When sending "SLEEP" command to the controller it ceases scanning
completely and is unable to wake the system up from sleep, so if it is
configured as a wakeup source we should simply configure interrupt for
wakeup and rely on idle logic within the controller to reduce power
consumption while it is not used.
Signed-off-by: James Chen <james.chen@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Atmel maxtouch DT binding documents that the compatible string for
the device is "atmel,maxtouch" and the I2C core always reports a module
alias of the form i2c:alias where alias is the compatible string model:
$ grep MODALIAS /sys/devices/platform/12e00000.i2c/i2c-8/8-004b/uevent
MODALIAS=i2c:maxtouch
But there isn't maxtouch entry in the I2C device ID table so when the
i2c:maxtouch MODALIAS uevent is reported, kmod is not able to match the
alias with a module to load:
$ modinfo atmel_mxt_ts | grep alias
alias: of:N*T*Catmel,maxtouch
alias: i2c:mXT224
alias: i2c:atmel_mxt_tp
alias: i2c:atmel_mxt_ts
alias: i2c:qt602240_ts
So add the maxtouch entry to the I2C device ID table to allow the module
to be autoloaded when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Apparently people are installing generic Linux distributions not only on
Pixels but also on other Chromebooks. Unfortunately on all of them Atmel
parts assigned names ATML0000 and ATML0001, and do not carry any other
configuration data. So let's create generic instance of platform data that
should cover most of them (we assume that they will not be using T100
objects, since with those Google mapped BTN_LEFT onto a different GPIO, so
slightly different keymap would be needed, but I think we used parts with
T100 on ARM devices where we thankfully have DTS and can describe the
devices better).
Tested-by: Rich K <rgkirch@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull more input updates from Dmitry Torokhov:
"An update to the tsc2005 driver that allows it to also support tsc2004
(basically the same controller, but uses i2c instead of spi bus), and
a couple of bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: parkbd - drop bogus __init from parkbd_allocate_serio()
Input: elantech - add Fujitsu Lifebook U745 to force crc_enabled
Input: tsc2004 - add support for tsc2004
Input: tsc200x-core - rename functions and variables
Input: tsc2005 - separate SPI and core functions
Pull input updates from Dmitry Torokhov:
"Items of note:
- evdev users can now limit or mask the kind of events they will
receive. This will allow applications such as power manager or
network manager to only be woken when user presses special keys
such as KEY_POWER or KEY_WIFI and not be bothered with ordinary
key presses coming from keyboard
- support for FocalTech FT6236 touchscreen controller
- support for ROHM BU21023/24 touchscreen controller
- edt-ft5x06 touchscreen driver got a face lift and can now be used
with FT5506
- support for Google Fiber TV Box remote controls
- improvements in xpad driver (with more to come)
- several parport-based drivers have been switched to the new device
model
- other miscellaneous driver improvements"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (70 commits)
HID: hid-gfrm: avoid warning for input_configured API change
HID: hid-input: allow input_configured callback return errors
Input: evdev - fix bug in checking duplicate clock change request
Input: add userio module
Input: evdev - add event-mask API
Input: snvs_pwrkey - remove duplicated semicolon
HID: hid-gfrm: Google Fiber TV Box remote controls
Input: e3x0-button - update Kconfig description
Input: tegra-kbc - drop use of IRQF_NO_SUSPEND flag
Input: tegra-kbc - enable support for the standard "wakeup-source" property
Input: xen - check return value of xenbus_printf
Input: hp_sdc_rtc - fix y2038 problem in proc_show
Input: nomadik-ske-keypad - fix a trivial typo
Input: xpad - fix clash of presence handling with LED setting
Input: edt-ft5x06 - work around FT5506 firmware bug
Input: edt-ft5x06 - add support for FT5506
Input: edt-ft5x06 - add support for different max support points
Input: edt-ft5x06 - use max support points to determine how much to read
Input: rotary-encoder - add support for quarter-period mode
Input: rotary-encoder - use of_property_read_bool
...
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sR0p
-----END PGP SIGNATURE-----
Merge tag 'media/v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Media updates, including:
- Lots of improvements at the kABI documentation
- Split of Videobuf2 into a common part and a V4L2 specific one
- Split of the VB2 tracing events into a separate header file
- s5p-mfc got support for Exynos 5433
- v4l2 fixes for 64-bits alignment when running 32 bits userspace
on ARM
- Added support for SDR radio transmitter at core, vivid and hackrf
drivers
- Some y2038 fixups
- Some improvements at V4L2 colorspace support
- saa7164 converted to use the V4L2 core control framework
- several new boards additions, cleanups and fixups
PS: There are two patches for scripts/kernel-doc that are needed by
the documentation patches on Media. Jon is OK on merging those via
my tree"
* tag 'media/v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (146 commits)
[media] c8sectpfe: Remove select on CONFIG_FW_LOADER_USER_HELPER_FALLBACK
[media] DocBook media: update copyright/version numbers
[media] ivtv: Convert to get_user_pages_unlocked()
[media] media/v4l2-ctrls: fix setting autocluster to manual with VIDIOC_S_CTRL
[media] DocBook media: Fix a typo in encoder cmd
[media] DocBook: add SDR specific info to G_MODULATOR / S_MODULATOR
[media] DocBook: add SDR specific info to G_TUNER / S_TUNER
[media] hackrf: do not set human readable name for formats
[media] hackrf: add support for transmitter
[media] hackrf: switch to single function which configures everything
[media] hackrf: add control for RF amplifier
[media] DocBook: add modulator type field
[media] v4l: add type field to v4l2_modulator struct
[media] DocBook: document SDR transmitter
[media] v4l2: add support for SDR transmitter
[media] DocBook: document tuner RF gain control
[media] v4l2: add RF gain control
[media] v4l2: rename V4L2_TUNER_ADC to V4L2_TUNER_SDR
[media] media/vivid-osd: fix info leak in ioctl
[media] media: videobuf2: Move v4l2-specific stuff to videobuf2-v4l2
...
This adds support for the i2c based tsc2004 touchscreen controller.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The functions, variables, and defines of the new tsc200x-core.c are
renamed to tsc200x instead of tsc2005 avoid possible confusion.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch separates the SPI functionality from core functionality
that overlaps with the tsc2004.
Prepares kernel for new tsc2004 driver without much redundant code.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer fixes from Dmitry Torokhov:
- a change to the ALPS driver where we had limit the quirk for
trackstick handling from being active on all Dells to just a few
models
- a fix for a build dependency issue in the sur40 driver
- a small clock handling fixup in the LPC32xx touchscreen driver
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: alps - only the Dell Latitude D420/430/620/630 have separate stick button bits
Input: sur40 - add dependency on VIDEO_V4L2
Input: lpc32xx_ts - fix warnings caused by enabling unprepared clock
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace struct v4l2_format * with void * to make queue_setup()
for common use.
And then, modify all device drivers related with this change.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix missing const in fimc-lite.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix build errors due to missing Kconfig dependency.
drivers/built-in.o: In function `sur40_disconnect':
sur40.c:(.text+0x22be6e): undefined reference to `video_unregister_device'
sur40.c:(.text+0x22be77): undefined reference to `v4l2_device_unregister'
drivers/built-in.o: In function `sur40_process_video':
sur40.c:(.text+0x22c1d4): undefined reference to `v4l2_get_timestamp'
drivers/built-in.o: In function `sur40_probe':
sur40.c:(.text+0x22ca82): undefined reference to `v4l2_device_register'
sur40.c:(.text+0x22cb1a): undefined reference to `v4l2_device_unregister'
sur40.c:(.text+0x22cbf7): undefined reference to `video_device_release_empty'
sur40.c:(.text+0x22cc53): undefined reference to `__video_register_device'
sur40.c:(.text+0x22cc90): undefined reference to `video_unregister_device'
drivers/built-in.o: In function `sur40_vidioc_querycap':
sur40.c:(.text+0x22ccb0): undefined reference to `video_devdata'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If common clock framework is configured, the driver generates a warning,
which is fixed by this change:
root@devkit3250:~# cat /dev/input/touchscreen0
------------[ cut here ]------------
WARNING: CPU: 0 PID: 720 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
Modules linked in: sc16is7xx snd_soc_uda1380
CPU: 0 PID: 720 Comm: cat Not tainted 4.3.0-rc2+ #199
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (lpc32xx_setup_tsc+0x18/0xa0)
[<>] (lpc32xx_setup_tsc) from [<>] (lpc32xx_ts_open+0x14/0x1c)
[<>] (lpc32xx_ts_open) from [<>] (input_open_device+0x74/0xb0)
[<>] (input_open_device) from [<>] (evdev_open+0x110/0x16c)
[<>] (evdev_open) from [<>] (chrdev_open+0x1b4/0x1dc)
[<>] (chrdev_open) from [<>] (do_dentry_open+0x1dc/0x2f4)
[<>] (do_dentry_open) from [<>] (vfs_open+0x6c/0x70)
[<>] (vfs_open) from [<>] (path_openat+0xb4c/0xddc)
[<>] (path_openat) from [<>] (do_filp_open+0x40/0x8c)
[<>] (do_filp_open) from [<>] (do_sys_open+0x124/0x1c4)
[<>] (do_sys_open) from [<>] (SyS_open+0x2c/0x30)
[<>] (SyS_open) from [<>] (ret_fast_syscall+0x0/0x38)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"Just two small fixups to ads7846 touchscreen controller driver and
Cypress touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cyapa - fix the copy paste error on electrodes_rx value
Input: ads7846 - correct the value got from SPI
In the touchscreen controller ISR, reading the tsc starting from
register 0x2 causes the tsc to infrequently update the detected
finger's x and y coordinate. The irq pin toggles at a fast rate to
indicate touch events are happening. However, the tsc on average
updates the touch point's x and y value every ~100 ms which is much
slower than the advertised rate of 100+ Hz. This leads to multiple reads
within this ~100 ms time window returning the same value.
Example:
X: 10 , Y: 30
X: 10 , Y: 30
X: 10, Y: 30
..
// After 100 ms
X: 300, Y: 300
X: 300, y: 300
..
// After 100 ms
X: 1743, Y: 621
X: 1743, Y: 621
For some reason if instead of starting to read at register 0x2 you
start reading at register 0x0 this issue isn't seen. This seems like
a quirk only seen in the EDT FT5506 so to fix this issue simply
adjust the code to start reading from 0x0. Technically this isn't wrong
so no regressions should be seen with other touchscreen controllers
supported by this driver.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
FT5506 is essentially the same as other FT5x06 devices other than
supporting 10 support points.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Update the code so that the maximum supported points aren't hard coded but
can be changed.
Set the maximum support points based on the data passed along side the
compatible field.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Calculate the amount of data that needs to be read for the specified max
number of support points. If the maximum number of support points changes
then the amount that is read from the touch screen controller should
reflect this.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With commit 3fffd12839 ("i2c: allow specifying separate wakeup
interrupt in device tree") wakeirq is managed by i2c-core, so remove
wakeirq related code from pixcir_i2c_ts driver.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The copyright/license notice says that the code is licensed under GPL v2
only (not GPL v2+), so let's use proper string in MODULE_LICENSE().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to the touch controller spec, SPI return a 16 bit value, only 12
bits are valid, they are bit[14-3].
The value of MISO and MOSI can be configured when SPI is in idle mode.
Currently this touch driver assumes the SPI bus sets the MOSI and MISO in
low level when SPI bus is in idle mode. So the bit[15] of the value got
from SPI bus is always 0. But when SPI bus congfigures the MOSI and MISO in
high level during the SPI idle mode, the bit[15] of the value get from SPI
is always 1. If bit[15] is not masked, we may get the wrong value.
Mask the invalid bit to make sure the correct value gets returned.
Regardless of the SPI bus idle configuration.
Signed-off-by: Andrey Gelman <andrey.gelman@compulab.co.il>
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no need to explicitly set .owner for the driver, the core will do
it for us.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since reset and wake pin are optional the gpio structure for those
pins may be null. Therefore, they can't be blindly passed to
desc_to_gpio.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWEUxnAAoJEHm+PkMAQRiGYCYH/3gtGkFdvSLi+E1PfI8Qk3ZA
XuYA4Mj09JBVSmaICeueMTDVrdiq0OE0zPib26GWlF/za13kNU8KgMR3+6XCuLSX
DiCmh6mwDItoNoSIIUERLqrFHABXz8rZ3gb3uu2+kNN74Cl0piNm1YpFclEEWjMr
9Wk5fkq+ontnDVUQOvWUxPiUXOJTvdLXBWTRDw1yTdE3RMNwRI2d/hme6Hq++WYV
tRalZZKQaoB33js9WRVAoLVunvtna+i+/y7VGLj8QyS0+d6ec81Hey2r1/fR/oG4
bs4ul6vtqeb3IR/PjUqxF59pSrCLEO+qrp9KrTlJNYgr1m1QyjRxWUdy/XhyaWo=
=gIhN
-----END PGP SIGNATURE-----
Merge tag 'v4.3-rc4' into next
Merge with mainline to sync up with changes to parkbd driver.
Pull input layer fixes from Dmitry Torokhov:
"Fixes for two recent regressions (in Synaptics PS/2 and uinput
drivers) and some more driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - fix handling of disabling gesture mode"
Input: psmouse - fix data race in __ps2_command
Input: elan_i2c - add all valid ic type for i2c/smbus
Input: zhenhua - ensure we have BITREVERSE
Input: omap4-keypad - fix memory leak
Input: serio - fix blocking of parport
Input: uinput - fix crash when using ABS events
Input: elan_i2c - expand maximum product_id form 0xFF to 0xFFFF
Input: elan_i2c - add ic type 0x03
Input: elan_i2c - don't require known iap version
Input: imx6ul_tsc - fix controller name
Input: imx6ul_tsc - use the preferred method for kzalloc()
Input: imx6ul_tsc - check for negative return value
Input: imx6ul_tsc - propagate the errors
Input: walkera0701 - fix abs() calculations on 64 bit values
Input: mms114 - remove unneded semicolons
Input: pm8941-pwrkey - remove unneded semicolon
Input: fix typo in MT documentation
Input: cyapa - fix address of Gen3 devices in device tree documentation
This adds support for the FT6x06 and the FT6x36 family of capacitive touch
panel controllers, in particular the FT6236.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The PTR_ERR_OR_ZERO() helper function checks if a pointer contains an
errno code and returns it or return 0 if that's not the case. Use the
helper instead of open coding the same logic in the driver. This was
found with make coccicheck that complains with the following warning:
drivers/input/touchscreen/cyttsp4_i2c.c:53:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The PTR_ERR_OR_ZERO() helper function checks if a pointer contains an
errno code and returns it or return 0 if that's not the case. Use the
helper instead of open coding the same logic in the driver. This was
found with make coccicheck that complains with the following warning:
drivers/input/touchscreen/ads7846.c:532:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The invoked function already returns zero on success or a negative
errno code so there is no need to open code the logic in the caller.
This also fixes the following make coccicheck warning:
drivers/input/touchscreen/tps6507x-ts.c:57:5-8: WARNING: end returns can be simplified
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The invoked function already returns zero on success or a negative
errno code so there is no need to open code the logic in the caller.
This also fixes the following make coccicheck warnings:
end returns can be simplified and declaration on line 402 can be dropped
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The invoked function already returns zero on success or a negative
errno code so there is no need to open code the logic in the caller.
This also fixes the following make coccicheck warning:
end returns can be simplified and declaration on line 602 can be dropped
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@bq.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove v4l2 stuff - v4l2_buf, v4l2_plane - from struct vb2_buffer.
Add new member variables - bytesused, length, offset, userptr, fd,
data_offset - to struct vb2_plane in order to cover all information
of v4l2_plane.
struct vb2_plane {
<snip>
unsigned int bytesused;
unsigned int length;
union {
unsigned int offset;
unsigned long userptr;
int fd;
} m;
unsigned int data_offset;
}
Replace v4l2_buf with new member variables - index, type, memory - which
are common fields for buffer management.
struct vb2_buffer {
<snip>
unsigned int index;
unsigned int type;
unsigned int memory;
unsigned int num_planes;
struct vb2_plane planes[VIDEO_MAX_PLANES];
<snip>
};
v4l2 specific fields - flags, field, timestamp, timecode,
sequence - are moved to vb2_v4l2_buffer in videobuf2-v4l2.c
struct vb2_v4l2_buffer {
struct vb2_buffer vb2_buf;
__u32 flags;
__u32 field;
struct timeval timestamp;
struct v4l2_timecode timecode;
__u32 sequence;
};
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWB9f6AAoJEHm+PkMAQRiGiFMIAJYFLIkF/dXFYMNPGsRGRGYO
SsQkfYzjy4i/yloyVlGB33e6dqxWdVgCeqYC77TO+1CBq34o6dqM4PACTrhjtS+3
qQvaP/qn6cSoaGIkdD3v43CCiwMpZZ5+Uj7F7Uz8N4twrpykOZFMM5T7f1lrsG2F
wJGafmvok9NU2F2wYwaJ8JrzsF6iO6ibFeB8BosRF5Ba4nKqiXVI0xNa0R8PFDm3
tbh/IkkqokemEqnHyWyszhGFsCQupi+QgsjY/LhWUcCaL7HLEgJmkBX0tXNlgMmK
TFCq7L8Bigu4nlgZ/iVUB9kh4GTBNVcbdRVN3loJFlczFJlIAa171OVlfRu3lvU=
=m29x
-----END PGP SIGNATURE-----
Merge tag 'v4.3-rc3' into next
Merge with Linux 4.3-rc3 to bring in MFD DA9062 changes to merge DA9062
OnKey driver.
Instead of hardcoding IRQ trigger type to IRQF_TRIGGER_FALLING, let's
respect settings specified in device tree. To be compatible with older
DTSes, if trigger type is not set up in DTS we'll set it to default
(falling edge).
Tested-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of only parsing device tree properties let's switch to using
generic properties API so that the driver can also work on other platforms.
Tested-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We do not have any users of platform data in the tree and all newer
platforms are either DT or ACPI, so let's drop handling of platform data.
Tested-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver does not use irq gpio as gpio, but rather relies on I2C core or
board code to set up client's structure IRQ line, so let's stop trying to
locate the resource and parse it.
Tested-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current/old gpio framework used doesn't properly listen to
ACTIVE_LOW and ACTIVE_HIGH flags. The newer gpio framework takes into
account these flags when setting gpio values.
Since the values being output were based on voltage and not logic they
change to reflect this difference. Also use gpiod_set_value_cansleep since
wake and reset pins can be provided by bus based io expanders.
Switch from msleep(5) to udelay_range(5000,6000) to avoid check patch
warning.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to Documentation/CodingStyle:
"The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);"
so do as suggested.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should check for negative values returned by platform_get_irq().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
imx6ul_adc_init() may fail in two cases, so we should better
propagate the errors and make sure that the callers of
this function also check and propagate the errors accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
They aren't needed and are just creating null statements so remove it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Linus Torvalds
James Chen
Javier Martinez Canillas
Dmitry Torokhov
Mark Brown
Michael Welling
Andrew F. Davis
Junghak Sung
Randy Dunlap
Vladimir Zapolskiy
Franklin S Cooper Jr
Vignesh R
Andrey Gelman
Fengguang Wu
Yoichi Yuasa
Noralf Trønnes
Fabio Estevam