This patch fixes accumulating of the header in case packet was requeued
in the error path.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During suspend it is important that all URBs are cancelled and then on
resume re-submitted. This gives initial suspend/resume support.
Based on initial work from Oliver Neukum <oneukum@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the addition of usb_unlink_anchored_urbs() it is possible to fully
control the bulk URBs from the notify callback. There is no need to
schedule work and so only do this for the ISOC URBs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The URB submission routines need more fine grained control for the
mem_flags used by kmalloc(), usb_alloc_urb() and usb_submit_urb() to
better support different caller situations. Add a mem_flags parameter
and give the caller full control.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Join the move away from the obsolete info() macro, opencoding the
remaining uses. While we're at it, also get rid of the warn() macro
by promoting the three remaining uses to err().
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The N_GIGASET_M101 line discipline implemented by the ser_gigaset
driver does not transfer any data from/to userspace through the
tty interface. Therefore a poll method is not needed.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is_pure_response() does "ntohl(var) & const" and then
essentially just tests whether the result is 0 or not; this can be done
more efficiently by computing "var & htonl(const)" instead and doing the
byte swap at compile time instead of run time.
This change slightly shrinks the compiled code; eg on x86-64 we save a
couple of bswapl instructions:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-8 (-8)
function old new delta
t3_sge_intr_msix_napi 544 536 -8
and this also has the pleasant side effect of fixing a sparse warning:
drivers/net/cxgb3/sge.c:2313:15: warning: restricted degrades to integer
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the STMicroelectronics ste10xp PHY device driver.
It supports both the ste100p and the ste101p devices.
Suspend/resume alredy added.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the power management support into the physical
abstraction layer.
Suspend and resume functions respectively turns on/off the bit 11
into the PHY Basic mode control register.
Generic PHY device starts supporting PM.
In order to support the wake-on LAN and avoid to put in power down
the PHY device, the MDIO is aware of what the Ethernet device wants to do.
Voluntary, no CONFIG_PM defines were added into the sources.
Also generic suspend/resume functions are exported to allow
other drivers use them (such as genphy_config_aneg etc.).
Within the phy_driver_register function, we need to remove the
memset. It overrides the device driver owner and it is not good.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the PHY device driver for the National Semiconductor
DP83865 Gig PHYTER.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These warning originate from 50014f1 (ne2: convert to
net_device_ops) which did drop those functions.
drivers/net/ne2.c:140: warning: 'ne_open' declared 'static' but never defined
drivers/net/ne2.c:141: warning: 'ne_close' declared 'static' but never defined
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe_init_interrupt_scheme() is called from ixgbe_resume(). Build that
with CONFIG_PM and without CONFIG_HOTPLUG and you've got a problem.
Several helpers called by it also are misannotated __devinit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the calls necessary to enable advanced error reporting for igb on
systems with AER enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use. This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use. This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use. This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use. This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update FW loading path to accomodate in-kernel images location
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add consistency in alloc_ring() parameter checking
to avoid potential memory leaks.
alloc_ring() callers are correct fo far.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix t3_eth_xmit() missing into the netdev_ops structure.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a regression (introduced by
"p54: more definitions form lmac_longbow.h and pda.h")
It turned out that the "ret" variable wasn't initialized and
this caused the following warnings/errors to appear:
wmaster1: failed to set TX queue parameters for queue 2
wmaster1: failed to set TX queue parameters for queue 3
wmaster1: failed to set TX queue parameters for queue 1
wmaster1: failed to set TX queue parameters for queue 0
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX channel width of the BSS can be obtained only after association.
In all cases, default to HT20 if HT is enabled, and set
chan width to HT40 only if the BSS supports it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make firmware caching on startup optional, and make it default.
When the option is not selected and PM_SLEEP is configured, then
cache firmware in the suspend pm_notifier. This configuration saves
about 64k RAM in normal use, but can lead to a situation where the
driver is configured to use a different firmware.
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Retrieval of external firmware has been resolved, and should work with
the standard orinoco resume algorithm.
This fixes an issue where priv->hw_unavailable indicates the card is
ready when firmware has not been loaded.
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This refactorring will make it easier to share logic with Symbol
firmware.
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We would get an oops on RX on -ENOMEM by passing
NULL to the hardware on ath_rx_buf_link(). The oops
would look something like this:
ath_rx_tasklet+0x515/0x53b
ath9k_tasklet+0x48
tasklet_action
__do_softirq
irq_exit
do_IRQ
RIP: ath_rx_buf_link+0x3a
We correct this by handling the requeue directly on
the ath_rx_tasklet() and trying to allocate an skb
*prior* to sending up the last hardware processed
skb. If we run out of memory this gauranteees we have
skbs to work with while it simply drops new received
frames.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch brings the ath5k eeprom parsing code in sync with the work
done on ath_info by Nick Kossifidis and integrates the missing parts
based on the code of the Atheros Legacy HAL release.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the rate control only with the tx status of first
AMPDU of an aggregation. This patch fixes frequent drops
in throughput.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This instructs FH to increment the retry count of a packet when
it is brought from the memory to TX-FIFO to save transactions
during aggregation flow.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch configures correctly TX DMA channel. It is not
the same as TX queue.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Apply same idiom as in 5000 introduced by
'iwlwifi: define firmware file name once'
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds base band calibration support.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl_clear_stations_table into iwl-sta.c
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes the ad-hoc mode by
1) Removing redundant clear_stations_table which prevented generation of
beacons.
2) Setting assoc_id to 1. It was never set so preventing tx flow
in iwl3945_tx_skb.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure the mac address in add_interface and clear it in
remove_interface so that users can change the mac address
to something other than the one in the eeprom. Also avoid
setting it at attach time so that we won't ack packets
until fully set up.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CHANNEL_CCK flag is set for all 2 Ghz channels, so IS_CHAN_CCK() would
turn out to be true for all channles in that band.
Use IS_CHAN_B() now, which checks the channel mode and not the channel
flags.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, use a helper function to setup RC status data
when processing completed TX descriptors.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Break down huge functions, use helper functions or
macros instead.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace TRUE/FALSE macros with VALID/INVALID macros.
Follow a consistent variable convention.
Remove unnecessary comments.
Add all RC phy macros into a single enum.
Merge functions into reasonably sized entities.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler
Marcel Holtmann
Tilman Schmidt
Roland Dreier
Giuseppe Cavallaro
David S. Miller
Ilpo Järvinen
Al Viro
Alexander Duyck
Jeff Kirsher
Divy Le Ray
John W. Linville
Christian Lamparter
Sujith
David Kilroy
Luis R. Rodriguez
Felix Fietkau
Vasanthakumar Thiagarajan
Abhijeet Kolekar
Bob Copeland