxLAN enslavement to VLAN-aware bridges")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: bridge@lists.linux-foundation.org
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling DNAT'ed packets on a bridge device, the neighbour cache entry
from lookup was used without checking its state. It means that a cache entry
in the NUD_STALE state will be used directly instead of entering the NUD_DELAY
state to confirm the reachability of the neighbor.
This problem becomes worse after commit 2724680bce ("neigh: Keep neighbour
cache entries if number of them is small enough."), since all neighbour cache
entries in the NUD_STALE state will be kept in the neighbour table as long as
the number of cache entries does not exceed the value specified in gc_thresh1.
This commit validates the state of a neighbour cache entry before using
the entry.
Signed-off-by: JianJhen Chen <kchen@synology.com>
Reviewed-by: JinLin Chen <jlchen@synology.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts the bridge netfilter (calling iptables hooks from bridge)
facility to use the extension infrastructure.
The bridge_nf specific hooks in skb clone and free paths are removed, they
have been replaced by the skb_ext hooks that do the same as the bridge nf
allocations hooks did.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pointer is going to be removed soon, so use the existing helpers in
more places to avoid noise when the removal happens.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
function br_multicast_toggle now always return 0,
so the variable 'err' is unneeded.
Also cleanup dead branch in br_changelink.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements ndo_fdb_get for the bridge
fdb.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port device seeks approval of a potential new MAC address, make
sure that should the bridge device end up using this address, all
interested parties would agree with it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is attached to a bridge, the address of the bridge in
question may change as well. Even if it would not change at this
point (because the current bridge address is lower), it might end up
changing later as a result of detach of another port, which can't be
vetoed.
Therefore issue NETDEV_PRE_CHANGEADDR regardless of whether the address
will be used at this point or not, and make sure all involved parties
would agree with the change.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch, bridge driver has extack argument available to
pass to switchdev. Therefore extend switchdev_port_obj_add() with this
argument, updating all callers, and passing the argument through to
switchdev_port_obj_notify().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_bridge_setlink has been updated in the previous patch to have extack
available, and changelink RTNL op has had this argument since the time
extack was added. Propagate both through the bridge driver to eventually
reach br_switchdev_port_vlan_add(), where it will be used by subsequent
patches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers may not be able to implement a VLAN addition or reconfiguration.
In those cases it's desirable to explain to the user that it was
rejected (and why).
To that end, add extack argument to ndo_bridge_setlink. Adapt all users
to that change.
Following patches will use the new argument in the bridge driver.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a driver unoffloads all FDB entries en bloc, it's inefficient to
send the switchdev notification one by one. Add a helper that unsets the
offload flag on FDB entries on a given bridge port and VLAN.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov
Xin Long
David S. Miller
David Ahern
Li RongQing
Florian Fainelli
Florian Westphal
Hangbin Liu
Alin Nastac
Gustavo A. R. Silva
YueHaibing
Linus Lüssing
Ido Schimmel
Ross Lagerwall
Yunjian Wang
Petr Machata
Paolo Abeni
Shakeel Butt
JianJhen Chen
Roopa Prabhu