[ Upstream commit bcd8a45223 ]
Executing driver on servers with more than 32 CPUs were faced with command
timeouts. This is because we were not geting completions for commands
submitted on IQ32 - IQ63.
Set E64Q bit to enable upper inbound and outbound queues 32 to 63 in the
MPI main configuration table.
Added 500ms delay after successful MPI initialization as mentioned in
controller datasheet.
Link: https://lore.kernel.org/r/20220411064603.668448-3-Ajish.Koshy@microchip.com
Fixes: 05c6c029a4 ("scsi: pm80xx: Increase number of supported queues")
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 294080eacf ]
When upper inbound and outbound queues 32-63 are enabled, we see upper
vectors 32-63 in interrupt service routine. We need corresponding registers
to handle masking and unmasking of these upper interrupts.
To achieve this, we use registers MSGU_ODMR_U(0x34) to mask and
MSGU_ODMR_CLR_U(0x3C) to unmask the interrupts. In these registers bit 0-31
represents interrupt vectors 32-63.
Link: https://lore.kernel.org/r/20220411064603.668448-2-Ajish.Koshy@microchip.com
Fixes: 05c6c029a4 ("scsi: pm80xx: Increase number of supported queues")
Reviewed-by: John Garry <john.garry@huawei.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f792a3629f ]
In pm8001_chip_fw_flash_update_build(), if
pm8001_chip_fw_flash_update_build() fails, the struct fw_control_ex
allocated must be freed.
Link: https://lore.kernel.org/r/20220220031810.738362-23-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c8f04b190 ]
In pm8001_chip_set_dev_state_req(), pm8001_chip_fw_flash_update_req(),
pm80xx_chip_phy_ctl_req() and pm8001_chip_reg_dev_req() add missing calls
to pm8001_tag_free() to free the allocated tag when pm8001_mpi_build_cmd()
fails.
Similarly, in pm8001_exec_internal_task_abort(), if the chip ->task_abort
method fails, the tag allocated for the abort request task must be
freed. Add the missing call to pm8001_tag_free().
Link: https://lore.kernel.org/r/20220220031810.738362-22-damien.lemoal@opensource.wdc.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f90a74892f ]
In pm8001_send_abort_all(), make sure to free the allocated sas task
if pm8001_tag_alloc() or pm8001_mpi_build_cmd() fail.
Link: https://lore.kernel.org/r/20220220031810.738362-21-damien.lemoal@opensource.wdc.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e6b7e740a ]
The call to pm8001_ccb_task_free() at the end of
pm8001_mpi_task_abort_resp() already frees the ccb tag. So when the device
NCQ_ABORT_ALL_FLAG is set, the tag should not be freed again. Also change
the hardcoded 0xBFFFFFFF value to ~NCQ_ABORT_ALL_FLAG as it ought to be.
Link: https://lore.kernel.org/r/20220220031810.738362-19-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3762d8f6ed ]
The declaration of the local variable destination1 in pm80xx_pci_mem_copy()
as a pointer to a u32 results in the sparse warning:
warning: incorrect type in assignment (different base types)
expected unsigned int [usertype]
got restricted __le32 [usertype]
Furthermore, the destination" argument of pm80xx_pci_mem_copy() is wrongly
declared with the const attribute.
Fix both problems by changing the type of the "destination" argument to
"__le32 *" and use this argument directly inside the pm80xx_pci_mem_copy()
function, thus removing the need for the destination1 local variable.
Link: https://lore.kernel.org/r/20220220031810.738362-6-damien.lemoal@opensource.wdc.com
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d6736c3e1 ]
NCQ NON DATA is an NCQ command with the DMA_NONE DMA direction and so a
register-device-to-host-FIS response is expected for it.
However, for an IO_SUCCESS case, mpi_sata_completion() expects a
set-device-bits-FIS for any ata task with an use_ncq field true, which
includes NCQ NON DATA commands.
Fix this to correctly treat NCQ NON DATA commands as non-data by also
testing for the DMA_NONE DMA direction.
Link: https://lore.kernel.org/r/20220220031810.738362-16-damien.lemoal@opensource.wdc.com
Fixes: dbf9bfe615 ("[SCSI] pm8001: add SAS/SATA HBA driver")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa028141ab ]
In the pm8001_chip_sata_req() and pm80xx_chip_sata_req() functions, all
tasks with a DMA direction of DMA_NONE (no data transfer) are initialized
using the ATAP value 0x04. However, NCQ NON DATA commands, while being
DMA_NONE commands are NCQ commands and need to be initialized using the
value 0x07 for ATAP, similarly to other NCQ commands.
Make sure that NCQ NON DATA command tasks are initialized similarly to
other NCQ commands by also testing the task "use_ncq" field in addition to
the DMA direction. While at it, reorganize the code into a chain of if -
else if - else to avoid useless affectations and debug messages.
Link: https://lore.kernel.org/r/20220220031810.738362-15-damien.lemoal@opensource.wdc.com
Fixes: dbf9bfe615 ("[SCSI] pm8001: add SAS/SATA HBA driver")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd6d0e3762 ]
Make sure that the __le32 fields of struct sata_cmd are manipulated after
applying the correct endian conversion. That is, use cpu_to_le32() for
assigning values and le32_to_cpu() for consulting a field value. In
particular, make sure that the calculations for the 4G boundary check are
done using CPU endianness and *not* little endian values. With these fixes,
many sparse warnings are removed.
While at it, fix some code identation and add blank lines after variable
declarations and in some other places to make this code more readable.
Link: https://lore.kernel.org/r/20220220031810.738362-12-damien.lemoal@opensource.wdc.com
Fixes: 0ecdf00ba6 ("[SCSI] pm80xx: 4G boundary fix.")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 970404cc57 ]
Make sure that the __le32 fields of struct ssp_ini_io_start_req are
manipulated after applying the correct endian conversion. That is, use
cpu_to_le32() for assigning values and le32_to_cpu() for consulting a field
value. In particular, make sure that the calculations for the 4G boundary
check are done using CPU endianness and *not* little endian values. With
these fixes, many sparse warnings are removed.
While at it, add blank lines after variable declarations and in some other
places to make this code more readable.
Link: https://lore.kernel.org/r/20220220031810.738362-11-damien.lemoal@opensource.wdc.com
Fixes: 0ecdf00ba6 ("[SCSI] pm80xx: 4G boundary fix.")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f8b12dfb47 ]
All fields of the kek_mgmt_req structure have the type __le32. So make sure
to use cpu_to_le32() to initialize them. This suppresses the sparse
warning:
warning: incorrect type in assignment (different base types)
expected restricted __le32 [addressable] [assigned] [usertype] new_curidx_ksop
got int
Link: https://lore.kernel.org/r/20220220031810.738362-10-damien.lemoal@opensource.wdc.com
Fixes: f5860992db ("[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca374f5d92 ]
All fields of the SASProtocolTimerConfig structure have the __le32 type.
As such, use cpu_to_le32() to initialize them. This change suppresses many
sparse warnings:
warning: incorrect type in assignment (different base types)
expected restricted __le32 [addressable] [usertype] pageCode
got int
Note that the check to limit the value of the STP_IDLE_TMO field is removed
as this field is initialized using the fixed (and small) value defined by
the STP_IDLE_TIME macro.
The pm8001_dbg() calls printing the values of the SASProtocolTimerConfig
structure fileds are changed to use le32_to_cpu() to present the values in
human readable form.
Link: https://lore.kernel.org/r/20220220031810.738362-9-damien.lemoal@opensource.wdc.com
Fixes: a6cb3d012b ("[SCSI] pm80xx: thermal, sas controller config and error handling update")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb225b12db ]
The fields of the set_ctrl_cfg_req structure have the __le32 type, so use
cpu_to_le32() to assign them. This removes the sparse warnings:
warning: incorrect type in assignment (different base types)
expected restricted __le32
got unsigned int
Link: https://lore.kernel.org/r/20220220031810.738362-8-damien.lemoal@opensource.wdc.com
Fixes: 842784e0d1 ("pm80xx: Update For Thermal Page Code")
Fixes: f5860992db ("[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files")
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd2268a180 ]
The ds_ads_m field of struct ssp_ini_tm_start_req has the type __le32.
Assigning a value to it should thus use cpu_to_le32(). This fixes the
sparse warning:
warning: incorrect type in assignment (different base types)
expected restricted __le32 [addressable] [assigned] [usertype] ds_ads_m
got int
Link: https://lore.kernel.org/r/20220220031810.738362-7-damien.lemoal@opensource.wdc.com
Fixes: dbf9bfe615 ("[SCSI] pm8001: add SAS/SATA HBA driver")
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a37b6738b ]
Since the sata_cmd struct is zeroed out before its fields are initialized,
there is no need for using "|=" to initialize the ncqtag_atap_dir_m
field. Using a standard assignment removes the sparse warning:
warning: invalid assignment: |=
Also, since the ncqtag_atap_dir_m field has type __le32, use cpu_to_le32()
to generate the assigned value.
Link: https://lore.kernel.org/r/20220220031810.738362-5-damien.lemoal@opensource.wdc.com
Fixes: c6b9ef5779 ("[SCSI] pm80xx: NCQ error handling changes")
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df7abcaa12 ]
Currently a use-after-free may occur if a sas_task is aborted by the upper
layer before we handle the I/O completion in mpi_ssp_completion() or
mpi_sata_completion().
In this case, the following are the two steps in handling those I/O
completions:
- Call complete() to inform the upper layer handler of completion of
the I/O.
- Release driver resources associated with the sas_task in
pm8001_ccb_task_free() call.
When complete() is called, the upper layer may free the sas_task. As such,
we should not touch the associated sas_task afterwards, but we do so in the
pm8001_ccb_task_free() call.
Fix by swapping the complete() and pm8001_ccb_task_free() calls ordering.
Link: https://lore.kernel.org/r/1643289172-165636-4-git-send-email-john.garry@huawei.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61f162aa43 ]
Currently a use-after-free may occur if a TMF sas_task is aborted before we
handle the IO completion in mpi_ssp_completion(). The abort occurs due to
timeout.
When the timeout occurs, the SAS_TASK_STATE_ABORTED flag is set and the
sas_task is freed in pm8001_exec_internal_tmf_task().
However, if the I/O completion occurs later, the I/O completion still
thinks that the sas_task is available. Fix this by clearing the ccb->task
if the TMF times out - the I/O completion handler does nothing if this
pointer is cleared.
Link: https://lore.kernel.org/r/1643289172-165636-3-git-send-email-john.garry@huawei.com
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c26b85ea16 ]
Current code handles completions for SATA devices in mpi_sata_completion()
and mpi_sata_event().
However, at the time when any SATA event happens, for almost all the event
types, the command is still in the target. It is therefore incorrect to
complete the task in sata_event().
There are some events for which we get sata_completions, some need recovery
procedure and others abort. All the tasks must be completed via
sata_completion() path.
Removed the task done related code from sata_events(). For tasks where we
don't get completions, let top layer call abort() to abort the command post
timeout.
Link: https://lore.kernel.org/r/20220124082255.86223-1-Ajish.Koshy@microchip.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Co-developed-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62afb379a0 ]
According to the comment in check_fw_ready() we should not check the
IOP1_READY field in register SCRATCH_PAD_1 for 8008 or 8009 controllers.
However we check this very field in process_oq() for processing the highest
index interrupt vector. The highest interrupt vector is checked as the FW
is programmed to signal fatal errors through this irq.
Change that function to not check IOP1_READY for those mentioned
controllers, but do check ILA_READY in both cases.
The reason I assume that this was not hit earlier was because we always
allocated 64 MSI(X), and just did not pass the vector index check in
process_oq(), i.e. the handler never ran for vector index 63.
Link: https://lore.kernel.org/r/1642508105-95432-1-git-send-email-john.garry@huawei.com
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 606c54ae97 ]
Starting from commit 05c6c029a4 ("scsi: pm80xx: Increase number of
supported queues") driver initializes only max_q_num queues. Do not use an
invalid queue if the WARN_ON condition is true.
Link: https://lore.kernel.org/r/20211101232825.2350233-4-ipylypiv@google.com
Fixes: 7640e1eb8c ("scsi: pm80xx: Make mpi_build_cmd locking consistent")
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6539262057 upstream.
Calling scsi_remove_host() before scsi_add_host() results in a crash:
BUG: kernel NULL pointer dereference, address: 0000000000000108
RIP: 0010:device_del+0x63/0x440
Call Trace:
device_unregister+0x17/0x60
scsi_remove_host+0xee/0x2a0
pm8001_pci_probe+0x6ef/0x1b90 [pm80xx]
local_pci_probe+0x3f/0x90
We cannot call scsi_remove_host() in pm8001_alloc() because scsi_add_host()
has not been called yet at that point in time.
Function call tree:
pm8001_pci_probe()
|
`- pm8001_pci_alloc()
| |
| `- pm8001_alloc()
| |
| `- scsi_remove_host()
|
`- scsi_add_host()
Link: https://lore.kernel.org/r/20211201041627.1592487-1-ipylypiv@google.com
Fixes: 05c6c029a4 ("scsi: pm80xx: Increase number of supported queues")
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 51e6ed83bb ]
Driver failed to release all memory allocated. This would lead to memory
leak during driver removal.
Properly free memory when the module is removed.
Link: https://lore.kernel.org/r/20210906170404.5682-5-Ajish.Koshy@microchip.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4084a7235d ]
pm8001_mpi_get_nvmd_resp() handles a GET_NVMD_DATA response, not a
SET_NVMD_DATA response, as the log statement implies.
Fixes: 1f889b5871 ("scsi: pm80xx: Fix pm8001_mpi_get_nvmd_resp() race condition")
Link: https://lore.kernel.org/r/20210929025847.646999-1-ipylypiv@google.com
Reviewed-by: Changyuan Lyu <changyuanl@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b27a40534e ]
Commit 1f02beff22 ("scsi: pm80xx: Remove global lock from outbound queue
processing") introduced a lock per outbound queue. Prior to that change the
driver was using a global lock for all outbound queues.
While processing the I/O responses and events the driver takes the outbound
queue spinlock and is supposed to release it in pm8001_ccb_task_free_done()
before calling command done(). Since the older code was using a global
lock, pm8001_ccb_task_free_done() was releasing the global spin lock. The
change that split the lock per outbound queue did not consider this and
pm8001_ccb_task_free_done() was still releasing the global lock.
Link: https://lore.kernel.org/r/20210906170404.5682-3-Ajish.Koshy@microchip.com
Fixes: 1f02beff22 ("scsi: pm80xx: Remove global lock from outbound queue processing")
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Ajish Koshy <Ajish.Koshy@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The variable 'rv' is being initialized with a value that is never read, it
is being updated later on. The assignment is redundant and can be removed.
Link: https://lore.kernel.org/r/20210804143319.115340-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unused value")
The TMF timeout timer may trigger at the same time when the response from a
controller is being handled. When this happens the SAS task may get freed
before the response processing is finished.
Fix this by calling complete() only when SAS_TASK_STATE_DONE is not set.
A similar race condition was fixed in commit b90cd6f2b9 ("scsi: libsas:
fix a race condition when smp task timeout")
Link: https://lore.kernel.org/r/20210707185945.35559-1-ipylypiv@google.com
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix kernel-doc warnings then test again, wash, rinse, find more, then
repeat more/again.
Also fix spellos, some grammar, and some punctuation.
../drivers/scsi/pm8001/pm8001_ctl.c:557: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
** pm8001_ctl_fatal_log_show - fatal error logging
../drivers/scsi/pm8001/pm8001_ctl.c:577: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
** non_fatal_log_show - non fatal error logging
../drivers/scsi/pm8001/pm8001_ctl.c:622: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
** pm8001_ctl_gsm_log_show - gsm dump collection
Link: https://lore.kernel.org/r/20210708165723.8594-1-rdunlap@infradead.org
Cc: Jack Wang <jinpu.wang@cloud.ionos.com>
Cc: linux-scsi@vger.kernel.org
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is a set of minor fixes and clean ups in the core and various
drivers. The only core change in behaviour is the I/O retry for
spinup notify, but that shouldn't impact anything other than the
failing case.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYOqWWyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYBtAQCpqVdl
Axi1SpD6/UuKOgRmboWscoKD8FLHwvLDMRyCRQEAnLu3XdB9HcQrwZOkTG14vrfB
q2XB5cP4XAITxFLN1qo=
=9AO9
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is a set of minor fixes and clean ups in the core and various
drivers.
The only core change in behaviour is the I/O retry for spinup notify,
but that shouldn't impact anything other than the failing case"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (23 commits)
scsi: virtio_scsi: Add validation for residual bytes from response
scsi: ipr: System crashes when seeing type 20 error
scsi: core: Retry I/O for Notify (Enable Spinup) Required error
scsi: mpi3mr: Fix warnings reported by smatch
scsi: qedf: Add check to synchronize abort and flush
scsi: MAINTAINERS: Add mpi3mr driver maintainers
scsi: libfc: Fix array index out of bound exception
scsi: mvsas: Use DEVICE_ATTR_RO()/RW() macro
scsi: megaraid_mbox: Use DEVICE_ATTR_ADMIN_RO() macro
scsi: qedf: Use DEVICE_ATTR_RO() macro
scsi: qedi: Use DEVICE_ATTR_RO() macro
scsi: message: mptfc: Switch from pci_ to dma_ API
scsi: be2iscsi: Fix some missing space in some messages
scsi: be2iscsi: Fix an error handling path in beiscsi_dev_probe()
scsi: ufs: Fix build warning without CONFIG_PM
scsi: bnx2fc: Remove meaningless bnx2fc_abts_cleanup() return value assignment
scsi: qla2xxx: Add heartbeat check
scsi: virtio_scsi: Do not overwrite SCSI status
scsi: libsas: Add LUN number check in .slave_alloc callback
scsi: core: Inline scsi_mq_alloc_queue()
...
This series consists of the usual driver updates (ufs, ibmvfc,
megaraid_sas, lpfc, elx, mpi3mr, qedi, iscsi, storvsc, mpt3sas) with
elx and mpi3mr being new drivers. The major core change is a rework
to drop the status byte handling macros and the old bit shifted
definitions and the rest of the updates are minor fixes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYN7I6iYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishXpRAQCkngYZ
35yQrqOxgOk2pfrysE95tHrV1MfJm2U49NFTwAEAuZutEvBUTfBF+sbcJ06r6q7i
H0hkJN/Io7enFs5v3WA=
=zwIa
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series consists of the usual driver updates (ufs, ibmvfc,
megaraid_sas, lpfc, elx, mpi3mr, qedi, iscsi, storvsc, mpt3sas) with
elx and mpi3mr being new drivers.
The major core change is a rework to drop the status byte handling
macros and the old bit shifted definitions and the rest of the updates
are minor fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (287 commits)
scsi: aha1740: Avoid over-read of sense buffer
scsi: arcmsr: Avoid over-read of sense buffer
scsi: ips: Avoid over-read of sense buffer
scsi: ufs: ufs-mediatek: Add missing of_node_put() in ufs_mtk_probe()
scsi: elx: libefc: Fix IRQ restore in efc_domain_dispatch_frame()
scsi: elx: libefc: Fix less than zero comparison of a unsigned int
scsi: elx: efct: Fix pointer error checking in debugfs init
scsi: elx: efct: Fix is_originator return code type
scsi: elx: efct: Fix link error for _bad_cmpxchg
scsi: elx: efct: Eliminate unnecessary boolean check in efct_hw_command_cancel()
scsi: elx: efct: Do not use id uninitialized in efct_lio_setup_session()
scsi: elx: efct: Fix error handling in efct_hw_init()
scsi: elx: efct: Remove redundant initialization of variable lun
scsi: elx: efct: Fix spelling mistake "Unexected" -> "Unexpected"
scsi: lpfc: Fix build error in lpfc_scsi.c
scsi: target: iscsi: Remove redundant continue statement
scsi: qla4xxx: Remove redundant continue statement
scsi: ppa: Switch to use module_parport_driver()
scsi: imm: Switch to use module_parport_driver()
scsi: mpt3sas: Fix error return value in _scsih_expander_add()
...
Offlining a SATA device connected to a hisi SAS controller and then
scanning the host will result in detecting 255 non-existent devices:
# lsscsi
[2:0:0:0] disk ATA Samsung SSD 860 2B6Q /dev/sda
[2:0:1:0] disk ATA WDC WD2003FYYS-3 1D01 /dev/sdb
[2:0:2:0] disk SEAGATE ST600MM0006 B001 /dev/sdc
# echo "offline" > /sys/block/sdb/device/state
# echo "- - -" > /sys/class/scsi_host/host2/scan
# lsscsi
[2:0:0:0] disk ATA Samsung SSD 860 2B6Q /dev/sda
[2:0:1:0] disk ATA WDC WD2003FYYS-3 1D01 /dev/sdb
[2:0:1:1] disk ATA WDC WD2003FYYS-3 1D01 /dev/sdh
...
[2:0:1:255] disk ATA WDC WD2003FYYS-3 1D01 /dev/sdjb
After a REPORT LUN command issued to the offline device fails, the SCSI
midlayer tries to do a sequential scan of all devices whose LUN number is
not 0. However, SATA does not support LUN numbers at all.
Introduce a generic sas_slave_alloc() handler which will return -ENXIO for
SATA devices if the requested LUN number is larger than 0 and make libsas
drivers use this function as their .slave_alloc callback.
Link: https://lore.kernel.org/r/20210622034037.1467088-1-yuyufen@huawei.com
Reported-by: Wu Bo <wubo40@huawei.com>
Suggested-by: John Garry <john.garry@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Also change the return error code from "-1" to "-ENOMEM".
Link: https://lore.kernel.org/r/20210610094605.16672-2-thunder.leizhen@huawei.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch prepares for converting SAM status codes into an enum. Without
this patch converting SAM status codes into an enumeration type would
trigger complaints about enum type mismatches for the SAS code.
Link: https://lore.kernel.org/r/20210524025457.11299-2-bvanassche@acm.org
Cc: Hannes Reinecke <hare@suse.com>
Cc: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Cc: Jason Yan <yanaijie@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driver is loaded after rmmod some drives are not showing up during
discovery.
SATA drives are directly attached to the controller connected phys. During
device discovery, the IDENTIFY command (qc timeout (cmd 0xec)) is timing out
during revalidation. This will trigger abort from host side and controller
successfully aborts the command and returns success. Post this successful
abort response ATA library decides to mark the disk as NODEV.
To overcome this, inside pm8001_scan_start() after phy_start() call, add get
start response and wait for few milliseconds to trigger next phy start.
This millisecond delay will give sufficient time for the controller state
machine to accept next phy start.
Link: https://lore.kernel.org/r/20210505120103.24497-1-ajish.koshy@microchip.com
Signed-off-by: Ajish Koshy <ajish.koshy@microchip.com>
Signed-off-by: Viswas G <viswas.g@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce spin lock for outbound queue. With this, driver need not acquire
HBA global lock for outbound queue processing.
Link: https://lore.kernel.org/r/20210415103352.3580-9-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Ashokkumar N <Ashokkumar.N@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Producer index(PI) outbound queue and consumer index(CI) for Outbound queue
are in DMA memory. During resume(), the stale PI and CI Values will lead to
unexpected behavior. These values should be reset to 0 during driver
reinitialization.
Link: https://lore.kernel.org/r/20210415103352.3580-8-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Ashokkumar N <Ashokkumar.N@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When controller runs into fatal error, I/Os get stuck with no response,
handler event is defined to complete the pending I/Os (SAS task and
internal task) and also perform the cleanup for the drives.
Link: https://lore.kernel.org/r/20210415103352.3580-7-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ashokkumar N <Ashokkumar.N@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A new sysfs variable 'ctl_iop1_count' is being introduced that tells if
the controller is alive by indicating controller ticks. If on subsequent
run we see the ticks changing that indicates that controller is not
dead.
Using the 'ctl_iop1_count' sysfs variable we can see ticks incrementing:
linux-9saw:~# cat /sys/class/scsi_host/host*/ctl_iop1_count
0x00000069
0x0000006b
0x0000006d
0x00000072
Link: https://lore.kernel.org/r/20210415103352.3580-6-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Vishakha Channapattan <vishakhavc@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Ashokkumar N <Ashokkumar.N@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A new sysfs variable 'ctl_iop0_count' is being introduced that tells if
the controller is alive by indicating controller ticks. If on subsequent
run we see the ticks changing that indicates that controller is not
dead.
Using the 'ctl_iop0_count' sysfs variable we can see ticks incrementing:
linux-9saw:~# cat /sys/class/scsi_host/host*/ctl_iop0_count
0x000000a3
0x000001db
0x000001e4
0x000001e7
Link: https://lore.kernel.org/r/20210415103352.3580-5-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Vishakha Channapattan <vishakhavc@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Ashokkumar N <Ashokkumar.N@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A new sysfs variable 'ctl_raae_count' is being introduced that tells if the
controller is alive by indicating controller ticks. If on subsequent run we
see the ticks changing in RAAE count that indicates that controller is not
dead.
Using the 'ctl_raae_count' sysfs variable we can see ticks incrementing:
linux-9saw:~# cat /sys/class/scsi_host/host*/ctl_raae_count
0x00002245
0x00002253
0x0000225e
Link: https://lore.kernel.org/r/20210415103352.3580-4-Viswas.G@microchip.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Vishakha Channapattan <vishakhavc@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Ashokkumar N <Ashokkumar.N@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A new sysfs variable 'ctl_hmi_error' is being introduced to give the error
details if the MPI initialization fails
Using the 'ctl_hmi_error' sysfs variable we can check the error details:
linux-2dq0:~# cat /sys/class/scsi_host/host*/ctl_hmi_error
0x00000000
0x00000000
0x00000000
Link: https://lore.kernel.org/r/20210415103352.3580-3-Viswas.G@microchip.com
Signed-off-by: Vishakha Channapattan <vishakhavc@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A new sysfs variable 'ctl_mpi_state' is being introduced to check the state
of MPI.
Using the 'ctl_mpi_state' sysfs variable we can check the MPI state:
linux-2dq0:~# cat /sys/class/scsi_host/host*/ctl_mpi_state
MPI is successfully initialized
Link: https://lore.kernel.org/r/20210415103352.3580-2-Viswas.G@microchip.com
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vishakha Channapattan <vishakhavc@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Ashokkumar N <Ashokkumar.N@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
checkpatch reports the following:
ERROR: that open brace { should be on the previous line
+static struct error_fw flash_error_table[] =
+{
Fix a couple of instances of misplaced open bracket.
Link: https://lore.kernel.org/r/1617886593-36421-3-git-send-email-luojiaxing@huawei.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: Jianqin Xie <xiejianqin@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
checkpatch reports the following:
ERROR: space prohibited before that ',' (ctx:WxW)
+int pm8001_mpi_general_event(struct pm8001_hba_info *pm8001_ha , void *piomb);
Remove unnecessary whitespace.
Link: https://lore.kernel.org/r/1617886593-36421-2-git-send-email-luojiaxing@huawei.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: Jianqin Xie <xiejianqin@hisilicon.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The for-loop iterates with a u8 loop counter i and compares this with the
loop upper limit of pm8001_ha->max_q_num which is a u32 type. There is a
potential infinite loop if pm8001_ha->max_q_num is larger than the u8 loop
counter. Fix this by making the loop counter the same type as
pm8001_ha->max_q_num.
[mkp: this is purely theoretical, max_q_num is currently limited to 64]
Link: https://lore.kernel.org/r/20210407135840.494747-1-colin.king@canonical.com
Fixes: 65df7d1986 ("scsi: pm80xx: Fix chip initialization failure")
Addresses-Coverity: ("Infinite loop")
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
mpi_uninit_check() is not being called in an atomic context. The only
caller of mpi_uninit_check() is pm80xx_chip_soft_rst().
Callers of pm80xx_chip_soft_rst():
- pm8001_ioctl_soft_reset()
- pm8001_pci_probe()
- pm8001_pci_remove()
- pm8001_pci_suspend()
- pm8001_pci_resume()
There was a similar fix for mpi_init_check() in commit
d71023af4b ("scsi: pm80xx: Do not busy wait in MPI init check")
Link: https://lore.kernel.org/r/20210406180534.1924345-3-ipylypiv@google.com
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The mpi_uninit_check() takes longer for inbound doorbell register to be
cleared. Increase the timeout substantially so that the driver does not
fail to load.
Previously, the inbound doorbell wait time was mistakenly increased in the
mpi_init_check() instead of mpi_uninit_check(). It is okay to leave the
mpi_init_check() wait time as-is as these are timeout values and if there
is a failure, waiting longer is not an issue.
Link: https://lore.kernel.org/r/20210406180534.1924345-2-ipylypiv@google.com
Fixes: e90e236250 ("scsi: pm80xx: Increase timeout for pm80xx mpi_uninit_check")
Reviewed-by: Vishakha Channapattan <vishakhavc@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Resolve a couple of conflicts between the 5.12 fixes branch and the
5.13 staging tree (iSCSI target and UFS).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ajish Koshy
Damien Le Moal
John Garry
Igor Pylypiv
Martin K. Petersen
Colin Ian King
Randy Dunlap
Linus Torvalds
Yufen Yu
Zhen Lei
Bart Van Assche
Viswas G
Ruksar Devadi
Vishakha Channapattan
Luo Jiaxing