Code will always think there are 16 banks because of a typo
Reported-by: Misha
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Broadwell-DE is the microserver version of next generation Xeon
processors. A whole bunch of new PCIe device ids, but otherwise
pretty much the same as Haswell.
Acked-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Haswell moved the TOLM/TOHM registers to a different device and offset.
The sb_edac driver accounted for the change of device, but not for the
new offset. There was also a typo in the constant to fill in the low
26 bits (was 0x1ffffff, should be 0x3ffffff).
This resulted in a bogus value for the top of low memory:
EDAC DEBUG: get_memory_layout: TOLM: 0.032 GB (0x0000000001ffffff)
which would result in EDAC refusing to translate addresses for
errors above the bogus value and below 4GB:
sbridge MC3: HANDLING MCE MEMORY ERROR
sbridge MC3: CPU 0: Machine Check Event: 0 Bank 7: 8c00004000010090
sbridge MC3: TSC 0
sbridge MC3: ADDR 2000000
sbridge MC3: MISC 523eac86
sbridge MC3: PROCESSOR 0:306f3 TIME 1414600951 SOCKET 0 APIC 0
MC3: 1 CE Error at TOLM area, on addr 0x02000000 on any memory ( page:0x0 offset:0x0 grain:32 syndrome:0x0)
With the fix we see the correct TOLM value:
DEBUG: get_memory_layout: TOLM: 2.048 GB (0x000000007fffffff)
and we decode address 2000000 correctly:
sbridge MC3: HANDLING MCE MEMORY ERROR
sbridge MC3: CPU 0: Machine Check Event: 0 Bank 7: 8c00004000010090
sbridge MC3: TSC 0
sbridge MC3: ADDR 2000000
sbridge MC3: MISC 523e1086
sbridge MC3: PROCESSOR 0:306f3 TIME 1414601319 SOCKET 0 APIC 0
DEBUG: get_memory_error_data: SAD interleave package: 0 = CPU socket 0, HA 0, shiftup: 0
DEBUG: get_memory_error_data: TAD#0: address 0x0000000002000000 < 0x000000007fffffff, socket interleave 1, channel interleave 4 (offset 0x00000000), index 0, base ch: 0, ch mask: 0x01
DEBUG: get_memory_error_data: RIR#0, limit: 4.095 GB (0x00000000ffffffff), way: 1
DEBUG: get_memory_error_data: RIR#0: channel address 0x00200000 < 0xffffffff, RIR interleave 0, index 0
DEBUG: sbridge_mce_output_error: area:DRAM err_code:0001:0090 socket:0 channel_mask:1 rank:0
MC3: 1 CE memory read error on CPU_SrcID#0_Channel#0_DIMM#0 (channel:0 slot:0 page:0x2000 offset:0x0 grain:32 syndrome:0x0 - area:DRAM err_code:0001:0090 socket:0 channel_mask:1 rank:0)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
sb_edac controls a large number of different PCI functions. Rather
than registering as a normal PCI driver for all of them, it
registers for just one so that it gets probed and, at probe time, it
looks for all the others.
Coincidentally, the device it registers for also contains the SMBUS
registers, so the PCI core will refuse to probe both sb_edac and a
future iMC SMBUS driver. The drivers don't actually conflict, so
just change sb_edac's device table to probe a different device.
An alternative fix would be to merge the two drivers, but sb_edac
will also refuse to load on non-ECC systems, whereas i2c_imc would
still be useful without ECC.
The only user-visible change should be that sb_edac appears to bind
a different device.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Rui Wang <ruiv.wang@gmail.com>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The i2c_imc driver will use two of them, and moving only part of
the list seems messier.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Intel IA32 SDM Table 15-14 defines channel 0xf as 'not specified', but
EDAC doesn't know about this and returns and INTERNAL ERROR when the
channel is greater than NUM_CHANNELS:
kernel: [ 1538.886456] CPU 0: Machine Check Exception: 0 Bank 1: 940000000000009f
kernel: [ 1538.886669] TSC 2bc68b22e7e812 ADDR 46dae7000 MISC 0 PROCESSOR 0:306e4 TIME 1390414572 SOCKET 0 APIC 0
kernel: [ 1538.971948] EDAC MC1: INTERNAL ERROR: channel value is out of range (15 >= 4)
kernel: [ 1538.972203] EDAC MC1: 0 CE memory read error on unknown memory (slot:0 page:0x46dae7 offset:0x0 grain:0 syndrome:0x0 - area:DRAM err_code:0000:009f socket:1 channel_mask:1 rank:0)
This commit changes sb_edac to forward a channel of -1 to EDAC if the
channel is not specified. edac_mc_handle_error() sets the channel to -1
internally after the error message anyway, so this commit should have no
effect other than avoiding the INTERNAL ERROR message when the channel
is not specified.
Signed-off-by: Seth Jennings <sjenning@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Haswell memory controllers are very similar to Ivy Bridge and Sandy Bridge
ones. This patch adds support to Haswell based systems.
[m.chehab@samsung.com: Fix CodingStyle issues]
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When a MC is handled, the correct sbridge_dev is searched based on the node,
checking again later with the assumption the first memory controller found is
the first socket's memory controller is a bogus assumption. Get rid of it.
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
channel_mask will be used in the future to determine which group of memory
modules is causing the errors since when mirroring, lockstep and close page
are enabled you can't. While that doesn't happen, use the channel_mask to
determine the channel instead of relying on the MC event/exception.
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch fixes the obvious bug while handling the socket/HA bitmask used in
Ivy Bridge memory controllers.
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch changes the way devices are searched by using product id instead of
device/function numbers. Tested in a Sandy Bridge and a Ivy Bridge machine to
make sure everything works properly.
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Haswell has a different way to retrieve RIR limits, make this procedure per
model.
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Haswell has a different way to retrieve the node id, make so this procedure
can be reimplemented.
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Haswell has different register, offset to determine memory type and supports
DDR4 in some models. This patch makes it easier to have a different method
depending on the memory controller type.
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
"The main set of series of patches for media subsystem, including:
- document RC sysfs class
- added an API to setup scancode to allow waking up systems using the
Remote Controller
- add API for SDR devices. Drivers are still on staging
- some API improvements for getting EDID data from media
inputs/outputs
- new DVB frontend driver for drx-j (ATSC)
- one driver (it913x/it9137) got removed, in favor of an improvement
on another driver (af9035)
- added a skeleton V4L2 PCI driver at documentation
- added a dual flash driver (lm3646)
- added a new IR driver (img-ir)
- added an IR scancode decoder for the Sharp protocol
- some improvements at the usbtv driver, to allow its core to be
reused.
- added a new SDR driver (rtl2832u_sdr)
- added a new tuner driver (msi001)
- several improvements at em28xx driver to fix PM support, device
removal and to split the V4L2 specific bits into a separate
sub-driver
- one driver got converted to videobuf2 (s2255drv)
- the e4000 tuner driver now follows an improved binding model
- some fixes at V4L2 compat32 code
- several fixes and enhancements at videobuf2 code
- some cleanups at V4L2 API documentation
- usual driver enhancements, new board additions and misc fixups"
[ NOTE! This merge effective drops commit 4329b93b28 ("of: Reduce
indentation in of_graph_get_next_endpoint").
The of_graph_get_next_endpoint() function was moved and renamed by
commit fd9fdb78a9 ("[media] of: move graph helpers from
drivers/media/v4l2-core to drivers/of"). It was originally called
v4l2_of_get_next_endpoint() and lived in the file
drivers/media/v4l2-core/v4l2-of.c.
In that original location, it was then fixed to support empty port
nodes by commit b9db140c1e ("[media] v4l: of: Support empty port
nodes"), and that commit clashes badly with the dropped "Reduce
intendation" commit. I had to choose one or the other, and decided
that the "Support empty port nodes" commit was more important ]
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (426 commits)
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
Revert "[media] em28xx-dvb: fix PCTV 461e tuner I2C binding"
[media] em28xx: fix PCTV 290e LNA oops
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
[media] m88ds3103: fix bug on .set_tone()
[media] saa7134: fix WARN_ON during resume
[media] v4l2-dv-timings: add module name, description, license
[media] videodev2.h: add parenthesis around macro arguments
[media] saa6752hs: depends on CRC32
[media] si4713: fix Kconfig dependencies
[media] Sensoray 2255 uses videobuf2
[media] adv7180: free an interrupt on failure paths in init_device()
[media] e4000: make VIDEO_V4L2 dependency optional
[media] af9033: Don't export functions for the hardware filter
[media] af9035: use af9033 PID filters
[media] af9033: implement PID filter
[media] rtl2832_sdr: do not use dynamic stack allocation
[media] e4000: fix 32-bit build error
[media] em28xx-audio: make sure audio is unmuted on open()
[media] DocBook media: v4l2_format_sdr was renamed to v4l2_sdr_format
...
Pull sb_edac patches from Mauro Carvalho Chehab:
"A couple sb_edac driver improvements, cleaning a little bit the amount
of data sent to dmesg, and fixing one error message"
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
sb_edac: mark MCE messages as KERN_DEBUG
sb_edac: use "event" instead of "exception" when MC wasnt signaled
Since the driver is decoding the MCE, it's useless to have these
messages printed unless you're debugging a problem in the driver.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Corrected Errors are MC events, not exceptions and reporting as the
later might confuse users.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On a system with four Intel processors, it generates too many messages
"EDAC sbridge: Seeking for: dev 1d.3 PCI ID xxxx". And it doesn't give
many useful information for normal users, so change log level from INFO
to DEBUG.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Link: http://lkml.kernel.org/r/1392613824-11230-1-git-send-email-jiang.liu@linux.intel.com
Acked-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
There are several left overs with my old email address.
Remove their occurrences and add myself at CREDITS, to
allow people to be able to reach me on my new addresses.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull x86 RAS changes from Ingo Molnar:
- SCI reporting for other error types not only correctable ones
- GHES cleanups
- Add the functionality to override error reporting agents as some
machines are sporting a new extended error logging capability which,
if done properly in the BIOS, makes a corresponding EDAC module
redundant
- PCIe AER tracepoint severity levels fix
- Error path correction for the mce device init
- MCE timer fix
- Add more flexibility to the error injection (EINJ) debugfs interface
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, mce: Fix mce_start_timer semantics
ACPI, APEI, GHES: Cleanup ghes memory error handling
ACPI, APEI: Cleanup alignment-aware accesses
ACPI, APEI, GHES: Do not report only correctable errors with SCI
ACPI, APEI, EINJ: Changes to the ACPI/APEI/EINJ debugfs interface
ACPI, eMCA: Combine eMCA/EDAC event reporting priority
EDAC, sb_edac: Modify H/W event reporting policy
EDAC: Add an edac_report parameter to EDAC
PCI, AER: Fix severity usage in aer trace event
x86, mce: Call put_device on device_register failure
* misc small enhancements/fixes all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=EJ+3
-----END PGP SIGNATURE-----
Merge tag 'edac_for_3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
- mpc85xx PCIe error interrupt support
- misc small enhancements/fixes all over the place.
* tag 'edac_for_3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC: Don't try to cancel workqueue when it's never setup
e752x_edac: Fix pci_dev usage count
sb_edac: Mark get_mci_for_node_id as static
EDAC: Mark edac_create_debug_nodes as static
amd64_edac: Remove "amd64" prefix from static functions
amd64_edac: Simplify code around decode_bus_error
amd64_edac: Mark amd64_decode_bus_error as static
EDAC: Remove DEFINE_PCI_DEVICE_TABLE macro
amd64_edac: Fix condition to verify max channels allowed for F15 M30h
edac/85xx: Add PCIe error interrupt edac support
machines are sporting a new extended error logging capability which, if
done properly in the BIOS, makes a corresponding EDAC module redundant,
from Gong Chen.
* PCIe AER tracepoint severity levels fix, from Rui Wang.
* Error path correction for the mce device init, from Levente Kurusa.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=r//I
-----END PGP SIGNATURE-----
Merge tag 'ras_for_3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp into x86/ras
Pull RAS updates from Borislav Petkov:
* Add the functionality to override error reporting agents as some
machines are sporting a new extended error logging capability which, if
done properly in the BIOS, makes a corresponding EDAC module redundant,
from Gong Chen.
* PCIe AER tracepoint severity levels fix, from Rui Wang.
* Error path correction for the mce device init, from Levente Kurusa.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch marks the function get_mci_for_node_id() as static because it
is not used outside of sb_edac.c.
Thus, it also eliminates the following warning:
drivers/edac/sb_edac.c:918:22: warning: no previous prototype for ‘get_mci_for_node_id’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Link: http://lkml.kernel.org/r/0441f508186fc4eeabc8e9c3e4dde013d99405d4.1387029387.git.rashika.kheria@gmail.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Newer Intel platforms support more than one method to report H/W event.
On this kind of platform, H/W event report can adopt new method and
traditional EDAC method should be disabled. Moreover, if EDAC event
report method is set to *force*, it means event must be reported via
EDAC interface. IOW, it overrides the default event report policy.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1386310630-12529-3-git-send-email-gong.chen@linux.intel.com
[ Boris: massage commit and error messages ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Currently, there is no other bus that has something like this macro for
their device ids. Thus, DEFINE_PCI_DEVICE_TABLE macro should be removed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Link: http://lkml.kernel.org/r/001c01ceefb3$5724d860$056e8920$%han@samsung.com
[ Boris: swap commit message with better one. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Fix this:
In file included from drivers/edac/sb_edac.c:27:0:
drivers/edac/sb_edac.c: In function ‘sbridge_mce_output_error’:
drivers/edac/edac_core.h:50:8: warning: ‘limit’ may be used uninitialized in this function [-Wmaybe-uninitialized]
printk(level "EDAC " prefix ": " fmt, ##arg)
^
drivers/edac/sb_edac.c:948:25: note: ‘limit’ was declared here
u64 ch_addr, offset, limit, prv = 0;
Limit can be initialized to 0. The only way limit wouldn't be
initialized is if there are no DIMMs present (which would be a bug of
course) and it'd fail on the next test.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Link: http://lkml.kernel.org/r/20131121122021.GD26009@pd.tnic
Signed-off-by: Borislav Petkov <bp@suse.de>
Pull EDAC driver updates from Mauro Carvalho Chehab:
- sb_edac: add support for Ivy Bridge support
- cell_edac: add a missing of_node_put() call
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
cell_edac: fix missing of_node_put
sb_edac: add support for Ivy Bridge
sb_edac: avoid decoding the same error multiple times
sb_edac: rename mci_bind_devs()
sb_edac: enable multiple PCI id tables to be used
sb_edac: rework sad_pkg
sb_edac: allow different interleave lists
sb_edac: allow different dram_rule arrays
sb_edac: isolate TOHM retrieval
sb_edac: rename pci_br
sb_edac: isolate TOLM retrieval
sb_edac: make RANK_CFG_A value part of sbridge_info
Since Ivy Bridge memory controller is very similar to Sandy Bridge, it's
wiser to modify sb_edac to support both instead of creating another
driver.
[m.chehab@samsung.com: Fix CodingStyle]
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Whenever the extended error reporting is active, multiple MCEs will be
generated for the same event, which will lead to multiple repeated
errors to be reported. So check ADDRV and only decode the error if the
MCE address is valid.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is in preparation for Ivy Bridge support
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is needed to allow separated PCI id tables for Sandy Bridge and Ivy
Bridge.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is in preparation for Ivy Bridge support
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is in preparation for Ivy Bridge support
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is in preparation for Ivy Bridge support
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ivy Bridge has more than one, so rename pci_br to pci_br0
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is in preparation for the Ivy Bridge support.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is in preparation of Ivy Bridge support.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
GENMASK is used to create a contiguous bitmask([hi:lo]). It is
implemented twice in current kernel. One is in EDAC driver, the other
is in SiS/XGI FB driver. Move it to a more generic place for other
usage.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The Sandy Bridge EDAC driver uses a register in the IMC_DDRIO CSR
space to determine the type of DIMMs (registered or unregistered).
But this device does not exist on some single socket Sandy Bridge
servers. While the type of DIMMs is nice to know, it is not essential
for this driver's other functions. So it seems harsh to have it
refuse to load at all when it cannot find this device.
Make the check for this device be optional. If it isn't present
just report the memory type as "MEM_UNKNOWN".
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJRFWw4AAoJEHm+PkMAQRiGnTAH/jBHA2umNc3lc7VkUpusve4q
GGIlNzYh6iuvIGwKQVj9YPsl37qtQnkDUmY8f8WxZjfxiIDw3TkRKDgNLJaM3Jy5
E426/FGlRx/Iia5+4tuBeoVYMoIPnndgW5lEAMRK1SvhTByhIYAXsaM0UwPBetb+
Z5NMdH1f1HVF7RCCmHAkzEk9z78UpdeCzI0t0XuasP2hp2ARAcE1okdO7fNaLiyo
EmenGhRvy9bAsbRwV0rCdl0rQiZXEYM353DWS7n6q4fyVm8MXFwloUxnWCJTzOIL
ZLJaz18adFj7Ip/X6ksnMQiQU2Q3B7aThs5ycv0QGxxL2rDFveYRRQ5ICrXOy3M=
=jjBc
-----END PGP SIGNATURE-----
Merge tag 'v3.8-rc7' into next
Linux 3.8-rc7
* tag 'v3.8-rc7': (12052 commits)
Linux 3.8-rc7
net: sctp: sctp_endpoint_free: zero out secret key data
net: sctp: sctp_setsockopt_auth_key: use kzfree instead of kfree
atm/iphase: rename fregt_t -> ffreg_t
ARM: 7641/1: memory: fix broken mmap by ensuring TASK_UNMAPPED_BASE is aligned
ARM: DMA mapping: fix bad atomic test
ARM: realview: ensure that we have sufficient IRQs available
ARM: GIC: fix GIC cpumask initialization
net: usb: fix regression from FLAG_NOARP code
l2tp: dont play with skb->truesize
net: sctp: sctp_auth_key_put: use kzfree instead of kfree
netback: correct netbk_tx_err to handle wrap around.
xen/netback: free already allocated memory on failure in xen_netbk_get_requests
xen/netback: don't leak pages on failure in xen_netbk_tx_check_gop.
xen/netback: shutdown the ring if it contains garbage.
drm/ttm: fix fence locking in ttm_buffer_object_transfer, 2nd try
virtio_console: Don't access uninitialized data.
net: qmi_wwan: add more Huawei devices, including E320
net: cdc_ncm: add another Huawei vendor specific device
ipv6/ip6_gre: fix error case handling in ip6gre_tunnel_xmit()
...
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, and __devexit
from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Mark Gross <mark.gross@intel.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Tim Small <tim@buttersideup.com>
Cc: Ranganathan Desikan <ravi@jetztechnologies.com>
Cc: "Arvind R." <arvino55@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Daney <david.daney@cavium.com>
Cc: Egor Martovetsky <egor@pasemi.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sandy bridge EDAC is calculating the memory size with overflow.
Basically, the size field and the integer calculation is using 32 bits.
More bits are needed, when the DIMM memories have high density.
The net result is that memories are improperly reported there, when
high-density DIMMs are used:
EDAC DEBUG: in drivers/edac/sb_edac.c, line at 591: mc#0: channel 0, dimm 0, -16384 Mb (-4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800
EDAC DEBUG: in drivers/edac/sb_edac.c, line at 591: mc#0: channel 1, dimm 0, -16384 Mb (-4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800
As the number of pages value is handled at the EDAC core as unsigned
ints, the driver shows the 16 GB memories at sysfs interface as 16760832
MB! The fix is simple: calculate the number of pages as unsigned 64-bits
integer.
After the patch, the memory size (16 GB) is properly detected:
EDAC DEBUG: in drivers/edac/sb_edac.c, line at 592: mc#0: channel 0, dimm 0, 16384 Mb (4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800
EDAC DEBUG: in drivers/edac/sb_edac.c, line at 592: mc#0: channel 1, dimm 0, 16384 Mb (4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* devel: (33 commits)
edac i5000, i5400: fix pointer math in i5000_get_mc_regs()
edac: allow specifying the error count with fake_inject
edac: add support for Calxeda highbank L2 cache ecc
edac: add support for Calxeda highbank memory controller
edac: create top-level debugfs directory
sb_edac: properly handle error count
i7core_edac: properly handle error count
edac: edac_mc_handle_error(): add an error_count parameter
edac: remove arch-specific parameter for the error handler
amd64_edac: Don't pass driver name as an error parameter
edac_mc: check for allocation failure in edac_mc_alloc()
edac: Increase version to 3.0.0
edac_mc: Cleanup per-dimm_info debug messages
edac: Convert debugfX to edac_dbg(X,
edac: Use more normal debugging macro style
edac: Don't add __func__ or __FILE__ for debugf[0-9] msgs
Edac: Add ABI Documentation for the new device nodes
edac: move documentation ABI to ABI/testing/sysfs-devices-edac
i7core_edac: change the mem allocation scheme to make Documentation/kobject.txt happy
edac: change the mem allocation scheme to make Documentation/kobject.txt happy
...
Instead of reporting the error count via driver-specific details,
use the new way provided by edac_mc_handle_error.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to avoid loosing error events, it is desirable to group
error events together and generate a single trace for several identical
errors.
The trace API already allows reporting multiple errors. Change the
handle_error function to also allow that.
The changes at the drivers were made by this small script:
$file .=$_ while (<>);
$file =~ s/(edac_mc_handle_error)\s*\(([^\,]+)\,([^\,]+)\,/$1($2,$3, 1,/g;
print $file;
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tony Luck
Jim Snow
Andy Lutomirski
Seth Jennings
Aristeu Rozanski
Mauro Carvalho Chehab
Linus Torvalds
Aristeu Rozanski
Jiang Liu
Ingo Molnar
Rashika Kheria
Chen, Gong
Jingoo Han
Mauro Carvalho Chehab
Greg Kroah-Hartman