_regmap_raw_write() contains code to call regcache_write() to write
values to the cache. That code calls memcpy() to copy the value data to
the start of the work_buf. However, at least when _regmap_raw_write() is
called from _regmap_bus_raw_write(), the value data is in the work_buf,
and this memcpy() operation may over-write part of that value data,
depending on the value of reg_bytes + pad_bytes. At least when using
reg_bytes==1 and pad_bytes==0, corruption of the value data does occur.
To solve this, remove the memcpy() operation, and modify the subsequent
.parse_val() call to parse the original value buffer directly.
At least in the case of 8-bit register address and 16-bit values, and
writes of single registers at a time, this memcpy-then-parse combination
used to cancel each-other out; for a work-buffer containing xx 89 03,
the memcpy changed it to 89 03 03, and the parse_val changed it back to
89 89 03, thus leaving the value uncorrupted. This appears completely
accidental though. Since commit 8a819ff "regmap: core: Split out in
place value parsing", .parse_val only returns the parsed value, and does
not modify the buffer, and hence does not (accidentally) undo the
corruption caused by memcpy(). This caused bogus values to get written
to HW, thus preventing e.g. audio playback on systems with a WM8903
CODEC. This patch fixes that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This reverts commit bc8ce4 (regmap: don't corrupt work buffer in
_regmap_raw_write()) since it turns out that it can cause issues when
taken in isolation from the other changes in -next that lead to its
discovery. On the basis that nobody noticed the problems for quite some
time without that subsequent work let's drop it from v3.9.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix format specifier in dev_dbg and suppress the following warning
drivers/base/regmap/regcache.c: In function
‘regcache_sync_block_raw_flush’:
drivers/base/regmap/regcache.c:593:2: warning: format ‘%d’ expects
argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regcache_sync_block_raw is used only in this file. Hence make it static.
Silences the following warning:
drivers/base/regmap/regcache.c:608:5: warning:
symbol 'regcache_sync_block_raw' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When syncing blocks of data using raw writes combine the writes into a
single block write, saving us bus overhead for setup, addressing and
teardown.
Currently the block write is done unconditionally as it is expected that
hardware which has a register format which can support raw writes will
support auto incrementing writes, this decision may need to be revised in
future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
For code clarity after implementing block writes split out the raw and
non-raw I/O sync implementations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
The idea of holding blocks of registers in device format is shared between
at least rbtree and lzo cache formats so split out the loop that does the
sync from the rbtree code so optimisations on it can be reused.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
The idea of maintaining a bitmap of present registers is something that
can usefully be used by other cache types that maintain blocks of cached
registers so move the code out of the rbtree cache and into the generic
regcache code.
Refactor the interface slightly as we go to wrap the set bit and enlarge
bitmap operations (since we never do one without the other) and make it
more robust for reads of uncached registers by bounds checking before we
look at the bitmap.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
This will bring no meaningful benefit by itself, it is done as a separate
commit to aid bisection if there are problems with the following commits
adding support for coalescing adjacent writes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mainly useful internally but exported since this is a public API that's
being checked for.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide a helper to do the size based index into a block of registers and
use it when reading a value.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch aims to bring down the average number of nodes
in the rbtree cache and increase the average number of registers
per node. This should improve general lookup and traversal times.
This is achieved by setting the minimum size of a block within the
rbnode to the size of the rbnode itself. This will essentially
cache possibly non-existent registers so to combat this scenario,
we keep a separate bitmap in memory which keeps track of which register
exists. The memory overhead of this change is likely in the order of
~5-10%, possibly less depending on the register file layout. On my test
system with a bitmap of ~4300 bits and a relatively sparse register
layout, the memory requirements for the entire cache did not increase
(the cutting down of nodes which was about 50% of the original number
compensated the situation).
A second patch that can be built on top of this can look at the
ratio `sizeof(*rbnode) / map->cache_word_size' in order to suitably
adjust the block length of each block.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows the cache to sync values directly to the device when stored
in native format and also allows asynchronous I/O.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
_regmap_raw_write() contains code to call regcache_write() to write
values to the cache. That code calls memcpy() to copy the value data to
the start of the work_buf. However, at least when _regmap_raw_write() is
called from _regmap_bus_raw_write(), the value data is in the work_buf,
and this memcpy() operation may over-write part of that value data,
depending on the value of reg_bytes + pad_bytes. At least when using
reg_bytes==1 and pad_bytes==0, corruption of the value data does occur.
To solve this, remove the memcpy() operation, and modify the subsequent
.parse_val() call to parse the original value buffer directly.
At least in the case of 8-bit register address and 16-bit values, and
writes of single registers at a time, this memcpy-then-parse combination
used to cancel each-other out; for a work-buffer containing xx 89 03,
the memcpy changed it to 89 03 03, and the parse_val changed it back to
89 89 03, thus leaving the value uncorrupted. This appears completely
accidental though. Since commit 8a819ff "regmap: core: Split out in
place value parsing", .parse_val only returns the parsed value, and does
not modify the buffer, and hence does not (accidentally) undo the
corruption caused by memcpy(). This caused bogus values to get written
to HW, thus preventing e.g. audio playback on systems with a WM8903
CODEC. This patch fixes that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Display the name for the chip rather than just the primary IRQ so it is
clearer what exactly has failed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The last register block, which falls into the specified range, is not handled
correctly. The formula which calculates the number of register which should be
synced is inverse (and off by one). E.g. if all registers in that block should
be synced only one is synced, and if only one should be synced all (but one) are
synced. To calculate the number of registers that need to be synced we need to
subtract the number of the first register in the block from the max register
number and add one. This patch updates the code accordingly.
The issue was introduced in commit ac8d91c ("regmap: Supply ranges to the sync
operations").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Provide a feel of how much overhead the rbtree cache adds to
the game.
[Slightly reworded output in debugfs -- broonie]
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the rbtree code we are exposing statistics relating to the
number of nodes/registers of the rbtree cache for each of the
devices. Ensure that `map->debugfs' has been initialized before
we attempt to initialize the debugfs entry for the rbtree cache.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
A simple fix to stop us leaking a runtime PM reference in the case where
we fail to enable a device.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRNVQ5AAoJELSic+t+oim93WQQAJIToyJgnuoZfebD3vgT1Tey
YVGM5YY0pL+Ec5Fg91vu/ypFaY888J3UlRtQGxEM13grPunR4y/OflRYAXXTnspW
TcPbcWpkEv464iTQra2GY9Z4gqL9c6fKKBSFwrj74wRb+Jq0BQhrdmbw6U6pMnDS
iAxngfYEdlIULy8gyGnAszJFrQWjYh4U4e7wnUlsOJoZbc7JpW/6ITslwG9PWwK7
h+o7ekjn2anyjAqBStlnSOzQ12kcaam+cDh8Fa8TUmg3HTmFmuCytGA8+XwCVBSQ
ndWIhL1bqeyk7MdS84HjatNRAfPtpSZ9ouxKvLHm/tgALTNt/7CIsXeCm+2OoCQU
7uFJ01WnAstQ58ggEndgjvhr4wGRIp9VZXyVjm8tqH2CLT/UE7H+nnOAcABcd/cn
jZ+t8DQHU2ST1Rvs4Mohax8K6XcOTEQLp/kuhPEUXyqsv73VqIsjloPtqcLbUQdA
RYjMMsSFVFqlPQEOBTDNhGVjrfI4/tlkEh7Kw4VXSZXqf8cvTrAvbWYmMV/MJu2M
pvncD872/jSatRbj5qocnUbOuEyQe3UmdBNtQrdWgseI1z0fyz41X/VvZlzgt+Ll
se8iU4YojEviAUjPzKbKpFwr98r6pmMXtHqxDCYSv47YukiCC5QMenFukMGE5G9R
2qSw38quY1edJiXnq42Y
=D1mN
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap PM fix from Mark Brown:
"A simple fix to stop us leaking a runtime PM reference in the case
where we fail to enable a device."
* tag 'regmap-v3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: irq: call pm_runtime_put in pm_runtime_get_sync failed case
This file lists the register ranges in the register map. The condition
to split the range is based on whether the block is readable or not.
Ensure that we lock the `debugfs_off_cache' list whenever we access
and modify the list. There is a possible race otherwise between the
read() operations of the `registers' file and the `range' file.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't need to use any of the file position information
to calculate the base and max register of each block. Just
use the counter directly.
Set `i = base' at the top to avoid GCC flow analysis bugs. The
value of `i' can never be undefined or 0 in the if (c) { ... }.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the value parsing operations both return the parsed value and
modify the passed buffer. This precludes their use in places like the cache
code so split out the in place modification into a new parse_inplace()
operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's more idiomatic to pass the map structure around and this means we
can use other bits of information from the map.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we're updating a value in place it's more work to read the value and
compare the value with what we're about to set than it is to just write
the value into the cache; there are no further operations after writing
in the code even though there's an early return here.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Trace when we start and complete async writes, and when we start and
finish blocking for their completion. This is useful for performance
analysis of the resulting I/O patterns.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Even in failed case of pm_runtime_get_sync, the usage_count
is incremented. In order to keep the usage_count with correct
value and runtime power management to behave correctly, call
pm_runtime_put(_sync) in such case.
Signed-off-by Liu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Li Fei <fei.li@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
lockdep, but it's a mechanical change.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tiSY
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module update from Rusty Russell:
"The sweeping change is to make add_taint() explicitly indicate whether
to disable lockdep, but it's a mechanical change."
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
MODSIGN: Add option to not sign modules during modules_install
MODSIGN: Add -s <signature> option to sign-file
MODSIGN: Specify the hash algorithm on sign-file command line
MODSIGN: Simplify Makefile with a Kconfig helper
module: clean up load_module a little more.
modpost: Ignore ARC specific non-alloc sections
module: constify within_module_*
taint: add explicit flag to show whether lock dep is still OK.
module: printk message when module signature fail taints kernel.
Some mmio devices have a dedicated interface clock that needs
to be enabled to access their registers. This patch optionally
enables a clock before accessing registers in the regmap_bus
callbacks.
I added (devm_)regmap_init_mmio_clk variants of the init
functions that have an added clk_id string parameter. This
is passed to clk_get to request the clock from the clk
framework.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation to support the regmap debugfs ranges functionality
factor this code out to a separate function. We'll need to ensure
that the value has been correctly calculated from two separate places
in the code.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Optimize this so that we can better guess where to start scanning
from. We know the length of the register field format, therefore
given the file pointer position align to the nearest register
field and scan from there onwards. We round down in this calculation
and we let the rest of the code figure out where to start scanning
from.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We are keeping track of the maximum register as well, this will make
things easier for us in sharing this code with the code implementing
the register ranges functionality. It also simplifies a bit the
calculations when looking for the relevant block:offset from within
the cache.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
At the moment, if the length of the register field format is
N bytes, we can only get anything meaningful back to userspace
by providing a buffer that is N + 2 bytes large. Fix this
so we that we only need to provide a buffer of N bytes.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This fixes:
drivers/base/regmap/regmap.c: In function 'regmap_async_complete_cb':
drivers/base/regmap/regmap.c:1656:3: error: 'TASK_NORMAL' undeclared (first use in this function)
drivers/base/regmap/regmap.c:1656:3: note: each undeclared identifier is reported only once for each function it appears in
drivers/base/regmap/regmap.c: In function 'regmap_async_complete':
drivers/base/regmap/regmap.c:1688:2: error: 'TASK_UNINTERRUPTIBLE' undeclared (first use in this function)
drivers/base/regmap/regmap.c:1688:2: error: implicit declaration of function 'schedule'
An alternative might be to adjust linux/wait.h to include linux/sched.h,
but since that hasn't been done before, I assume we're consciously
avoiding doing that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some use cases like firmware download can transfer a lot of data in quick
succession. With high speed buses these use cases can benefit from having
multiple transfers scheduled at once since this allows the bus to minimise
the delay between transfers.
Support this by adding regmap_raw_write_async(), allowing raw transfers to
be scheduled, and regmap_async_complete() to wait for them to finish.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This commit adds provision for "no-bus" usage of the regmap API. In
this configuration user can provide API with two callbacks 'reg_read'
and 'reg_write' which are to be called when reads and writes to one of
device's registers is performed. This is useful for devices that
expose registers but whose register access sequence does not fit the 'bus'
abstraction.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Gcc warns about the case where regmap_read_debugfs tries to walk an
empty map->debugfs_off_cache list, which would results in uninitialized
variable getting returned, if we hadn't checked the same condition
just before that.
After an originally suggested inferior patch from Arnd Bergmann,
this is the solution that Russell King came up with, sidestepping
the problem by merging the error case for an empty list with the
normal path.
Without this patch, building mxs_defconfig results in:
drivers/base/regmap/regmap-debugfs.c: In function 'regmap_read_debugfs':
drivers/base/regmap/regmap-debugfs.c:147:9: : warning: 'ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
Reported-by: Vincent Stehle <v-stehle@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix up all callers as they were before, with make one change: an
unsigned module taints the kernel, but doesn't turn off lockdep.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We don't want to bomb out early if we failed to get the cache any more,
just soldier on instead and we won't get confused and always return the
first block.
Reported-by: Philipp Zabel <p.zabel@pengutronix.de
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This commit is a preparatory commit to provide "no-bus" configuration
option for regmap API. It adds necessary plumbing needed to have the
ability to provide user define register write function.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This commit is a preparatory commit to provide "no-bus" configuration
option for regmap API. It adds necessary plumbing needed to have the
ability to provide user define register read function.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since regmap already has support for formatting 24 bit wide values, so adding
support for 24 bit wide registers is pretty much straight forward.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than trying to soldier on with a partially allocated cache just
throw the cache away and pretend we don't have one in case we can get a
full cache next time around.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return the start of the last block we tried to read rather than a position,
and also make sure we update the byte position while we're at it. Without
this reads that go into nonexistant areas get confused.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This wasn't implemented but happened to work on test systems due to lack
of wake mask inversion support.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the interrupt status registers are a single block of registers and the
chip supports bulk reads then do a single bulk read rather than pay the
extra I/O cost. This restores the original behaviour which was lost when
support for register striding was added.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While for I2C and SPI devices the overhead of using rbtree for devices with
only one block of registers is negligible the same isn't always going to
be true for MMIO devices where the I/O costs are very much lower. Cater
for these devices by adding a simple flat array type for them where the
lookups are simple array accesses, taking us right back to the original
ASoC cache implementation.
Thanks to Magnus Damm for the discussion which prompted this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regmap-irq framework is used vastly by mfd drivers and some of
devices like TPS65910, TPS80036 do not support the wake base
register to enable wake.
Currently wake in regmap-irq only supported if client driver
passes the wake base register.
As the regmap-irq is mostly used by mfd devices and it is require
to have wake support from these devices in most of use cases,
enabling wake support by default in regmap-irq.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Avoid doing a linear scan of the entire register map for each read() of
the debugfs register dump by recording the offsets where valid registers
exist when we first read the registers file. This assumes the set of
valid registers never changes, if this is not the case invalidation of
the cache will be required.
This could be further improved for large blocks of contiguous registers
by calculating the register we will read from within the block - currently
we do a linear scan of the block. An rbtree may also be worthwhile.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation for doing things a bit more quickly than a linear scan
factor out the initial seek from the debugfs register dump.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If count is less than the size of a register then we may hit integer
wraparound when trying to move backwards to check if we're still in
the buffer. Instead move the position forwards to check if it's still
in the buffer, we are unlikely to be able to allocate a buffer
sufficiently big to overflow here.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Many of the regmap enabled drivers implementing one or more of the
readable, writeable, volatile and precious methods use the same code
pattern:
return ((reg >= X && reg <= Y) || (reg >= W && reg <= Z) || ...)
Switch to a data driven approach, using tables to describe
readable/writeable/volatile and precious registers ranges instead.
The table based check can still be overridden by passing the usual function
pointers via struct regmap_config.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This seems to be the most common way of reporting register numbers, it's
certainly what we do for trace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
val_bytes is of 'size_t', so it should be printed as '%zu'.
Fixes the following build warning on x86:
drivers/base/regmap/regmap.c:872:4: warning: format '%d' expects argument of type 'int', but argument 5 has type 'size_t' [-Wformat]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The regmap_mmio and regmap_irq depend on regmap core, if not select,
we may not compile regmap core and meet compiling errors as follows
if REGMAP_MMIO is selected by client drivers:
drivers/mfd/syscon.c:94:15: error: variable 'syscon_regmap_config' has initializer but incomplete type
drivers/mfd/syscon.c:95:2: error: unknown field 'reg_bits' specified in initializer
drivers/mfd/syscon.c:95:2: warning: excess elements in struct initializer [enabled by default]
drivers/mfd/syscon.c:95:2: warning: (near initialization for 'syscon_regmap_config') [enabled by default]
drivers/mfd/syscon.c:96:2: error: unknown field 'val_bits' specified in initializer
drivers/mfd/syscon.c:96:2: warning: excess elements in struct initializer [enabled by default]
drivers/mfd/syscon.c:96:2: warning: (near initialization for 'syscon_regmap_config') [enabled by default]
drivers/mfd/syscon.c:97:2: error: unknown field 'reg_stride' specified in initializer
drivers/mfd/syscon.c:97:2: warning: excess elements in struct initializer [enabled by default]
drivers/mfd/syscon.c:97:2: warning: (near initialization for 'syscon_regmap_config') [enabled by default]
drivers/mfd/syscon.c: In function 'syscon_probe':
drivers/mfd/syscon.c:124:2: error: invalid use of undefined type 'struct regmap_config'
drivers/mfd/syscon.c:125:2: error: implicit declaration of function 'devm_regmap_init_mmio' [-Werror=implicit-function-declaration]
drivers/mfd/syscon.c:125:17: warning: assignment makes pointer from integer without a cast [enabled by default]
cc1: some warnings being treated as errors
drivers/mfd/Kconfig:
config MFD_SYSCON
bool "System Controller Register R/W Based on Regmap"
depends on OF
select REGMAP_MMIO
help
Select this option to enable accessing system control registers
via regmap.
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is sometimes convenient for a regmap user to override the standard
regmap lock/unlock functions with custom functions.
For instance this can be useful in case an already existing spinlock
or mutex has to be used for locking a set of registers instead of the
internal regmap spinlock/mutex.
Note that the fast_io field of struct regmap_bus is ignored in case
custom locking functions are used.
Signed-off-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Building regmap.o triggers this GCC warning:
drivers/base/regmap/regmap.c: In function ‘regmap_raw_read’:
drivers/base/regmap/regmap.c:1172:6: warning: ‘ret’ may be used uninitialized in this function [-Wmaybe-uninitialized]
Long story short: Jakub Jelinek pointed out that there is a type
mismatch between 'num' in regmap_volatile_range() and 'val_count' in
regmap_raw_read(). And indeed, converting 'num' to the type of
'val_count' (ie, size_t) makes this warning go away.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a block write covers a paged memory region and crosses a window
boundary then rather than failing the write split the transfer up
into multiple writes, making the whole process more transparent for
drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The range code was written to check for return codes less than zero as
errors but throughout the rest of the API return codes not equal to zero
are errors. Change all these checks to match the house style.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a register range is named then provide a debugfs file showing the
contents of the range separately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than just returning a single error code for every possible thing we
can notice print an error message saying what the problem was. This makes
it very much easier to figure out what's wrong and fix it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This makes things consistent with the rest of the API and is actually what
the documentation says. We don't currently have any in tree users so low
cost.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is useful for integration with other subsystems, especially MFD,
and provides an alternative API for users that request their own IRQs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The primary handler will NOT be called if the interrupt nests into
another interrupt thread. Remove it to avoid confusing.
Signed-off-by: Yunfan Zhang <yfzhang@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently, regmap will write 1 to mask_base to mask
an interrupt and write 0 to unmask it.
But some chips do not have an interrupt mask register,
and only have interrupt enable register.
Then we should write 0 to disable interrupt and 1 to enable.
So add an mask_invert flag to handle this.
If it is not set, behavior is same as previous.
If set it to 1, the mask value will be inverted
before written to mask_base
Signed-off-by: Xiaofan Tian <tianxf@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices need to have a runtime PM reference while handling interrupts
to ensure that the register I/O is available. Support this with a flag in
the chip.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The kerneldoc for irq_set_irq_wake() says:
Enable/disable power management wakeup mode, which is
disabled by default.
regmap_irq_set_wake() clears bits to enable wake for an interrupt,
and sets bits to disable wake. Hence, we should set all bits in
wake_buf initially, to mirror the expected disabled state.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a regmap-irq chip has no wake base:
* There's no point calling .irq_set_wake, hence IRQCHIP_SKIP_SET_WAKE.
* If some IRQs in the chip are enabled for wake and some aren't, we
should mask those interrupts that are not wake enabled, so that if
they occur during suspend, the system is not awoken. Hence,
IRQCHIP_MASK_ON_SUSPEND.
Note that IRQCHIP_MASK_ON_SUSPEND is handled by check_wakeup_irqs(),
which always iterates over every single interrupt in the system,
irrespective of whether an interrupt is a child of a controller whose
output interrupt has no wake-enabled inputs and hence is presumably
masked itself. Hence this change might cause interrupt unnecessary
masking operations and associated register I/O.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is intended to give each irq_chip a useful name, rather than hard-
coding them all as "regmap".
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will allow later patches to adjust portions of the irq_chip
individually for each regmap_irq_chip that is created.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Don't write the full register, it's possible there's bits other than the
masks in the same register which we shouldn't be changing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
A number of places in the code were printing error messages that included
the address of a register, but were not calculating the register address
in the same way as the access to the register. Use a temporary to solve
this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When bus->fast_io is set, the locking here is done with spinlocks.
This is currently true for the regmap-mmio bus implementation.
While holding a spinlock we can't go to sleep, various operations
like removing the debugfs entries or re-initializing the cache will
sleep, therefore, shift the locking up to the user.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sometimes for failures during very early init the trace infrastructure
isn't available early enough to be used. For this sort of problem
defining LOG_DEVICE will add printks for basic register I/O on a specific
device, allowing trace to be extracted when the trace system doesn't come
up early enough to work with.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After page update, orginal work_buf has to be restored regardless of
the result.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Devices with register paging or indirectly accessed registers can configure
register mapping to map those on virtual address range. During access to
virtually mapped register range, indirect addressing is processed
automatically, in following steps:
1. selector for page or indirect register is updated (when needed);
2. register in data window is accessed.
Configuration should provide minimum and maximum register for virtual range,
details of selector field for page selection, minimum and maximum register of
data window for indirect access.
Virtual range registers are managed by cache as well as direct access
registers. In order to make indirect access more efficient, selector register
should be declared as non-volatile, if possible.
struct regmap_config is extended with the following:
struct regmap_range_cfg *ranges;
unsigned int n_ranges;
[Also reordered debugfs init to later on since the cleanup code was
conflicting with the new cleanup code for ranges anyway -- broonie]
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Locks are moved to regmap_update_bits(), which allows to reenter internal
function _regmap_update_bits() from inside of regmap read/write routines.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regmap_mmio_gen_context() is only used in regmap-mmio.c. Thus make it static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow chips to provide a bank of registers for controlling the wake state
in a similar fashion to the masks and propagate the wake count to the
parent interrupt controller.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the driver supplied an empty entry in the array of IRQs then return
an error rather than trying to do the mapping. This is intended for use
with handling chip variants and similar situations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The word to be transmitted/received via regmap is composed by the following
parts:
config->reg_bits
config->val_bits
config->pad_bits
,so the total size should be calculated by summing up the number of bits of
each element and using a DIV_ROUND_UP to return the number of bytes.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If debugfs isn't cleaned up, stale files will be left in the filesystem
which will cause an OOPS when accessed the first time, and hang the
accessing application when accessed again, presumably due to some lock
being left held.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will avoid the regmap core converting all addresses and values into
big endian, only for the mmio bus driver to have to convert them back to
native endian.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a field to struct regmap_bus that allows bus drivers to request that
register addresses and values be formatted with a specific endianness.
The default endianness is unchanged from current operation: Big.
Implement native endian formatting/parsing for 16- and 32-bit values.
This will be enough to support regmap-mmio.c.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since there are uses for I2C_M_NOSTART which are much more sensible and
standard than most of the protocol mangling functionality (the main one
being gather writes to devices where something like a register address
needs to be inserted before a block of data) create a new I2C_FUNC_NOSTART
for this feature and update all the users to use it.
Also strengthen the disrecommendation of the protocol mangling while we're
at it.
In the case of regmap-i2c we remove the requirement for mangling as
I2C_M_NOSTART is the only mangling feature which is being used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Ensure that we can't get randconfig breakage by doing the IRQ_DOMAIN
select automatically. Don't just do the select from REGMAP_IRQ to ensure
that the select actually gets noticed.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In some chips the IRQ status registers are not contiguous in the register
map but spaced at even spaces. This is an easy case to handle with minor
changes. It is assume for this purpose that the stride for status is
equal to the stride for mask/ack registers as well.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This gets us up to date with the recommended current kernel infrastructure
and should transparently give us device tree interrupt bindings for any
devices using the framework. If an explicit IRQ mapping is passed in then
a legacy interrupt range is created, otherwise a simple linear mapping is
used. Previously a mapping was mandatory so existing drivers should not
be affected.
A function regmap_irq_get_virq() is provided to allow drivers to map
individual IRQs which should be used in preference to the existing
regmap_irq_chip_get_base() which is only valid if a legacy IRQ range is
provided.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a last minute bug fix that was only just noticed since the code
path that's being exercised here is one that is fairly rarely used. The
changelog for the change itself is extremely clear and the code itself
is obvious to inspection so should be pretty safe.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xcal
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.4' into regmap-stride
regmap: Last minute bug fix for 3.4
This is a last minute bug fix that was only just noticed since the code
path that's being exercised here is one that is fairly rarely used. The
changelog for the change itself is extremely clear and the code itself
is obvious to inspection so should be pretty safe.
Conflicts:
drivers/base/regmap/regmap.c (overlap between the fix and stride code)
The function regmap_bulk_read() calls the regmap_read() for
each register if set of register has volatile and cache is
enabled. In this case, last few register read makes the memory
corruption if the register size is not the size of unsigned int.
The regam_read() takes argument as unsigned int for returning
value and it update the value as
*val = map->format.parse_val(map->work_buf);
This causes complete 4 bytes (size of unsigned int) to get written.
Now if client pass the memory pointer for value which is equal to the
required size of register count in regmap_bulk_read() then last few
register read actually update the memory beyond passed pointer size.
Avoid this by using local variable for read and then do memcpy()
for actual byte copy to passed pointer based on register size.
I allocated one pointer ptr and take first 16 bytes dump of that
pointer then call regmap_bulk_read() with pointer which is just
on top of this allocated pointer and register count of 128. Here
register size is 1 byte.
The memory trace of last 5 register read are as follows:
[ 5.438589] regmap_bulk_read after regamp_read() for register 122
[ 5.447421] 0xef993c20 0xef993c00 0x00000000 0x00000001
[ 5.467535] regmap_bulk_read after regamp_read() for register 123
[ 5.476374] 0xef993c20 0xef993c00 0x00000000 0x00000001
[ 5.496425] regmap_bulk_read after regamp_read() for register 124
[ 5.505260] 0xef993c20 0xef993c00 0x00000000 0x00000001
[ 5.525372] regmap_bulk_read after regamp_read() for register 125
[ 5.534205] 0xef993c00 0xef993c00 0x00000000 0x00000001
[ 5.554258] regmap_bulk_read after regamp_read() for register 126
[ 5.563100] 0xef990000 0xef993c00 0x00000000 0x00000001
[ 5.554258] regmap_bulk_read after regamp_read() for register 127
[ 5.587108] 0xef000000 0xef993c00 0x00000000 0x00000001
Here it is observed that the memory content at first word started changing
on last 3 regmap_read() and so corruption happened.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use devres to implement dev_get_regmap(). This should mean that in almost
all cases devices wishing to take advantage of framework features based on
regmap shouldn't need to explicitly pass the regmap into the framework.
This simplifies device setup a bit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set the use_single_rw flag for devices that use format_write() since
format_write() doesn't support any form of block operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices does not support bulk read and write operations, for them
we have series of single write and read operations.
Signed-off-by: Anthony Olech <Anthony.Olech@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[Fixed coding style, don't check use_single_rw before assign --broonie ]
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we don't have a cached value for a register and we can cache it then
when we do a read a value we should add it to the cache to save rereading
it later on. Do this for single register reads, for block reads the code
would be a little more complex and this covers most practical usage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit f01ee60fff ("regmap: implement register striding") caused the
compile errors below. Fix them.
drivers/base/regmap/regmap-irq.c: In function 'regmap_irq_sync_unlock':
drivers/base/regmap/regmap-irq.c:62:12: error: 'map' undeclared (first use in this function)
drivers/base/regmap/regmap-irq.c:62:12: note: each undeclared identifier is reported only once for each function it appears in
drivers/base/regmap/regmap-irq.c: In function 'regmap_irq_enable':
drivers/base/regmap/regmap-irq.c:77:37: error: 'map' undeclared (first use in this function)
drivers/base/regmap/regmap-irq.c: In function 'regmap_irq_disable':
drivers/base/regmap/regmap-irq.c:85:37: error: 'map' undeclared (first use in this function)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regmap_config.reg_stride is introduced. All extant register addresses
are a multiple of this value. Users of serial-oriented regmap busses will
typically set this to 1. Users of the MMIO regmap bus will typically set
this based on the value size of their registers, in bytes, so 4 for a
32-bit register.
Throughout the regmap code, actual register addresses are used. Wherever
the register address is used to index some array of values, the address
is divided by the stride to determine the index, or vice-versa. Error-
checking is added to all entry-points for register address data to ensure
that register addresses actually satisfy the specified stride. The MMIO
bus ensures that the specified stride is large enough for the register
size.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 79c64d5 "regmap: allow regmap instances to be named" changed the
prototype of regmap_debugfs_init, but didn't update the dummy inline used
when !CONFIG_DEBUGFS. Fix this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices have multiple separate register regions. Logically, one
regmap would be created per region. One issue that prevents this is that
each instance will attempt to create the same debugfs files. Avoid this
by allowing regmaps to be named, and use the name to construct the
debugfs directory name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Two more small fixes:
- Now we have users for it that aren't running Android it turns out that
regcache_sync_region() is much more useful to drivers if it's exported
for use by modules. Who knew?
- Make sure we don't divide by zero when doing debugfs dumps of rbtrees,
not visible up until now because everything was providing at least
some cache on startup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=qm1Q
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull two more small regmap fixes from Mark Brown:
- Now we have users for it that aren't running Android it turns out
that regcache_sync_region() is much more useful to drivers if it's
exported for use by modules. Who knew?
- Make sure we don't divide by zero when doing debugfs dumps of
rbtrees, not visible up until now because everything was providing at
least some cache on startup.
* tag 'regmap-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: prevent division by zero in rbtree_show
regmap: Export regcache_sync_region()
val_len should be a multiple of val_bytes. If it's not, error out early.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These error checks are implemented in regmap core. Remove the duplicate
code from regmap-mmio.c
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some of the error conditions detected by regmap_mmio_*() are pure internal
errors, rather than user-/client-triggerable conditions. Convert these to
BUG().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a basic memory-mapped-IO bus for regmap. It has the following
features and limitations:
* Registers themselves may be 8, 16, 32, or 64-bit. 64-bit is only
supported on 64-bit platforms.
* Register offsets are limited to precisely 32-bit.
* IO is performed using readl/writel, with no provision for using the
__raw_readl or readl_relaxed variants.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some bus types have very fast IO. For these, acquiring a mutex for every
IO operation is a significant overhead. Allow busses to indicate their IO
is fast, and enhance regmap to use a spinlock for those busses.
[Currently limited to native endian registers -- broonie]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The only context needed by I2C and SPI bus definitions is the device
itself; this can be converted to an i2c_client or spi_device in order
to perform IO on the device. However, other bus types may need more
context in order to perform IO. Enable this by having regmap_init accept
a bus_context parameter, and pass this to all bus callbacks. The
existing callbacks simply pass the struct device here. Future bus types
may pass something else.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If there are no nodes in the cache, nodes will be 0, so calculating
"registers / nodes" will cause division by zero.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
regcache_sync_region() isn't going to be useful to most drivers if we
don't export it since otherwise they can't use it when built modular.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This change combines any padding bits into the register address bits when
determining register format handlers to use the next byte-divisible
register size.
A reg_shift member is introduced to the regmap struct to enable fixup
of the reg format.
Format handlers now take an extra parameter specifying the number of
bits to shift the value by.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for devices with 24 data bits.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The code currently passes the register offset in the current block to
regcache_lookup_reg. This works fine as long as there is only one block and with
base register of 0, but in all other cases it will look-up the default for a
wrong register, which can cause unnecessary register writes. This patch fixes
it by passing the actual register number to regcache_lookup_reg.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <stable@vger.kernel.org>
"[RFC PATCH 0/2] audit of linux/device.h users in include/*"
https://lkml.org/lkml/2012/3/4/159
--
Nearly every subsystem has some kind of header with a proto like:
void foo(struct device *dev);
and yet there is no reason for most of these guys to care about the
sub fields within the device struct. This allows us to significantly
reduce the scope of headers including headers. For this instance, a
reduction of about 40% is achieved by replacing the include with the
simple fact that the device is some kind of a struct.
Unlike the much larger module.h cleanup, this one is simply two
commits. One to fix the implicit <linux/device.h> users, and then
one to delete the device.h includes from the linux/include/ dir
wherever possible.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3j4+
-----END PGP SIGNATURE-----
Merge tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull <linux/device.h> avoidance patches from Paul Gortmaker:
"Nearly every subsystem has some kind of header with a proto like:
void foo(struct device *dev);
and yet there is no reason for most of these guys to care about the
sub fields within the device struct. This allows us to significantly
reduce the scope of headers including headers. For this instance, a
reduction of about 40% is achieved by replacing the include with the
simple fact that the device is some kind of a struct.
Unlike the much larger module.h cleanup, this one is simply two
commits. One to fix the implicit <linux/device.h> users, and then one
to delete the device.h includes from the linux/include/ dir wherever
possible."
* tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
device.h: audit and cleanup users in main include dir
device.h: cleanup users outside of linux/include (C files)
Remove for_each_set_bit_cont() after confirming that no one uses
for_each_set_bit_cont() anymore.
[sfr@canb.auug.org.au: regmap: cope with bitops API change]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For files that are actively using linux/device.h, make sure
that they call it out. This will allow us to clean up some
of the implicit uses of linux/device.h within include/*
without introducing build regressions.
Yes, this was created by "cheating" -- i.e. the headers were
cleaned up, and then the fallout was found and fixed, and then
the two commits were reordered. This ensures we don't introduce
build regressions into the git history.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
[Fix for breakage which will be introduced during the merge window via
header reworks in another tree, the regmap tree does include device.h
but Paul's tree breaks that. Reworded subject to reflect -- broonie]
regmap.s uses devres_alloc() and others that are prototyped in device.h.
Include that to solve the following:
drivers/base/regmap/regmap.c: In function 'devm_regmap_init':
drivers/base/regmap/regmap.c:331:2: error: implicit declaration of function 'devres_alloc' [-Werror=implicit-function-declaration]
drivers/base/regmap/regmap.c:338:3: error: implicit declaration of function 'devres_add' [-Werror=implicit-function-declaration]
drivers/base/regmap/regmap.c:340:3: error: implicit declaration of function 'devres_free' [-Werror=implicit-function-declaration]
drivers/base/regmap/regmap.c: In function '_regmap_raw_write':
drivers/base/regmap/regmap.c:421:5: error: implicit declaration of function 'dev_err' [-Werror=implicit-function-declaration]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Most of the current users have register 0 as a volatile register or don't
have a register 0 so it's not been apparent that it's not getting synced.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove unused module.h and/or replace with export.h
as required.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide a regcache_sync_region() operation which allows drivers to
write only part of the cache back to the hardware. This is intended
for use in cases like power domains or DSP memories where part of the
device register map may be reset without fully resetting the device.
Fully supporting these devices is likely to require additional work to
make specific regions of the register map cache only while they are in
reset, but this is enough for most devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to allow us to support partial sync operations add minimum and
maximum register arguments to the sync operation and update the rbtree
and lzo caches to use this new information. The LZO implementation is
obviously not good, we could exit the iteration earlier, but there may
be room for more wide reaching optimisation there.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Previously the cache would never be marked clean, meaning syncs would
never be suppressed which isn't the end of the world but could be
inefficient.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's not used as all cache types have sync operations so it's just dead
code which never gets tested.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a file called 'name' containing the name of the driver.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To enable writing to the regmap debugfs registers file users will
need to modify the source directly and #define REGMAP_ALLOW_WRITE_DEBUGFS.
The reason for this is that it is dangerous to expose this
functionality in general where clients could potentially be PMICs.
[A couple of minor style updates -- broonie]
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fall back to a register by register read to do so; most likely we'll be
cache only so the overhead will be low.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Generic infrastructure based on top of regmap may want to operate on
blocks of data and therefore find it useful to find the size of the
register values. Provide an accessor operation for this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
During regcache_init, if client has not passed the
default data of cached register then it is directly
read from the hw to initialize cache. This hw register
read happens before cache ops are initialized and hence
avoiding register read to check for the data available
on cache or not by enabling flag of cache_bypass.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently registers with a value of 0 are ignored when initializing the register
defaults from raw defaults. This worked in the past, because registers without a
explicit default were assumed to have a default value of 0. This was changed in
commit b03622a8 ("regmap: Ensure rbtree syncs registers set to zero properly").
As a result registers, which have a raw default value of 0 are now assumed to
have no default. This again can result in unnecessary writes when syncing the
cache. It will also result in unnecessary reads for e.g. the first update
operation. In the case where readback is not possible this will even let the
update operation fail, if the register has not been written to before.
So this patch removes the check. Instead it adds a check to ignore raw defaults
for registers which are volatile, since those registers are not cached.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The bulk_write() supports the data transfer to multi
register which takes the data into cpu_endianness format
and does formatting of data to device format before
sending to device.
The transfer can be completed in single transfer or multiple
transfer based on data formatting.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adding support for caching of data into the
non-volatile register from the call of reg_raw_write().
This will allow the larger block of data write into multiple
register without worrying whether register is cached or not
through reg_raw_write().
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The first parameter should be "number of elements" and the second parameter
should be "element size".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This was a cut'n'paste from some older code.
Since we're about to add debugfs support don't do the obvious thing and
use bool, use u32 instead (which debugfs has been using since time
immemorial).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regcache_set_val() returns false if cache[idx] != val.
Thus it actually is not unreachable.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Save error handling and unwinding code in drivers by providing managed
versions of the regmap init functions, simplifying usage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using .format_write means, we have a custom function to write to the
chip, but not to read back. Also, mark registers as "not precious" and
"not volatile" which is implicit because we cannot read them. Make those
functions use 'regmap_readable' to reuse the checks done there.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For the upcoming 2/6-format, we don't see debugfs output otherwise,
since the current division results in 0. I'd think 10/14 is broken
currently, too.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Most of the data exposed via debugfs is for or from the cache so reset
all the debugfs configuration to make sure everything is up to date with
the latest configuration, especially if we're changing cache type.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On the basis that if we don't actually need to resync the cache then the
patches are probably also already applied.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown
Stephen Warren
Stratos Karafotis
Sachin Kamat
Dimitris Papastamos
Lars-Peter Clausen
Linus Torvalds
Li Fei
Philipp Zabel
Axel Lin
Andrey Smirnov
Russell King
Nestor Ovroy
Rusty Russell
Laxman Dewangan
Davide Ciminaghi
Fabio Estevam
Dong Aisheng
Paul Bolle
Yunfan Zhang
Xiaofan Tian
Krystian Garbaciak
Axel Lin
Graeme Gregory
Ashish Jangam
Stephen Boyd
Marc Reilly
Akinobu Mita
Paul Gortmaker
Stephen Warren
Wolfram Sang