This replaces direct accesses to TCE table with a helper which
returns an TCE entry address. This does not make difference now but will
when multi-level TCE tables get introduces.
No change in behavior is expected.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The iommu_table struct keeps a list of IOMMU groups it is used for.
At the moment there is just a single group attached but further
patches will add TCE table sharing. When sharing is enabled, TCE cache
in each PE needs to be invalidated so does the patch.
This does not change pnv_pci_ioda1_tce_invalidate() as there is no plan
to enable TCE table sharing on PHBs older than IODA2.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the moment the DMA setup code looks for the "ibm,opal-tce-kill"
property which contains the TCE kill register address. Writing to
this register invalidates TCE cache on IODA/IODA2 hub.
This moves the register address from iommu_table to pnv_pnb as this
register belongs to PHB and invalidates TCE cache for all tables of
all attached PEs.
This moves the property reading/remapping code to a helper which is
called when DMA is being configured for PE and which does DMA setup
for both IODA1 and IODA2.
This adds a new pnv_pci_ioda2_tce_invalidate_entire() helper which
invalidates cache for the entire table. It should be called after
every call to opal_pci_map_pe_dma_window(). It was not required before
because there was just a single TCE table and 64bit DMA was handled via
bypass window (which has no table so no cache was used) but this is going
to change with Dynamic DMA windows (DDW).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds missing locks in iommu_take_ownership()/
iommu_release_ownership().
This marks all pages busy in iommu_table::it_map in order to catch
errors if there is an attempt to use this table while ownership over it
is taken.
This only clears TCE content if there is no page marked busy in it_map.
Clearing must be done outside of the table locks as iommu_clear_tce()
called from iommu_clear_tces_and_put_pages() does this.
In order to use bitmap_empty(), the existing code clears bit#0 which
is set even in an empty table if it is bus-mapped at 0 as
iommu_init_table() reserves page#0 to prevent buggy drivers
from crashing when allocated page is bus-mapped at zero
(which is correct). This restores the bit in the case of failure
to bring the it_map to the state it was in when we called
iommu_take_ownership().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds tce_iommu_take_ownership() and tce_iommu_release_ownership
which call in a loop iommu_take_ownership()/iommu_release_ownership()
for every table on the group. As there is just one now, no change in
behaviour is expected.
At the moment the iommu_table struct has a set_bypass() which enables/
disables DMA bypass on IODA2 PHB. This is exposed to POWERPC IOMMU code
which calls this callback when external IOMMU users such as VFIO are
about to get over a PHB.
The set_bypass() callback is not really an iommu_table function but
IOMMU/PE function. This introduces a iommu_table_group_ops struct and
adds take_ownership()/release_ownership() callbacks to it which are
called when an external user takes/releases control over the IOMMU.
This replaces set_bypass() with ownership callbacks as it is not
necessarily just bypass enabling, it can be something else/more
so let's give it more generic name.
The callbacks is implemented for IODA2 only. Other platforms (P5IOC2,
IODA1) will use the old iommu_take_ownership/iommu_release_ownership API.
The following patches will replace iommu_take_ownership/
iommu_release_ownership calls in IODA2 with full IOMMU table release/
create.
As we here and touching bypass control, this removes
pnv_pci_ioda2_setup_bypass_pe() as it does not do much
more compared to pnv_pci_ioda2_set_bypass. This moves tce_bypass_base
initialization to pnv_pci_ioda2_setup_dma_pe.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
So far one TCE table could only be used by one IOMMU group. However
IODA2 hardware allows programming the same TCE table address to
multiple PE allowing sharing tables.
This replaces a single pointer to a group in a iommu_table struct
with a linked list of groups which provides the way of invalidating
TCE cache for every PE when an actual TCE table is updated. This adds
pnv_pci_link_table_and_group() and pnv_pci_unlink_table_and_group()
helpers to manage the list. However without VFIO, it is still going
to be a single IOMMU group per iommu_table.
This changes iommu_add_device() to add a device to a first group
from the group list of a table as it is only called from the platform
init code or PCI bus notifier and at these moments there is only
one group per table.
This does not change TCE invalidation code to loop through all
attached groups in order to simplify this patch and because
it is not really needed in most cases. IODA2 is fixed in a later
patch.
This should cause no behavioural change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Modern IBM POWERPC systems support multiple (currently two) TCE tables
per IOMMU group (a.k.a. PE). This adds a iommu_table_group container
for TCE tables. Right now just one table is supported.
This defines iommu_table_group struct which stores pointers to
iommu_group and iommu_table(s). This replaces iommu_table with
iommu_table_group where iommu_table was used to identify a group:
- iommu_register_group();
- iommudata of generic iommu_group;
This removes @data from iommu_table as it_table_group provides
same access to pnv_ioda_pe.
For IODA, instead of embedding iommu_table, the new iommu_table_group
keeps pointers to those. The iommu_table structs are allocated
dynamically.
For P5IOC2, both iommu_table_group and iommu_table are embedded into
PE struct. As there is no EEH and SRIOV support for P5IOC2,
iommu_free_table() should not be called on iommu_table struct pointers
so we can keep it embedded in pnv_phb::p5ioc2.
For pSeries, this replaces multiple calls of kzalloc_node() with a new
iommu_pseries_alloc_group() helper and stores the table group struct
pointer into the pci_dn struct. For release, a iommu_table_free_group()
helper is added.
This moves iommu_table struct allocation from SR-IOV code to
the generic DMA initialization code in pnv_pci_ioda_setup_dma_pe and
pnv_pci_ioda2_setup_dma_pe as this is where DMA is actually initialized.
This change is here because those lines had to be changed anyway.
This should cause no behavioural change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pnv_pci_ioda_tce_invalidate() helper invalidates TCE cache. It is
supposed to be called on IODA1/2 and not called on p5ioc2. It receives
start and end host addresses of TCE table.
IODA2 actually needs PCI addresses to invalidate the cache. Those
can be calculated from host addresses but since we are going
to implement multi-level TCE tables, calculating PCI address from
a host address might get either tricky or ugly as TCE table remains flat
on PCI bus but not in RAM.
This moves pnv_pci_ioda_tce_invalidate() from generic pnv_tce_build/
pnt_tce_free and defines IODA1/2-specific callbacks which call generic
ones and do PHB-model-specific TCE cache invalidation. P5IOC2 keeps
using generic callbacks as before.
This changes pnv_pci_ioda2_tce_invalidate() to receives TCE index and
number of pages which are PCI addresses shifted by IOMMU page shift.
No change in behaviour is expected.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a iommu_table_ops struct and puts pointer to it into
the iommu_table struct. This moves tce_build/tce_free/tce_get/tce_flush
callbacks from ppc_md to the new struct where they really belong to.
This adds the requirement for @it_ops to be initialized before calling
iommu_init_table() to make sure that we do not leave any IOMMU table
with iommu_table_ops uninitialized. This is not a parameter of
iommu_init_table() though as there will be cases when iommu_init_table()
will not be called on TCE tables, for example - VFIO.
This does s/tce_build/set/, s/tce_free/clear/ and removes "tce_"
redundant prefixes.
This removes tce_xxx_rm handlers from ppc_md but does not add
them to iommu_table_ops as this will be done later if we decide to
support TCE hypercalls in real mode. This removes _vm callbacks as
only virtual mode is supported by now so this also removes @rm parameter.
For pSeries, this always uses tce_buildmulti_pSeriesLP/
tce_buildmulti_pSeriesLP. This changes multi callback to fall back to
tce_build_pSeriesLP/tce_free_pSeriesLP if FW_FEATURE_MULTITCE is not
present. The reason for this is we still have to support "multitce=off"
boot parameter in disable_multitce() and we do not want to walk through
all IOMMU tables in the system and replace "multi" callbacks with single
ones.
For powernv, this defines _ops per PHB type which are P5IOC2/IODA1/IODA2.
This makes the callbacks for them public. Later patches will extend
callbacks for IODA1/2.
No change in behaviour is expected.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Normally a bitmap from the iommu_table is used to track what TCE entry
is in use. Since we are going to use iommu_table without its locks and
do xchg() instead, it becomes essential not to put bits which are not
implied in the direction flag as the old TCE value (more precisely -
the permission bits) will be used to decide whether to put the page or not.
This adds iommu_direction_to_tce_perm() (its counterpart is there already)
and uses it for powernv's pnv_tce_build().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves page pinning (get_user_pages_fast()/put_page()) code out of
the platform IOMMU code and puts it to VFIO IOMMU driver where it belongs
to as the platform code does not deal with page pinning.
This makes iommu_take_ownership()/iommu_release_ownership() deal with
the IOMMU table bitmap only.
This removes page unpinning from iommu_take_ownership() as the actual
TCE table might contain garbage and doing put_page() on it is undefined
behaviour.
Besides the last part, the rest of the patch is mechanical.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for the vfio related changes]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the moment iommu_free_table() only releases memory if
the table was initialized for the platform code use, i.e. it had
it_map initialized (which purpose is to track DMA memory space use).
With dynamic DMA windows, we will need to be able to release
iommu_table even if it was used for VFIO in which case it_map is NULL
so does the patch.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
So far an iommu_table lifetime was the same as PE. Dynamic DMA windows
will change this and iommu_free_table() will not always require
the group to be released.
This moves iommu_group_put() out of iommu_free_table().
This adds a iommu_pseries_free_table() helper which does
iommu_group_put() and iommu_free_table(). Later it will be
changed to receive a table_group and we will have to change less
lines then.
This should cause no behavioural change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The existing code has 3 calls to iommu_register_group() and
all 3 branches actually cover all possible cases.
This replaces 3 calls with one and moves the registration earlier;
the latter will make more sense when we add TCE table sharing.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The set_iommu_table_base_and_group() name suggests that the function
sets table base and add a device to an IOMMU group.
The actual purpose for table base setting is to put some reference
into a device so later iommu_add_device() can get the IOMMU group
reference and the device to the group.
At the moment a group cannot be explicitly passed to iommu_add_device()
as we want it to work from the bus notifier, we can fix it later and
remove confusing calls of set_iommu_table_base().
This replaces set_iommu_table_base_and_group() with a couple of
set_iommu_table_base() + iommu_add_device() which makes reading the code
easier.
This adds few comments why set_iommu_table_base() and iommu_add_device()
are called where they are called.
For IODA1/2, this essentially removes iommu_add_device() call from
the pnv_pci_ioda_dma_dev_setup() as it will always fail at this particular
place:
- for physical PE, the device is already attached by iommu_add_device()
in pnv_pci_ioda_setup_dma_pe();
- for virtual PE, the sysfs entries are not ready to create all symlinks
so actual adding is happening in tce_iommu_bus_notifier.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This relies on the fact that a PCI device always has an IOMMU table
which may not be the case when we get dynamic DMA windows so
let's use more reliable check for IOMMU group here.
As we do not rely on the table presence here, remove the workaround
from pnv_pci_ioda2_set_bypass(); also remove the @add_to_iommu_group
parameter from pnv_ioda_setup_bus_dma().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds some in-code documentation to the DSCR related code to
make it more readable without having any functional change to it.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PACA_DSCR offset macro tracks dscr_default element in the paca
structure. Better change the name of this macro to match that of the
data element it tracks. Makes the code more readable.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The process context switch code no longer uses dscr_default variable
from the sysfs.c file. The variable became unused when we started
storing the CPU specific DSCR value in the PACA structure instead.
This patch just removes this extern declaration. It was originally
added by the following commit.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently DSCR (Data Stream Control Register) can be accessed with
mfspr or mtspr instructions inside a thread via two different SPR
numbers. One being the user accessible problem state SPR number 0x03
and the other being the privilege state SPR number 0x11. All access
through the privilege state SPR number get emulated through illegal
instruction exception. Any access through the problem state SPR number
raises one facility unavailable exception which sets the thread based
dscr_inherit bit and enables DSCR facility through FSCR register thus
allowing direct access to DSCR without going through this exception in
the future. We set the thread.dscr_inherit bit whether the access was
with mfspr or mtspr instruction which is neither correct nor does it
match the behaviour through the instruction emulation code path driven
from privilege state SPR number. User currently observes two different
kind of behaviour when accessing the DSCR through these two SPR numbers.
This problem can be observed through these two test cases by replacing
the privilege state SPR number with the problem state SPR number.
(1) http://ozlabs.org/~anton/junkcode/dscr_default_test.c
(2) http://ozlabs.org/~anton/junkcode/dscr_explicit_test.c
This patch fixes the problem by making sure that the behaviour visible
to the user remains the same irrespective of which SPR number is being
used. Inside facility unavailable exception, we check whether it was
cuased by a mfspr or a mtspr isntrucction. In case of mfspr instruction,
just emulate the instruction. In case of mtspr instruction, set the
thread based dscr_inherit bit and also enable the facility through FSCR.
All user SPR based mfspr instruction will be emulated till one user SPR
based mtspr has been executed.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 28158cd "powerpc/eeh: Enhance pcibios_set_pcie_reset_state()"
introduced a fix for a problem where certain configurations could lead to
pci_reset_function() destroying the state of PCI devices other than the one
specified.
Unfortunately, the fix has a trivial bug - it calls pci_save_state() again,
when it should be calling pci_restore_state(). This corrects the problem.
Cc: Gavin Shan <gwshan@au1.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This change adds a char device to access the "PRD" (processor runtime
diagnostics) channel to OPAL firmware.
Includes contributions from Vaidyanathan Srinivasan, Neelesh Gupta &
Vishal Kulkarni.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The (upcoming) opal-prd driver needs to access the message notifier and
xscom code, so add EXPORT_SYMBOL_GPL macros for these.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
opal_ipmi_init and opal_flash_init are equivalent, except for the
compatbile string. Merge these two into a common opal_pdev_init
function.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The opal_{get,set}_param calls return internal error codes which need
to be translated in errnos in Linux.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This moves the current include file from cxl.h -> cxl-base.h. This current
include file is used only to pass information between the base driver that
needs to be built into the kernel and the cxl module.
This is to make way for a new include/misc/cxl.h which will
contain just the kernel API for other driver to use
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds a hook into the powerpc pci code for pci_disable_device() calls. The
generic code already provides a weak pcibios_disable_device() symbol, so we
just need to provide our own in powerpc and it'll get picked up.
This is passed directly to the phb controller ops, provided one exists.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently pnv_pci_shutdown() calls the PHB shutdown code for all PHBs in the
system. It dereferences the private_data assuming it's a powernv PHB, which
won't be the case when we have different PHB in the systems (like when we add
vPHBs for CXL).
This moves the shutdown hook to the pci_controller_ops and fixes the call site
to use that instead.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add cxl context pointer to archdata. We'll want to create one of these for cxl
PCI devices. Put them here until we can get a pci_dev specific private data.
This location was suggested by benh.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add release_device() hook to phb ops so we can clean up for specific phbs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Export pcibios_claim_one_bus, pcibios_scan_phb and pcibios_alloc_controller.
These will be used by the CXL driver.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes calculating the key bits (KP and KS) in the SLB VSID for kernel
mappings.
I'm not CCing this to stable as there are no uses of this currently.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rather than continuing to maintain a copy of pseries_defconfig with
CONFIG_CPU_LITTLE_ENDIAN enabled, use the generic merge_config script
and use an le.config to enable little endian on top of pseries_defconfig
without the need for a duplicated _defconfig file.
This method will require less maintenance in the future and will ensure
that both 'defconfigs' are always in sync.
It is worth noting that the seemingly more simple approach of:
pseries_le_defconfig: pseries_defconfig
$(Q)$(MAKE) le.config
Will not work when building using O=builddir.
The obvious fix to that:
pseries_le_defconfig:
$(Q)$(MAKE) -f $(srctree)/Makefile pseries_defconfig le.config
Also does not work. This is because if we have for example:
config FOO
depends on CPU_BIG_ENDIAN
select BAR
Then BAR will be enabled by the first call to kconfig (via
pseries_defconfig), and then will remain enabled after we merge
le.config, even though FOO will have been turned off.
The solution is to ensure to only invoke the kconfig logic once, after
we have merged all the config fragments. This ensures nothing is
select'ed on that should then be disabled by the later merged configs.
This is done through the explicit call to make olddefconfig
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Reviewed-by: Samuel Mendoza-Jonas <sam.mj@au1.ibm.com>
[mpe: Massage change log, fix white space and use ARCH not SRCARCH]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These two configs should be identical with the exception of big or little
endian.
The big endian version has XMON_DEFAULT turned on while the little endian
has XMON_DEFAULT not set. It makes the most sense for defconfigs not to use
xmon by default, production systems should get back up as quickly as
possible, not sit in xmon.
In the event debugging is required, the option can be enabled or xmon=on
can be specified on commandline.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we
already have a pointer to corresponding irq_desc.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We need to use a trampoline when using LOAD_HANDLER(), because the
destination needs to be in the first 64kB. An absolute branch has
no such limitations, so just jump there.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We had some code to restore the LR in the relocatable system call path
back when we used the LR to do an indirect branch.
Commit 6a404806df ("powerpc: Avoid link stack corruption in MMU
on syscall entry path") changed this to use the CTR which is volatile
across system calls so does not need restoring.
Remove the stale comment and the restore of the LR.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we take a PMU exception or a software event we call
perf_read_regs(). This overloads regs->result with a boolean that
describes if we should use the sampled instruction address register
(SIAR) or the regs.
If the exception is in kernel, we start with the kernel regs and
backtrace through the kernel stack. At this point we switch to the
userspace regs and backtrace the user stack with perf_callchain_user().
Unfortunately these regs have not got the perf_read_regs() treatment,
so regs->result could be anything. If it is non zero,
perf_instruction_pointer() decides to use the SIAR, and we get issues
like this:
0.11% qemu-system-ppc [kernel.kallsyms] [k] _raw_spin_lock_irqsave
|
---_raw_spin_lock_irqsave
|
|--52.35%-- 0
| |
| |--46.39%-- __hrtimer_start_range_ns
| | kvmppc_run_core
| | kvmppc_vcpu_run_hv
| | kvmppc_vcpu_run
| | kvm_arch_vcpu_ioctl_run
| | kvm_vcpu_ioctl
| | do_vfs_ioctl
| | sys_ioctl
| | system_call
| | |
| | |--67.08%-- _raw_spin_lock_irqsave <--- hi mum
| | | |
| | | --100.00%-- 0x7e714
| | | 0x7e714
Notice the bogus _raw_spin_irqsave when we transition from kernel
(system_call) to userspace (0x7e714). We inserted what was in the SIAR.
Add a check in regs_use_siar() to check that the regs in question
are from a PMU exception. With this fix the backtrace makes sense:
0.47% qemu-system-ppc [kernel.vmlinux] [k] _raw_spin_lock_irqsave
|
---_raw_spin_lock_irqsave
|
|--53.83%-- 0
| |
| |--44.73%-- hrtimer_try_to_cancel
| | kvmppc_start_thread
| | kvmppc_run_core
| | kvmppc_vcpu_run_hv
| | kvmppc_vcpu_run
| | kvm_arch_vcpu_ioctl_run
| | kvm_vcpu_ioctl
| | do_vfs_ioctl
| | sys_ioctl
| | system_call
| | __ioctl
| | 0x7e714
| | 0x7e714
Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If both STRICT_MM_TYPECHECKS and DEBUG_PAGEALLOC are enabled, the code
in kernel_map_linear_page() is built, and so we fail with:
arch/powerpc/mm/hash_utils_64.c:1478:2:
error: incompatible type for argument 1 of 'htab_convert_pte_flags'
Fix it by using pgprot_val().
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Previously, dma_set_mask() on powernv was convoluted:
0) Call dma_set_mask() (a/p/kernel/dma.c)
1) In dma_set_mask(), ppc_md.dma_set_mask() exists, so call it.
2) On powernv, that function pointer is pnv_dma_set_mask().
In pnv_dma_set_mask(), the device is pci, so call pnv_pci_dma_set_mask().
3) In pnv_pci_dma_set_mask(), call pnv_phb->set_dma_mask() if it exists.
4) It only exists in the ioda case, where it points to
pnv_pci_ioda_dma_set_mask(), which is the final function.
So the call chain is:
dma_set_mask() ->
pnv_dma_set_mask() ->
pnv_pci_dma_set_mask() ->
pnv_pci_ioda_dma_set_mask()
Both ppc_md and pnv_phb function pointers are used.
Rip out the ppc_md call, pnv_dma_set_mask() and pnv_pci_dma_set_mask().
Instead:
0) Call dma_set_mask() (a/p/kernel/dma.c)
1) In dma_set_mask(), the device is pci, and pci_controller_ops.dma_set_mask()
exists, so call pci_controller_ops.dma_set_mask()
2) In the ioda case, that points to pnv_pci_ioda_dma_set_mask().
The new call chain is
dma_set_mask() ->
pnv_pci_ioda_dma_set_mask()
Now only the pci_controller_ops function pointer is used.
The fallback paths for p5ioc2 are the same.
Previously, pnv_pci_dma_set_mask() would find no pnv_phb->set_dma_mask()
function, to it would call __set_dma_mask().
Now, dma_set_mask() finds no ppc_md call or pci_controller_ops call,
so it calls __set_dma_mask().
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some systems only need to deal with DMA masks for PCI devices.
For these systems, we can avoid the need for a platform hook and
instead use a pci controller based hook.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove powernv generic PCI controller operations. Replace it with
controller ops for each of the two supported PHBs.
As an added bonus, make the two new structs const, which will help
guard against bugs such as the one introduced in 65ebf4b63
("powerpc/powernv: Move controller ops from ppc_md to controller_ops")
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove unneeded ppc_md functions. Patch callsites to use pci_controller_ops
functions exclusively.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the u3 MPIC msi subsystem to use the pci_controller_ops structure
rather than ppc_md for MSI related PCI controller operations.
As with fsl_msi, operations are plugged in at the subsys level, after
controller creation. Again, we iterate over all controllers and
populate them with the MSI ops.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the PaSemi MPIC msi subsystem to use the pci_controller_ops
structure rather than ppc_md for MSI related PCI controller
operations.
As with fsl_msi, operations are plugged in at the subsys level, after
controller creation. Again, we iterate over all controllers and
populate them with the MSI ops.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the ppc4xx hsta msi subsystem to use the pci_controller_ops
structure rather than ppc_md for MSI related PCI controller
operations.
As with fsl_msi, operations are plugged in at the subsys level, after
controller creation. Again, we iterate over all controllers and
populate them with the MSI ops.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the ppc4xx msi subsystem to use the pci_controller_ops structure
rather than ppc_md for MSI related PCI controller operations.
As with fsl_msi, operations are plugged in at the subsys level, after
controller creation. Again, we iterate over all controllers and
populate them with the MSI ops.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the fsl_msi subsystem to use the pci_controller_ops structure
rather than ppc_md for MSI related PCI controller operations.
Previously, MSI ops were added to ppc_md at the subsys level. However,
in fsl_pci.c, PCI controllers are created at the at arch level. So,
unlike in e.g. PowerNV/pSeries/Cell, we can't simply populate a
platform-level controller ops structure and have it copied into the
controllers when they are created.
Instead, walk every phb, and attempt to populate it with the MSI ops.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Alexey Kardashevskiy
Aneesh Kumar K.V
Anshuman Khandual
David Gibson
Jeremy Kerr
Anton Blanchard
Cédric Le Goater
Michael Neuling
Daniel Axtens
Cyril Bur
Jiang Liu
Michael Ellerman