The Layer 2 Update frame is used to update bridges when a station roams
to another AP even if that STA does not transmit any frames after the
reassociation. This behavior was described in IEEE Std 802.11F-2003 as
something that would happen based on MLME-ASSOCIATE.indication, i.e.,
before completing 4-way handshake. However, this IEEE trial-use
recommended practice document was published before RSN (IEEE Std
802.11i-2004) and as such, did not consider RSN use cases. Furthermore,
IEEE Std 802.11F-2003 was withdrawn in 2006 and as such, has not been
maintained amd should not be used anymore.
Sending out the Layer 2 Update frame immediately after association is
fine for open networks (and also when using SAE, FT protocol, or FILS
authentication when the station is actually authenticated by the time
association completes). However, it is not appropriate for cases where
RSN is used with PSK or EAP authentication since the station is actually
fully authenticated only once the 4-way handshake completes after
authentication and attackers might be able to use the unauthenticated
triggering of Layer 2 Update frame transmission to disrupt bridge
behavior.
Fix this by postponing transmission of the Layer 2 Update frame from
station entry addition to the point when the station entry is marked
authorized. Similarly, send out the VLAN binding update only if the STA
entry has already been authorized.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* a fix in the new 6 GHz channel support
* a fix for recent minstrel (rate control) updates
for an infinite loop
* handle interface type changes better wrt. management frame
registrations (for management frames sent to userspace)
* add in-BSS RX time to survey information
* handle HW rfkill properly if !CONFIG_RFKILL
* send deauth on IBSS station expiry, to avoid state mismatches
* handle deferred crypto tailroom updates in mac80211 better
when device restart happens
* fix a spectre-v1 - really a continuation of a previous patch
* advertise NL80211_CMD_UPDATE_FT_IES as supported if so
* add some missing parsing in VHT extended NSS support
* support HE in mac80211_hwsim
* let mac80211 drivers determine the max MTU themselves
along with the usual cleanups etc.
-----BEGIN PGP SIGNATURE-----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=HAuT
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a number of changes, but things are settling down:
* a fix in the new 6 GHz channel support
* a fix for recent minstrel (rate control) updates
for an infinite loop
* handle interface type changes better wrt. management frame
registrations (for management frames sent to userspace)
* add in-BSS RX time to survey information
* handle HW rfkill properly if !CONFIG_RFKILL
* send deauth on IBSS station expiry, to avoid state mismatches
* handle deferred crypto tailroom updates in mac80211 better
when device restart happens
* fix a spectre-v1 - really a continuation of a previous patch
* advertise NL80211_CMD_UPDATE_FT_IES as supported if so
* add some missing parsing in VHT extended NSS support
* support HE in mac80211_hwsim
* let mac80211 drivers determine the max MTU themselves
along with the usual cleanups etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it possibly for drivers to adjust the default max_mtu
by storing it in the hardware struct and using that value
for all interfaces.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/1567738137-31748-1-git-send-email-wgong@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we expire an inactive station, try to send it a deauth. This
helps if it's actually still around, and just has issues with
beacon distribution (or we do), and it will not also remove us.
Then, if we have shared state, this may not be reset properly,
causing problems; for example, we saw a case where aggregation
sessions weren't removed properly (due to the TX start being
offloaded to firmware and it relying on deauth for stop), causing
a lot of traffic to get lost due to the SN reset after remove/add
of the peer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-9-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We already assume that key is not NULL and dereference it in a few
other places before we check whether it is NULL, so the check is
unnecessary. Remove it.
Fixes: 96fc6efb9a ("mac80211: IEEE 802.11 Extended Key ID support")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-8-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case we got a fw restart while roaming from encrypted AP to
non-encrypted one, we might end up with hitting a warning on the pending
counter crypto_tx_tailroom_pending_dec having a non-zero value.
The following comment taken from net/mac80211/key.c explains the rational
for the delayed tailroom needed:
/*
* The reason for the delayed tailroom needed decrementing is to
* make roaming faster: during roaming, all keys are first deleted
* and then new keys are installed. The first new key causes the
* crypto_tx_tailroom_needed_cnt to go from 0 to 1, which invokes
* the cost of synchronize_net() (which can be slow). Avoid this
* by deferring the crypto_tx_tailroom_needed_cnt decrementing on
* key removal for a while, so if we roam the value is larger than
* zero and no 0->1 transition happens.
*
* The cost is that if the AP switching was from an AP with keys
* to one without, we still allocate tailroom while it would no
* longer be needed. However, in the typical (fast) roaming case
* within an ESS this usually won't happen.
*/
The next flow lead to the warning eventually reported as a bug:
1. Disconnect from encrypted AP
2. Set crypto_tx_tailroom_pending_dec = 1 for the key
3. Schedule work
4. Reconnect to non-encrypted AP
5. Add a new key, setting the tailroom counter = 1
6. Got FW restart while pending counter is set ---> hit the warning
While on it, the ieee80211_reset_crypto_tx_tailroom() func was merged into
its single caller ieee80211_reenable_keys (previously called
ieee80211_enable_keys). Also, we reset the crypto_tx_tailroom_pending_dec
and remove the counters warning as we just reset both.
Signed-off-by: Lior Cohen <lior2.cohen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-7-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we reach this point, the key cannot be NULL. Remove the condition
that suggests otherwise.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-6-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
"HE/HT/VHT" is a bit confusing since really the order of
development (and possible support) is different - change
this to "HT/VHT/HE".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-4-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This fixes was missed in parsing the vht capabilities max bw
support.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: e80d642552 ("mac80211: copy VHT EXT NSS BW Support/Capable data to station")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830114057.22197-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The noencrypt flag was intended to be set if the "frame was received
unencrypted" according to include/uapi/linux/nl80211.h. However, the
current behavior is opposite of this.
Cc: stable@vger.kernel.org
Fixes: 018f6fbf54 ("mac80211: Send control port frames over nl80211")
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Link: https://lore.kernel.org/r/20190827224120.14545-3-denkenz@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_deliver_skb_to_local_stack intercepts EAPoL frames if
mac80211 is configured to do so and forwards the contents over nl80211.
During this process some additional data is also forwarded, including
whether the frame was received encrypted or not. Unfortunately just
prior to the call to ieee80211_deliver_skb_to_local_stack, skb->cb is
cleared, resulting in incorrect data being exposed over nl80211.
Fixes: 018f6fbf54 ("mac80211: Send control port frames over nl80211")
Cc: stable@vger.kernel.org
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Link: https://lore.kernel.org/r/20190827224120.14545-2-denkenz@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the for-loop will spin forever if variable supported is
non-zero because supported is never changed. Fix this by adding in
the missing right shift of supported.
Addresses-Coverity: ("Infinite loop")
Fixes: 48cb39522a ("mac80211: minstrel_ht: improve rate probing for devices with static fallback")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190822122034.28664-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On some devices that only support static rate fallback tables sending rate
control probing packets can be really expensive.
Probing lower rates can already hurt throughput quite a bit. What hurts even
more is the fact that on mt76x0/mt76x2, single probing packets can only be
forced by directing packets at a different internal hardware queue, which
causes some heavy reordering and extra latency.
The reordering issue is mainly problematic while pushing lots of packets to
a particular station. If there is little activity, the overhead of probing is
neglegible.
The static fallback behavior is designed to pretty much only handle rate
control algorithms that use only a very limited set of rates on which the
algorithm switches up/down based on packet error rate.
In order to better support that kind of hardware, this patch implements a
different approach to rate probing where it switches to a slightly higher rate,
waits for tx status feedback, then updates the stats and switches back to
the new max throughput rate. This only triggers above a packet rate of 100
per stats interval (~50ms).
For that kind of probing, the code has to reduce the set of probing rates
a lot more compared to single packet probing, so it uses only one packet
per MCS group which is either slightly faster, or as close as possible to
the max throughput rate.
This allows switching between similar rates with different numbers of
streams. The algorithm assumes that the hardware will work its way lower
within an MCS group in case of retransmissions, so that lower rates don't
have to be probed by the high packets per second rate probing code.
To further reduce the search space, it also does not probe rates with lower
channel bandwidth than the max throughput rate.
At the moment, these changes will only affect mt76x0/mt76x2.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-4-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On hardware with static fallback tables (e.g. mt76x2), rate probing attempts
can be very expensive.
On such devices, avoid sampling rates slower than the per-group max throughput
rate, based on the assumption that the fallback table will take care of probing
lower rates within that group if the higher rates fail.
To further reduce unnecessary probing attempts, skip duplicate attempts on
rates slower than the max throughput rate.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The group number needs to be multiplied by the number of rates per group
to get the full rate index
Fixes: 5935839ad7 ("mac80211: improve minstrel_ht rate sorting by throughput & probability")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190820095449.45255-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
802.11ay specification defines Enhanced Directional Multi-Gigabit
(EDMG) STA and AP which allow channel bonding of 2 channels and more.
Introduce new NL attributes that are needed for enabling and
configuring EDMG support.
Two new attributes are used by kernel to publish driver's EDMG
capabilities to the userspace:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
When this attribute is not set it means driver does not support EDMG.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represent the channel bandwidth
configurations supported by the driver.
Additional two new attributes are used by the userspace for connect
command and for AP configuration:
NL80211_ATTR_WIPHY_EDMG_CHANNELS
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG
New rate info flag - RATE_INFO_FLAGS_EDMG, can be reported from driver
and used for bitrate calculation that will take into account EDMG
according to the 802.11ay specification.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Link: https://lore.kernel.org/r/1566138918-3823-2-git-send-email-ailizaro@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
he_spr_ie_elem is dereferenced before the NULL check. fix this by moving
the assignment after the check.
fixes commit 697f6c507c ("mac80211: propagate HE operation info into
bss_conf")
This was reported by the static code checker.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190813070712.25509-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Report timestamp for when sta becomes associated.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20190809180001.26393-2-greearb@candelatech.com
[fix ktime_get_boot_ns() to ktime_get_boottime_ns(), assoc_at type to u64]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the 802.11ax specification a new band is introduced, which
is also proposed by FCC for unlicensed use. This band is referred
to as 6GHz spanning frequency range from 5925 to 7125 MHz.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-2-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code generating the Tx Radiotap header when using tx_status_ext was
missing a field increment after setting the VHT bandwidth.
Fixes: 3d07ffcaf3 ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-4-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When reporting 80MHz, we need to set 4 and not 2 inside the corresponding
field inside the Tx Radiotap header.
Fixes: 3d07ffcaf3 ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-3-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When reporting legacy rates inside the TX Radiotap header we need to split
the check between "uses tx_statua_ext" and "is legacy rate". Not doing so
would make the code drop into the !tx_status_ext path.
Fixes: 3d07ffcaf3 ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The RX Radiotap header length was not calculated properly when reporting
legacy rates using tx_status_ext.
Fixes: 3d07ffcaf3 ("mac80211: add struct ieee80211_tx_status support to ieee80211_add_tx_radiotap_header")
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190807075949.32414-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of HE AP-STA link, ieee80211_send_nullfunc() will not
send the QOS NULL packet to check if AP is still associated.
In this case, probe_send_count will be non-zero and
ieee80211_sta_work() will later disassociate the AP, even
though no packet was ever sent.
Fix this by decrementing probe_send_count and not calling
ieee80211_send_nullfunc() in case of HE link, so that we
still wait for some time for the AP beacon to reappear and
don't disconnect right away.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Link: https://lore.kernel.org/r/20190703131848.22879-1-shay.bar@celeno.com
[clarify commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Store the OBSS PD parameters inside bss_conf when bringing up an AP and/or
when a station connects to an AP. This allows the driver to configure the
HW accordingly.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190730163701.18836-3-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This came up in fuzz testing, and really we don't consider
all-zeroes to be a valid MAC address in most places, so
also reject it here to avoid confusion later on.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Link: https://lore.kernel.org/r/1563959770-21570-1-git-send-email-periyasa@codeaurora.org
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The return from ieee80211_get_sband can potentially be a null pointer, so
it seems prudent to add a null check to avoid a null pointer dereference
on sband.
Addresses-Coverity: ("Dereference null return")
Fixes: 2ab4587675 ("mac80211: add support for the ADDBA extension element")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190730143205.14261-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Revert this for now, it has been reported multiple times that it
completely breaks connectivity on various devices.
Cc: stable@vger.kernel.org
Fixes: 8dbb000ee7 ("mac80211: set NETIF_F_LLTX when using intermediate tx queues")
Reported-by: Jean Delvare <jdelvare@suse.de>
Reported-by: Peter Lebbing <peter@digitalbrains.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
HE allows peers to negotiate the aggregation fragmentation level to be used
during transmission. The level can be 1-3. The Ext element is added behind
the ADDBA request inside the action frame. The responder will then reply
with the same level or a lower one if the requested one is not supported.
This patch only handles the negotiation part as the ADDBA frames get passed
to the ATH11k firmware, which does the rest of the magic for us aswell as
generating the requests.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190729104512.27615-1-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Upon a successful assoc a station shall store the content of the HE
operation element inside bss_conf so that the driver can setup the
hardware accordingly.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20190729102342.8659-2-john@phrozen.org
[use struct copy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In a very similar spirit to commit c470bdc1aa ("mac80211: don't WARN
on bad WMM parameters from buggy APs"), an AP may not transmit a
fully-formed WMM IE. For example, it may miss or repeat an Access
Category. The above loop won't catch that and will instead leave one of
the four ACs zeroed out. This triggers the following warning in
drv_conf_tx()
wlan0: invalid CW_min/CW_max: 0/0
and it may leave one of the hardware queues unconfigured. If we detect
such a case, let's just print a warning and fall back to the defaults.
Tested with a hacked version of hostapd, intentionally corrupting the
IEs in hostapd_eid_wmm().
Cc: stable@vger.kernel.org
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20190726224758.210953-1-briannorris@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement the basics required for supporting high efficiency with mesh:
include HE information elements in beacons, probe responses, and peering
action frames, and check for compatible HE configurations when peering.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Forwarded: https://patchwork.kernel.org/patch/11029299/
Link: https://lore.kernel.org/r/20190724163359.3507-2-sven@narfation.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add IEEE80211_KEY_FLAG_GENERATE_MMIE flag to ieee80211_key_flags in order
to allow the driver to notify mac80211 to generate MMIE and that it
requires sequence number generation only.
This is a preliminary patch to add BIP_CMAC_128 hw support to mt7615
driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/dfe275f9aa0f1cc6b33085f9efd5d8447f68ad13.1563228405.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to mac80211 for parsing SPR elements as per
P802.11ax_D4.0 section 9.4.2.241.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190618061915.7102-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to ieee80211_add_tx_radiotap_header() for handling rates
reported via ieee80211_tx_status. This allows us to also report HE rates.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190714154419.11854-4-john@phrozen.org
[remove text about 60 GHz, mac80211 doesn't support it, fix endianness issue]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 33d915d9e8 ("{nl,mac}80211: allow 4addr AP operation on
crypto controlled devices") has introduced a change which allows
4addr operation on crypto controlled devices (ex: ath10k). This
change has inadvertently impacted the interface combinations logic
on such devices.
General rule is that software interfaces like AP/VLAN should not be
listed under supported interface combinations and should not be
considered during validation of these combinations; because of the
aforementioned change, AP/VLAN interfaces(if present) will be checked
against interfaces supported by the device and blocks valid interface
combinations.
Consider a case where an AP and AP/VLAN are up and running; when a
second AP device is brought up on the same physical device, this AP
will be checked against the AP/VLAN interface (which will not be
part of supported interface combinations of the device) and blocks
second AP to come up.
Add a new API cfg80211_iftype_allowed() to fix the problem, this
API works for all devices with/without SW crypto control.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Fixes: 33d915d9e8 ("{nl,mac}80211: allow 4addr AP operation on crypto controlled devices")
Link: https://lore.kernel.org/r/1563779690-9716-1-git-send-email-mpubbise@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extended Key ID allows A-MPDU sessions while rekeying as long as each
A-MPDU aggregates only MPDUs with one keyid together.
Drivers able to segregate MPDUs accordingly can tell mac80211 to not
stop A-MPDU sessions when rekeying by setting the new flag
IEEE80211_HW_AMPDU_KEYBORDER_SUPPORT.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20190629195015.19680-3-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
1) Drop IEEE80211_HW_EXT_KEY_ID_NATIVE and let drivers directly set
the NL80211_EXT_FEATURE_EXT_KEY_ID flag.
2) Drop IEEE80211_HW_NO_AMPDU_KEYBORDER_SUPPORT and simply assume all
drivers are unable to handle A-MPDU key borders.
The new Extended Key ID API now requires all mac80211 drivers to set
NL80211_EXT_FEATURE_EXT_KEY_ID when they implement set_key() and can
handle Extended Key ID. For drivers not providing set_key() mac80211
itself enables Extended Key ID support, using the internal SW crypto
services.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20190629195015.19680-2-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since ieee80211_tx_dequeue() must not be called with softirqs enabled
(i.e. from process context without proper disable of bottom halves),
we add a wrapper that disables bottom halves before calling
ieee80211_tx_dequeue()
The new function is named ieee80211_tx_dequeue_ni() just as all other
from-process-context versions found in mac80211.
The documentation of ieee80211_tx_dequeue() is also updated so it
mentions that the function should not be called from process context.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Link: https://lore.kernel.org/r/20190617200140.6189-1-erik.stromdahl@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The remove_sta_debugfs callback in struct rate_control_ops is no longer
used by any driver, as there is no need for it (the debugfs directory is
already removed recursivly by the mac80211 core.) Because no one needs
it, just remove it to keep anyone else from accidentally using it in the
future.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190612142658.12792-5-gregkh@linuxfoundation.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This low level driver can find it useful to get the vif
when a remain on channel session is cancelled.
iwlwifi will need this soon.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20190723180001.5828-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_set_wmm_default() normally sets up the initial CW min/max for
each queue, except that it skips doing this if the driver doesn't
support ->conf_tx. We still end up calling drv_conf_tx() in some cases
(e.g., ieee80211_reconfig()), which also still won't do anything
useful...except it complains here about the invalid CW parameters.
Let's just skip the WARN if we weren't going to do anything useful with
the parameters.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20190718015712.197499-1-briannorris@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
David S. Miller
Jouni Malinen
Wen Gong
Johannes Berg
Luca Coelho
Lior Cohen
Mordechay Goodstein
Denis Kenzior
Colin Ian King
Felix Fietkau
Alexei Avshalom Lazar
John Crispin
Ben Greear
Arend van Spriel
Shay Bar
Karthikeyan Periyasamy
Brian Norris
Sven Eckelmann
Lorenzo Bianconi
Manikanta Pubbisetty
Alexander Wetzel
Erik Stromdahl
Greg Kroah-Hartman
Emmanuel Grumbach