X86 IO/APIC and MSI interrupts (when used without interrupts remapping)
require that the affinity setup on startup is done before the interrupt is
enabled for the first time as the non-remapped operation mode cannot safely
migrate enabled interrupts from arbitrary contexts. Provide a new irq chip
flag which allows affected hardware to request this.
This has to be opt-in because there have been reports in the past that some
interrupt chips cannot handle affinity setting before startup.
Fixes: 1840475676 ("genirq: Expose default irq affinity mask (take 3)")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210729222542.779791738@linutronix.de
The whole call to note_interrupt() can be avoided or return early when
interrupts would be marked accordingly. For IPI handlers which always
return HANDLED the whole procedure is pretty pointless to begin with.
Add a IRQF_NO_DEBUG flag and mark the interrupt accordingly if supplied
when the interrupt is requested.
When noirqdebug is set on the kernel commandline, then the interrupt is
marked unconditionally so that there is only one condition in the hotpath
to evaluate.
[ clg: Add changelog ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/7a8ad02f-63a8-c1aa-fdd1-39d973593d02@kaod.org
- MTE asynchronous support for KASan. Previously only synchronous
(slower) mode was supported. Asynchronous is faster but does not allow
precise identification of the illegal access.
- Run kernel mode SIMD with softirqs disabled. This allows using NEON in
softirq context for crypto performance improvements. The conditional
yield support is modified to take softirqs into account and reduce the
latency.
- Preparatory patches for Apple M1: handle CPUs that only have the VHE
mode available (host kernel running at EL2), add FIQ support.
- arm64 perf updates: support for HiSilicon PA and SLLC PMU drivers, new
functions for the HiSilicon HHA and L3C PMU, cleanups.
- Re-introduce support for execute-only user permissions but only when
the EPAN (Enhanced Privileged Access Never) architecture feature is
available.
- Disable fine-grained traps at boot and improve the documented boot
requirements.
- Support CONFIG_KASAN_VMALLOC on arm64 (only with KASAN_GENERIC).
- Add hierarchical eXecute Never permissions for all page tables.
- Add arm64 prctl(PR_PAC_{SET,GET}_ENABLED_KEYS) allowing user programs
to control which PAC keys are enabled in a particular task.
- arm64 kselftests for BTI and some improvements to the MTE tests.
- Minor improvements to the compat vdso and sigpage.
- Miscellaneous cleanups.
-----BEGIN PGP SIGNATURE-----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=6NGI
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- MTE asynchronous support for KASan. Previously only synchronous
(slower) mode was supported. Asynchronous is faster but does not
allow precise identification of the illegal access.
- Run kernel mode SIMD with softirqs disabled. This allows using NEON
in softirq context for crypto performance improvements. The
conditional yield support is modified to take softirqs into account
and reduce the latency.
- Preparatory patches for Apple M1: handle CPUs that only have the VHE
mode available (host kernel running at EL2), add FIQ support.
- arm64 perf updates: support for HiSilicon PA and SLLC PMU drivers,
new functions for the HiSilicon HHA and L3C PMU, cleanups.
- Re-introduce support for execute-only user permissions but only when
the EPAN (Enhanced Privileged Access Never) architecture feature is
available.
- Disable fine-grained traps at boot and improve the documented boot
requirements.
- Support CONFIG_KASAN_VMALLOC on arm64 (only with KASAN_GENERIC).
- Add hierarchical eXecute Never permissions for all page tables.
- Add arm64 prctl(PR_PAC_{SET,GET}_ENABLED_KEYS) allowing user programs
to control which PAC keys are enabled in a particular task.
- arm64 kselftests for BTI and some improvements to the MTE tests.
- Minor improvements to the compat vdso and sigpage.
- Miscellaneous cleanups.
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (86 commits)
arm64/sve: Add compile time checks for SVE hooks in generic functions
arm64/kernel/probes: Use BUG_ON instead of if condition followed by BUG.
arm64: pac: Optimize kernel entry/exit key installation code paths
arm64: Introduce prctl(PR_PAC_{SET,GET}_ENABLED_KEYS)
arm64: mte: make the per-task SCTLR_EL1 field usable elsewhere
arm64/sve: Remove redundant system_supports_sve() tests
arm64: fpsimd: run kernel mode NEON with softirqs disabled
arm64: assembler: introduce wxN aliases for wN registers
arm64: assembler: remove conditional NEON yield macros
kasan, arm64: tests supports for HW_TAGS async mode
arm64: mte: Report async tag faults before suspend
arm64: mte: Enable async tag check fault
arm64: mte: Conditionally compile mte_enable_kernel_*()
arm64: mte: Enable TCO in functions that can read beyond buffer limits
kasan: Add report for async mode
arm64: mte: Drop arch_enable_tagging()
kasan: Add KASAN mode kernel parameter
arm64: mte: Add asynchronous mode support
arm64: Get rid of CONFIG_ARM64_VHE
arm64: Cope with CPUs stuck in VHE mode
...
Some architectures want to provide the generic set_handle_irq() API, but
for structural reasons need to provide their own implementation. For
example, arm64 needs to do this to provide uniform set_handle_irq() and
set_handle_fiq() registration functions.
Make this possible by allowing architectures to provide their own
implementation of set_handle_irq when CONFIG_GENERIC_IRQ_MULTI_HANDLER
is not selected.
Signed-off-by: Marc Zyngier <maz@kernel.org>
[Mark: expand commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Hector Martin <marcan@marcan.st>
Cc: James Morse <james.morse@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210315115629.57191-2-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since commit a85a6c86c2 ("driver core: platform: Clarify that IRQ 0
is invalid"), having a linux-irq with number 0 will trigger a WARN()
when calling platform_get_irq*() to retrieve that linux-irq.
Since [devm_]irq_alloc_desc allocs a single irq and since irq 0 is not used
on some systems, it can return 0, triggering that WARN(). This happens
e.g. on Intel Bay Trail and Cherry Trail devices using the LPE audio engine
for HDMI audio:
0 is an invalid IRQ number
WARNING: CPU: 3 PID: 472 at drivers/base/platform.c:238 platform_get_irq_optional+0x108/0x180
Modules linked in: snd_hdmi_lpe_audio(+) ...
Call Trace:
platform_get_irq+0x17/0x30
hdmi_lpe_audio_probe+0x4a/0x6c0 [snd_hdmi_lpe_audio]
---[ end trace ceece38854223a0b ]---
Change the 'from' parameter passed to __[devm_]irq_alloc_descs() by the
[devm_]irq_alloc_desc macros from 0 to 1, so that these macros will no
longer return 0.
Fixes: a85a6c86c2 ("driver core: platform: Clarify that IRQ 0 is invalid")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201221185647.226146-1-hdegoede@redhat.com
Provide an accessor to the effective interrupt affinity mask. Going to be
used to replace open coded fiddling with the irq descriptor.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201210194042.967177918@linutronix.de
- Preliminary support for managed interrupts on platform devices
- Correctly identify allocation of MSIs proxyied by another device
- Remove the fasteoi IPI flow which has been proved useless
- Generalise the Ocelot support to new SoCs
- Improve GICv4.1 vcpu entry, matching the corresponding KVM optimisation
- Work around spurious interrupts on Qualcomm PDC
- Random fixes and cleanups
-----BEGIN PGP SIGNATURE-----
iQJDBAABCgAtFiEEn9UcU+C1Yxj9lZw9I9DQutE9ekMFAl/Uxq8PHG1hekBrZXJu
ZWwub3JnAAoJECPQ0LrRPXpDoW0P/0ZMDvFPxrfnJD46exUgUOPuuFF8jZxAlxD8
7UExqar7u6yX7bbq394jPgtOOxldDagfCx/jCXgb9ja7DK5EHKRcrfjaDT8knHi2
Keg5RaRMRi9TVltvWQTxAkXwSv0Atl881qqsndPeZCez0GNZp+HB34s+rNkZwBOu
MBrWihMQOSv5QE6milsNc7HXLSHM1eLZ7Y2XgumNtKrIGEX9yZI7qwdMofwP8Za3
ayMOvc1WAWaTJI7Mg5ac1yTCVbqLmRHhCtws6c6DMgaRu6SI0itmbpQzkDuJJIe3
k9h4KQPaKAFcQsoo3GV0MKTMm63eq82XT3CAdv+htYRY1z95D2+nzNK+mJtsGptX
gJ2zeJkUb4u+yVtNguL9qjo5ssCXV/6IybJxv6baaEFnSwQMUwqa066NdxmtqfIe
1BOWnc153a7SRbQ34M9/llje+v8YJbueGMS2RFR2LQ6IjjpaHsXh+YCZokfA/kdk
zGbOUD5WWFtFD1T3UoaJ4gFt+pzHjNqym4CcEj4S1Vf5y+POUkNmC+GYK+xfm2Fp
WJMbdIUxJhHFRD9L1ShtfAVUSbp712VOOdILp9rYAkOdqfb51BVUiMUP++s2dGp1
ZIT78qt7kTKT1CxbDdFAjzsi7RoMqdSGYgKmG4sVprELeZnFwq47nBkBr8XEQ1TT
0ccEUOY8
=7Z24
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates for 5.11 from Marc Zyngier:
- Preliminary support for managed interrupts on platform devices
- Correctly identify allocation of MSIs proxyied by another device
- Remove the fasteoi IPI flow which has been proved useless
- Generalise the Ocelot support to new SoCs
- Improve GICv4.1 vcpu entry, matching the corresponding KVM optimisation
- Work around spurious interrupts on Qualcomm PDC
- Random fixes and cleanups
Link: https://lore.kernel.org/r/20201212135626.1479884-1-maz@kernel.org
handle_percpu_devid_fasteoi_ipi() has no more users, and
handle_percpu_devid_irq() can do all that it was supposed to do. Get rid of
it.
This reverts commit c5e5ec033c.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201109094121.29975-6-valentin.schneider@arm.com
An interrupt that is disabled/masked but set for wakeup may still need to
be able to wake up the system from sleep states like "suspend to RAM".
To that effect, introduce the IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag.
If the irqchip have this flag set, the irq PM code will enable/unmask
the irqs that are marked for wakeup, but that are in a disabled state.
On resume, such irqs will be restored back to their disabled state.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
[maz: commit message fix-up]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/1601267524-20199-4-git-send-email-mkshah@codeaurora.org
In order to avoid compilation errors when a driver references set_handle_irq(),
but that the architecture doesn't select GENERIC_IRQ_MULTI_HANDLER,
add a stub function that will just WARN_ON_ONCE() if ever used.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
[maz: commit message]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200924071754.4509-2-thunder.leizhen@huawei.com
A number of architectures implement IPI statistics directly,
duplicating the core kstat_irqs accounting. As we move IPIs to
being actual IRQs, we would end-up with a confusing display
in /proc/interrupts (where the IPIs would appear twice).
In order to solve this, allow interrupts to be flagged as
"hidden", which excludes them from /proc/interrupts.
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
For irqchips using the fasteoi flow, IPIs are a bit special.
They need to be EOI'd early (before calling the handler), as
funny things may happen in the handler (they do not necessarily
behave like a normal interrupt).
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
John reported that on a RK3288 system the perf per CPU interrupts are all
affine to CPU0 and provided the analysis:
"It looks like what happens is that because the interrupts are not per-CPU
in the hardware, armpmu_request_irq() calls irq_force_affinity() while
the interrupt is deactivated and then request_irq() with IRQF_PERCPU |
IRQF_NOBALANCING.
Now when irq_startup() runs with IRQ_STARTUP_NORMAL, it calls
irq_setup_affinity() which returns early because IRQF_PERCPU and
IRQF_NOBALANCING are set, leaving the interrupt on its original CPU."
This was broken by the recent commit which blocked interrupt affinity
setting in hardware before activation of the interrupt. While this works in
general, it does not work for this particular case. As contrary to the
initial analysis not all interrupt chip drivers implement an activate
callback, the safe cure is to make the deferred interrupt affinity setting
at activation time opt-in.
Implement the necessary core logic and make the two irqchip implementations
for which this is required opt-in. In hindsight this would have been the
right thing to do, but ...
Fixes: baedb87d1b ("genirq/affinity: Handle affinity setting on inactive interrupts correctly")
Reported-by: John Keeping <john@metanate.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/87blk4tzgm.fsf@nanos.tec.linutronix.de
- Remove setup_irq() and remove_irq(). All users have been converted so
remove them before new users surface.
- A set of bugfixes for various interrupt chip drivers
- Add a few missing static attributes to address sparse warnings.
-----BEGIN PGP SIGNATURE-----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=jaX5
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2020-04-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes/updates for the interrupt subsystem:
- Remove setup_irq() and remove_irq(). All users have been converted
so remove them before new users surface.
- A set of bugfixes for various interrupt chip drivers
- Add a few missing static attributes to address sparse warnings"
* tag 'irq-urgent-2020-04-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/irq-bcm7038-l1: Make bcm7038_l1_of_init() static
irqchip/irq-mvebu-icu: Make legacy_bindings static
irqchip/meson-gpio: Fix HARDIRQ-safe -> HARDIRQ-unsafe lock order
irqchip/sifive-plic: Fix maximum priority threshold value
irqchip/ti-sci-inta: Fix processing of masked irqs
irqchip/mbigen: Free msi_desc on device teardown
irqchip/gic-v4.1: Update effective affinity of virtual SGIs
irqchip/gic-v4.1: Add support for VPENDBASER's Dirty+Valid signaling
genirq: Remove setup_irq() and remove_irq()
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
In general calling generic_handle_irq() with interrupts disabled from non
interrupt context is harmless. For some interrupt controllers like the x86
trainwrecks this is outright dangerous as it might corrupt state if an
interrupt affinity change is pending.
Add infrastructure which allows to mark interrupts as unsafe and catch such
usage in generic_handle_irq().
Reported-by: sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lkml.kernel.org/r/20200306130623.590923677@linutronix.de
Evan tracked down a subtle race between the update of the MSI message and
the device raising an interrupt internally on PCI devices which do not
support MSI masking. The update of the MSI message is non-atomic and
consists of either 2 or 3 sequential 32bit wide writes to the PCI config
space.
- Write address low 32bits
- Write address high 32bits (If supported by device)
- Write data
When an interrupt is migrated then both address and data might change, so
the kernel attempts to mask the MSI interrupt first. But for MSI masking is
optional, so there exist devices which do not provide it. That means that
if the device raises an interrupt internally between the writes then a MSI
message is sent built from half updated state.
On x86 this can lead to spurious interrupts on the wrong interrupt
vector when the affinity setting changes both address and data. As a
consequence the device interrupt can be lost causing the device to
become stuck or malfunctioning.
Evan tried to handle that by disabling MSI accross an MSI message
update. That's not feasible because disabling MSI has issues on its own:
If MSI is disabled the PCI device is routing an interrupt to the legacy
INTx mechanism. The INTx delivery can be disabled, but the disablement is
not working on all devices.
Some devices lose interrupts when both MSI and INTx delivery are disabled.
Another way to solve this would be to enforce the allocation of the same
vector on all CPUs in the system for this kind of screwed devices. That
could be done, but it would bring back the vector space exhaustion problems
which got solved a few years ago.
Fortunately the high address (if supported by the device) is only relevant
when X2APIC is enabled which implies interrupt remapping. In the interrupt
remapping case the affinity setting is happening at the interrupt remapping
unit and the PCI MSI message is programmed only once when the PCI device is
initialized.
That makes it possible to solve it with a two step update:
1) Target the MSI msg to the new vector on the current target CPU
2) Target the MSI msg to the new vector on the new target CPU
In both cases writing the MSI message is only changing a single 32bit word
which prevents the issue of inconsistency.
After writing the final destination it is necessary to check whether the
device issued an interrupt while the intermediate state #1 (new vector,
current CPU) was in effect.
This is possible because the affinity change is always happening on the
current target CPU. The code runs with interrupts disabled, so the
interrupt can be detected by checking the IRR of the local APIC. If the
vector is pending in the IRR then the interrupt is retriggered on the new
target CPU by sending an IPI for the associated vector on the target CPU.
This can cause spurious interrupts on both the local and the new target
CPU.
1) If the new vector is not in use on the local CPU and the device
affected by the affinity change raised an interrupt during the
transitional state (step #1 above) then interrupt entry code will
ignore that spurious interrupt. The vector is marked so that the
'No irq handler for vector' warning is supressed once.
2) If the new vector is in use already on the local CPU then the IRR check
might see an pending interrupt from the device which is using this
vector. The IPI to the new target CPU will then invoke the handler of
the device, which got the affinity change, even if that device did not
issue an interrupt
3) If the new vector is in use already on the local CPU and the device
affected by the affinity change raised an interrupt during the
transitional state (step #1 above) then the handler of the device which
uses that vector on the local CPU will be invoked.
expose issues in device driver interrupt handlers which are not prepared to
handle a spurious interrupt correctly. This not a regression, it's just
exposing something which was already broken as spurious interrupts can
happen for a lot of reasons and all driver handlers need to be able to deal
with them.
Reported-by: Evan Green <evgreen@chromium.org>
Debugged-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Evan Green <evgreen@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87imkr4s7n.fsf@nanos.tec.linutronix.de
On certain QTI chipsets some GPIOs are direct-connect interrupts to the
GIC to be used as regular interrupt lines. When the GPIOs are not used
for interrupt generation the interrupt line is disabled. But disabling
the interrupt at GIC does not prevent the interrupt to be reported as
pending at GIC_ISPEND. Later, when drivers call enable_irq() on the
interrupt, an unwanted interrupt occurs.
Introduce get and set methods for irqchip's parent to clear it's pending
irq state. This then can be invoked by the GPIO interrupt controller on
the parents in it hierarchy to clear the interrupt before enabling the
interrupt.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1573855915-9841-7-git-send-email-ilina@codeaurora.org
[updated commit text and minor code fixes]
Introduce irq_chip_{request,release}_resource_parent() apis so
that these can be used in hierarchical irqchips.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Core changes:
- The big change this time around is the irqchip handling in
the qualcomm pin controllers, closely coupled with the
gpiochip. This rework, in a classic fall-between-the-chairs
fashion has been sidestepped for too long. The Qualcomm
IRQchips using the SPMI and SSBI transport mechanisms have
been rewritten to use hierarchical irqchip. This creates
the base from which I intend to gradually pull support for
hierarchical irqchips into the gpiolib irqchip helpers to
cut down on duplicate code. We have too many hacks in the
kernel because people have been working around the missing
hierarchical irqchip for years, and once it was there,
noone understood it for a while. We are now slowly adapting
to using it. This is why this pull requests include changes
to MFD, SPMI, IRQchip core and some ARM Device Trees
pertaining to the Qualcomm chip family. Since Qualcomm have
so many chips and such large deployments it is paramount
that this platform gets this right, and now it (hopefully)
does.
- Core support for pull-up and pull-down configuration, also
from the device tree. When a simple GPIO chip support a
"off or on" pull-up or pull-down resistor, we provide a
way to set this up using machine descriptors or device tree.
If more elaborate control of pull up/down (such as
resistance shunt setting) is required, drivers should be
phased over to use pin control. We do not yet provide a
userspace ABI for this pull up-down setting but I suspect
the makers are going to ask for it soon enough. PCA953x
is the first user of this new API.
- The GPIO mockup driver has been revamped after some
discussion improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for
both testing and virtual prototyping, e.g. when you do
not yet have a GPIO expander to play with but really
want to get something to develop code around before
hardware is available. It's neat. The blackbox testing
usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating
flags.
- A new device core helper for devm_platform_ioremap_resource()
is funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped
I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum
driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers.
-----BEGIN PGP SIGNATURE-----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=VoVC
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.1 cycle:
Core changes:
- The big change this time around is the irqchip handling in the
qualcomm pin controllers, closely coupled with the gpiochip. This
rework, in a classic fall-between-the-chairs fashion has been
sidestepped for too long.
The Qualcomm IRQchips using the SPMI and SSBI transport mechanisms
have been rewritten to use hierarchical irqchip. This creates the
base from which I intend to gradually pull support for hierarchical
irqchips into the gpiolib irqchip helpers to cut down on duplicate
code.
We have too many hacks in the kernel because people have been
working around the missing hierarchical irqchip for years, and once
it was there, noone understood it for a while. We are now slowly
adapting to using it.
This is why this pull requests include changes to MFD, SPMI,
IRQchip core and some ARM Device Trees pertaining to the Qualcomm
chip family. Since Qualcomm have so many chips and such large
deployments it is paramount that this platform gets this right, and
now it (hopefully) does.
- Core support for pull-up and pull-down configuration, also from the
device tree. When a simple GPIO chip supports an "off or on" pull-up
or pull-down resistor, we provide a way to set this up using
machine descriptors or device tree.
If more elaborate control of pull up/down (such as resistance shunt
setting) is required, drivers should be phased over to use pin
control. We do not yet provide a userspace ABI for this pull
up-down setting but I suspect the makers are going to ask for it
soon enough. PCA953x is the first user of this new API.
- The GPIO mockup driver has been revamped after some discussion
improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for both testing
and virtual prototyping, e.g. when you do not yet have a GPIO
expander to play with but really want to get something to develop
code around before hardware is available. It's neat. The blackbox
testing usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating flags.
- A new device core helper for devm_platform_ioremap_resource() is
funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers"
* tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (110 commits)
gpio: gpio-omap: fix level interrupt idling
gpio: amd-fch: Set proper output level for direction_output
x86: apuv2: remove unused variable
gpio: pca953x: Use PCA_LATCH_INT
platform/x86: fix PCENGINES_APU2 Kconfig warning
gpio: pca953x: Fix dereference of irq data in shutdown
gpio: amd-fch: Fix type error found by sparse
gpio: amd-fch: Drop const from resource
gpio: mxc: add check to return defer probe if clock tree NOT ready
gpio: ftgpio: Register per-instance irqchip
gpio: ixp4xx: Add DT bindings
x86: pcengines apuv2 gpio/leds/keys platform driver
gpio: AMD G-Series PCH gpio driver
drivers: depend on HAS_IOMEM for devm_platform_ioremap_resource()
gpio: tqmx86: Set proper output level for direction_output
gpio: sprd: Change to use SoC compatible string
gpio: sprd: Use SoC compatible string instead of wildcard string
gpio: of: Handle both enable-gpio{,s}
gpio: of: Restrict enable-gpio quirk to regulator-gpio
gpio: davinci: use devm_platform_ioremap_resource()
...
The hierarchical irqchip never before ran into a situation
where the parent is not "simple", i.e. does not implement
.irq_ack() and .irq_mask() like most, but the qcom-pm8xxx.c
happens to implement only .irq_mask_ack().
Since we want to make ssbi-gpio a hierarchical child of this
irqchip, it must *also* only implement .irq_mask_ack()
and call down to the parent, and for this we of course
need irq_chip_mask_ack_parent().
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Provide flow handlers that are NMI safe for interrupts and percpu_devid
interrupts.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add functionality to allocate interrupt lines that will deliver IRQs
as Non-Maskable Interrupts. These allocations are only successful if
the irqchip provides the necessary support and allows NMI delivery for the
interrupt line.
Interrupt lines allocated for NMI delivery must be enabled/disabled through
enable_nmi/disable_nmi_nosync to keep their state consistent.
To treat a PERCPU IRQ as NMI, the interrupt must not be shared nor threaded,
the irqchip directly managing the IRQ must be the root irqchip and the
irqchip cannot be behind a slow bus.
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The interrupt affinity management uses straight cpumask pointers to convey
the automatically assigned affinity masks for managed interrupts. The core
interrupt descriptor allocation also decides based on the pointer being non
NULL whether an interrupt is managed or not.
Devices which use managed interrupts usually have two classes of
interrupts:
- Interrupts for multiple device queues
- Interrupts for general device management
Currently both classes are treated the same way, i.e. as managed
interrupts. The general interrupts get the default affinity mask assigned
while the device queue interrupts are spread out over the possible CPUs.
Treating the general interrupts as managed is both a limitation and under
certain circumstances a bug. Assume the following situation:
default_irq_affinity = 4..7
So if CPUs 4-7 are offlined, then the core code will shut down the device
management interrupts because the last CPU in their affinity mask went
offline.
It's also a limitation because it's desired to allow manual placement of
the general device interrupts for various reasons. If they are marked
managed then the interrupt affinity setting from both user and kernel space
is disabled.
To remedy that situation it's required to convey more information than the
cpumasks through various interfaces related to interrupt descriptor
allocation.
Instead of adding yet another argument, create a new data structure
'irq_affinity_desc' which for now just contains the cpumask. This struct
can be expanded to convey auxilliary information in the next step.
No functional change, just preparatory work.
[ tglx: Simplified logic and clarified changelog ]
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dou Liyang <douliyangs@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-pci@vger.kernel.org
Cc: kashyap.desai@broadcom.com
Cc: shivasharan.srikanteshwara@broadcom.com
Cc: sumit.saxena@broadcom.com
Cc: ming.lei@redhat.com
Cc: hch@lst.de
Cc: douliyang1@huawei.com
Link: https://lkml.kernel.org/r/20181204155122.6327-2-douliyangs@gmail.com
Linux spreads out the non managed interrupt across the possible target CPUs
to avoid vector space exhaustion.
Managed interrupts are treated differently, as for them the vectors are
reserved (with guarantee) when the interrupt descriptors are initialized.
When the interrupt is requested a real vector is assigned. The assignment
logic uses the first CPU in the affinity mask for assignment. If the
interrupt has more than one CPU in the affinity mask, which happens when a
multi queue device has less queues than CPUs, then doing the same search as
for non managed interrupts makes sense as it puts the interrupt on the
least interrupt plagued CPU. For single CPU affine vectors that's obviously
a NOOP.
Restructre the matrix allocation code so it does the 'best CPU' search, add
the sanity check for an empty affinity mask and adapt the call site in the
x86 vector management code.
[ tglx: Added the empty mask check to the core and improved change log ]
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/20180908175838.14450-2-dou_liyang@163.com
Debug is missing the IRQCHIP_SUPPORTS_LEVEL_MSI debug entry, making debugfs
slightly less useful.
Take this opportunity to also add a missing comment in the definition of
IRQCHIP_SUPPORTS_LEVEL_MSI.
Fixes: 6988e0e0d2 ("genirq/msi: Limit level-triggered MSI to platform devices")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Link: https://lkml.kernel.org/r/20180622095254.5906-2-marc.zyngier@arm.com
Pull x86 updates and fixes from Thomas Gleixner:
- Fix the (late) fallout from the vector management rework causing
hlist corruption and irq descriptor reference leaks caused by a
missing sanity check.
The straight forward fix triggered another long standing issue to
surface. The pre rework code hid the issue due to being way slower,
but now the chance that user space sees an EBUSY error return when
updating irq affinities is way higher, though quite a bunch of
userspace tools do not handle it properly despite the fact that EBUSY
could be returned for at least 10 years.
It turned out that the EBUSY return can be avoided completely by
utilizing the existing delayed affinity update mechanism for irq
remapped scenarios as well. That's a bit more error handling in the
kernel, but avoids fruitless fingerpointing discussions with tool
developers.
- Decouple PHYSICAL_MASK from AMD SME as its going to be required for
the upcoming Intel memory encryption support as well.
- Handle legacy device ACPI detection properly for newer platforms
- Fix the wrong argument ordering in the vector allocation tracepoint
- Simplify the IDT setup code for the APIC=n case
- Use the proper string helpers in the MTRR code
- Remove a stale unused VDSO source file
- Convert the microcode update lock to a raw spinlock as its used in
atomic context.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel_rdt: Enable CMT and MBM on new Skylake stepping
x86/apic/vector: Print APIC control bits in debugfs
genirq/affinity: Defer affinity setting if irq chip is busy
x86/platform/uv: Use apic_ack_irq()
x86/ioapic: Use apic_ack_irq()
irq_remapping: Use apic_ack_irq()
x86/apic: Provide apic_ack_irq()
genirq/migration: Avoid out of line call if pending is not set
genirq/generic_pending: Do not lose pending affinity update
x86/apic/vector: Prevent hlist corruption and leaks
x86/vector: Fix the args of vector_alloc tracepoint
x86/idt: Simplify the idt_setup_apic_and_irq_gates()
x86/platform/uv: Remove extra parentheses
x86/mm: Decouple dynamic __PHYSICAL_MASK from AMD SME
x86: Mark native_set_p4d() as __always_inline
x86/microcode: Make the late update update_lock a raw lock for RT
x86/mtrr: Convert to use strncpy_from_user() helper
x86/mtrr: Convert to use match_string() helper
x86/vdso: Remove unused file
x86/i8237: Register device based on FADT legacy boot flag
The upcoming fix for the -EBUSY return from affinity settings requires to
use the irq_move_irq() functionality even on irq remapped interrupts. To
avoid the out of line call, move the check for the pending bit into an
inline helper.
Preparatory change for the real fix. No functional change.
Fixes: dccfe3147b ("x86/vector: Simplify vector move cleanup")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <liu.song.a23@gmail.com>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: stable@vger.kernel.org
Cc: Mike Travis <mike.travis@hpe.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Link: https://lkml.kernel.org/r/20180604162224.471925894@linutronix.de
Nobody would be insane enough to try and use level triggered
MSIs on PCI, but let's make sure it doesn't happen. Also,
let's mandate that the irqchip backing the platform MSI domain
is providing the IRQCHIP_SUPPORTS_LEVEL_MSI flag.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lkml.kernel.org/r/20180508121438.11301-3-marc.zyngier@arm.com
<linux/irq.h> does not use nor need several of its #included files,
so drop those header files from irq.h.
<linux/irq.h> is currently #included in around 1135 C source files
(oops, I didn't count other header files that #include it), making it
the 29th most-used header file.
Build tested on i386 and x86_64 * (allnoconfig, tiny.config, defconfig,
allyesconfig, and allmodconfig) and x64_64 allmodconfig + SMP=disabled.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/02745e91-c117-74b5-d043-dceb3d4bb4e0@infradead.org
Add a new flag to mark interrupts which can use reservation mode. This is
going to be used in subsequent patches to disable reservation mode for a
certain class of MSI devices.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexandru Chirvasitu <achirvasub@gmail.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
- A core irq fix for legacy cases where the irq trigger is not reported
by firmware
- A couple of GICv3/4 fixes (Kconfig, of-node refcount, error handling)
- Trivial pr_err fixes
-----BEGIN PGP SIGNATURE-----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=/8DQ
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates for 4.15, take #4 from Marc Zyngier
- A core irq fix for legacy cases where the irq trigger is not reported
by firmware
- A couple of GICv3/4 fixes (Kconfig, of-node refcount, error handling)
- Trivial pr_err fixes
Pull irq core updates from Thomas Gleixner:
"A rather large update for the interrupt core code and the irq chip drivers:
- Add a new bitmap matrix allocator and supporting changes, which is
used to replace the x86 vector allocator which comes with separate
pull request. This allows to replace the convoluted nested loop
allocation function in x86 with a facility which supports the
recently added property of managed interrupts proper and allows to
switch to a best effort vector reservation scheme, which addresses
problems with vector exhaustion.
- A large update to the ARM GIC-V3-ITS driver adding support for
range selectors.
- New interrupt controllers:
- Meson and Meson8 GPIO
- BCM7271 L2
- Socionext EXIU
If you expected that this will stop at some point, I have to
disappoint you. There are new ones posted already. Sigh!
- STM32 interrupt controller support for new platforms.
- A pile of fixes, cleanups and updates to the MIPS GIC driver
- The usual small fixes, cleanups and updates all over the place.
Most visible one is to move the irq chip drivers Kconfig switches
into a separate Kconfig menu"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
genirq: Fix type of shifting literal 1 in __setup_irq()
irqdomain: Drop pointless NULL check in virq_debug_show_one
genirq/proc: Return proper error code when irq_set_affinity() fails
irq/work: Use llist_for_each_entry_safe
irqchip: mips-gic: Print warning if inherited GIC base is used
irqchip/mips-gic: Add pr_fmt and reword pr_* messages
irqchip/stm32: Move the wakeup on interrupt mask
irqchip/stm32: Fix initial values
irqchip/stm32: Add stm32h7 support
dt-bindings/interrupt-controllers: Add compatible string for stm32h7
irqchip/stm32: Add multi-bank management
irqchip/stm32: Select GENERIC_IRQ_CHIP
irqchip/exiu: Add support for Socionext Synquacer EXIU controller
dt-bindings: Add description of Socionext EXIU interrupt controller
irqchip/gic-v3-its: Fix VPE activate callback return value
irqchip: mips-gic: Make IPI bitmaps static
irqchip: mips-gic: Share register writes in gic_set_type()
irqchip: mips-gic: Remove gic_vpes variable
irqchip: mips-gic: Use num_possible_cpus() to reserve IPIs
irqchip: mips-gic: Configure EIC when CPUs come online
...
When requesting a shared interrupt, we assume that the firmware
support code (DT or ACPI) has called irqd_set_trigger_type
already, so that we can retrieve it and check that the requester
is being reasonnable.
Unfortunately, we still have non-DT, non-ACPI systems around,
and these guys won't call irqd_set_trigger_type before requesting
the interrupt. The consequence is that we fail the request that
would have worked before.
We can either chase all these use cases (boring), or address it
in core code (easier). Let's have a per-irq_desc flag that
indicates whether irqd_set_trigger_type has been called, and
let's just check it when checking for a shared interrupt.
If it hasn't been set, just take whatever the interrupt
requester asks.
Fixes: 382bd4de61 ("genirq: Use irqd_get_trigger_type to compare the trigger type for shared IRQs")
Cc: stable@vger.kernel.org
Reported-and-tested-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Any usage of the irq_gc_mask_disable_reg_and_ack() function has
been replaced with the desired functionality.
The incorrect and ambiguously named function is removed here to
prevent accidental misuse.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The irq_gc_mask_disable_reg_and_ack() function name implies that it
provides the combined functions of irq_gc_mask_disable_reg() and
irq_gc_ack(). However, the implementation does not actually do
that since it writes the mask instead of the disable register. It
also does not maintain the mask cache which makes it inappropriate
to use with other masking functions.
In addition, commit 659fb32d1b ("genirq: replace irq_gc_ack() with
{set,clr}_bit variants (fwd)") effectively renamed irq_gc_ack() to
irq_gc_ack_set_bit() so this function probably should have also been
renamed at that time.
The generic chip code currently provides three functions for use
with the irq_mask member of the irq_chip structure and two functions
for use with the irq_ack member of the irq_chip structure. These
functions could be combined into six functions for use with the
irq_mask_ack member of the irq_chip structure. However, since only
one of the combinations is currently used, only the function
irq_gc_mask_disable_and_ack_set() is added by this commit.
The '_reg' and '_bit' portions of the base function name were left
out of the new combined function name in an attempt to keep the
function name length manageable with the 80 character source code
line length while still allowing the distinct aspects of each
combination to be captured by the name.
If other combinations are desired in the future please add them to
the irq generic chip library at that time.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Implement the infrastructure for a simple bitmap based allocator, which
will replace the x86 vector allocator. It's in the core code as other
architectures might be able to reuse/extend it. For now it only implements
allocations for single CPUs, but it's simple to add multi CPU allocation
support if required.
The concept is rather simple:
Global information:
system_vector bitmap
global accounting
PerCPU information:
allocation bitmap
managed allocation bitmap
local accounting
The system vector bitmap is used to exclude vectors system wide from the
allocation space.
The allocation bitmap is used to keep track of per cpu used vectors.
The managed allocation bitmap is used to reserve vectors for managed
interrupts.
When a regular (non managed) interrupt allocation happens then the
following rule applies:
tmpmap = system_map | alloc_map | managed_map
find_zero_bit(tmpmap)
Oring the bitmaps together gives the real available space. The same rule
applies for reserving a managed interrupt vector. But contrary to the
regular interrupts the reservation only marks the bit in the managed map
and therefor excludes it from the regular allocations. The managed map is
only cleaned out when the a managed interrupt is completely released and it
stays alive accross CPU offline/online operations.
For managed interrupt allocations the rule is:
tmpmap = managed_map & ~alloc_map
find_first_bit(tmpmap)
This returns the first bit which is in the managed map, but not yet
allocated in the allocation map. The allocation marks it in the allocation
map and hands it back to the caller for use.
The rest of the code are helper functions to handle the various
requirements and the accounting which are necessary to replace the x86
vector allocation code. The result is a single patch as the evolution of
this infrastructure cannot be represented in bits and pieces.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213153.185437174@linutronix.de
This reverts commit 74def747bc.
The change to the helper function is only correct for the /proc/irq/
readout usage, but breaks the existing x86 usage of that function.
Reported-by: Yanko Kaneti <yaneti@declera.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Follow-on patch for gpio-thunderx uses a irqdomain hierarchy which
requires slightly different flow handlers, add them to chip.c which
contains most of the other flow handlers. Make these conditionally
compiled based on CONFIG_IRQ_FASTEOI_HIERARCHY_HANDLERS.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Link: http://lkml.kernel.org/r/1503017616-3252-3-git-send-email-david.daney@cavium.com
Just because CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK is selected
doesn't mean that all the interrupts are using the effective
affinity mask. For a number of them, this mask is likely to
be empty.
In order to deal with this, let's restrict the use of the
effective affinity mask to these interrupts that have a non empty
effective affinity.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: http://lkml.kernel.org/r/20170818083925.10108-2-marc.zyngier@arm.com
That commit was part of the changes moving x86 to the generic CPU hotplug
interrupt migration code. The force flag was required on x86 before the
hierarchical irqdomain rework, but invoking set_affinity() with force=true
stayed and had no side effects.
At some point in the past, the force flag got repurposed to support the
exynos timer interrupt affinity setting to a not yet online CPU, so the
interrupt controller callback does not verify the supplied affinity mask
against cpu_online_mask.
Setting the flag in the CPU hotplug code causes the cpu online masking to
be blocked on these irq controllers and results in potentially affining an
interrupt to the CPU which is unplugged, i.e. instead of moving it away,
it's just reassigned to it.
As the force flags is not longer needed on x86, it's safe to revert that
patch so the ARM irqchips which use the force flag work again.
Add comments to that effect, so this won't happen again.
Note: The online mask handling should be done in the generic code and the
force flag and the masking in the irq chips removed all together, but
that's not a change possible for 4.13.
Fixes: 77f85e66aa ("genirq/cpuhotplug: Set force affinity flag on hotplug migration")
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: LAK <linux-arm-kernel@lists.infradead.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1707271217590.3109@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner
Linus Torvalds
Marc Zyngier
Ingo Molnar
Hans de Goede
Valentin Schneider
Maulik Shah
Zhen Lei
Gustavo A. R. Silva
afzal mohammed
Lokesh Vutla
Peter Xu
Linus Walleij
Julien Thierry
Dou Liyang
Dou Liyang
Marc Zyngier
Palmer Dabbelt
Randy Dunlap
Greg Kroah-Hartman
Doug Berger
David Daney