Adds DMA Engine framework support into RapidIO subsystem.
Uses DMA Engine DMA_SLAVE interface to generate data transfers to/from
remote RapidIO target devices.
Introduces RapidIO-specific wrapper for prep_slave_sg() interface with an
extra parameter to pass target specific information.
Uses scatterlist to describe local data buffer. Address flat data buffer
on a remote side.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a possible problem with mport registration left non-cleared after
fsl_rio_setup() exits on link error. Abort mport initialization if
registration failed.
This patch is applicable to 2.6.39-rc1 only. The problem does not exist
for earlier versions.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removes resource reservation from the common sybsystem initialization code
and make it part of mport driver initialization. This resolves conflict
with resource reservation by device specific mport drivers.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changes mport ID and host destination ID assignment to implement unified
method common to all mport drivers. Makes "riohdid=" kernel command line
parameter common for all architectures with support for more that one host
destination ID assignment.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Subsystem initialization sequence modified to support presence of multiple
RapidIO controllers in the system. The new sequence is compatible with
initialization of PCI devices.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This set of patches eliminates RapidIO dependency on PowerPC architecture
and makes it available to other architectures (x86 and MIPS). It also
enables support of new platform independent RapidIO controllers such as
PCI-to-SRIO and PCI Express-to-SRIO.
This patch:
Extend number of mport callback functions to eliminate direct linking of
architecture specific mport operations.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add definition of the unique device identifier field in the component tag.
RIO_CTAG_UDEVID does not take all 32 bits of the component tag value to
allow future extensions to the component tag use.
Selected size of the RIO_CTAG_UDEVID field (17 bits) is sufficient to
accommodate maximum number of endpoints in large RIO network (16-bit id)
plus switches.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change code to use one storage location common for switches and endpoints.
This eliminates unnecessary device type checks during basic access
operations. Logic that assigns destid to RIO devices stays unchanged - as
before, switches use an associated destid because they do not have their
own.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The size calculation is done incorrectly here because it should include
both the start and end (end - start + 1). It's easiest to just use
resource_size() which does the right thing.
I was worried there was something non-standard going on because the
printk() subtracts "end - 1", but the rest of the file uses the normal
resource size calculations. This function is only called from
fsl_rio_setup() in arch/powerpc/sysdev/fsl_rio.c and the calculation
there is also:
port->iores.start = law_start;
port->iores.end = law_start + law_size - 1;
So I think this is the correct fix.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RapidIO spec v.2.1 adds Idle Sequence 2 into LP-Serial Physical Layer.
The fix ensures that corresponding bits are not corrupted during error
handling.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Detects RIO link to the already enumerated device and properly sets links
between device objects. Changes to the enumeration/discovery logic:
1. Use Master Enable bit to signal end of the enumeration - agents may
start their discovery process as soon as they see this bit set
(Component Tag register was used before for this purpose).
2. Enumerator sets Component Tag (!= 0) immediately during device
setup. This allows to identify the device if the redundant route
exists in a RIO system.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add explicit device access check before performing device enumeration.
This gives a chance to clear possible link error conditions by issuing
safe maintenance read request(s).
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add check for access to port-write (PW) message source device before
processing the PW message. If source RIO device is not available (power
down or RIO link failure) trace back to a last available switch/port on
the PW message route and service failure at that point.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default error-stopped state handler provides recovery mechanism as
defined by RIO specification.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bunch of new rapidio kernel-doc warnings:
Warning(include/linux/rio.h:123): No description found for parameter 'comp_tag'
Warning(include/linux/rio.h:123): No description found for parameter 'phys_efptr'
Warning(include/linux/rio.h:123): No description found for parameter 'em_efptr'
Warning(include/linux/rio.h:123): No description found for parameter 'pwcback'
Warning(include/linux/rio.h:247): No description found for parameter 'set_domain'
Warning(include/linux/rio.h:247): No description found for parameter 'get_domain'
Warning(drivers/rapidio/rio-scan.c:1133): No description found for parameter 'rdev'
Warning(drivers/rapidio/rio-scan.c:1133): Excess function parameter 'port' description in 'rio_init_em'
Warning(drivers/rapidio/rio.c:349): No description found for parameter 'rdev'
Warning(drivers/rapidio/rio.c:349): Excess function parameter 'mport' description in 'rio_request_inb_pwrite'
Warning(drivers/rapidio/rio.c:393): No description found for parameter 'port'
Warning(drivers/rapidio/rio.c:393): No description found for parameter 'local'
Warning(drivers/rapidio/rio.c:393): No description found for parameter 'destid'
Warning(drivers/rapidio/rio.c:393): No description found for parameter 'hopcount'
Warning(drivers/rapidio/rio.c:393): Excess function parameter 'rdev' description in 'rio_mport_get_physefb'
Warning(drivers/rapidio/rio.c:845): Excess function parameter 'local' description in 'rio_std_route_clr_table'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add RapidIO Port-Write message handling in the context of Error
Management Extensions Specification Rev.1.3.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Tested-by: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Extentions to RapidIO switch support:
1. modify switch route operation declarations to allow using single
switch-specific file for family of switches that share the same route
table operations.
2. add standard route table operations for switches that that support
route table manipulation registers as defined in the Rev.1.3 of RapidIO
specification.
3. add clear-route-table operation for switches
4. add CPSxx and TSIxxx families of RapidIO switches
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Tested-by: Thomas Moll <thomas.moll@sysgo.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
functions calling devinit and called only from devinit
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The RapidIO system size will auto probe in RIO setup. The route table
and rionet_active in rionet.c are changed to be allocated dynamically
according to the size of the system.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
drivers/rapidio/rio.c: In function 'rio_get_asm':
drivers/rapidio/rio.c:413: error: implicit declaration of function 'in_interrupt'
drivers/rapidio/rio.c: In function 'rio_init_mports':
drivers/rapidio/rio.c:480: warning: format '%8.8lx' expects type 'long unsigned int', but argument 2 has type 'resource_size_t'
drivers/rapidio/rio.c:480: warning: format '%8.8lx' expects type 'long unsigned int', but argument 3 has type 'resource_size_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Include fixes for 2.6.14-git11. Should allow to remove sched.h from
module.h on i386, x86_64, arm, ia64, ppc, ppc64, and s390. Probably more
to come since I haven't yet checked the other archs.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Updates the RIO messaging interface to pass a device instance into the
event registeration and callbacks.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds a RapidIO subsystem to the kernel. RIO is a switched fabric interconnect
used in higher-end embedded applications. The curious can look at the specs
over at http://www.rapidio.org
The core code implements enumeration/discovery, management of
devices/resources, and interfaces for RIO drivers.
There's a lot more to do to take advantages of all the hardware features.
However, this should provide a good base for folks with RIO hardware to start
contributing.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Alexandre Bounine
Dan Carpenter
Uwe Kleine-König
Randy Dunlap
Al Viro
Zhang Wei
Kumar Gala
Jörn Engel
Tim Schmielau
Matt Porter