Tulip throws an error when dma debugging is enabled, as it doesn't properly
check dma mapping results with dma_mapping_error() durring tx ring refills.
Easy fix, just add it in, and drop the frame if the mapping is bad
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Grant Grundler <grundler@parisc-linux.org>
CC: "David S. Miller" <davem@davemloft.net>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue that the driver increments the "RX length error"
on every buffer in sh_eth_rx() if the R8A7740.
This patch also adds a description about the Receive Frame Status bits.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During suspend resume cycle all the register data is lost, so MDIO
clock divier value gets reset. This patch restores the clock divider
value.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO driver should resume before CPSW ethernet driver so that CPSW connect
to the phy and start tx/rx ethernet packets, changing the suspend/resume
apis with suspend_late/resume_early.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some systems that don't need wake-on-lan may choose to power down the
chip on system standby. Upon resume, the power on causes the boot code
to startup and initialize the hardware. On one new platform, this is
causing the device to go into a bad state due to a race between the
driver and boot code, once every several hundred resumes. The same race
exists on open since we come up from a power on.
This patch adds a wait for boot code signature at the beginning of
tg3_init_hw() which is common to both cases. If there has not been a
power-off or the boot code has already completed, the signature will be
present and poll_fw() returns immediately. Also return immediately if
the device does not have firmware.
Cc: stable@vger.kernel.org
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First the type of igmp_retrans (which is the actual counter of
igmp_resend parameter) is changed to u8 to be able to store values up
to 255 (as per documentation). There are two races that were hidden
there and which are easy to trigger after the previous fix, the first is
between bond_resend_igmp_join_requests and bond_change_active_slave
where igmp_retrans is set and can be altered by the periodic. The second
race condition is between multiple running instances of the periodic
(upon execution it can be scheduled again for immediate execution which
can cause the counter to go < 0 which in the unsigned case leads to
unnecessary igmp retransmissions).
Since in bond_change_active_slave bond->lock is held for reading and
curr_slave_lock for writing, we use curr_slave_lock for mutual
exclusion. We can't drop them as there're cases where RTNL is not held
when bond_change_active_slave is called. RCU is unlocked in
bond_resend_igmp_join_requests before getting curr_slave_lock since we
don't need it there and it's pointless to delay.
The decrement is moved inside the "if" block because if we decrement
unconditionally there's still a possibility for a race condition although
it is much more difficult to hit (many changes have to happen in
a very short period in order to trigger) which in the case of 3 parallel
running instances of this function and igmp_retrans == 1
(with check bond->igmp_retrans-- > 1) is:
f1 passes, doesn't re-schedule, but decrements - igmp_retrans = 0
f2 then passes, doesn't re-schedule, but decrements - igmp_retrans = 255
f3 does the unnecessary retransmissions.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the bond device is supposed to get the first slave's MAC address and
the first enslavement fails then we need to reset the master's MAC
otherwise it will stay the same as the failed slave device. We do it
after err_undo_flags since that is the first place where the MAC can be
changed and we check if it should've been the first slave and if the
bond's MAC was set to it because that err place is used by multiple
locations prior to changing the master's MAC address.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c: In function:
stmmac_xmit drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1902:74:
error: expected ) before __func__
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to set the coherent DMA mask only if dma_set_mask() succeeded, and to
error out if either fails.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When putting vif-s on the rx notify list, calling xenvif_put() must be
deferred until after the removal from the list and the issuing of the
notification, as both operations dereference the pointer.
Changing this got me to notice that the "irq" variable was effectively
unused (and was of too narrow type anyway).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit df8ef8f3aa
"macvlan: add FDB bridge ops and macvlan flags"
added a way to control NOPROMISC macvlan flag through netlink.
However, with a non passthrough device we never set promisc on open,
even if NOPROMISC is off. As a result:
If userspace clears NOPROMISC on open, then does not clear it on a
netlink command, promisc counter is not decremented on stop and there
will be no way to clear it once macvlan is detached.
If userspace does not clear NOPROMISC on open, then sets NOPROMISC on a
netlink command, promisc counter will be decremented from 0 and overflow
to fffffffff with no way to clear promisc.
To fix, simply ignore NOPROMISC flag in a netlink command for
non-passthrough devices, same as we do at open/close.
Since we touch this code anyway - check dev_set_promiscuity return code
and pass it to users (though an error here is unlikely).
Cc: "David S. Miller" <davem@davemloft.net>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The module parameter "fwpostfix" is userspace controllable, unfiltered,
and is used to define the firmware filename. b43_do_request_fw() populates
ctx->errors[] on error, containing the firmware filename. b43err()
parses its arguments as a format string. For systems with b43 hardware,
this could lead to a uid-0 to ring-0 escalation.
CVE-2013-2852
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k rate control algorithm has various architectural
issues that make it a poor fit in scenarios like congested
environments etc.
An example: https://bugzilla.redhat.com/show_bug.cgi?id=927191
Change the default to minstrel which is more robust in such cases.
The ath9k RC code is left in the driver for now, maybe it can
be removed altogether later on.
Cc: stable@vger.kernel.org
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 68d9e1fa24
This change reduces rx sensitivity with no apparent extra benefit.
It looks like it was meant for testing in a specific scenario,
but it was never properly validated.
Cc: rmanohar@qca.qualcomm.com
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Almost all the DMA issues which have plagued ath9k (in station mode)
for years are related to PS. Disabling PS usually "fixes" the user's
connection stablility. Reports of DMA problems are still trickling in
and are sitting in the kernel bugzilla. Until the PS code in ath9k is
given a thorough review, disbale it by default. The slight increase
in chip power consumption is a small price to pay for improved link
stability.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix build error for il_pm_ops if CONFIG_PM is set
but CONFIG_PM_SLEEP is not set.
ERROR: "il_pm_ops" [drivers/net/wireless/iwlegacy/iwl4965.ko] undefined!
ERROR: "il_pm_ops" [drivers/net/wireless/iwlegacy/iwl3945.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: netdev@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This false leak indication is avoided with a no-leak annotation to kmemleak.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to a typo, the current code copies only sizeof(cmd->channels_2)
bytes, which is smaller than the correct sizeof(cmd->channels_5)
size, resulting in a partial scan (some channels are skipped).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The minimum firmware version required for singlerole after recent
driver changes is 6/7.3.10.0.133.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a typo in commit 8675f9 (wlcore/wl12xx/wl18xx: verify
multi-role and single-role fw versions), which was causing the
multirole firmware for wl127x (WiLink6) to be rejected. The actual
minimum version needed for wl127x multirole is 6.5.7.0.42.
Reported-by: Levi Pearson <levipearson@gmail.com>
Reported-by: Michael Scott <hashcode0f@gmail.com>
Cc: stable@kernel.org # 3.9+
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
team_port_enable() adds port to port_hashlist. Reader sees port
in team_get_port_by_index_rcu() and returns it, but
team_get_first_port_txable_rcu() tries to go through port_list, where the
port is not inserted yet -> NULL pointer dereference.
Fix this by reordering port_list and port_hashlist insertion.
Panic is easily triggeable when txing packets and adding/removing port
in a loop.
Introduced by commit 3d249d4c "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
team_get_port_by_index_rcu() might return NULL due to race between port
removal and skb tx path. Panic is easily triggeable when txing packets
and adding/removing port in a loop.
introduced by commit 3d249d4ca "net: introduce ethernet teaming device"
and commit 753f993911 "team: introduce random mode" (for random mode)
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 54f968d6ef
(tuntap: move socket to tun_file) forgets to set SOCK_ZEROCOPY flag, which will
prevent vhost_net from doing zercopy w/ tap. This patch fixes this by setting
it during file open.
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another QMI speaking Qualcomm based device, which should be
driven by qmi_wwan, while cdc_ether should ignore it.
Like on other Huawei devices, the wwan function can appear
either as a single vendor specific interface or as a CDC ECM
class function using separate control and data interfaces.
The ECM control interface protocol is 0xff, likely in an
attempt to indicate that vendor specific management is
required.
In addition to the near standard CDC class, Huawei also add
vendor specific AT management commands to their firmwares.
This is probably an attempt to support non-Windows systems
using standard class drivers. Unfortunately, this part of
the firmware is often buggy. Linux is much better off using
whatever native vendor specific management protocol the
device offers, and Windows uses, whenever possible. This
means QMI in the case of Qualcomm based devices.
The E1820 has been verified to work fine with QMI.
Matching on interface number is necessary to distiguish the
wwan function from serial functions in the single interface
mode, as both function types will have class/subclass/function
set to ff/ff/ff.
The control interface number does not change in CDC ECM mode,
so the interface number matching rule is sufficient to handle
both modes. The cdc_ether blacklist entry is only relevant in
CDC ECM mode, but using a similar interface number based rule
helps document this as a transfer from one driver to another.
Other Huawei 02/06/ff devices are left with the cdc_ether driver
because we do not know whether they are based on Qualcomm chips.
The Huawei specific AT command management is known to be somewhat
hardware independent, and their usage of these class codes may
also be independent of the modem hardware.
Reported-by: Graham Inggs <graham.inggs@uct.ac.za>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the first loop in sh_eth_check_reset() runs to its end, 'cnt' is 0, so the
following check for 'cnt < 0' fails to catch the timeout. Fix the condition in
this check, so that the timeout is actually reported.
While at it, fix the grammar in the failure message...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
was playing with suspend and run into this:
|BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:891
|in_atomic(): 1, irqs_disabled(): 0, pid: 1963, name: bash
|6 locks held by bash/1963:
|CPU: 0 PID: 1963 Comm: bash Not tainted 3.10.0-rc4+ #50
|[<c0014fdc>] (unwind_backtrace+0x0/0xf8) from [<c0011da4>] (show_stack+0x10/0x14)
|[<c0011da4>] (show_stack+0x10/0x14) from [<c02e8680>] (__pm_runtime_idle+0xa4/0xac)
|[<c02e8680>] (__pm_runtime_idle+0xa4/0xac) from [<c0341158>] (davinci_mdio_suspend+0x6c/0x9c)
|[<c0341158>] (davinci_mdio_suspend+0x6c/0x9c) from [<c02e0628>] (platform_pm_suspend+0x2c/0x54)
|[<c02e0628>] (platform_pm_suspend+0x2c/0x54) from [<c02e52bc>] (dpm_run_callback.isra.3+0x2c/0x64)
|[<c02e52bc>] (dpm_run_callback.isra.3+0x2c/0x64) from [<c02e57e4>] (__device_suspend+0x100/0x22c)
|[<c02e57e4>] (__device_suspend+0x100/0x22c) from [<c02e67e8>] (dpm_suspend+0x68/0x230)
|[<c02e67e8>] (dpm_suspend+0x68/0x230) from [<c0072a20>] (suspend_devices_and_enter+0x68/0x350)
|[<c0072a20>] (suspend_devices_and_enter+0x68/0x350) from [<c0072f18>] (pm_suspend+0x210/0x24c)
|[<c0072f18>] (pm_suspend+0x210/0x24c) from [<c0071c74>] (state_store+0x6c/0xbc)
|[<c0071c74>] (state_store+0x6c/0xbc) from [<c02714dc>] (kobj_attr_store+0x14/0x20)
|[<c02714dc>] (kobj_attr_store+0x14/0x20) from [<c01341a0>] (sysfs_write_file+0x16c/0x19c)
|[<c01341a0>] (sysfs_write_file+0x16c/0x19c) from [<c00ddfe4>] (vfs_write+0xb4/0x190)
|[<c00ddfe4>] (vfs_write+0xb4/0x190) from [<c00de3a4>] (SyS_write+0x3c/0x70)
|[<c00de3a4>] (SyS_write+0x3c/0x70) from [<c000e2c0>] (ret_fast_syscall+0x0/0x48)
I don't see a reason why the pm_runtime call must be under the lock.
Further I don't understand why this is a spinlock and not mutex.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Complier may generate codes that re-read the tun->numqueues during
tun_select_queue(). This may be a race if vlan->numqueues were changed in the
same time and can lead unexpected result (e.g. very huge value).
We need prevent the compiler from generating such codes by adding an
ACCESS_ONCE() to make sure tun->numqueues were only read once.
Bug were introduced by commit c8d68e6be1
(tuntap: multiqueue support).
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 091f0ea300 "tg3: Add New 5719 Read
DMA workaround" added a workaround for TX DMA stall on the 5719. This
workaround needs to be applied to the 5720 as well.
Cc: stable@vger.kernel.org
Reported-by: Roland Dreier <roland@purestorage.com>
Tested-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the protocol selector bits (4:0) of the PHY's MII_ADVERTISE
register (ANAR) when writing ADVERTISE_ALL. The protocol selector bits are
indicating IEEE 803.3u support and are fixed / read-only on some PHYs. Not
setting them correctly on others (like TI DP83630) makes the PHY fall back
to 10M HDX mode which should be avoided.
Tested for TI DP83630 PHY on Microblaze platform.
Signed-off-by: Jens Renner <renner@efe-gmbh.de>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was recently found out that GSO on 57710/57711 was broken, due to packets
being sent without a valid IP checksum.
Commit 057cf65 "bnx2x: Fix GSO for 57710/57711 chips" partially fixed this
issue, but failed to set the correct IP checksum when receiving GSO packets
via bridges, as such packets enter bnx2x_tx_split() and the FW flags needed
to calculate IP checksum were erroneously set in the incorrect
buffer descriptor.
This patch re-enables GSO in said scenario for 57710/57711 chips.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If no valid MAC address could be obtained from the hardware,
fall back to a randomly generated one.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW was initialized with data from wrong header, this caused TSO packets
have wrong IP csum.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
here are there fixes for the v3.10 release cycle:
The first patch by Jonas Peterson and Olivier Sobrie fixes the reception of CAN
frames on Kvaser's "USBcan Pro" and "USBcan R" type hardware.
The last two patches by Olivier Sobrie (for esd_usb2) and me (for peak_usb)
change the memory handling for the USB messages from stack to kmalloc(), as
memory used for DMA should not be allocated on stack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC addresses assigned by the PF to VFs were not kept in the PF driver
admin table. As a result, displaying the VF MACs from the PF interface
to user space showed zero address where in fact the VF got non-zero
address from the PF, fix that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VF sense they didn't get MAC address, use random one. This will
address the case of administrator not assigning MAC to the VF through
the PF OS APIs and keep udev happy.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the PF initialization, SRIOV is enabled before the PF is fully initialized.
This allows the kernel to probe the newly-exposed VFs before the PF is ready
to handle them (nested probes).
Have the probe method return the -EPROBE_DEFER value in this situation (instead
of the VF probe method retrying its initialization in a loop, and returning -EIO
on failure). When -EPROBE_DEFER is returned by the VF probe method, the kernel
itself will retry the probe after a suitable delay.
Based upon a suggestion by Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When turning on adaptive_rx under adaptive moderation, the CQ's moderation
count wasn't updated according to rx_frames which resulted in too many
interrupts and bandwidth drop.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smatch reports the following warnings:
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:514 pcan_usb_pro_drv_loaded() error: doing dma on the stack (buffer)
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:878 pcan_usb_pro_init() error: doing dma on the stack (&fi)
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:889 pcan_usb_pro_init() error: doing dma on the stack (&bi)
See "Documentation/DMA-API-HOWTO.txt" section "What memory is DMA'able?"
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
smatch reports the following warnings:
drivers/net/can/usb/esd_usb2.c:640 esd_usb2_start() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:846 esd_usb2_close() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:855 esd_usb2_close() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:923 esd_usb2_set_bittiming() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:1047 esd_usb2_probe() error: doing dma on the stack (&msg)
drivers/net/can/usb/esd_usb2.c:1053 esd_usb2_probe() error: doing dma on the stack (&msg)
See "Documentation/DMA-API-HOWTO.txt" section "What memory is DMA'able?"
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Unlike Kvaser Leaf light devices, some other Kvaser devices (like USBcan
Pro, USBcan R) receive CAN messages in CMD_LOG_MESSAGE frames. This
patch adds support for it.
Cc: linux-stable <stable@vger.kernel.org> # >= v3.8
Signed-off-by: Jonas Peterson <jonas.peterson@gmail.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since the recent addition of 8021AD, we need to set the new field vlan_proto in
sk_buff. Otherwise, it will trigger BUG() call in vlan_proto_idx().
This patch fixes the problem.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the port list dump does not fit into one skb currently the
dump would start over again. Fix this by continue from the last dumped
port.
Introduced by commit d90f889e9c (team: handle sending port list in the
same way option list is sent)
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please pull this batch of fixes intended for the 3.10 stream...
Regarding the NFC bits, Samuel says:
"This is the first batch of NFC fixes for 3.10, and it contains:
- 3 fixes for the NFC MEI support:
* We now depend on the correct Kconfig symbol.
* We register an MEI event callback whenever we enable an NFC device,
otherwise we fail to read anything after an enable/disable cycle.
* We only disable an MEI device from its disable mey_phy_ops,
preventing useless consecutive disable calls.
- An NFC Makefile cleanup, as I forgot to remove a commented out line when
moving the LLCP code to the NFC top level directory."
As for the mac80211 bits, Johannes says:
"This time I have a fix from Stanislaw for a stupid mistake I made in the
auth/assoc timeout changes, a fix from Felix for 64-bit traffic counters
and one from Helmut for address mask handling in mac80211. I also have a
few fixes myself for four different crashes reported by a few people."
And Johannes says this about the iwlwifi bit:
"This fixes a brown paper-bag bug that we really should've caught in
review. More details in the changelog for the fix."
On top of that...
Arend van Spriel and Hante Meuleman cooperate to send a series of AP
and P2P mode fixes for brcmfmac.
Gabor Juhos corrects a register offset for AR9550, avoiding a bus
error.
Dan Carpenter provides a fixup to some dmesg output in the atmel
driver.
And, finally...
Felix Fietkau not only gives us a trio of small AR934x fixes, but
also refactors the ath9k aggregation session start/stop handling
(using the generic mac80211 support) in order to avoid a deadlock.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During a PCI EEH/AER error recovery flow, if the device did not successfully
restart, the error_detected() hook may be called a second time with a
"perm_failure" state. This patch skips over driver cleanup for the second
invocation of the callback.
Also, Lancer error recovery code is fixed-up to handle these changes.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW does not compute L4 checksum for IP Fragmented packets.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently allow changing the mq flag (IFF_MULTI_QUEUE) for a persistent
device. This will result a mismatch between the number the queues in netdev and
tuntap. This is because we only allocate a 1q netdevice when IFF_MULTI_QUEUE was
not specified, so when we set the IFF_MULTI_QUEUE and try to attach more queues
later, netif_set_real_num_tx_queues() may fail which result a single queue
netdevice with multiple sockets attached.
Solve this by disallowing changing the mq flag for persistent device.
Bug was introduced by commit edfb6a148c
(tuntap: reduce memory using of queues).
Reported-by: Sriram Narasimhan <sriram.narasimhan@hp.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman
Yoshihiro Shimoda
Mugunthan V N
Nithin Sujir
Nikolay Aleksandrov
Dinh Nguyen
Somnath Kotur
Jan Beulich
Michael S. Tsirkin
John W. Linville
Kees Cook
Sujith Manoharan
Felix Fietkau
Yijing Wang
Larry Finger
Eliad Peller
Luciano Coelho
Mark A. Greer
Jiri Pirko
Jason Wang
Bjørn Mork
Sergei Shtylyov
Sebastian Siewior
Jens Renner \(EFE\)
Yuval Mintz
Lucas Stach
Dmitry Kravkov
David S. Miller
Or Gerlitz
Jack Morgenstein
Sagi Grimberg
Marc Kleine-Budde
Olivier Sobrie
Jonas Peterson
Haiyang Zhang