Add the PCI-ID for the upcoming new BMC controller for HP hardware.
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The orion5x-wdt driver is now registered as a platform device and
receives the tclk value as platform data. This fixes a compile issue
cause by a previously removed define "ORION5X_TCLK".
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Kristof Provost <kristof@sigsegv.be>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Martin Michlmayr <tbm@cyrius.com>
Cc: Sylver Bruneau <sylver.bruneau@googlemail.com>
Cc: Kunihiko IMAI <bak@d2.dion.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Make sure that the watchdog is not running after loading
and before it is started by opening /dev/watchdog.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WDT timer ticks quite fast (half of the CPU clock speed, which may
be between 198MHz and 330MHz (or 400MHz on newer boards)). Given it's
size of 32Bit, the maximum timeout value ranges from about 21s to 43s,
depending on the configured CPU clock speed.
This patch add's the timeout module parameter and checks that it's not
bigger then the maximum timeout for the given clock speed.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Clean-up the rc32434 driver code:
- name the platform driver rc32434_wdt_driver
- Replace KBUILD_MODNAME ": " with PFX define.
- Cleanup include files
- Order the ioctl's
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove davinci platform-specific IO accessor macros in favor
of standard ioremap + io[read|write]* functions.
Also, convert printk(KERN_ERR ....) into dev_err(...)
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
I noticed the W83697UG driver tries to register a watchdog even though
it already noticed the chip isn't there.
WDT driver for the Winbond(TM) W83697UG/UF Super I/O chip initialising.
w83697ug/uf WDT: No W83697UG/UF could be found
w83697ug/uf WDT: Watchdog already running. Resetting timeout to 60 sec
w83697ug/uf WDT: cannot register miscdev on minor=130 (err=-16)
Patch propagates the error back to wdt_init().
Signed-off-by: Eric Lammerts <eric@lammerts.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
wait_event_timeout just takes the numnber of jiffies to wait as
an argument. That value does not include jiffies itself.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a recovery is started for a qeth device, additional invocations
to change a mac address, to configure a VLAN interface on top, or to
add multicast addresses should wait till recovery is finished,
otherwise recovery might fail.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth: Unregister MAC addresses from device (layer 2) during
recovery cycle. When the device is set online the MAC
addresses are registered again on the device.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Performance measurements showed EDDP does not lower CPU costs but increase
them. So we dump out EDDP code from qeth driver.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add statistics counter for software tx checksumming.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a way to provide the MAC address for ax88796 devices from
their platform data. Boards might decide to set the address
programmatically, taken from boot tags or other sources.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to the ax88796 ethernet driver to take IRQ flags
given by the platform_device definition.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device ID for a new variant of the 82574 adapter.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Acked-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cxgb3 NIC driver can handle more firmware versions than iw_cxgb3,
and since commit 8207befa ("cxgb3: untie strict FW matching") cxgb3
will load with firmware versions that iw_cxgb3 can't handle. The FW
major number indicates a specific interface between the FW and
iw_cxgb3. Thus if the major number of the running firmware does not
match the required version compiled into iw_cxgb3, then iw_cxgb3 must
not register that device.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
On a timeout call a device specific handler early in the recovery so that
we can complete and process successful commands which timed out due to IRQ
loss or the like rather more elegantly.
[Revised to exclude the timeout handling on a few devices that inherit from
SFF but are not SFF enough to use the default timeout handler]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ipv6 version of bind_conflict code calls ipv6_rcv_saddr_equal()
which at times wrongly identified intersections between addresses.
It particularly broke down under a few instances and caused erroneous
bind conflicts.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Binding to a v4-mapped address on an AF_INET6 socket should
produce the same result as binding to an IPv4 address on
AF_INET socket. The two are interchangable as v4-mapped
address is really a portability aid.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv4 wildcard (0.0.0.0) address does not intersect
in any way with explicit IPv6 addresses. These two should
be permitted, but the IPv4 conflict code checks the ipv6only
bit as part of the test. Since binding to an explicit IPv6
address restricts the socket to only that IPv6 address, the
side-effect is that the socket behaves as v6-only. By
explicitely setting ipv6only in this case, allows the 2 binds
to succeed.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A socket marked v6-only, can not receive or send traffic to v4-mapped
addresses. Thus allowing binding to v4-mapped address on such a
socket makes no sense.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device is signalling that there is data to drain after an error we
should read the bytes out and throw them away. Without this some devices
and controllers get wedged and don't recover.
Based on earlier work by Mark Lord
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ahci_transmit_led_message saves off the led_state
with a value that includes the port number OR'd
in, this incorrect value maybe reported back
in ahci_led_store.
For instance, if you turn off all the leds for
port 1 and cat the value back it will report 1
instead of 0.
# echo 0 > /sys/class/scsi_host/host1/em_message
# cat /sys/class/scsi_host/host1/em_message
1
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make libata more robust when parsing the multi_count
field from a drive's identify data. This prevents us from
attempting to use dubious multi_count values ad infinitum.
Reset dev->multi_count to zero and reprobe it each time
through this routine, as it can change on device reset.
Also ensure that the reported "maximum" value is valid
and is a power of two, and that the reported "count" value
is valid and also a power of two. And that the "count"
value is not greater than the "maximum" value.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For Marvell SoC chips, the HDD LED does not blink when there is
disk I/O if NCQ is enabled. Add a quirk that enables blink mode for
the LED while NCQ is enabled on any port of a SoC host controller.
Normal LED function is restored when NCQ is not enabled on any port.
The code to enable the blink mode is based on earlier code
and suggestions from Frans Pop, Saeed Bishara, and possibly others.
Signed-off-by: Mark Lord <mlord@pobox.com>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable use of the "all ports" IRQ coalescing optimization
for GEN_II / GEN_IIE chips that have dual host-controllers (8-ports).
Currently only the 6081 chip qualifies, but other chips may come along someday.
Rather than each half of the chip having to satisfy a local set of coalescing thresholds,
use of this feature groups all ports together under a single set of thresholds.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add IRQ coalescing to sata_mv (off by default).
This feature can reduce total interrupt overhead for RAID setups
in some situations, by deferring the interrupt signal until one or both of:
a) a specified io_count (completed SATA commands) is achieved, or
b) a specified time interval elapses after an IO completion.
For now, module parameters are used to set the irq_coalescing_io_count
and irq_coalescing_usecs (timeout) globally. These may eventually
be supplemented with sysfs attributes, so that thresholds can be set
on-the-fly and on a per-chip (or even per-host_controller) basis.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Various cosmetic changes in preparation for the IRQ coalescing feature.
Note that the various MV_IRQ_COAL_* definitions are restored/renamed
in the folloup patch which adds IRQ coalescing to the driver.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
platform_get_irq() can return -ENXIO, but since 'irq' is an
unsigned int, it does not show when the IRQ resource wasn't found.
Make irq an int so that we can use a single variable to test the
platform_get_irq() return value.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
According to Alan:
>and yes the EFAR does UDMA66.
mwdma:
>Yep - wrong comment. The EFAR is a sort of clone of the PIIX and I
>copied the comment while EFAR don't appear to have copied the
>limitation
Signed-off-by: Erik Inge Bolsø <knan-lkml@anduin.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As noted by Alan:
>Your suspicions are correct here btw - the device can only do MWDMA1 and
>MWDMA2 (much like some PIIX devices)
Signed-off-by: Erik Inge Bolsø <knan-lkml@anduin.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Blacklist HP Compaq 6720s so that it doesn't play a "spin down,
spin up, spin down" ping-pong with the hard disk during system
power off.
Signed-off-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is initially needed to work around NCQ errata,
whereby the READ_LOG_EXT command sometimes fails
when issued in the traditional (sff) fashion.
Portions of this code will likely be reused for
implementation of the target mode feature later on.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is necessary for use with the upcoming "mv_qc_issue_fis()" patch,
but is being added separately here for easier code review.
When using command issue via the "mv_qc_issue_fis()" mechanism,
the initial ATA_BUSY bit does not show in the ATA status (shadow) register.
This can confuse libata! So here we add a hook to fake ATA_BUSY
for that situation, until the first time a BUSY, DRQ, or ERR bit is seen.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
so that it doesn't miss any protocols. Handle future cases where a
qc is specially marked for polled issue or where a particular chip
version prefers interrupts over polling for PIO.
This mimics the polling decision logic from ata_sff_qc_issue().
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This also gets rid of any need for mv_mode_filter().
Using basic DMA on GEN_IIE requires setting an undocumented
bit in an undocumented register. For safety, we clear that
bit again when switching back to EDMA mode.
To avoid a performance penalty when switching modes,
we cache the register in port_priv, as already done for other regs.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Wim Van Sebroeck
Thomas Mingarelli
Julia Lawall
Thomas Reitmayr
Phil Sutter
Kevin Hilman
Eric Lammerts
Heiko Carstens
Ursula Braun
Klaus-Dieter Wacker
Frank Blaschka
Kay Sievers
David S. Miller
Daniel Mack
Bruce Allan
Roland Dreier
Steve Wise
Alan Cox
Vlad Yasevich
David Milburn
Mark Lord
Florian Fainelli
Erik Inge Bolsø
Maciej Rutecki
Mark Lord