In gadget mode, musb->is_active should be set only when connected to the
host. musb_g_reset() already takes care of it.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Set SEL control urbs cannot be sent to a device in unconfigured state.
This patch adds a check in usb_req_set_sel() to ensure the usb device's
state is USB_STATE_CONFIGURED.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: Martin MOKREJS <mmokrejs@gmail.com>
Suggested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The halted state of a endpoint cannot be cleared over CLEAR_HALT from a
user process, because the stopped_td variable was overwritten in the
handle_stopped_endpoint() function. So the xhci_endpoint_reset() function will
refuse the reset and communication with device can not run over this endpoint.
https://bugzilla.kernel.org/show_bug.cgi?id=60699
Signed-off-by: Florian Wolter <wolly84@web.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When a device signals remote wakeup on a roothub, and the suspend change
bit is set, the host controller driver must not give control back to the
USB core until the port goes back into the active state.
EHCI accomplishes this by waiting in the get port status function until
the PORT_RESUME bit is cleared:
/* stop resume signaling */
temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
ehci_writel(ehci, temp, status_reg);
clear_bit(wIndex, &ehci->resuming_ports);
retval = ehci_handshake(ehci, status_reg,
PORT_RESUME, 0, 2000 /* 2msec */);
Similarly, the xHCI host should wait until the port goes into U0, before
passing control up to the USB core. When the port transitions from the
RExit state to U0, the xHCI driver will get a port status change event.
We need to wait for that event before passing control up to the USB
core.
After the port transitions to the active state, the USB core should time
a recovery interval before it talks to the device. The length of that
recovery interval is TRSMRCY, 10 ms, mentioned in the USB 2.0 spec,
section 7.1.7.7. The previous xHCI code (which did not wait for the
port to go into U0) would cause the USB core to violate that recovery
interval.
This bug caused numerous USB device disconnects on remote wakeup under
ChromeOS and a Lynx Point LP xHCI host that takes up to 20 ms to move
from RExit to U0. ChromeOS is very aggressive about power savings, and
sets the autosuspend_delay to 100 ms, and disables USB persist.
I attempted to replicate this bug with Ubuntu 12.04, but could not. I
used Ubuntu 12.04 on the same platform, with the same BIOS that the bug
was triggered on ChromeOS with. I also changed the USB sysfs settings
as described above, but still could not reproduce the bug under Ubuntu.
It may be that ChromeOS userspace triggers this bug through additional
settings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If a command on the command ring needs to be cancelled before it is handled
it can be turned to a no-op operation when the ring is stopped.
We want to store the command ring enqueue pointer in the command structure
when the command in enqueued for the cancellation case.
Some commands used to store the command ring dequeue pointers instead of enqueue
(these often worked because enqueue happends to equal dequeue quite often)
Other commands correctly used the enqueue pointer but did not check if it pointed
to a valid trb or a link trb, this caused for example stop endpoint command to timeout in
xhci_stop_device() in about 2% of suspend/resume cases.
This should also solve some weird behavior happening in command cancellation cases.
This patch is based on a patch submitted by Sarah Sharp to linux-usb, but
then forgotten:
http://marc.info/?l=linux-usb&m=136269803207465&w=2
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c04 "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
When a command times out, the command ring is first aborted,
and then stopped. If the command ring is empty when it is stopped
the stop event will point to next command which is not yet set.
xHCI tries to handle this next event often causing an oops.
Don't handle command completion events on stopped cmd ring if ring is
empty.
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c04 "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reported-by: Giovanni <giovanni.nervi@yahoo.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Move probe out of __init section and don't use platform_driver_probe
which cannot be used with deferred probing.
Since commit e9354576 ("gpiolib: Defer failed gpio requests by default")
and 04bf3011 ("regulator: Support driver probe deferral") this driver
might return -EPROBE_DEFER if a gpio_request or regulator_get fails.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move probe out of __init section and don't use platform_driver_probe
which cannot be used with deferred probing.
Since commit e9354576 ("gpiolib: Defer failed gpio requests by default")
this driver might return -EPROBE_DEFER if a gpio_request fails.
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here's first set of fixes for v3.12-rc series, patches have
been soaking in linux-usb for a while now.
We have the usual sparse and build warnings, a Kconfig fix
to a mismerge on dwc3 Kconfig, fix for a possible memory leak
in dwc3, s3c-hsotg won't disconnect when bus goes idle, locking
fix in mv_u3d_core, endpoint disable fix in f_mass_storage.
We also have one device ID added to dwc3's PCI glue layer in order
to support Intel's BayTrail devices.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJSOH9nAAoJEIaOsuA1yqRElTcQALIZuTv00Lg4Sts4tHHVO3KB
qvQEcv9cBZFtQkD053ufAkJ7uRMkl7Ew5jzJj3AFhLwQ8d0eOY6O9lARG2mZdJf1
99mCw/BgLAs9q9xgAQvuVOnmXNsi/+A5LQrbcfUG5hoecVZZhfPKZydkUGRE4+be
UG7T0D72saa3GfnvuHGv1Z5i4IEijx6amzPaFuDQzsRNjpdEn28lqvp5nN/amKuw
Bda++9o5DPEu/I+MseTx8eSUfrvqR7khFOxJeNlhJxkgoDQiEXaOQEbgIj1bLcEx
bs7RF28r0Rs75seImD+0TiXlGJVr/kv2EJ5RI4qgZ+MRxu8lrfeUWHNCdIiAI62d
rqwqnxL0AZiHuQdN2AEle9VJsoBaDw2sB8GiDQ3ZHms3InEVaVtAIpd+E0gXdf0y
W713iZqf/9zcfuoTA0y8G/foCaWuUXr89kpv5mpGejAJBLbHRk/0hEQzW4Y/eeMb
RbKjWFseD2bEWGlRqIcd2E73AKM8TccjmEc+khj/9kZzbrF+uoUbUrULhkKHp190
4fBKVT/0y4s63zadmkebN91vUBpLtnYIykXU4sDm79GlImMXJA/RLmkbfCtaDyAQ
7rEknrLEpvMVe6VbSMiitgmZb8qwy2kemhGCGbJ6e4jU7BKThUTE1gt8SlJhQm1M
W2SoxhxQRKxXtQT/xkxt
=51X+
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.12-rc2
Here's first set of fixes for v3.12-rc series, patches have
been soaking in linux-usb for a while now.
We have the usual sparse and build warnings, a Kconfig fix
to a mismerge on dwc3 Kconfig, fix for a possible memory leak
in dwc3, s3c-hsotg won't disconnect when bus goes idle, locking
fix in mv_u3d_core, endpoint disable fix in f_mass_storage.
We also have one device ID added to dwc3's PCI glue layer in order
to support Intel's BayTrail devices.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Right after the musb_hdrc driver is loaded, the otg default state
is a_idle, and Mode=Host, which are set by musb_host_setup().
This causes the following kernel message during musb gadget
enumeration.
CAUTION: musb: Babble Interrupt Occurred
This patch sets the otg default state to b_idle, and its Mode to
Peripheral.
It has been validated on TI AM335x GP EVM USB0 port with g_zero.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to Prolific, several (unauthorized) cheap and less functional
clones of the PL2303HX chip are in circulation. [1]
I've had the chance to test such a cloned device and it turned out that
it doesn't support any baud rates above 115200 baud (original: 6 Mbaud)
It also doesn't support the divisior based baud rate encoding method,
so no continuous baud rate adjustment is possible.
Nevertheless, these devices have been working (unintentionally) with
the driver up to commit 61fa8d694b ("pl2303: also use the divisor based
baud rate encoding method for baud rates < 115200 with HX chips"), and
this commit broke support for them.
Fortunately, it is pretty simple to distinguish between the original
and the cloned HX chips, so I've added a check and an extra chip type
to keep the clones working.
The same check is used by the latest Prolific Windows driver, so it
should be solid.
[1] http://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225&pcid=41
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the MODULE_AUTHOR field of the Faraday OTG drivers to reflect
current maintainers email address.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 428aac8a81.
This isn't quite ready for 3.12, we need some more EHCI driver changes
that are just now showing up. So revert this for now, and queue it up
later for 3.13.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC2 databook indicates if the core sets "ErlySusp" bit, an idle state has been
detected on the USB for 3 ms. This situation can be occurred when waiting
a request from user daemon. So, we should keep the connection between udc and
gadget even though this interrupt is occurred.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After driver conversion to udc_start/udc_stop infrastructure (commit
"usb:hsotg:samsung: Use new udc_start and udc_stop callbacks"
f65f0f1098) the gadget unregistration function is almost always called
with 'driver' parameter being NULL, what caused that the unregistration
code has not been executed at all. This is a leftover from the earlier
verison of this function (which used simple start/stop interface), where
driver parameter was obligatory.
This patch removes the NULL check for the 'driver' pointer and removes
all dereferences of it. It also moves disabling voltage regulators out
of the atomic context, because handling regulators (which are usually
i2c devices) might require sleeping.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Gadgets endpoint driver data is a criteria to judge that
whether the endpoints are in use or not. When gadget gets
assigned an endpoint from endpoint list, they check its
driver data if the driver data is NULL.
If the driver data is not NULL then they regard it as in use.
Therefore all of gadgets should reset their endpoints driver
data to NULL as they are disabled. Otherwise it causes a leak
of endpoint resource.
Signed-off-by: Peter Oh <poh@broadcom.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Local symbols used in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The function returns a pointer. Hence return NULL instead of 0.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If dwc3_gadget_init_endpoint() fails after allocate some of the eps, we
need to free their memory to avoid leak.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is required by the OMAP glue driver, but it already depends
on it. The core driver should not depend on it. This will
allow the use of the PCI glue driver again.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
They are only called by '__ref' function multi_bind(), and they will
call '__init' functions, so recommend to let them '__ref' too.
The related warnings:
WARNING: drivers/usb/gadget/g_multi.o(.text+0xded6): Section mismatch in reference from the variable .LM2921 to the variable .init.text:_rndis_do_config
The function .LM2921() references
the variable __init _rndis_do_config.
This is often because .LM2921 lacks a __init
annotation or the annotation of _rndis_do_config is wrong.
WARNING: drivers/usb/gadget/g_multi.o(.text+0xdf16): Section mismatch in reference from the variable .LM2953 to the variable .init.text:_cdc_do_config
The function .LM2953() references
the variable __init _cdc_do_config.
This is often because .LM2953 lacks a __init
annotation or the annotation of _cdc_do_config is wrong.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This fixes commit a38a275030
(usb: gadget: cdc2: convert to new interface of f_ecm)
The invocation of usb_get_function_instance() is in cdc_bind()
and should not be repeated in cdc_do_config().
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes a NULL pointer dereference and a WARN_ON in
dummy-hcd. These things were the result of moving to the UDC core
framework, and possibly of changes to that framework.
Now unloading a gadget driver causes the UDC to be stopped after the
gadget driver is unbound, not before. Therefore the "driver" argument
to dummy_udc_stop() can be NULL, so we must not try to print the
driver's name without checking first.
Also, the UDC framework automatically unregisters the gadget when the
UDC is deleted. Therefore a sysfs attribute file attached to the
gadget must be removed before the UDC is deleted, not after.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
mv_u3d_nuke() expects to be calles with ep->u3d->lock held,
because mv_u3d_done() does. But mv_u3d_ep_disable() calls it
without lock that can lead to unpleasant consequences.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull aio changes from Ben LaHaise:
"First off, sorry for this pull request being late in the merge window.
Al had raised a couple of concerns about 2 items in the series below.
I addressed the first issue (the race introduced by Gu's use of
mm_populate()), but he has not provided any further details on how he
wants to rework the anon_inode.c changes (which were sent out months
ago but have yet to be commented on).
The bulk of the changes have been sitting in the -next tree for a few
months, with all the issues raised being addressed"
* git://git.kvack.org/~bcrl/aio-next: (22 commits)
aio: rcu_read_lock protection for new rcu_dereference calls
aio: fix race in ring buffer page lookup introduced by page migration support
aio: fix rcu sparse warnings introduced by ioctx table lookup patch
aio: remove unnecessary debugging from aio_free_ring()
aio: table lookup: verify ctx pointer
staging/lustre: kiocb->ki_left is removed
aio: fix error handling and rcu usage in "convert the ioctx list to table lookup v3"
aio: be defensive to ensure request batching is non-zero instead of BUG_ON()
aio: convert the ioctx list to table lookup v3
aio: double aio_max_nr in calculations
aio: Kill ki_dtor
aio: Kill ki_users
aio: Kill unneeded kiocb members
aio: Kill aio_rw_vect_retry()
aio: Don't use ctx->tail unnecessarily
aio: io_cancel() no longer returns the io_event
aio: percpu ioctx refcount
aio: percpu reqs_available
aio: reqs_active -> reqs_available
aio: fix build when migration is disabled
...
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull powerpc updates from Ben Herrenschmidt:
"Here's the powerpc batch for this merge window. Some of the
highlights are:
- A bunch of endian fixes ! We don't have full LE support yet in that
release but this contains a lot of fixes all over arch/powerpc to
use the proper accessors, call the firmware with the right endian
mode, etc...
- A few updates to our "powernv" platform (non-virtualized, the one
to run KVM on), among other, support for bridging the P8 LPC bus
for UARTs, support and some EEH fixes.
- Some mpc51xx clock API cleanups in preparation for a clock API
overhaul
- A pile of cleanups of our old math emulation code, including better
support for using it to emulate optional FP instructions on
embedded chips that otherwise have a HW FPU.
- Some infrastructure in selftest, for powerpc now, but could be
generalized, initially used by some tests for our perf instruction
counting code.
- A pile of fixes for hotplug on pseries (that was seriously
bitrotting)
- The usual slew of freescale embedded updates, new boards, 64-bit
hiberation support, e6500 core PMU support, etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc: Correct FSCR bit definitions
powerpc/xmon: Fix printing of set of CPUs in xmon
powerpc/pseries: Move lparcfg.c to platforms/pseries
powerpc/powernv: Return secondary CPUs to firmware on kexec
powerpc/btext: Fix CONFIG_PPC_EARLY_DEBUG_BOOTX on ppc32
powerpc: Cleanup handling of the DSCR bit in the FSCR register
powerpc/pseries: Child nodes are not detached by dlpar_detach_node
powerpc/pseries: Add mising of_node_put in delete_dt_node
powerpc/pseries: Make dlpar_configure_connector parent node aware
powerpc/pseries: Do all node initialization in dlpar_parse_cc_node
powerpc/pseries: Fix parsing of initial node path in update_dt_node
powerpc/pseries: Pack update_props_workarea to map correctly to rtas buffer header
powerpc/pseries: Fix over writing of rtas return code in update_dt_node
powerpc/pseries: Fix creation of loop in device node property list
powerpc: Skip emulating & leave interrupts off for kernel program checks
powerpc: Add more exception trampolines for hypervisor exceptions
powerpc: Fix location and rename exception trampolines
powerpc: Add more trap names to xmon
powerpc/pseries: Add a warning in the case of cross-cpu VPA registration
powerpc: Update the 00-Index in Documentation/powerpc
...
Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlIPcACgkQMUfUDdst+ynUMwCaAnITsxyDXYQ4DqEsz8EcOtMk
718AoLrgnUZs3B+70AT34DVktg4HSThk
=USl9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
Here is the big char/misc driver pull request for 3.12-rc1
Lots of driver updates all over the char/misc tree, full details in the
shortlog below.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlH58ACgkQMUfUDdst+ymTGwCdH1BmMdypyjUBxJEoWNDUuwXn
/AQAoKt329vmB6qn41rvaTilHHYUXS7H
=ovaW
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc patches from Greg KH:
"Here is the big char/misc driver pull request for 3.12-rc1
Lots of driver updates all over the char/misc tree, full details in
the shortlog"
* tag 'char-misc-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (62 commits)
drivers: uio: Kconfig: add MMU dependancy for UIO
drivers: uio: Add driver for Humusoft MF624 DAQ PCI card
drivers: uio_pdrv_genirq: use dev_get_platdata()
drivers: uio_pruss: use dev_get_platdata()
drivers: uio_dmem_genirq: use dev_get_platdata()
drivers: parport: Kconfig: exclude h8300 for PARPORT_PC
drivers: misc: ti-st: fix potential race if st_kim_start fails
Drivers: hv: vmbus: Do not attempt to negoatiate a new version prematurely
misc: vmw_balloon: Remove braces to fix build for clang.
Drivers: hv: vmbus: Fix a bug in the handling of channel offers
vme: vme_ca91cx42.c: fix to pass correct device identity to free_irq()
VMCI: Add support for virtual IOMMU
VMCI: Remove non-blocking/pinned queuepair support
uio: uio_pruss: remove unnecessary platform_set_drvdata()
parport: amiga: remove unnecessary platform_set_drvdata()
vme: vme_vmivme7805.c: add missing __iomem annotation
vme: vme_ca91cx42.c: add missing __iomem annotation
vme: vme_tsi148.c: add missing __iomem annotation
drivers/misc/hpilo: Correct panic when an AUX iLO is detected
uio: drop unused vma_count member in uio_device struct
...
Here's the big USB driver pull request for 3.12-rc1
Lots of USB driver fixes and updates. Nothing major, just the normal
xhci, gadget, and other driver changes. Full details in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlJJ8ACgkQMUfUDdst+ymBAwCgg8czTAuwpCCK7H8LHnC2BsMj
dtUAnjDisrbw4qWSXaaA/sfgSZjKW5G4
=Tman
-----END PGP SIGNATURE-----
Merge tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big USB driver pull request for 3.12-rc1
Lots of USB driver fixes and updates. Nothing major, just the normal
xhci, gadget, and other driver changes. Full details in the shortlog"
* tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (352 commits)
usbcore: fix incorrect type in assignment in descriptors_changed()
usbcore: compare and release one bos descriptor in usb_reset_and_verify_device()
ehci: remove debugging statement with ehci statistics in ehci_stop()
ehci: remove duplicate debug_async_open() prototype in ehci-dbg.c
ehci: enable debugging code when CONFIG_DYNAMIC_DEBUG is set
ehci: remove ehci_vdbg() verbose debugging statements
Documentation sysfs-bus-usb: Document which files are used by libusb
Documentation sysfs-bus-usb: Document the speed file used by libusb
Documentation sysfs-bus-usb: Move files with known users to stable
USB: fix build error when CONFIG_PM_SLEEP isn't enabled
usb: r8a66597-hcd: use platform_{get,set}_drvdata()
usb: phy-tegra-usb: use platform_{get,set}_drvdata()
usb: acm gadget: Null termintate strings table
dma: cppi41: off by one in desc_to_chan()
xhci: Fix warning introduced by disabling runtime PM.
dev-core: fix build break when DEBUG is enabled
USB: OHCI: Allow runtime PM without system sleep
usb: ohci-at91: remove unnecessary dev_set_drvdata()
usb: renesas_usbhs: use platform_{get,set}_drvdata()
usb: fotg210-udc: use platform_{get,set}_drvdata()
...
This patch fixes the incorrect assignment of a variable with type 'le16'
to a variable with type 'unsigned int'.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In usb_reset_and_verify_device(), hub_port_init() allocates a new bos
descriptor to hold the value read by the device. The new bos descriptor
has to be compared with the old one in order to figure out if device 's
firmware has changed in which case the device has to be reenumerated.
In the original code, none of the two descriptors was deallocated leading
to memory leaks.
This patch compares the old bos descriptor with the new one to detect change
in firmware and releases the newly allocated bos descriptor to prevent memory
leak.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Reported-by: Martin MOKREJS <mmokrejs@gmail.com>
Tested-by: Martin MOKREJS <mmokrejs@gmail.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the ehci statictics information output in ehci_stop()
because they do not provide interesting info. At any case, the current
statistics can be viewed by reading the 'registers' file in debugfs.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the duplicate of debug_async_open() prototype following
three lines below the debug_async_open() declaration.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debugging code for ehci is enabled to run if the DEBUG flag is defined.
This patch enables the debugging code also when the kernel is configured
with dynamic debugging on.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes ehci_vdbg debugging statements from EHCI host controller
driver because they produce too much information, lowering the signal to noise
ratio when debugging, and because they are not used anymore.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadget strings table should be null terminated.
usb_gadget_get_string() loops through the table
expecting a null at the end of the list.
Signed-off-by: Graham Williams <gwilli@broadcom.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
This first patch should fix the build breakage Sedat Dilek reported.
Apologizes for not including this patch before commit
0730d52a86 "xhci:prevent "callbacks suppressed"
when debug is not enabled"
The second patch fixes a new build warning introduced by commit
c8476fb855 "usb: xhci: Disable runtime PM suspend
for quirky controllers", which was caught by the 0day build system.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=siJK
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2013-08-27-15-07' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xhci: Fix build breakage and new warnings.
Hi Greg,
This first patch should fix the build breakage Sedat Dilek reported.
Apologizes for not including this patch before commit
0730d52a86 "xhci:prevent "callbacks suppressed"
when debug is not enabled"
The second patch fixes a new build warning introduced by commit
c8476fb855 "usb: xhci: Disable runtime PM suspend
for quirky controllers", which was caught by the 0day build system.
Sarah Sharp
Since ohci-hcd supports runtime PM, the .pm field in its pci_driver
structure should be protected by CONFIG_PM rather than
CONFIG_PM_SLEEP.
Without this change, OHCI controllers won't do runtime suspend if
system suspend or hibernation isn't enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a set of important fixes for v3.12 merge
window which have been pending in the mailing list
for quite some time.
We have use-after-free fixes, signedness fixes,
more of HAS_DMA dependencies, fixes for NULL pointer
deferences, build fixes and some other fixes to
the musb driver caused by recent patches.
Patches are quite small and contain valuable fixes
which will give us a much better -rc1 release.
Please consider merging
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJSHQe5AAoJEIaOsuA1yqREgaUP/3wnPuYiP5lvNb60B/YcKlbV
0Qyw/6yEz2+H0cbUsGWxqNTqX6bj72vPuNyAM4EGCs26ZJG8Jz6fFpJ7xIQCsGaY
7iGo/RiGvCNQj15r/QBjM0mMIQSG8QwU/sFl45Ai/0g3sbUdKBdHVm4lRMV1Q9EG
+vSUvmkuidXZ2PuF2k2goVofeQ7NOPJSxvP91Vt3DQK2CIICol8J+IXgMkJUGTOW
xR7L5lRIMTj7F0PWY63x8HrEQdGqlXjvcq+/FQOd++ErUkDMcQ6q/G1vZeHqu9aD
kSMDoJOrjYM2qwW29JH9rR7y4F1ac+XYQj3MoNd95GRWMWWx1mXqIGYbTc8gel/S
1h0Vu2qVsFsWZTNRESY8wWSKb8ogoubMQX+PNpwZZnrqJBEk7/WpnX42gF209tLc
xYnExU4ZIAES2j5QZ4eJbFAo5RiqWQ4EVVTscWTVZ1zFf06u6Bqa+Nk6GB+qS91U
QOKonQi9SZRx4sMjt7H6kYbsNBIslplSZCqFcory6XTbtpDhoTlyx9e11rnWV8wC
vSQPpc2fyVlPNaJE7UQhC2U2MHiXCsT9KGYr5CD5JKMaNmcBSSMVDGvUZQbuu5wA
KutERTnU+x+KHwtnoA7QfcT97SR8cothVRa1+CrvzkPd8hQJGvai29RumLPjM3da
DWqj5VmDljtX9e4kdDiq
=QceB
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.12-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.12 merge window (part 2)
Here's a set of important fixes for v3.12 merge
window which have been pending in the mailing list
for quite some time.
We have use-after-free fixes, signedness fixes,
more of HAS_DMA dependencies, fixes for NULL pointer
deferences, build fixes and some other fixes to
the musb driver caused by recent patches.
Patches are quite small and contain valuable fixes
which will give us a much better -rc1 release.
Please consider merging
Signed-of-by: Felipe Balbi <balbi@ti.com>
Convert the usbsorage sysfs attribute to use the _RW macro to make it
easier to determine the permissions for the file.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter's automatic Smatch checker found an anomaly in the ux500
MUSB driver, whereby board data was checked before use in all but one
occasion. It is believed that it needs to be checked every time.
Smatch complaint:
drivers/usb/musb/ux500_dma.c:335 ux500_dma_controller_start()
error: we previously assumed 'data' could be null (see line 313)
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The "goto out" statements were wrong. We aren't holding any locks at
that point so we should return directly.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
"ret" needs to be signed for the error handling to work.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ffs_data_put() can sometimes free "ffs" so I have moved the call down
a line below the dereference.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The call to put_dev() releases "dev". Hopefully, we don't need to set
the state to STATE_DEV_DISABLED anyway so I have removed those lines.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Hi Greg,
Here's three low-priority bug fixes that should be queued for 3.12.
They disable runtime PM for hosts that need the XHCI_RESET_ON_RESUME
quirk, fix USB 2.0 Link PM on hosts that don't have BESL support, and
prevent a bunch of log spam.
Please pull into usb-next for 3.12.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=XFdI
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2013-08-27' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xhci: Bug fixes for 3.12.
Hi Greg,
Here's three low-priority bug fixes that should be queued for 3.12.
They disable runtime PM for hosts that need the XHCI_RESET_ON_RESUME
quirk, fix USB 2.0 Link PM on hosts that don't have BESL support, and
prevent a bunch of log spam.
Please pull into usb-next for 3.12.
Sarah Sharp
Commit 94ae9843 (usb: phy: rename all phy drivers to phy-$name-usb.c)
renamed drivers/usb/phy/otg_fsm.h to drivers/usb/phy/phy-fsm-usb.h
but changed drivers/usb/phy/phy-fsm-usb.c to include not existing
"phy-otg-fsm.h" instead of new "phy-fsm-usb.h". This breaks building:
...
drivers/usb/phy/phy-fsm-usb.c:32:25: fatal error: phy-otg-fsm.h: No such file or directory
compilation terminated.
make[3]: *** [drivers/usb/phy/phy-fsm-usb.o] Error 1
This commit also missed to modify drivers/usb/phy/phy-fsl-usb.h
to include new "phy-fsm-usb.h" instead of "otg_fsm.h" resulting
in another build breakage:
...
In file included from drivers/usb/phy/phy-fsl-usb.c:46:0:
drivers/usb/phy/phy-fsl-usb.h:18:21: fatal error: otg_fsm.h: No such file or directory
compilation terminated.
make[3]: *** [drivers/usb/phy/phy-fsl-usb.o] Error 1
Fix both issues.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert all USB gadget sysfs attributes to use the _RO or _RW variants,
to make them easier to audit and ensure that the permissions are
correct.
Note, two are left using the DEVICE_ATTR() macro, as there is no
DEVICE_ATTR_WO() in Linus's tree, that will happen after 3.12-rc1 is
out, a follow-on patch will be sent then.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
--
drivers/usb/gadget/composite.c | 8 +++-----
drivers/usb/gadget/dummy_hcd.c | 8 ++++----
drivers/usb/gadget/f_mass_storage.c | 14 ++++++--------
drivers/usb/gadget/net2272.c | 4 ++--
drivers/usb/gadget/net2280.c | 18 +++++++++---------
drivers/usb/gadget/storage_common.c | 25 ++++++++++++-------------
drivers/usb/gadget/udc-core.c | 14 +++++++-------
7 files changed, 43 insertions(+), 48 deletions(-)
This is what I observe:
On the first connect, the musb starts with DEVCTL.Session set. On
disconnect, musb_core calls try_idle. That functions removes the Session
bit signalizing that the session is over (something that only in OTG is
required). A new device, that is plugged, is no longer recognized.
I've setup a timer and checked the DEVCTL register and I haven't seen a
change in VBus and I saw the B-Device bit set. After setting the IDDIG
into A mode and forcing the device to behave like a A device, I didn't
see a change.
Neither VBUS goes to 0b11 nor does a session start request comes.
In the TI-v3.2 kernel they skip to call musb_platform_try_idle() in the
OTG_STATE_A_WAIT_BCON state while not in OTG mode.
Since the second port hast a standard A plug the patch changes the port
to run in host mode only and skips the timer which would remove
DEVCTL.Session so we can reconnect to another device later.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Quite early on init there is an vbus / drvvbus interrupt comming and the
dsps code sets is_active to one. As a result we see a lot of
|musb_bus_suspend 2459: trying to suspend as a_wait_bcon while active
until a device is plugged in with pm_runtime enabled in the kernel.
After checking davinci, am35, da8xx I noticed that dsps is actually the
only one doing this.
So remove it and we won't flooded with mesages and the idle port can be
suspended.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This relfects the code and dts requires changes due to recent .dts
binding updates:
- use mg prefix for the Metor Graphics specific attributes
- use power in mA not in mA/2 as specifed in the USB2.0 specification
- remove the child node for USB. This is driver specific on won't be
reflected in the device tree
- use the "mentor" prefix instead of "mg".
- use "dr_mode" istead of "mg,port-mode" for the port mode. The former
is used by a few other drivers.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb_shutdown() removes always USB host and device.
musb_init_controller() adds host and device depending on port_mode. If
port mode is set to HOST then the removal of UDC leads only to:
|(NULL device *): gadget not registered.
and nothing else happens. If port mode is set to DEVICE and we remove
the host then we oops in usb_remove_hcd().
This patch ensures that we only remove host in OTG/host mode and device
only in OTG/device mode to avoid any trouble.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
devm_ioremap_resource returns an ERR_PTR value, not NULL, on failure.
Furthermore, the value returned by devm_ioremap_resource should be tested.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1;
statement S;
@@
*e = devm_ioremap_resource(...);
if (!e1) S
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If NO_DMA=y:
drivers/built-in.o: In function `net2272_done':
drivers/usb/gadget/net2272.c:386: undefined reference to `usb_gadget_unmap_request'
drivers/built-in.o: In function `net2272_queue':
drivers/usb/gadget/net2272.c:848: undefined reference to `usb_gadget_map_request'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If NO_DMA=y:
drivers/built-in.o: In function `sudmac_free_channel':
drivers/usb/gadget/r8a66597-udc.c:676: undefined reference to `usb_gadget_unmap_request'
drivers/built-in.o: In function `sudmac_alloc_channel':
drivers/usb/gadget/r8a66597-udc.c:666: undefined reference to `usb_gadget_map_request'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If NO_DMA=y:
drivers/built-in.o: In function `fusb300_set_idma':
drivers/usb/gadget/fusb300_udc.c:946: undefined reference to `usb_gadget_map_request'
drivers/usb/gadget/fusb300_udc.c:958: undefined reference to `usb_gadget_unmap_request'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since commit 511f3c53 (usb: gadget: udc-core: fix a regression during
gadget driver unbinding) usb_gadget_remove_driver will pass NULL for
the driver argument.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add the missing unlock before return from function cppi41_dma_callback()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Randy reported this
|drivers/usb/phy/phy-am335x-control.c:45:3: error: implicit declaration
|of function '__WARN' [-Werror=implicit-function-declaration]
and left it as an excercice to figure out that this happens only with
CONFIG_BUG=n. As a fix I replace it with WARN_ON(). And there is a space
before return so fix this, too.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since dma_map_single() may fail it is good to actually check the return
code to see if it succeeded.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If usb_add_function() fails then the currently processed function
is already not in the list in struct config_usb_cfg, and neither is it
in the list in struct usb_configuration. At the err_purge_funcs label the
purge_config_funcs() is called, which iterates over all configurations,
and in each configuration it iterates over all _successfully_ added
functions, and moves them back from the list in struct usb_configuration
to the list in struct config_usb_cfg. BUT the function which has just
failed adding and caused the unwind process is not taken care of and
is effectively lost.
This patch modifies the configfs_composite_bind() function so that if
the usb_add_function() fails, then the currently processed function
is returned to the list in struct config_usb_cfg.
It would be tempting to delay the list_del() in question after
usb_add_function() invocation, but a struct list_head (&f->list) cannot be
stored in more than one list at the same time, so the list_del() must
be called before usb_add_function(). Hence, the solution is to list_add()
after usb_add_function() in case of error.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When debug is not enabled and dev_dbg() will expand to nothing,
log might be flooded with "callbacks suppressed". If it was not
done on purpose, better to use dev_dbg_ratelimited() instead.
Signed-off-by: Dmitry Kasatkin <d.kasatkin@samsung.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Wrong capability bit was checked for best effort service latency.
bit 20 indicate port is BESL LPM capable (BLC),
bit 19 is hardware LPM capable (HLC)
This patch should be backported to kernels as old as 3.11, that
contain the commit a558ccdcc7 "usb: xhci:
add USB2 Link power management BESL support"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Steve Cotton <steve@s.cotton.clara.co.uk>
Cc: stable@vger.kernel.org
If a USB controller with XHCI_RESET_ON_RESUME goes to runtime suspend,
a reset will be performed upon runtime resume. Any previously suspended
devices attached to the controller will be re-enumerated at this time.
This will cause problems, for example, if an open system call on the
device triggered the resume (the open call will fail).
Note that this change is only relevant when persist_enabled is not set
for USB devices.
This patch should be backported to kernels as old as 3.0, that
contain the commit c877b3b2ad "xhci: Add
reset on resume quirk for asrock p67 host".
Signed-off-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Commit 9a11899c5e (USB: OHCI: add missing PCI PM callbacks to
ohci-pci.c) added missing ohci_suspend and ohci_resume callback
pointers, but forgot that these callbacks are declared and defined
only when CONFIG_PM is enabled.
This patch adds a preprocessor conditional to avoid build errors when
PM is disabled.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Meelis Roos <mroos@linux.ee>,
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up the DEVICE_ATTR usage in the USB serial drivers, making them
more obvious as to the permissions that the sysfs files should be.
Note: ftdi_sio.c still has a DEVICE_ATTR() used, that will have to wait
until after 3.12-rc1 comes out when DEVICE_ATTR_WO() shows up in Linus's
tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In auditing the usbtmc sysfs files, a bunch of them were being created
as "read only", yet they have logic to handle writing to. So fix them
up by setting the permissions properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of having to audit all sysfs attributes, to ensure we get them
right, use the default macros the driver core provides us (read-only,
read-write) to make the code simpler, and to prevent any mistakes from
ever happening.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drv_attrs field of struct bus_type is going away soon, drv_groups
should be used instead. This converts the USB serial bus code to use
the correct field.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After successful initialization hub->descriptor->bNbrPorts and
hub->hdev->maxchild are equal, but using hub->hdev->maxchild is
preferred because that value is explicitly used for initialization
of hub->ports[].
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ignoring usb_hub_create_port_device() errors cause later NULL pointer
deference when uninitialized hub->ports[i] entries are dereferenced
after port memory allocation error.
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the hub_configure() fails after setting the hdev->maxchild
the hub->ports might be NULL or point to uninitialized kzallocated
memory causing NULL pointer dereference in hub_quiesce() during cleanup.
Now after such error the hdev->maxchild is set to 0 to avoid cleanup
of uninitialized ports.
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7e8d5cd93f ("USB: Add EHCI support for MX27 and MX31 based
boards") introduced code that could potentially lead to a NULL pointer
dereference on driver removal.
Fix this by checking for the value of pdata before dereferencing it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org> # 2.6.33+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 94ae9843 (usb: phy: rename all phy drivers to phy-$name-usb.c)
renamed drivers/usb/phy/otg_fsm.h to drivers/usb/phy/phy-fsm-usb.h
but changed drivers/usb/phy/phy-fsm-usb.c to include not existing
"phy-otg-fsm.h" instead of new "phy-fsm-usb.h". This breaks building:
...
drivers/usb/phy/phy-fsm-usb.c:32:25: fatal error: phy-otg-fsm.h: No such file or directory
compilation terminated.
make[3]: *** [drivers/usb/phy/phy-fsm-usb.o] Error 1
This commit also missed to modify drivers/usb/phy/phy-fsl-usb.h
to include new "phy-fsm-usb.h" instead of "otg_fsm.h" resulting
in another build breakage:
...
In file included from drivers/usb/phy/phy-fsl-usb.c:46:0:
drivers/usb/phy/phy-fsl-usb.h:18:21: fatal error: otg_fsm.h: No such file or directory
compilation terminated.
make[3]: *** [drivers/usb/phy/phy-fsl-usb.o] Error 1
Fix both issues.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: stable <stable@vger.kernel.org> # 3.10+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c1117afb85 (USB: OHCI: make ohci-pci a separate driver)
neglected to preserve the entries for the pci_suspend and pci_resume
driver callbacks. As a result, OHCI controllers don't work properly
during suspend and after hibernation.
This patch adds the missing callbacks to the driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Steve Cotton <steve@s.cotton.clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use devm_get_clk() for automatic put upon device release, check for and
propagate errors when enabling clocks, must prepare clocks before they
can get enabled, unprepare after disable
need to use the _parent_ of the platform device for clock lookup, since
this one is associated with the respective device tree node; this change
remains neutral as long as a "globally" provided "usb%d_clk" item gets
provided by either the PPC_CLOCK implementation or clkdev_register'ed
aliases, using the correct devide and thus referencing the right DT node
becomes essential when clock lookup will become based on device tree
when common clock support will get introduced
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix endianess bugs in parallel-port code which caused corrupt
control-requests to be issued on big-endian machines.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write_parport_reg_nonblock() function shouldn't sleep because it's
called with spinlocks held.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The documentation for the USB gadget fs is actually in
Documentation/usb/gadget_configfs.txt.
Signed-off-by: Philippe De Swert <philippe.deswert@jollamobile.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
This is the first of two steps to fix your usb-linus and usb-next trees.
As I mentioned, commit 4fae6f0fa8 "USB:
handle LPM errors during device suspend correctly" was incorrectly added
to usb-next when it should have been added to usb-linus and marked for
stable.
Two port power off bug fixes touch the same code that patch touches, but
it's not easy to simply move commit 4fae6f0f patch to usb-linus because
commit 28e861658e "USB: refactor code for
enabling/disabling remote wakeup" also touched those code sections.
I propose a two step process to fix this:
1. Pull these four patches into usb-linus.
2. Revert commit 28e861658e from usb-next.
Merge usb-linus into usb-next, and resolve the conflicts.
I will be sending pull requests for these steps.
This pull request is step two.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=qfOL
-----END PGP SIGNATURE-----
Merge tag 'for-usb-2013-08-15-step-2' of ra.kernel.org:/pub/scm/linux/kernel/git/sarah/xhci into work-next
Sarah writes:
xhci: Step 2 to fix usb-linus and usb-next.
Hi Greg,
This is the first of two steps to fix your usb-linus and usb-next trees.
As I mentioned, commit 4fae6f0fa8 "USB:
handle LPM errors during device suspend correctly" was incorrectly added
to usb-next when it should have been added to usb-linus and marked for
stable.
Two port power off bug fixes touch the same code that patch touches, but
it's not easy to simply move commit 4fae6f0f patch to usb-linus because
commit 28e861658e "USB: refactor code for
enabling/disabling remote wakeup" also touched those code sections.
I propose a two step process to fix this:
1. Pull these four patches into usb-linus.
2. Revert commit 28e861658e from usb-next.
Merge usb-linus into usb-next, and resolve the conflicts.
I will be sending pull requests for these steps.
This pull request is step two.
Sarah Sharp
usb-serial-simple uses an unknown stringify macro that make
all drivers being named "stringify(vendor)".
This can be a problem when two drivers have the same (wrong) name:
kernel: usbcore: registered new interface driver usb_serial_simple
kernel: usbserial: USB Serial support registered for stringify(vendor)
kernel Error: Driver 'stringify(vendor)' is already registered, aborting...
kernel: usbserial: problem -16 when registering driver stringify(vendor)
kernel: usbserial: USB Serial deregistering driver stringify(vendor)
kernel: usbcore: deregistering interface driver usb_serial_simple
Before the fix:
$ strings drivers/usb/serial/usb-serial-simple.o
usb_serial_simple
stringify(vendor)
After the fix:
$ strings drivers/usb/serial/usb-serial-simple.o
usb_serial_simple
funsoft
flashloader
vivopay
moto_modem
hp4x
suunto
siemens_mpi
This patch makes usb-serial-simple use the correct stringify operator.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
This is the first of three steps to fix your usb-linus and usb-next
trees. As I mentioned, commit 4fae6f0fa8
"USB: handle LPM errors during device suspend correctly" was incorrectly
added to usb-next when it should have been added to usb-linus and marked
for stable.
Two port power off bug fixes touch the same code that patch touches, but
it's not easy to simply move commit 4fae6f0f patch to usb-linus because
commit 28e861658e "USB: refactor code for
enabling/disabling remote wakeup" also touched those code sections.
I propose a two step process to fix this:
1. Pull these four patches into usb-linus.
2. Revert commit 28e861658e from usb-next.
Merge usb-linus into usb-next, and resolve the conflicts.
I will be sending pull requests for these steps.
This pull request is step one, and contains the backported version of
commit 4fae6f0fa8, the two port power off
fixes, and an unrelated xhci-plat bug fix.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0/wL
-----END PGP SIGNATURE-----
Merge tag 'for-usb-2013-08-15-step-1' into for-usb-next
xhci: Step 1 to fix usb-linus and usb-next.
Hi Greg,
This is the first of three steps to fix your usb-linus and usb-next
trees. As I mentioned, commit 4fae6f0fa8
"USB: handle LPM errors during device suspend correctly" was incorrectly
added to usb-next when it should have been added to usb-linus and marked
for stable.
Two port power off bug fixes touch the same code that patch touches, but
it's not easy to simply move commit 4fae6f0f patch to usb-linus because
commit 28e861658e "USB: refactor code for
enabling/disabling remote wakeup" also touched those code sections.
I propose a two step process to fix this:
1. Pull these four patches into usb-linus.
2. Revert commit 28e861658e from usb-next.
Merge usb-linus into usb-next, and resolve the conflicts.
I will be sending pull requests for these steps.
This pull request is step one, and contains the backported version of
commit 4fae6f0fa8, the two port power off
fixes, and an unrelated xhci-plat bug fix.
Sarah Sharp
Resolved conflicts:
drivers/usb/core/hub.c
In wa_seg_init, use usb_init_urb to init the URB object contained in the
transfer segment instead of initializing it manually. Use kmalloc to
allocate the memory for segment instead of kzalloc and then use memset
to set the non-URB portion of the transfer segment struct to 0 since
that was already done by usb_init_urb.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check to free the URB was the opposite of the correct case. This
patch removes the check altogether since the ptr will be NULL if the URB
was not allocated. Also use usb_free_urb instead of usb_put_urb.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use usb_free_urb instead of kfree in error path and point to the correct
URB. Also remember to clean up the sg list for the URB if it was allocated.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bin Liu
Xenia Ragiadakou
Florian Wolter
Sarah Sharp
Mathias Nyman
Johan Hovold
Greg Kroah-Hartman
Frank Schäfer
Dave Jones
Chanho Park
Marek Szyprowski
Peter Oh
Sachin Kamat
David Cohen
Heikki Krogerus
Chen Gang
Andrzej Pietrasiewicz
Alan Stern
Alexey Khoroshilov
Linus Torvalds
Martin Schwidefsky
Libo Chen
Graham Williams
Lee Jones
Dan Carpenter
Anatolij Gustschin
Sebastian Andrzej Siewior
Julia Lawall
Geert Uytterhoeven
Maarten ter Huurne
Wei Yongjun
Dmitry Kasatkin
Shawn Nematbakhsh
Krzysztof Mazur
Daniel Mack
Gerhard Sittig
Philippe De Swert
Yann Droneaud
Thomas Pugliese