Improve documentation for the (H)SCIF Serial Port Register:
- Make it clear the RTS and CTS lines are active-low,
- Document the bits related to the serial port's clock pin.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace open-coded variants of sci_getreg() by function calls, and drop
intermediate variables where appropriate.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enhance the Renesas SCI UART driver to add support for GPIO-controlled
modem lines (CTS, DSR, DCD, RNG, RTS, DTR), using the serial_mctrl_gpio
helpers.
GPIO-controlled modem lines can be used when dedicated modem lines are
not available. Invalid configurations specifying both GPIO RTS/CTS and
dedicated RTS/CTS are rejected.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Documentation/serial/driver clearly states:
If the port does not support CTS, DCD or DSR, the driver should
indicate that the signal is permanently active.
Hence always set TIOCM_CTS, as we currently don't look at the CTS
hardware line state at all.
FWIW, this fixes the transmit path when hardware-assisted flow control
is enabled, and userspace enables CRTSCTS.
The receive path is still broken, as RTS is never asserted.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vc_deccolm is only set and never read, remove the member from vc_data.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do not do hashtables for unicode fonts since 1995 (1.3.28). So it
is time to remove the second parameter of con_clear_unimap and ignore
the advice from userspace completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Namely convert:
* IS_FG -> con_is_fg
* DO_UPDATE -> con_should_update
* CON_IS_VISIBLE -> con_is_visible
DO_UPDATE was a weird name for a yes/no answer, so the new name is
con_should_update.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Flush the switch cases to be aligned with the switch. Mostly
everything can now fit to the 80-chars terminal.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not opencode max3, use the macro.
Separate commands. Until now, I have not noticed the comma. Make it
one line, one command. And make the code obvious.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The compiler noticed passing structure over stack. Even though rgb is
a small structure, let us define one and pass that over all the
functions wherever needed.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code with T.416 high colors handling is flushed to the right and
hard to read. Move the code to a separate function and remove code
duplication for foreground & background colors.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's a macro accessing and changing some local variables. And the code
uses it without appending semicolon which confuses everybody too.
Switch from this bad guy to a sane standard function.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is never defined. And I spent quite some time looking into the
history and cannot find how this was ever used. Given it was not used
in the history, I doubt it currently works as expected after the years
of changes all over the code.
So kill it.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is always called with 0, so remove the parameter and pass the
default down to scrolldelta without checking.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The compiler complains about variables that are set, but never used:
* intX variables in exar_handle_irq
drivers/tty/serial/8250/8250_port.c:1864:34: warning: variable ‘int3’ set but not used [-Wunused-but-set-variable]
* val variable in pci_quatech_wqopr
drivers/tty/serial/8250/8250_pci.c:1139:10: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
And about a shadow variable:
* tmout in wait_for_xmitr is defined twice with the same type. Both of
them are also initialized before use.
Remove all of them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Matt Schulte <matts@commtech-fastcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq can fail, so we should handle negative value when
returned.
[v2]
platform_get_irq can actually return zero on some platforms. So do not
remove checks for irq == 0 there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert DEBUG_INTR to pr_debug:
* defined semantics (DEBUG, DYNAMIC_DEBUG)
* KERN_DEBUG level instead of KERN_DEFAULT
* emit __func__ and \n
* verified 'fmt' even when !DEBUG
I wonder if anybody ever used that or whether we should just drop the
lines.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hub6 and irqflags from struct old_serial_port are nowhere set. Drop
them from the structure and replace the reads by zeros.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STD_COM_FLAGS is mostly a bad name for what the drivers thinks it is.
Stop using it and pass the flags directly.
cyclades defines it as 0, so we do not assign anything to freshly
tty_port_init'ed structure.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not initialize members of initialized structures to zero. They are
zeroed automatically.
Part of hub6 cleanup series.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ipwireless_get_serial_info, struct serial_struct is memset to 0 and
then some members set to 0 explicitly.
Remove the latter as it is obviously superfluous.
And remove the retinfo check against NULL. copy_to_user will take care
of that.
Part of hub6 cleanup series.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jiri Kosina <jikos@kernel.org>
Acked-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The /dev/ptmx device node is changed to lookup the directory entry "pts"
in the same directory as the /dev/ptmx device node was opened in. If
there is a "pts" entry and that entry is a devpts filesystem /dev/ptmx
uses that filesystem. Otherwise the open of /dev/ptmx fails.
The DEVPTS_MULTIPLE_INSTANCES configuration option is removed, so that
userspace can now safely depend on each mount of devpts creating a new
instance of the filesystem.
Each mount of devpts is now a separate and equal filesystem.
Reserved ttys are now available to all instances of devpts where the
mounter is in the initial mount namespace.
A new vfs helper path_pts is introduced that finds a directory entry
named "pts" in the directory of the passed in path, and changes the
passed in path to point to it. The helper path_pts uses a function
path_parent_directory that was factored out of follow_dotdot.
In the implementation of devpts:
- devpts_mnt is killed as it is no longer meaningful if all mounts of
devpts are equal.
- pts_sb_from_inode is replaced by just inode->i_sb as all cached
inodes in the tty layer are now from the devpts filesystem.
- devpts_add_ref is rolled into the new function devpts_ptmx. And the
unnecessary inode hold is removed.
- devpts_del_ref is renamed devpts_release and reduced to just a
deacrivate_super.
- The newinstance mount option continues to be accepted but is now
ignored.
In devpts_fs.h definitions for when !CONFIG_UNIX98_PTYS are removed as
they are never used.
Documentation/filesystems/devices.txt is updated to describe the current
situation.
This has been verified to work properly on openwrt-15.05, centos5,
centos6, centos7, debian-6.0.2, debian-7.9, debian-8.2, ubuntu-14.04.3,
ubuntu-15.10, fedora23, magia-5, mint-17.3, opensuse-42.1,
slackware-14.1, gentoo-20151225 (13.0?), archlinux-2015-12-01. With the
caveat that on centos6 and on slackware-14.1 that there wind up being
two instances of the devpts filesystem mounted on /dev/pts, the lower
copy does not end up getting used.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Greg KH <greg@kroah.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Cc: Jann Horn <jann@thejh.net>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Florian Weimer <fw@deneb.enyo.de>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch of
long-standing bugs in the tty layer and serial drivers as normal. Full
details in the shortlog.
All of these have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0/oACgkQMUfUDdst+ynzyQCgsa54VNijdAzU6AA5HEfqmf2M
cGMAn1boH7hUWlAbJmzzihx4JASoGjYW
=V5VH
-----END PGP SIGNATURE-----
Merge tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here's the large TTY and Serial driver update for 4.7-rc1.
A few new serial drivers are added here, and Peter has fixed a bunch
of long-standing bugs in the tty layer and serial drivers as normal.
Full details in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (88 commits)
MAINTAINERS: 8250: remove website reference
serial: core: Fix port mutex assert if lockdep disabled
serial: 8250_dw: fix wrong logic in dw8250_check_lcr()
tty: vt, finish looping on duplicate
tty: vt, return error when con_startup fails
QE-UART: add "fsl,t1040-ucc-uart" to of_device_id
serial: mctrl_gpio: Drop support for out1-gpios and out2-gpios
serial: 8250dw: Add device HID for future AMD UART controller
Fix OpenSSH pty regression on close
serial: mctrl_gpio: add IRQ locking
serial: 8250: Integrate Fintek into 8250_base
serial: mps2-uart: add support for early console
serial: mps2-uart: add MPS2 UART driver
dt-bindings: document the MPS2 UART bindings
serial: sirf: Use generic uart-has-rtscts DT property
serial: sirf: Introduce helper variable struct device_node *np
serial: mxs-auart: Use generic uart-has-rtscts DT property
serial: imx: Use generic uart-has-rtscts DT property
doc: DT: Add Generic Serial Device Tree Bindings
serial: 8250: of: Make tegra_serial_handle_break() static
...
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.7. Here's the summary of
the changes:
- ATH79: Support for DTB passuing using the UHI boot protocol
- ATH79: Remove support for builtin DTB.
- ATH79: Add zboot debug serial support.
- ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
and DPT-Module.
- ATH79: Update devicetree clock support for AR9132 and AR9331.
- ATH79: Cleanup the DT code.
- ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
- ATH79: Fix regression in PCI window initialization.
- BCM47xx: Move SPROM driver to drivers/firmware/
- BCM63xx: Enable partition parser in defconfig.
- BMIPS: BMIPS5000 has I cache filing from D cache
- BMIPS: BMIPS: Add cpu-feature-overrides.h
- BMIPS: Add Whirlwind support
- BMIPS: Adjust mips-hpt-frequency for BCM7435
- BMIPS: Remove maxcpus from BCM97435SVMB DTS
- BMIPS: Add missing 7038 L1 register cells to BCM7435
- BMIPS: Various tweaks to initialization code.
- BMIPS: Enable partition parser in defconfig.
- BMIPS: Cache tweaks.
- BMIPS: Add UART, I2C and SATA devices to DT.
- BMIPS: Add BCM6358 and BCM63268support
- BMIPS: Add device tree example for BCM6358.
- BMIPS: Improve Improve BCM6328 and BCM6368 device trees
- Lantiq: Add support for device tree file from boot loader
- Lantiq: Allow build with no built-in DT.
- Loongson 3: Reserve 32MB for RS780E integrated GPU.
- Loongson 3: Fix build error after ld-version.sh modification
- Loongson 3: Move chipset ACPI code from drivers to arch.
- Loongson 3: Speedup irq processing.
- Loongson 3: Add basic Loongson 3A support.
- Loongson 3: Set cache flush handlers to nop.
- Loongson 3: Invalidate special TLBs when needed.
- Loongson 3: Fast TLB refill handler.
- MT7620: Fallback strategy for invalid syscfg0.
- Netlogic: Fix CP0_EBASE redefinition warnings
- Octeon: Initialization fixes
- Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
- Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
- Octeon: Correctly handle endian-swapped initramfs images.
- Octeon: Support CN73xx, CN75xx and CN78xx.
- Octeon: Remove dead code from cvmx-sysinfo.
- Octeon: Extend number of supported CPUs past 32.
- Octeon: Remove some code limiting NR_IRQS to 255.
- Octeon: Simplify octeon_irq_ciu_gpio_set_type.
- Octeon: Mark some functions __init in smp.c
- Octeon: Octeon: Add Octeon III CN7xxx interface detection
- PIC32: Add serial driver and bindings for it.
- PIC32: Add PIC32 deadman timer driver and bindings.
- PIC32: Add PIC32 clock timer driver and bindings.
- Pistachio: Determine SoC revision during boot
- Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
- Sibyte: Strip redundant comments from bcm1480_regs.h.
- Panic immediately if panic_on_oops is set.
- module: fix incorrect IS_ERR_VALUE macro usage.
- module: Make consistent use of pr_*
- Remove no longer needed work_on_cpu() call.
- Remove CONFIG_IPV6_PRIVACY from defconfigs.
- Fix registers of non-crashing CPUs in dumps.
- Handle MIPSisms in new vmcore_elf32_check_arch.
- Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
- Allow RIXI to be used on non-R2 or R6 cores.
- Reserve nosave data for hibernation
- Fix siginfo.h to use strict POSIX types.
- Don't unwind user mode with EVA.
- Fix watchpoint restoration
- Ptrace watchpoints for R6.
- Sync icache when it fills from dcache
- I6400 I-cache fills from dcache.
- Various MSA fixes.
- Cleanup MIPS_CPU_* definitions.
- Signal: Move generic copy_siginfo to signal.h
- Signal: Fix uapi include in exported asm/siginfo.h
- Timer fixes for sake of KVM.
- XPA TLB refill fixes.
- Treat perf counter feature
- Update John Crispin's email address
- Add PIC32 watchdog and bindings.
- Handle R10000 LL/SC bug in set_pte()
- cpufreq: Various fixes for Longson1.
- R6: Fix R2 emulation.
- mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
- ELF: ABI and FP fixes.
- Allow for relocatable kernel and use that to support KASLR.
- Fix CPC_BASE_ADDR mask
- Plenty fo smp-cps, CM, R6 and M6250 fixes.
- Make reset_control_ops const.
- Fix kernel command line handling of leading whitespace.
- Cleanups to cache handling.
- Add brcm, bcm6345-l1-intc device tree bindings.
- Use generic clkdev.h header
- Remove CLK_IS_ROOT usage.
- Misc small cleanups.
- CM: Fix compilation error when !MIPS_CM
- oprofile: Fix a preemption issue
- Detect DSP ASE v3 support:1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
MIPS: pic32mzda: fix getting timer clock rate.
MIPS: ath79: fix regression in PCI window initialization
MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
MIPS: Fix VZ probe gas errors with binutils <2.24
MIPS: perf: Fix I6400 event numbers
MIPS: DEC: Export `ioasic_ssr_lock' to modules
MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
MIPS: CM: Fix compilation error when !MIPS_CM
MIPS: Fix genvdso error on rebuild
USB: ohci-jz4740: Remove obsolete driver
MIPS: JZ4740: Probe OHCI platform device via DT
MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
MIPS: pistachio: Determine SoC revision during boot
MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
MIPS: Prevent "restoration" of MSA context in non-MSA kernels
MIPS: cevt-r4k: Dynamically calculate min_delta_ns
MIPS: malta-time: Take seconds into account
MIPS: malta-time: Start GIC count before syncing to RTC
MIPS: Force CPUs to lose FP context during mode switches
...
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
commit 4047b37122 ("serial: core: Prevent unsafe uart port access,
part 1") added lockdep assertion for port mutex but fails to check
if debug_locks has disabled lockdep (so lock state is no longer
reliable).
Use lockdep_assert_held() instead, which properly checks lockdep
state as well.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cdcea058e5 ("serial: 8250_dw: Avoid serial_outx code duplicate
with new dw8250_check_lcr()") introduce a wrong logic when write val to
LCR reg. When CONFIG_64BIT enabled, __raw_writeq is used unconditionally.
The __raw_readq/__raw_writeq is introduced by commit bca2092d78 ("serial:
8250_dw: Use 64-bit access for OCTEON.") for OCTEON.
So for 64BIT && !PORT_OCTEON, we better to use coincident write function.
Fixes: cdcea058e510("serial: 8250_dw: Avoid serial_outx code duplicate with new dw8250_check_lcr()")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the console is already registered, stop crawling the
registered_con_driver array and return an error immediatelly.
This makes the code more obvious. And we do not need to initialize
retval anymore.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When csw->con_startup() fails in do_register_con_driver, we return no
error (i.e. 0). This was changed back in 2006 by commit 3e795de763.
Before that we used to return -ENODEV.
So fix the return value to be -ENODEV in that case again.
Fixes: 3e795de763 ("VT binding: Add binding/unbinding support for the VT console")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: "Dan Carpenter" <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New bindings use "fsl,t1040-ucc-uart" as the compatible for qe-uart.
So add it.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OUT1 and OUT2 pins present on some legacy UARTs are basically GPIOs.
It doesn't make much sense to emulate GPIOs using other GPIOs, hence
drop support for that.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Richard Genoud <richard.genoud@gmail.com>
Reviewed-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device HID AMDI0020 to match the AMD ACPI Vendor ID (AMDI) as
registered in http://www.uefi.org/acpi_id_list, and the UART
controller on future AMD paltform will use the HID instead of AMD0020.
Signed-off-by: Wang Hongcheng <annie.wang@amd.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OpenSSH expects the (non-blocking) read() of pty master to return
EAGAIN only if it has received all of the slave-side output after
it has received SIGCHLD. This used to work on pre-3.12 kernels.
This fix effectively forces non-blocking read() and poll() to
block for parallel i/o to complete for all ttys. It also unwinds
these changes:
1) f8747d4a46
tty: Fix pty master read() after slave closes
2) 52bce7f8d4
pty, n_tty: Simplify input processing on final close
3) 1a48632ffe
pty: Fix input race when closing
Inspired by analysis and patch from Marc Aurele La France <tsi@tuyoix.net>
Reported-by: Volth <openssh@volth.com>
Reported-by: Marc Aurele La France <tsi@tuyoix.net>
BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=52
BugLink: https://bugzilla.mindrot.org/show_bug.cgi?id=2492
Signed-off-by: Brian Bloniarz <brian.bloniarz@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_handle_cts_change should be called with port->lock held. And for
this to be save you must also disable irqs.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250_fintek driver advertises as the PNP0501 driver; however this
conflicts with the standard 16550A uart PNP0501. The conflict causes
the 8250_fintek driver to load with _every_ PNP0501, but never probe,
and causing the entire 8250 driver stack to unload if the 8250_fintek
driver is unloaded (modprobe doesn't know that 8250_pnp rather than
8250_fintek claimed the resource).
This patch merges the Fintek driver into 8250_base. On autoconfig_16550
the device is probed to verify if it is a FINTEK device or not.
This custom probing can be disabled completely via configuration. When a
Fintek device is not probed it will behave as a standard 16550A device,
with no RS485 capabilities.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support early console for MPS2 UART which can be enabled via
earlycon=mps2,0x40004000
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver adds support to the UART controller found on ARM MPS2
platform.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the SiRF UART driver from using the vendor-specific
"sirf,uart-has-rtscts" to the generic "uart-has-rtscts" DT property, as
documented by the Generic Serial DT Bindings.
The old vendor-specific property is still recognized by the driver for
backwards compatibility, but deprecated.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the Freescale MXS AUART driver from using the vendor-specific
"fsl,uart-has-rtscts" to the generic "uart-has-rtscts" DT property, as
documented by the Generic Serial DT Bindings.
The old vendor-specific property is still recognized by the driver for
backwards compatibility, but it is deprecated.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the Freescale IMX UART driver from using the vendor-specific
"fsl,uart-has-rtscts" to the generic "uart-has-rtscts" DT property, as
documented by the Generic Serial DT Bindings.
The old vendor-specific property is still recognized by the driver for
backwards compatibility, but deprecated.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is not used outside the file, so it can be static.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA completed normally does not require termination; only terminate
paused rx dma stemming from rx dma flush.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using fake IIR values to perform rx dma operations unnecessarily
conflates separate operations, stopping in-progress dma with starting
new dma.
Introduce serial8250_rx_dma_flush() to handle stopping in-progress dma
[omap8250 already has equivalent omap_8250_rx_dma_flush()].
Replace rx_dma(UART_IIR_RX_TIMEOUT) with the equivalent *_rx_dma_flush(),
and rx_dma(0) with the equivalent *_rx_dma(). Handle IIR steering
in the irq handler with handle_rx_dma() helper.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract the operation (restarting new rx dma) performed when error
argument is true.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27c310c5c3 ("serial: 8250_dma: no need to sync RX buffer")
notes the RX DMA buffer is allocated from DMA coherent memory, and
thus does not need sync'd for each transaction. The same is true
for OMAP RX DMA.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 dma support requires the dmaegine driver support terminate.
Query slave caps to determine if necessary commands/properties are
supported; disable dma if not.
Note this means dmaengine driver must support slave caps reporting
as well.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 dma support requires the dmaengine driver support error-free
pause/terminate and better-than-descriptor residue granularity. Query
slave caps to determine if necessary commands/properties are supported;
disable dma if not.
Note this means dmaengine driver must support slave caps reporting
as well.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The local mcr variable is never used in the tegra_uart_set_mctrl()
function, so it should be removed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ->get_char() returns a negative error code and that can mean that
"ch" is uninitialized. The callers of this function expect NO_POLL_CHAR
on error so let's return that.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We reach this point of code after a test of 'info->port.tty->hw_stopped',
we do not need to test for 'info->port.tty' as it is obvious that
info->port.tty is not NULL now, we have already dereferenced it.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function alloc_ctrl_packet() can fail and return NULL. Incase it
fails print an error message and exit.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HIGH_BITS_OFFSET is only used in the serial core; remove from 8250-
specific header.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If !up->dma == F, then up->dma == T and can be elided from the
(up->dma && up->dma->tx_err) sub-expression.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_err is not used other than for boolean evaluation;
substitute the actual operation directly.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Intel Penwell and Tangier the HSU block (3 HSU ports) has a global register
set which is currently not used by the driver. On Tangier it has it's own PCI
device and thus available for enumeration. Since it's not a real HSU port we
just skip it and therefore put a comment in the code why we do so.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to compile module on non-X86 platforms, though COMPILE_TEST
is provided for sake of what it does.
While here, set default to SERIAL_8250 that user doesn't need an explicit
option to be set and hide it from non-expert.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BIT() macro, that is definded in bitops.h, is used in the driver. Include
necessary header for that.
While here, reorder included headers alphabetically.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a special register that shows interrupt status by source. In
particular case the source can be a combination of DMA Tx, DMA Rx, and UART.
Read the register and call the handlers only for sources that request an
interrupt.
Fixes: 6ede6dcd87 ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike Intel Medfield and Tangier platforms DNV uses PCI BAR0 for IO compatible
resources and BAR1 for MMIO. We need latter in a way to support DMA. Introduce
an additional field in the internal structure and pass PCI BAR based on device
ID.
Reported-by: "Lai, Poey Seng" <poey.seng.lai@intel.com>
Fixes: 6ede6dcd87 ("serial: 8250_mid: add support for DMA engine handling from UART MMIO")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bay Trail UART port does not support DCD and DSR lines. The driver
shall report that these signals are permanently active. This patch
is for HSUART enumerated via PCI.
For ACPI, see commit dfd37668ea ("serial: 8250_dw: Fix get_mctrl
behaviour"). The commit also describes the possible issue if these
signals are enabled on a port without these pins.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exposes get_mctrl() function so that it can be overriden with platform
specific implementation.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ifx_spi_complete, 'more' is not initialized. It is set only if the
status is clear and only if the header is parsed OK. If any of those
is not true, 'more' can be used uninitialized in that function later.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every user of default_red, default_grn, and default_blu treats them as
unsigned char. So make it really unsigned char.
And indent the initializers and module_param properly.
This saves ~ 100 bytes of data.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This means all ->con_set_palette have to have the second parameter
const too now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some code in vc_allocate is indented by 4 spaces. It is inside a
condition. Invert the condition and move the code to the first
indentation level (using \tab). And insert some empty lines to have
logical code blocks separated.
Then, instead of freeing in an 'if' false branch, use goto-error
label as fail path.
Maybe better to look at this patch with diff -w -b.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MAX_NR_CONSOLES and MAX_NR_USER_CONSOLES are both 63 since they were
introduced in 1.1.54. And since vc_allocate does:
if (currcons >= MAX_NR_CONSOLES)
return -ENXIO;
if (!vc_cons[currcons].d) {
if (currcons >= MAX_NR_USER_CONSOLES && !capable(CAP_SYS_RESOURCE))
return -EPERM;
}
the second check is pointless. Remove both the check and the macro
MAX_NR_USER_CONSOLES.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the broken serial log when changing the clock source
of uart device. Before disabling the original clock source, this patch
enables the new clock source to protect the clock off state for a split second.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The msm_find_best_baud() function is written with the assumption
that the port->uartclk rate is fixed to a particular rate at boot
time, but now this driver changes that clk rate at runtime when
the baud is changed.
The way the hardware works is that an input clk rate comes from
the clk controller into the uart hw block. That rate is typically
1843200 or 3686400 Hz. That rate can then be divided by an
internal divider in the hw block to achieve a particular baud on
the serial wire. msm_find_best_baud() is looking for that divider
value.
A few things are wrong with the way the code is written. First,
it assumes that the maximum baud that the uart can support if the
clk rate is fixed at boot is 460800, which would correspond to an
input clk rate of 230400 * 16 == 3686400 Hz. Except some devices
have a boot rate of 1843200 Hz or max baud of 115200, so
achieving 230400 on those devices doesn't work at all because we
don't increase the clk rate unless max baud is 460800.
Second, we can't achieve bauds higher than 460800 that require
anything besides a divisor of 1, because we always call
msm_find_best_baud() with a fixed port->uartclk rate that will
eventually be changed after we calculate the divisor. So if we
need to get a baud of 500000, we'll just multiply that by 16 and
hope that the clk can give us 500000 * 16 == 8000000 Hz, which it
typically can't do. To really achieve 500000 baud, we need to get
an input clk rate of 24000000 Hz and then divide that by 3 inside
the uart hardware.
Finally, we return success for bauds even when we can't actually
achieve them. This means that when the user asks for 500000 baud,
we actually get 921600 right now, but the user doesn't know that.
Fix all of this by searching through the divisor and clk rate
space with a combination of clk_round_rate() and baud
calculations, keeping track of the best clk rate and divisor we
find if we can't get an exact match. Typically we can get an
exact match with a divisor of 1, but sometimes we need to keep
track and try more frequencies. On my msm8916 device, this
results in all standard bauds in baud_table being supported
except for 1800, 576000, 1152000, and 4000000.
Fixes: 850b37a71b ("tty: serial: msm: Remove 115.2 Kbps maximum baud rate limitation")
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Cc: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Cristian Prundeanu <cprundea@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable reporting of DSR events (which is named DTR in the registers
because Freescale uses the names as seem from a DCE).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to tty_ioctl(4) (from man-pages 4.04) the rng member only
counts 0->1 transitions. For the other signals (DSR, CD, CTS) both edges
are supposed to be counted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that events that are not handled in the irq function don't
trigger an interrupt.
When the serial port is operated in DTE mode, the events for DCD and RI
events are enabled after a system reset by default.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This gives the irq core a chance to disable the serial interrupt in case
an event isn't cleared in the handler.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When in DTE mode, the bit USR2_RIIN is active low. So invert the logic
accordingly.
Fixes: 90ebc48386 ("serial: imx: repair and complete handshaking")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add __init attribute on a function that is only called from other __init
functions and that is not inlined, at least with gcc version 4.8.4 on an
x86 machine with allyesconfig. Currently, the function is put in the
.text.unlikely segment. Declaring it as __init will cause it to be put in
the .init.text and to disappear after initialization.
The result of objdump -x on the function before the change is as follows:
000000000000014c l F .text.unlikely 0000000000000a2e init_r_port
And after the change it is as follows:
0000000000000000 l F .init.text 0000000000000a29 init_r_port
Done with the help of Coccinelle. The semantic patch checks for local
static non-init functions that are called from an __init function and are
not called from any other function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alphascale ASM9260 uart IP has some common registers with
Freescale STMP37XX. This patch provide changes which
allow to reuse mxs-auart.c code for ASM9260.
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SC16is7xx has feature for auto hardware flow control using RTS/CTS,
so we don't need "uart_handle_cts_change" to invoke "start_tx/stop_tx"
for flow control.
In addition, for software CTS, interrupt "SC16IS7XX_IIR_CTSRTS_SRC"
just report the nCTS change of state from active(low) to inactive(high),
driver don't know when the state of nCTS change from incactive to active,
so can't resume the transmission when a peer device is again ready and
re-assert nRTS signal.
Signed-off-by: Wills Wang <wills.wang@live.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some RS-232 to RS-485 transceivers require Rx to be disabled on Tx to
avoid echo of Tx data into the Rx buffer. Specifically, the XR3160E
RS-232/RS-485/RS-422 transceiver behaves this way.
This commit disables Rx on active Tx when SER_RS485_ENABLED is active and
SER_RS485_RX_DURING_TX is disabled.
Note that this is a change in behavior of the driver. Until now
SER_RS485_RX_DURING_TX was enabled unconditionally even when disabled in
the TIOCSRS485 ioctl serial_rs485 flags field.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling support for the UART on Marvell EBU SoCs only make sense when
compiling for Marvell EBU SoCs, unless compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/Kconfig:config SERIAL_MVEBU_UART
drivers/tty/serial/Kconfig: bool "Marvell EBU serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since the code wasn't using module_init to begin with, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to set .owner here. The core will do it.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Wilson Ding <dingwei@marvell.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split off the bulk of the existing meson_serial_console_write()
implementation into meson_serial_port_write() for implementing
meson_serial_early_console_write().
Use "meson" as the earlycon driver name, courtesy of Nicolas.
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The issue with setting up a fixed clock rate at probe is that it would
overwrite the console rate set by the bootloader for its console device.
This would result in serial out corruption or missing log when we system
is booted with earlycon. This is not a issue if we boot system without
earlycon.
This setup is at least not required with the mainline driver, this code
used to be required because the clk_enable() call would fail if
clk_set_rate() wasn't called first.
Originally the issue was noticed on DB410c which is based on APQ8016
chipset.
Without this patch the console log with earlycon would look like:
...
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=1
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
����+HH��0.699378] console [ttyMSM0] enabled
[ 0.699378] console [ttyMSM0] enabled
[ 0.702003] bootconsole [uart0] disabled
[ 0.702003] bootconsole [uart0] disabled
...
with this patch I can see all the skipped lines on the console
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Pramod Gurav <gpramod@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
noctty was removed as a parameter by commit 11e1d4aa4d
("tty: Consolidate noctty check in tty_open()").
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TTY_NUMBER() has been unused since v2.5.71; removed by
"[PATCH] callout removal: callout is gone".
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For tty operations which may expect uart port to have been removed
but still have other necessary work to accomplish, check for NULL
uart port; specifically uart_close(), uart_hangup() and sub-functions
(uart_shutdown() and uart_port_shutdown()).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For serial core operations not already excluded by holding port->mutex,
use reference counting to protect deferencing the state->uart_port.
Introduce helper functions, uart_port_ref() and uart_port_deref(), to
wrap uart_port access, and helper macros, uart_port_lock() and
uart_port_unlock(), to wrap combination uart_port access with uart
port lock sections.
Port removal in uart_remove_one_port() waits for reference count to
drop to zero before detaching the uart port from struct uart_state.
For functions only reading the tx circular buffer indexes (where the
uart port lock is claimed to prevent concurrent users), a NULL uart
port is simply ignored and the operation completes normally.
For functions change the tx circular buffer indexes (where the uart
port lock is claimed to prevent concurrent users), the operation is
aborted if the uart port is NULL (ie., has been detached).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uart_remove_one_port() may race with every serial core operation
requiring a valid dereference of state->uart_port. In particular,
uart_remove_one_port() may unlink the uart port concurrently with
any serial core operation that may dereference same.
Ensure safe dereference for those operations that already claim
the port->mutex, and extend that guarantee for trivial cases,
such as the ioctl handlers. Introduce the uart_port_check() helper
which asserts port->mutex is held (only when lockdep is on).
For ioctls, return -EIO as if the port has been hung up (since it has).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare uart_poll_init() to safely dereference uart port; expand the
port mutex section to guarantee uart port remains valid until
uart_poll_init() completes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ASYNC*_SHARE_IRQ is no longer used; remove.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ASYNC_INITIALIZED bit in the tty_port::flags field with
TTY_PORT_INITIALIZED bit in the tty_port::iflags field. Introduce helpers
tty_port_set_initialized() and tty_port_initialized() to abstract
atomic bit ops.
Note: the transforms for test_and_set_bit() and test_and_clear_bit()
are unnecessary as the state transitions are already mutually exclusive;
the tty lock prevents concurrent open/close/hangup.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ASYNC_SUSPENDED bit in the tty_port::flags field with
TTY_PORT_SUSPENDED bit in the tty_port::iflags field. Introduce helpers
tty_port_set_suspended() and tty_port_suspended() to abstract
atomic bit ops.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ASYNC_CHECK_CD bit in the tty_port::flags field with
TTY_PORT_CHECK_CD bit in the tty_port::iflags field. Introduce helpers
tty_port_set_check_carrier() and tty_port_check_carrier() to abstract
the atomic bit ops.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ASYNC_NORMAL_ACTIVE bit in the tty_port::flags field with
TTY_PORT_ACTIVE bit in the tty_port::iflags field. Introduce helpers
tty_port_set_active() and tty_port_active() to abstract atomic bit ops.
Extract state changes from port lock sections, as this usage is
broken and confused; the state transitions are protected by the
tty lock (which mutually excludes parallel open/close/hangup),
and no user tests the active state while holding the port lock.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace ASYNC_CTS_FLOW bit in the tty_port::flags field with
TTY_PORT_CTS_FLOW bit in the tty_port::iflags field. Add
tty_port_set_cts_flow() helper to abstract the atomic bit ops.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Abstract TTY_THROTTLED bit tests with tty_throttled().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Abstract TTY_IO_ERROR status test treewide with tty_io_error().
NB: tty->flags uses atomic bit ops; replace non-atomic bit test
with test_bit().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Version 2 of the Server Base System Architecture (SBSAv2) describes UART
hardware registers as 32 bits wide, giving no guidance on access sizes. The
SBSA UART driver previously assumed partial-length 16 and 8 bit accesses would
work. But the SBSAv2 UART hardware on the Qualcomm Technologies QDF2432 only
supports full-length 32 bit register accesses, so use those exclusively. This
is compatible with SBSAv3, which explicitly requires UART hardware support 32
(and 16 and sometimes 8) bit accesses.
Tested on Juno, Midway, QDF2432, Seattle, and X-Gene 1.
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1cf6e8fc83 ("tty/serial: at91: fix RTS line management when
hardware handshake is enabled") actually allowed to enable hardware
handshaking.
Before, the CRTSCTS flags was silently ignored.
As the DMA controller can't drive RTS (as explain in the commit message).
Ensure that hardware flow control stays disabled when DMA is used and FIFOs
are not available.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fixes: 1cf6e8fc83 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled")
Cc: stable <stable@vger.kernel.org> # v4.0+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry reported, that the current cleanup code in n_gsm can trigger a
warning:
WARNING: CPU: 2 PID: 24238 at drivers/tty/n_gsm.c:2048 gsm_cleanup_mux+0x166/0x6b0()
...
Call Trace:
...
[<ffffffff81247ab9>] warn_slowpath_null+0x29/0x30 kernel/panic.c:490
[<ffffffff828d0456>] gsm_cleanup_mux+0x166/0x6b0 drivers/tty/n_gsm.c:2048
[<ffffffff828d4d87>] gsmld_open+0x5b7/0x7a0 drivers/tty/n_gsm.c:2386
[<ffffffff828b9078>] tty_ldisc_open.isra.2+0x78/0xd0 drivers/tty/tty_ldisc.c:447
[<ffffffff828b973a>] tty_set_ldisc+0x1ca/0xa70 drivers/tty/tty_ldisc.c:567
[< inline >] tiocsetd drivers/tty/tty_io.c:2650
[<ffffffff828a14ea>] tty_ioctl+0xb2a/0x2140 drivers/tty/tty_io.c:2883
...
But this is a legal path when open fails to find a space in the
gsm_mux array and tries to clean up. So make it a standard test
instead of a warning.
Reported-by: "Dmitry Vyukov" <dvyukov@google.com>
Cc: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/CACT4Y+bHQbAB68VFi7Romcs-Z9ZW3kQRvcq+BvHH1oa5NcAdLA@mail.gmail.com
Fixes: 5a640967 ("tty/n_gsm.c: fix a memory leak in gsmld_open()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 21947ba654 ("serial: 8250_pci: replace switch-case by
formula"), the 8250 driver crashes in the byt_set_termios() function
with a divide error. This is caused by the fact that a baud rate of 0 (B0)
is not handled properly. Fix it by falling back to B9600 in this case.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Fixes: 21947ba654 ("serial: 8250_pci: replace switch-case by formula")
Cc: stable@vger.kernel.org
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is more prep-work for the upcoming pty changes. Still just code
cleanup with no actual semantic changes.
This removes a bunch pointless complexity by just having the slave pty
side remember the dentry associated with the devpts slave rather than
the inode. That allows us to remove all the "look up the dentry" code
for when we want to remove it again.
Together with moving the tty pointer from "inode->i_private" to
"dentry->d_fsdata" and getting rid of pointless inode locking, this
removes about 30 lines of code. Not only is the end result smaller,
it's simpler and easier to understand.
The old code, for example, depended on the d_find_alias() to not just
find the dentry, but also to check that it is still hashed, which in
turn validated the tty pointer in the inode.
That is a _very_ roundabout way to say "invalidate the cached tty
pointer when the dentry is removed".
The new code just does
dentry->d_fsdata = NULL;
in devpts_pty_kill() instead, invalidating the tty pointer rather more
directly and obviously. Don't do something complex and subtle when the
obvious straightforward approach will do.
The rest of the patch (ie apart from code deletion and the above tty
pointer clearing) is just switching the calling convention to pass the
dentry or file pointer around instead of the inode.
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Jann Horn <jann@thejh.net>
Cc: Greg KH <greg@kroah.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Florian Weimer <fw@deneb.enyo.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Here are 3 serial driver fixes for issues that have been reported. Two
are reverts, fixing problems that were in the big TTY/Serial driver
merge in 4.6-rc1, and the last one is a simple bugfix for a regression
that showed up in 4.6-rc1 as well.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlcbSMkACgkQMUfUDdst+ymBkACgqvOCijwdNr0MrvU2/zxdJYNJ
3EEAnjrQUvDVqMPem9fiR9Y7I1iGPYNx
=Ux5a
-----END PGP SIGNATURE-----
Merge tag 'tty-4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial fixes from Greg KH:
"Here are 3 serial driver fixes for issues that have been reported.
Two are reverts, fixing problems that were in the big TTY/Serial
driver merge in 4.6-rc1, and the last one is a simple bugfix for a
regression that showed up in 4.6-rc1 as well.
All have been in linux-next with no reported issues"
* tag 'tty-4.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250: Add hardware dependency to RT288X option"
tty/serial/8250: fix RS485 half-duplex RX
Revert "serial-uartlite: Constify uartlite_be/uartlite_le"
This reverts commit 8d2acdb9fc.
It's causing problems, and somehow I missed that Peter didn't like it at
all :(
So revert it for now until it gets sorted out.
Reported-by: Mason <slash.tmp@free.fr>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Mans Rullgard <mans@mansr.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
When in half-duplex mode RX will be disabled before TX, but not
enabled after deactivating transmitter. This patch enables
UART_IER_RLSI and UART_IER_RDI interrupts after TX is over.
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Fixes: e490c9144c ("tty: Add software emulated RS485 support for 8250")
Acked-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This gets rid of the horrible notion of having that
struct inode *ptmx_inode
be the linchpin of the interface between the pty code and devpts.
By de-emphasizing the ptmx inode, a lot of things actually get cleaner,
and we will have a much saner way forward. In particular, this will
allow us to associate with any particular devpts instance at open-time,
and not be artificially tied to one particular ptmx inode.
The patch itself is actually fairly straightforward, and apart from some
locking and return path cleanups it's pretty mechanical:
- the interfaces that devpts exposes all take "struct pts_fs_info *"
instead of "struct inode *ptmx_inode" now.
NOTE! The "struct pts_fs_info" thing is a completely opaque structure
as far as the pty driver is concerned: it's still declared entirely
internally to devpts. So the pty code can't actually access it in any
way, just pass it as a "cookie" to the devpts code.
- the "look up the pts fs info" is now a single clear operation, that
also does the reference count increment on the pts superblock.
So "devpts_add/del_ref()" is gone, and replaced by a "lookup and get
ref" operation (devpts_get_ref(inode)), along with a "put ref" op
(devpts_put_ref()).
- the pty master "tty->driver_data" field now contains the pts_fs_info,
not the ptmx inode.
- because we don't care about the ptmx inode any more as some kind of
base index, the ref counting can now drop the inode games - it just
gets the ref on the superblock.
- the pts_fs_info now has a back-pointer to the super_block. That's so
that we can easily look up the information we actually need. Although
quite often, the pts fs info was actually all we wanted, and not having
to look it up based on some magical inode makes things more
straightforward.
In particular, now that "devpts_get_ref(inode)" operation should really
be the *only* place we need to look up what devpts instance we're
associated with, and we do it exactly once, at ptmx_open() time.
The other side of this is that one ptmx node could now be associated
with multiple different devpts instances - you could have a single
/dev/ptmx node, and then have multiple mount namespaces with their own
instances of devpts mounted on /dev/pts/. And that's all perfectly sane
in a model where we just look up the pts instance at open time.
This will eventually allow us to get rid of our odd single-vs-multiple
pts instance model, but this patch in itself changes no semantics, only
an internal binding model.
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Serge Hallyn <serge.hallyn@ubuntu.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Jann Horn <jann@thejh.net>
Cc: Greg KH <greg@kroah.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Florian Weimer <fw@deneb.enyo.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The source and destination masters are reflecting buses or their layers to
where the different devices can be connected. The patch changes the master
names to reflect which one is related to which independently on the transfer
direction.
The outcome of the change is that the memory data width is now always limited
by a data width of the master which is dedicated to communicate to memory.
The patch will not break anything since all current users have the same data
width for all masters. Though it would be nice to revisit avr32 platforms to
check what is the actual hardware topology in use there. It seems that it has
one bus and two masters on it as stated by Table 8-2, that's why everything
works independently on the master in use. The purpose of the sequential patch
is to fix the driver for configuration of more than one bus.
The change is done in the assumption that src_master and dst_master are
reflecting a connection to the memory and peripheral correspondently on avr32
and otherwise on the rest.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit e9036d0662 ("tty: Drop krefs for interrupted tty lock")
fixed a tty reference counting problem introduced in
commit 0bfd464d3f ("tty: Wait interruptibly for tty lock on reopen"),
so v4.5.0 is correct.
However, commit d6203d0c7b ("tty: Refactor tty_open()") moved the
relevant code for 4.6-rc1; correct the merge.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
User-Mode Linux supplies an alternate TTY_MAJOR driver for stdio console,
so the noctty check in tty_open() must apply only to VT driver tty0
devnode and not the UML console driver tty0 devnode.
Fixes: 11e1d4aa4d ("tty: Consolidate noctty checks in tty_open()")
Reported-by: Richard Weinberger <richard.weinberger@gmail.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Make earlyprintk=xen work for HVM guests.
- Remove module support for things never built as modules.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW8YhlAAoJEFxbo/MsZsTRiCgH/3GnL93s/BsRTrA/DYykYqA4
rPPkDd6WMlEbrko6FY7o4IxUAZ50LWU8wjmDNVTT+R/VKlWCVh2+ksxjbH8e0nzr
0QohAYTdG1VGmhkrwTjKj0wC3Nr8vaDqoBXAFRz4DiQdbobn12wzXjaVrbl8RRNc
oHDqR+DfZj6ontqx8oFkkTk7CFKIGEOtm/uBhCAV2fNkQSUCzuQyKLlarxM6jq/2
EnLR1bhnyoy5zNFzXxmaJgZOit8QFMKvPdDRknlp9yDHYJ5zolJkv+6FPiAG6SZs
A8yAUPQoAD+ekAiV2DIhb8qoNNNdZXdRCFBpoudwX3GyyU4O2P5Intl0xEg17Nk=
=L8S4
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
"Features and fixes for 4.6:
- Make earlyprintk=xen work for HVM guests
- Remove module support for things never built as modules"
* tag 'for-linus-4.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
drivers/xen: make platform-pci.c explicitly non-modular
drivers/xen: make sys-hypervisor.c explicitly non-modular
drivers/xen: make xenbus_dev_[front/back]end explicitly non-modular
drivers/xen: make [xen-]ballon explicitly non-modular
xen: audit usages of module.h ; remove unnecessary instances
xen/x86: Drop mode-selecting ifdefs in startup_xen()
xen/x86: Zero out .bss for PV guests
hvc_xen: make early_printk work with HVM guests
hvc_xen: fix xenboot for DomUs
hvc_xen: add earlycon support
CONFIG_SERIAL_8250_RSA has waited for a long
time to have meaningful help text so let's
finally describe what this option actually does.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch optimizes UART rx fifo access routine by reading UART SFR
when necessary. At first, the "fifocnt" variable will be initialized
as Rx FIFO count. So we don't need to access UFSTAT(FIFO status) register
every time to check FIFO count because we know that count with "fifocnt".
After all data were read out from Rx FIFO, the "fifocnt" will be set as 0.
Lastly, UFSTAT will be accessed again to check whether the data remains
by any chance.
Signed-off-by: Youngmin Nam <ym0914@gmail.com>
Reviewed-by: Jung-Ick Guack <ji.guack@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PL011 UART has hardware mark/space parity ability, this trivial patch adds support for it.
Tested on Raspberry Pi v1, v2 (BCM2835 and BCM2836)
Signed-off-by: Ed Spiridonov <edo.rus@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
up_to_u8250p() casts struct uart_port * to struct uart_8250_port *. Update code
to use it instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Mediatek 8250 driver has a 'bool' Kconfig symbol, but that
breaks when SERIAL_8250 is a loadable module:
drivers/tty/built-in.o: In function `mtk8250_set_termios':
:(.text+0x1bee8): undefined reference to `serial8250_do_set_termios'
:(.text+0x1bf10): undefined reference to `uart_get_baud_rate'
:(.text+0x1c09c): undefined reference to `uart_get_divisor'
drivers/tty/built-in.o: In function `mtk8250_do_pm':
:(.text+0x1c0d0): undefined reference to `serial8250_do_pm'
drivers/tty/built-in.o: In function `mtk8250_probe':
:(.text+0x1c2e4): undefined reference to `serial8250_register_8250_port'
serial/8250/8250_mtk.c:287:242: error: data definition has no type or storage class [-Werror]
serial/8250/8250_mtk.c:287:122: error: 'mtk8250_platform_driver_init' defined but not used [-Werror=unused-function]
This changes the symbol to a 'tristate', so the dependency on
SERIAL_8250 also works when that is set to 'm'.
To actually build the driver, we also need to include <linux/module.h>.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Ingenic 8250 driver has a 'bool' Kconfig symbol, but that
breaks when SERIAL_8250 is a loadable module:
drivers/tty/built-in.o: In function `ingenic_uart_probe':
8250_ingenic.c:(.text+0x1c1a0): undefined reference to `serial8250_register_8250_port'
This changes the symbol to a 'tristate', plus a dependency on
SERIAL_8250, which makes it work again. Unlike the other
soc-specific backends, this one has no dependency on an
architecture or a platform. I'm adding a dependency on
MIPS || COMPILE_TEST as well here, to avoid showing the driver
on architectures that are not interested in it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly added uniphier serial port driver fails to build as
a loadable module when the base 8250 driver is built-in and
its console support enabled:
ERROR: "early_serial8250_setup" [drivers/tty/serial/8250/8250_uniphier.ko] undefined!
This changes the driver to only provide the early console support
if it is built-in itself as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cafe1ac640 ("drivers/tty: make serial
8250_ingenic.c explicitly non-modular"), which attempted to remove dead
code but did not have the desired effect when the main 8250 driver was
a loadable module itself.
This would normally result in a link error, but as the entire
drivers/tty/serial/8250/ directory is only entered when CONFIG_SERIAL_8250
is set, we never notice that the driver does not get built in this
configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d72d391c12 ("drivers/tty/serial: make
8250/8250_mtk.c explicitly non-modular"), which intended to remove dead
code but did not have the desired effect when the main 8250 driver was
a module itself.
This would normally result in a link error, but as the entire
drivers/tty/serial/8250/ directory is only entered when CONFIG_SERIAL_8250
is set, we never notice that the driver does not get built in this
configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Armada-3700's uart is a simple serial port, which doesn't
support. Configuring the modem control lines. The uart port has a 32
bytes Tx FIFO and a 64 bytes Rx FIFO
The uart driver implements the uart core operations. It also support the
system (early) console based on Armada-3700's serial port.
Known Issue:
The uart driver currently doesn't support clock programming, which means
the baud-rate stays with the default value configured by the bootloader
at boot time
[gregory.clement@free-electrons.com: Rewrite many part which are too long
to enumerate]
Signed-off-by: Wilson Ding <dingwei@marvell.com>
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the mctrl_gpio driver can be built as a module, it needs to have its
license specified with MODULE_LICENSE. Otherwise, it cannot access
required symbols exported through EXPORT_SYMBOL_GPL.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc warns about a potential use of an uninitialized variable in this driver:
drivers/tty/serial/ifx6x60.c: In function 'ifx_spi_complete':
drivers/tty/serial/ifx6x60.c:713:6: warning: 'more' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (more || ifx_dev->spi_more || queue_length > 0 ||
Unlike a lot of other such warnings, this one is correct and describes
an actual problem in the handling of the "IFX_SPI_HEADER_F" result code.
This appears to be a result from a restructuring of the driver that
dates back to before it was merged in the kernel, so it's impossible
to know where it went wrong. I also don't know what that result code
means, so I have no idea if setting 'more' to zero is the correct
solution, but at least it makes the behavior reproducible rather than
depending on whatever happens to be on the kernel stack.
This patch initializes the 'more' variable to zero in each of the
three code paths that could result in undefined behavior before,
which is more explicit than initializing it at the start of the
function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With SAMA5D2, the UART has hw timeout but the offset of the register to
define this value is not the same as the one for USART.
When using the new UART, the value of this register was 0 so we never
get timeout irqs. It involves that when using DMA, we were stuck until
the execution of the dma callback which happens when a buffer is full
(so after receiving 2048 bytes).
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit c39dfebc77, the modular support
code for atmel_serial was removed, as the driver cannot be built as a
module. Because no use case was proposed, the dynamic driver binding
support was removed as well.
The atmel_serial driver can manage up to 7 serial controllers, which are
multiplexed with other functions. For example, in the Atmel SAMA5D2, the
Flexcom controllers can work as USART, SPI or I2C controllers, and on
all Atmel devices serial lines can be reconfigured as GPIOs.
My use case uses GPIOs to transfer a firmware update using a custom
protocol on the lines used as a serial port during the normal life of
the device. If it is not possible to unbind the atmel_serial driver, the
GPIO lines remain reserved and prevent this case from working.
This patch reinstates the atmel_serial_remove function, and fixes it as
it failed to clear the "clk" field on removal, triggering an oops when
a device was bound again after being unbound.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kconfig option SERIAL_8250_RT288X seems to be only relevant on MIPS
platforms, so do not present it on other architectures, unless
build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Mans Rullgard <mans@mansr.com>
Cc: Jiri Slaby <jslaby@suse.com>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the platform bus sets the platform_device id to -1 (PLATFORM_DEVID_NONE),
use an incrementing counter for the TTY index instead
Signed-off-by: Greg Hackmann <ghackmann@google.com>
Signed-off-by: Jin Qian <jinqian@android.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable support for registering this device using the device tree.
Device tree node example for registering Goldfish TTY device :
goldfish_tty@1f004000 {
interrupts = <0xc>;
reg = <0x1f004000 0x1000>;
compatible = "google,goldfish-tty";
};
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Jin Qian <jinqian@android.com>
Signed-off-by: Alan <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device generates a short rising pulse on the interrupt request line.
Signed-off-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Better to hold the spinlock as short as possible.
Signed-off-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device is ideal to use when you need a lot of uarts in your FPGA.
Try not to force all those users to patch their kernel.
Signed-off-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to have channel offset defined since all BayTrail and Braswell
ports are 1 channel. Remove unneeded definition.
While here, remove comment which has no value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The managed API provides a better approach to help with acquiring and releasing
resources. Besides that error handling becomes simpler.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clocks are managed through clk-fractional-divider.c module, and thus CLK
framework takes care about it. Remove letfovers from this driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the main branch contains return statement the 'else' keyword is not
needed. Remove it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support early console setup via DT for all listed compatible strings.
Remove EARLYCON_DECLARE which was done by:
"Use common framework for earlycon declarations"
(sha1: 2eaa790989)
when OF_EARLYCON_DECLARE is defined.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of commit 2eaa790989 ("earlycon: Use common framework for
earlycon declarations") it is no longer needer to specify both
EARLYCON_DECLARE() and OF_EARLYCON_DECLARE().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When only a TX DMA channel is specified in DT, pl011_dma_probe() falls
back to looking for the optional RX channel in platform data. What it
doesn't do is check whether that platform data actually exists...
Add the missing check to avoid crashing the kernel.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
serial8250_em485_init() is supposed to be protected with
p->port.lock spinlock.
This may lead to issues when kmalloc sleeps, so it is better to use
GFP_ATOMIC in this spinlocked context.
Fixes: e490c9144c ("tty: Add software emulated RS485 support for 8250")
Reported-by: Ильяс Гасанов <torso.nafi@gmail.com>
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Formally, currently there is no memory leak, but if
serial8250_ports[line] is reused with other 8250 driver, then em485
will be already activated and it will cause issues.
Fixes: e490c9144c ("tty: Add software emulated RS485 support for 8250")
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While building with W=1 we were getting build warning:
drivers/tty/tty_audit.c:149:16: warning: variable 'sessionid' set but not used
The local variable sessionid was only assigned the value of
current->sessionid but was never reused. On further inspection it turned
out that there is no need of audit_get_loginuid() also.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a3f0b77f36.
Maarten writes:
It appears to be wrong and I don't have a good idea how to fix
it yet.
Cc: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
Refactor the existing code in xen_raw_console_write to get the generic
early_printk console work with HVM guests.
Take the opportunity to replace the outb loop with a single outsb call
to reduce the number of vmexit.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
The xenboot early console has been partially broken for DomU for a long
time: the output would only go to the hypervisor via hypercall
(HYPERVISOR_console_io), while it wouldn't actually go to the DomU
console. The reason is that domU_write_console would return early as no
xencons structs are configured for it.
Add an appropriate xencons struct for xenboot from the xenboot setup
callback.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Introduce EARLYCON support in hvc_xen, useful for early debugging on arm
and arm64, where xen early_printk is not available.
It is different from xenboot_write_console on x86 in two ways:
- it does not return if !xen_pv_domain(), not only because ARM guests
are xen_hvm_domain(), but also because we want to capture all the
early boot messages, before xen support is discovered
- it does not try to print to the domU console at all, because xen
support will only be discovered at a later point
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Add support for manual getting the modem control lines.
Signed-off-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for manual setting the modem control lines.
Signed-off-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IS_ERR_VALUE() assumes that its parameter is an unsigned long.
It can not be used to check if an unsigned int reflects an error.
Doing so can result in the following build warning.
drivers/tty/serial/digicolor-usart.c: In function ‘digicolor_uart_probe’:
include/linux/err.h:21:38: warning:
comparison is always false due to limited range of data type
drivers/tty/serial/digicolor-usart.c:485:6: note:
in expansion of macro ‘IS_ERR_VALUE’
If that warning is seen, an error return from platform_get_irq() is missed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IS_ERR_VALUE() assumes that its parameter is an unsigned long.
It can not be used to check if an unsigned int reflects an error.
Doing so can result in the following build warning.
drivers/tty/serial/clps711x.c: In function ‘uart_clps711x_probe’:
include/linux/err.h:21:38: warning:
comparison is always false due to limited range of data type
drivers/tty/serial/clps711x.c:471:6: note: in expansion of macro ‘IS_ERR_VALUE’
If that warning is seen, an error return from platform_get_irq() is missed.
Use a temporary variable to check for errors from platform_get_irq().
Also don't use IS_ERR_VALUE() to check if an integer variable is < 0.
The variable can be checked directly in that case.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes error condition check when requesting the irq,
that would not trigger because of uart_port.irq being
defined as unsigned int.
Reported by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declare an OF early console for Tegra so that the early console device
can be specified via the "stdout-path" property in device-tree.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mtk8250_runtime_suspend function is not used when runtime PM is
disabled, so we get a warning about an unused function:
drivers/tty/serial/8250/8250_mtk.c:119:12: error: 'mtk8250_runtime_suspend' defined but not used [-Werror=unused-function]
static int mtk8250_runtime_suspend(struct device *dev)
This marks all the PM functions as __maybe_unused to avoid the warning,
and removes the #ifdef around the PM_SLEEP functions for consistency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the baudrate calculation for 24 MHz XTAL clock found on gxbb platforms.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These hv_ops structures are never modified, so declare them as const. Most
were const already.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d56edd7ed0, it
shouldn't have been applied, it was fixed properly with commit
71f50c6d9a ("of: drop symbols declared by
_OF_DECLARE() from modules")
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable "len" gets assigned once and it's value copied to
"n", which is then used for the rest of the function.
This patch fixes the unnecessary variable reassignment by using "len"
throughout the function instead.
Signed-off-by: Jakob Østergaard Jensen <jakob.jensen.91@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Considering current pty code and multiple devpts instances, it's possible
to umount a devpts file system while a program still has /dev/tty opened
pointing to a previosuly closed pty pair in that instance. In the case all
ptmx and pts/N files are closed, umount can be done. If the program closes
/dev/tty after umount is done, devpts_kill_index will use now an invalid
super_block, which was already destroyed in the umount operation after
running ->kill_sb. This is another "use after free" type of issue, but now
related to the allocated super_block instance.
To avoid the problem (warning at ida_remove and potential crashes) for
this specific case, I added two functions in devpts which grabs additional
references to the super_block, which pty code now uses so it makes sure
the super block structure is still valid until pty shutdown is done.
I also moved the additional inode references to the same functions, which
also covered similar case with inode being freed before /dev/tty final
close/shutdown.
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Cc: stable@vger.kernel.org # 2.6.29+
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change fixes a bug for a corner case where we have the the last
release from a pty master/slave coming from a previously opened /dev/tty
file. When this happens, the tty->driver_data can be stale, due to all
ptmx or pts/N files having already been closed before (and thus the inode
related to these files, which tty->driver_data points to, being already
freed/destroyed).
The fix here is to keep a reference on the opened master ptmx inode.
We maintain the inode referenced until the final pty_unix98_shutdown,
and only pass this inode to devpts_kill_index.
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Cc: <stable@vger.kernel.org> # 2.6.29+
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add_softcursor() stores the contents of the text buffer position in this
variable before drawing the softcursor, whereas hide_softcursor() writes
the value back. A value of -1 means that no cursor has been drawn and
therefore no character is to be restored. softcursor_original, however,
is only implicitly initialized with 0. Therefore, when hide_softcursor
is called for the first time (console_init -> con_init -> redraw_screen
-> hide_cursor), it wrongly writes 0x0000 in the top left corner of
the text buffer. Normally, this is just as black as the rest of the
screen (vc_video_erase_char) and can't be seen, but it appears as a
black cursor rectangle on non-black backgrounds e.g. with boot option
"vt.global_cursor_default=0 vt.color=0xf0". softcursor_original needs
to be initialized with -1.
Signed-off-by: Melchior FRANZ <mfranz@aon.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xencons_disconnect_backend() is only called from xen_console_remove(),
which is conditionally compiled, so we get a harmless warning when
CONFIG_HVC_XEN_FRONTEND is unset:
hvc/hvc_xen.c:350:12: error: 'xen_console_remove' defined but not used [-Werror=unused-function]
This moves the function down into the same #ifdef section to silence
the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_PCI is not set, enabling CONFIG_CYZ_INTR has no
practical effect other than generating a warning about an
unused function:
drivers/tty/cyclades.c:1184:20: warning: 'cyz_interrupt' defined but not used [-Wunused-function]
static irqreturn_t cyz_interrupt(int irq, void *dev_id)
This adds a dependency to avoid that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The nozomi wireless data driver has its own helper function to
transfer data from a FIFO, doing an extra byte swap on big-endian
architectures, presumably to bring the data back into byte-serial
order after readw() or readl() perform their implicit byteswap.
This helper function is used in the receive_data() function to
first read the length into a 32-bit variable, which causes
a compile-time warning:
drivers/tty/nozomi.c: In function 'receive_data':
drivers/tty/nozomi.c:857:9: warning: 'size' may be used uninitialized in this function [-Wmaybe-uninitialized]
The problem is that gcc is unsure whether the data was actually
read or not. We know that it is at this point, so we can replace
it with a single readl() to shut up that warning.
I am leaving the byteswap in there, to preserve the existing
behavior, even though this seems fishy: Reading the length of
the data into a cpu-endian variable should normally not use
a second byteswap on big-endian systems, unless the hardware
is aware of the CPU endianess.
There appears to be a lot more confusion about endianess in this
driver, so it probably has not worked on big-endian systems in
a long time, if ever, and I have no way to test it. It's well
possible that this driver has not been used by anyone in a while,
the last patch that looks like it was tested on the hardware is
from 2008.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Constifies tty_port_operations structures in
the tty driver since they are not modified
after their initialization.
Detected and found using Coccinelle.
Suggested-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The class of 4 n_hdls buf locks is the same because a single function
n_hdlc_buf_list_init is used to init all the locks. But since
flush_tx_queue takes n_hdlc->tx_buf_list.spinlock and then calls
n_hdlc_buf_put which takes n_hdlc->tx_free_buf_list.spinlock, lockdep
emits a warning:
=============================================
[ INFO: possible recursive locking detected ]
4.3.0-25.g91e30a7-default #1 Not tainted
---------------------------------------------
a.out/1248 is trying to acquire lock:
(&(&list->spinlock)->rlock){......}, at: [<ffffffffa01fd020>] n_hdlc_buf_put+0x20/0x60 [n_hdlc]
but task is already holding lock:
(&(&list->spinlock)->rlock){......}, at: [<ffffffffa01fdc07>] n_hdlc_tty_ioctl+0x127/0x1d0 [n_hdlc]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&list->spinlock)->rlock);
lock(&(&list->spinlock)->rlock);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by a.out/1248:
#0: (&tty->ldisc_sem){++++++}, at: [<ffffffff814c9eb0>] tty_ldisc_ref_wait+0x20/0x50
#1: (&(&list->spinlock)->rlock){......}, at: [<ffffffffa01fdc07>] n_hdlc_tty_ioctl+0x127/0x1d0 [n_hdlc]
...
Call Trace:
...
[<ffffffff81738fd0>] _raw_spin_lock_irqsave+0x50/0x70
[<ffffffffa01fd020>] n_hdlc_buf_put+0x20/0x60 [n_hdlc]
[<ffffffffa01fdc24>] n_hdlc_tty_ioctl+0x144/0x1d0 [n_hdlc]
[<ffffffff814c25c1>] tty_ioctl+0x3f1/0xe40
...
Fix it by initializing the spin_locks separately. This removes also
reduntand memset of a freshly kzallocated space.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
synclinkmp_init_one() ignores all errors and does not release
all resources if something fails.
The patch adds returned code to device_init() and add_device()
and proper error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use memdup_user rather than duplicating implementation.
found by coccinelle
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/Kconfig:config PPC_EPAPR_HV_BYTECHAN
drivers/tty/Kconfig: bool "ePAPR hypervisor byte channel driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/hvc/Kconfig:config HVC_CONSOLE
drivers/tty/hvc/Kconfig: bool "pSeries Hypervisor Virtual Console support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
We don't replace module.h with init.h since the file already has that.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Anton Blanchard <anton@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes redundant 8250 port initialization macros and
replaces them by a single generic base-macro, which is specialized
as needed.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checkpatch complains about incorrect indentation of switch/case statements.
This patch fixes the corresponding warnings. Additionally some indentation
is changed to match the correct format specified in the Linux Kernel
Coding Style.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch refactors a switch case statement by merging an if condition
in the default case into an identical condition right after the switch
statement.
This comes with a slight change in behaviour: If pci_netmos_9900_numports
returns 0, an additional warning is printed.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes compiler warnings about wrong conversion specifiers used
in a debug output in 8250_pnp.c. The precise warning is:
drivers/tty/serial/8250/8250_pnp.c: In function ‘serial_pnp_probe’:
include/linux/dynamic_debug.h:64:16: warning: format ‘%x’ expects argument
of [...]
drivers/tty/serial/8250/8250_pnp.c:467:2: note: in expansion of macro
‘dev_dbg’
dev_dbg(&dev->dev,
^
include/linux/dynamic_debug.h:64:16: warning: format ‘%lx’ expects argument
of [...]
drivers/tty/serial/8250/8250_pnp.c:467:2: note: in expansion of macro
‘dev_dbg’
dev_dbg(&dev->dev,
^
Those warnings never got triggered, because the command was nested
in an #ifdef, which is removed by a patch of this series.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the macro SERIAL_DEBUG_PNP, which is used to enable
debugging at compile time.
As SERIAL_DEBUG_PNP is an orphan, the corresponding #ifdef is removed.
To keep the ability to enable debugging at compile time,
the call to printk(KERN_DEBUG ...) is replaced by a corresponding
call to dev_dbg(), which is configurable via CONFIG_DYNAMIC_DEBUG.
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces printk by the corresponding variant of dev_* in order
to fix checkpatch warnings. If no suitable device pointer is present, the
corresponding pr_* variant is used.
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merged user-visible multi-line strings into a single line according to the
Linux Kernel Coding Style, which allows user-visible strings to exceed the
maximum line length of 80 characters. The main reason for this is to
facilitate grepping for these strings.
However, some strings were ignored in this patch, because the use of
format specifiers breaks the ability to grep anyway.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a checkpatch warning caused by missing parentheses
in the definition of a macro.
Furthermore redundant parentheses are removed in an assignment.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed checkpatch warning about an unnecessary line continuation in a
multi-line variable assignment.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch moves EXPORT_SYMBOL macros directly after the definition of
the corresponding symbol to remove checkpatch warnings.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checkpatch outputs some warnings about incorrect comment style,
which is fixed by this patch.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a checkpatch warning by moving an opening curly brace
to its correct position.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Indentation is changed to match the correct format of using tabs instead
of spaces wherever possible.
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes whitespace errors reported by checkpatch to increase
readability. Main focus is on missing spaces after commas in
function headers and macros (like foo,bar edited to foo, bar).
Signed-off-by: Anton Würfel <anton.wuerfel@fau.de>
Signed-off-by: Phillip Raffeck <phillip.raffeck@fau.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Transmit interrupts are disabled and the transmit buffer drained in the
course of console output so that polled transmission is possible. That
however causes a lost transmit interrupt as the TxIP bit in RR3 is only
set on a transmit buffer full-to-empty transition and then iff transmit
interrupts are enabled at the same time. Consequently if console output
disturbs a regular transmission in progress, the TxIP bit is never set
again and the transmission locks up waiting for a transmit interrupt.
Fix the problem by restarting transmission manually rather than waiting
for a transmit interrupt that will never happen.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bcm2835 SOC contains an auxiliary uart, which is very close
to the ns16550 with some differences.
The big difference is that the uart HW is not using an internal divider
of 16 but 8, which results in an effictive baud-rate being twice
the requested baud-rate.
This driver handles this device correctly and handles the difference in
the HW divider by scaling up the clock by a factor of 2.
The approach to write a separate (wrapper) driver instead of using a
multiplying clock and "ns16550" as compatibility in the device-tree
has been recommended by Stephen Warren.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend/resume functions should work for 8250_of driver.
Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DRIVER_NAME is too generic to be used in a driver-specific platform
data file. Use a name specific to the driver instead, to avoid
collisions.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WCH382 2S board is a PCIe card with 2 DB9 COM ports detected as
Serial controller: Device 1c00:3253 (rev 10) (prog-if 05 [16850])
Signed-off-by: Jeremy McNicoll <jmcnicol@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wait_for_xmitr() function is only used if CONFIG_CONSOLE_POLL
or CONFIG_SERIAL_OMAP_CONSOLE are set, but when both are disabled,
the compiler warns about it being unused:
drivers/tty/serial/omap-serial.c:1168:13: warning: 'wait_for_xmitr' defined but not used [-Wunused-func
We could add more #ifdefs to work around it, but adding __maybe_unused
seems nicer.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 2172076d23 ("serial/omap-serial: Deinline wait_for_xmitr, save 165 bytes")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The omap-serial driver emulates RS485 delays using software timers,
but neglects to clamp the input values from the unprivileged
ioctl(TIOCSRS485). Because the software implementation busy-waits,
malicious userspace could stall the cpu for ~49 days.
Clamp the input values to < 100ms.
Fixes: 4a0ac0f55b ("OMAP: add RS485 support")
Cc: <stable@vger.kernel.org> # 3.12+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recently added uniphier 8250 port driver supports early console
probing, and it supports being built as a module, but the combination
of the two fails to link:
ERROR: "early_serial8250_setup" [drivers/tty/serial/8250/8250_uniphier.ko] undefined!
Given that earlycon support in a loadable module makes no sense,
making that code conditional on 'MODULE' is a correct solution.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b8d20e06ea ("serial: 8250_uniphier: add earlycon support")
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uartlite driver suffers from missing/duplicate/corrupted character
data when the interrupt handler runs concurrently with access to the
device from another cpu. Take the port spinlock to exclude concurrent
access.
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Microblaze currently uses the old earlyprintk system, rather than the
unified earlycon support, to show boot messages on uartlite. Add
earlycon support so that other archs using uartlite can benefit from
it. The new code in uartlite.c is copied almost verbatim from
arch/microblaze/kernel/early_printk.c.
Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/8250/Kconfig:config SERIAL_8250_INGENIC
drivers/tty/serial/8250/Kconfig: bool "Support for Ingenic SoC serial ports"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, when tring to set up a serial console with a higher
baud rate, it would fallback to 921600.
Tested-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for sparse variable sampling rates on SCIFA and SCIFB.
According to the datasheet, sampling rate 1/5 needs a small quirk to
avoid corrupting the first byte received.
This increases the range and accuracy of supported baud rates.
E.g. on r8a7791/koelsch:
- Supports now 134, 150, and standard 500000-4000000 bps,
- Perfect match for 134, 150, 500000, 1000000, 2000000, and 4000000
bps,
- Accuracy has increased for most standard bps values.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the single sampling rate and special handling for HSCIF's
variable sampling rates by a bitmask and a custom iterator.
This prepares for the advent of SCIFA/SCIFB's sparse variable sampling
rates.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On SCIx variants different from HSCIF, the bit rate is equal to the
sampling clock rate divided by half the sampling rate. Currently this is
handled by dividing the sampling rate by two, which was OK as it was
always even.
Replace halving the sampling rate by premultiplying the base clock
frequency by 2, to accommodate odd sampling rates on SCIFA/SCIFB later.
Replace the shift value in the BRG divider calculation by a
premultiplication of the base clock frequency too, for consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA and SCIFB have additional bit rate config bits in the Serial Mode
Register. Don't touch them when using the port as a serial console, as
we rely on the boot loader to have configured the serial port config.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a non console i.MX UART is enabled in the device tree,
system suspend fails due to an unprepared clock:
[ 638.794563] PM: Syncing filesystems ... done.
[ 638.878902] Freezing user space processes ... (elapsed 0.002 seconds) done.
[ 638.888454] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 638.996697] PM: suspend of devices complete after 97.200 msecs
[ 639.002611] PM: suspend devices took 0.100 seconds
[ 639.013020] PM: late suspend of devices complete after 2.288 msecs
[ 639.021486] ------------[ cut here ]------------
[ 639.026147] WARNING: CPU: 0 PID: 488 at drivers/clk/clk.c:732 clk_core_enable+0xc0/0x12c()
[ 639.034413] Modules linked in:
[ 639.037490] CPU: 0 PID: 488 Comm: system_server Tainted: G W 4.4.0-rc5-pknbsp-svn2214-atag-v4.4-rc5-121-gebfd9cb #1304
[ 639.049312] Hardware name: Freescale i.MX53 (Device Tree Support)
[ 639.055444] [<c0016d54>] (unwind_backtrace) from [<c00140f8>] (show_stack+0x20/0x24)
[ 639.063199] [<c00140f8>] (show_stack) from [<c02c99a0>] (dump_stack+0x20/0x28)
[ 639.070442] [<c02c99a0>] (dump_stack) from [<c0024ca8>] (warn_slowpath_common+0x88/0xc0)
[ 639.078541] [<c0024ca8>] (warn_slowpath_common) from [<c0024d0c>] (warn_slowpath_null+0x2c/0x34)
[ 639.087332] [<c0024d0c>] (warn_slowpath_null) from [<c05171e8>] (clk_core_enable+0xc0/0x12c)
[ 639.095777] [<c05171e8>] (clk_core_enable) from [<c05172f8>] (clk_enable+0x2c/0x40)
[ 639.103441] [<c05172f8>] (clk_enable) from [<c0349880>] (imx_serial_port_suspend_noirq+0x20/0xe0)
[ 639.112336] [<c0349880>] (imx_serial_port_suspend_noirq) from [<c03a26a0>] (dpm_run_callback+0x68/0x16c)
[ 639.121825] [<c03a26a0>] (dpm_run_callback) from [<c03a2898>] (__device_suspend_noirq+0xf4/0x22c)
[ 639.130705] [<c03a2898>] (__device_suspend_noirq) from [<c03a4b0c>] (dpm_suspend_noirq+0x148/0x30c)
[ 639.139764] [<c03a4b0c>] (dpm_suspend_noirq) from [<c00511d4>] (suspend_devices_and_enter+0x2e8/0x6a4)
[ 639.149078] [<c00511d4>] (suspend_devices_and_enter) from [<c00518a0>] (pm_suspend+0x310/0x4b8)
[ 639.157782] [<c00518a0>] (pm_suspend) from [<c00500ec>] (state_store+0x7c/0xcc)
[ 639.165099] [<c00500ec>] (state_store) from [<c02cb6dc>] (kobj_attr_store+0x1c/0x28)
[ 639.172858] [<c02cb6dc>] (kobj_attr_store) from [<c01633d4>] (sysfs_kf_write+0x54/0x58)
[ 639.180871] [<c01633d4>] (sysfs_kf_write) from [<c01629b4>] (kernfs_fop_write+0x100/0x1c8)
[ 639.189152] [<c01629b4>] (kernfs_fop_write) from [<c00fb8b8>] (__vfs_write+0x3c/0xe8)
[ 639.196991] [<c00fb8b8>] (__vfs_write) from [<c00fc810>] (vfs_write+0xa4/0x160)
[ 639.204307] [<c00fc810>] (vfs_write) from [<c00fcac4>] (SyS_write+0x4c/0x98)
[ 639.211363] [<c00fcac4>] (SyS_write) from [<c0010760>] (ret_fast_syscall+0x0/0x3c)
This does not happen for the common case of a single UART used as a console
(since imx_console_setup() already does a prepare)
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
start_tx and the ISR used largely identical code to transmit data.
Consolidate that in one place.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the _OFFSET suffix from all register defines which makes code a
little easier to read and avoids a few line breaks.
Suggested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handling magic sysrq included dropping a lock to avoid a deadlock that
happened when cdns_uart_console_write tried to acquire a lock in the
from the sysrq code path. By making the acquisition of the lock in
cdns_uart_console_write depending on port->sysrq, cdns_uart_handle_rx can be
simplified to simply call uart_handle_sysrq.
Suggested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert an if-else into the more common early return on error, reducing
the indent level of the happy path.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The system could deadlock handling RX IRQs when RX-related IRQ
conditions became true while the receiver was disabled. To avoid this,
enable/disable the RX/TX IRQs together with the receiver/transmitter.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Request_irq() should be _after_ h/w programming, otherwise an
interrupt could be triggered and in-progress before the h/w has been
setup.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move RX-related IRQ handling into a helper function.
Fixes a problem where every char received after a parity or frame error
in the current isr will also be tagged as a parity or frame error.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shutting down the UART port can happen while console operations are in
progress. Holding the port lock serializes these operations and avoids
the UART HW to be disabled in the middle of console prints.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RX path in the interrupt handler released a lock unnecessarily.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The startup function is supposed to initialize the UART for receiving.
Hence, don't enable the TX part. Also, protect HW accesses with the port
lock.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When shutting down the UART, clear the interrupt status register. Bits
in the ISR are cleared by writing them as '1'.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restarting the transmitter even if the circ buffer is empty may be
necessary to push out remaining data when the port is restarted after
being stopped.
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of disabling the IRQ, use the spin lock to serialize accesses to
the HW. This protects the driver from interference of non-IRQ callbacks
with each other and makes the driver more consistent in its
serialization method.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"earlyprintk" is architecture specific option.
General "earlycon" option support is much better.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
[uli: preserve other SCSCR bits when asserting RE and TE]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
[geert: rewording, #ifdef rework]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Considering that pci_pericom_setup(()'s only difference to
pci_default_setup() is the setting of the uartclk field, and taking
into account that this field already gets taken care of by having the
base_baud field filled in the pci_boards[] entries, there's no need
for both the function and the quirks table entry.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use to_pci_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pl011 driver has gone back and forth on the definition of the
ZTE specific variation of the hardware definitions, but the
current state is that the vendor definition is left in place
yet unused:
drivers/tty/serial/amba-pl011.c:190:27: warning: 'vendor_zte' defined but not used [-Wunused-variable]
I don't know what the plan forward is to get this code to work,
but the current behavior is a bit annoying as we get a warning
whenever we build this driver.
This patch does not help us to make it work, but at least
shuts up the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 7ec7587189 ("tty: amba-pl011: add support for ZTE UART (EXPERIMENTAL)")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Busy loops that poll on a register should call cpu_relax(). On some
architectures, it can lower CPU power consumption or yield to a
hyperthreaded twin processor. It also serves as a compiler barrier,
so it can replace barrier() calls.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In datasheet, Modem Status Register MSR[4-7] reflect the modem pins
CTS/DSR/RI/CD signal state.
Signed-off-by: Wills Wang <wills.wang@live.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In all functions other than atmel_serial_probe_fifos,
atmel_serial_probe, and atmel_console_init, the name "port" is used to
refer to an instance of struct uart_port. In many of these functions,
"atmel_port" is used to refer to an instance of struct atmel_uart_port.
We make the use of the name "port" consistent by making
atmel_serial_probe_fifos, atmel_serial_probe, and atmel_console_init
use "atmel_port" to refer to an instance of struct atmel_uart_port
instead of the previous name of "port".
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Acked-by: Karthik Manamcheri <karthik.manamcheri@ni.com>
[nicolas.ferre@atmel.com: fix typo in variable, adapt to newer kernel]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with sama5d2, the new UART revision has an hardware timer. So, add it
to the IP detection code and set the "has_hw_timer" property for it.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functional change is associated with this patch.
A driver property depends on the Atmel serial IP revision. This property
is the way the rx timeout is handled: by an hardware or software timer.
So, change this property name and setup code so that it's easier to understand
and more future proof as the distinction of USART vs. UART is blurrier on newer
SoCs.
Variable names and debug comments are also adapted to make this code more obvious.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some UART HW has a single register combining UART_DLL/UART_DLM
(this was probably forgotten in the change that introduced the
callbacks, commit b32b19b8ff)
Fixes: b32b19b8ff ("[SERIAL] 8250: set divisor register correctly ...")
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's old, messy and mostly unmaintained.
Remove it as suggested by Peter Hurley and Alan.
Signed-off-by: Frederik Völkel <frederik.voelkel@fau.de>
Signed-off-by: Lukas Braun <lukas.braun@fau.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Constifies psc_ops structures in tty's serial
port driver since they are not modified after
their initialization.
Detected and found using Coccinelle.
Suggested-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Direct call to readl()/writel() is checked against iotype
and in case of UPIO_MEM32BE we use ioread32be()/iowrite32be()
instead of them.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for UPIO_MEM32BE in addition to UPIO_MEM32.
For big endian we use 2 new accessors similar to little endian,
called dw8250_serial_out32be() and dw8250_serial_in32be().
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the help of Heikki we take common code that
makes sure LCR write wasn't ignored and put it in new function called
dw8250_check_lcr(). This function serves 3 serial_out routines:
dw8250_serial_out(), dw8250_serial_out32(), and dw8250_serial_outq().
This patch only brings better code reuse.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Geert Uytterhoeven
Jiri Slaby
Eric W. Biederman
Arnd Bergmann
Linus Torvalds
Andrei Pistirica
Greg Kroah-Hartman
Florian Westphal
Peter Hurley
Kefeng Wang
Zhao Qiang
Wang Hongcheng
Brian Bloniarz
Yegor Yefremov
Ricardo Ribalda Delgado
Vladimir Murzin
Thierry Reding
Maarten Brock
Masahiro Yamada
Dan Carpenter
Sudip Mukherjee
Andy Shevchenko
Wan Ahmad Zainie
Chanwoo Choi
Stephen Boyd
Uwe Kleine-König
Julia Lawall
Oleksij Rempel
Wills Wang
Baruch Siach
Geert Uytterhoeven
Paul Gortmaker
Andreas Färber
Srinivas Kandagatla
Christopher Covington
Alexandre Belloni
David Müller
Linus Walleij
Maciej S. Szmigiero
Youngmin Nam
Ed Spiridonov
Mathieu OTHACEHE
Wilson Ding
Romain Izard
Ludovic Desroches
Jean Delvare
Greg Hackmann
Miodrag Dinic
Michal Simek
Simon Horman
Robin Murphy
Matwey V. Kornilov
Stefano Stabellini
Guenter Roeck
Martin Sperl
Jon Hunter
Jakob Østergaard Jensen
Herton R. Krzesinski
Melchior FRANZ
Aya Mahfouz
Alexey Khoroshilov
Saurabh Sengar
Anton Wuerfel
Phillip Raffeck
Maciej W. Rozycki
Wang Dongsheng
Jeremy McNicoll
Rich Felker
Jeffy Chen
Martin Fuzzey
Soren Brinkmann
Yoshinori Sato
Jan Beulich
Geliang Tang
Timur Tabi
Jaeden Amero
Nicolas Ferre
Sebastian Frias
Frederik Völkel
Noam Camus