This appends to the L2 Forwarding and L2 Forwarding Parameters tables
(originally added for first-generation switches) the bits that are new
in the second generation.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was inadvertently copied from the SJA1105 E/T structure and not
tested. Cross-checking with the P/Q/R/S documentation (UM11040) makes
it immediately obvious what the correct bit offsets for this field are.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This structure is merely an implementation detail and should be hidden
from the sja1105_dynamic_config.h header, which provides to the rest of
the driver an abstract access to the dynamic configuration interface of
the switch.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_g1_stats_wait has no users outside global1.c, so make it
static.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macros have an extraneous '800' (after 0180C2 there should be just
six nibbles, with X representing one), while the comments have
interchanged c2 and 80 and an extra :00.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When non-bridged, non-vlan'ed mv88e6xxx port is moving down, error
message is logged:
failed to kill vid 0081/0 for device eth_cu_1000_4
This is caused by call from __vlan_vid_del() with vin set to zero, over
call chain this results into _mv88e6xxx_port_vlan_del() called with
vid=0, and mv88e6xxx_vtu_get() called from there returns -EINVAL.
On symmetric path moving port up, call goes through
mv88e6xxx_port_vlan_prepare() that calls mv88e6xxx_port_check_hw_vlan()
that returns -EOPNOTSUPP for zero vid.
This patch changes mv88e6xxx_vtu_get() to also return -EOPNOTSUPP for
zero vid, then this error code is explicitly cleared in
dsa_slave_vlan_rx_kill_vid() and error message is no longer logged.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
Fix sparse warning:
drivers/net/dsa/sja1105/sja1105_static_config.c:446:1: warning:
symbol 'static_config_check_memory_size' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the upper half of a 4-byte STATS_TYPE_PORT statistic ends
up in bits 47:32 of the return value, instead of bits 31:16 as they
should.
Fixes: 6e46e2d821 ("net: dsa: mv88e6xxx: Fix u64 statistics")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PHYLIB and PHYLINK handle fixed-link interfaces differently. PHYLIB
wraps them in a software PHY ("pseudo fixed link") phydev construct such
that .adjust_link driver callbacks see an unified API. Whereas PHYLINK
simply creates a phylink_link_state structure and passes it to
.mac_config.
At the time the driver was introduced, DSA was using PHYLIB for the
CPU/cascade ports (the ones with no net devices) and PHYLINK for
everything else.
As explained below:
commit aab9c4067d
Author: Florian Fainelli <f.fainelli@gmail.com>
Date: Thu May 10 13:17:36 2018 -0700
net: dsa: Plug in PHYLINK support
Drivers that utilize fixed links for user-facing ports (e.g: bcm_sf2)
will need to implement phylink_mac_ops from now on to preserve
functionality, since PHYLINK *does not* create a phy_device instance
for fixed links.
In the above patch, DSA guards the .phylink_mac_config callback against
a NULL phydev pointer. Therefore, .adjust_link is not called in case of
a fixed-link user port.
This patch fixes the situation by converting the driver from using
.adjust_link to .phylink_mac_config. This can be done now in a unified
fashion for both slave and CPU/cascade ports because DSA now uses
PHYLINK for all ports.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter says:
The patch 640f763f98c2: "net: dsa: sja1105: Add support for Spanning
Tree Protocol" from May 5, 2019, leads to the following static
checker warning:
drivers/net/dsa/sja1105/sja1105_main.c:1073 sja1105_stp_state_get()
warn: signedness bug returning '(-22)'
The caller doesn't check for negative errors anyway.
Fixes: 640f763f98c2: ("net: dsa: sja1105: Add support for Spanning Tree Protocol")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The while-loop exit condition check is not correct; the
loop should continue if the returns from the function calls are
negative or the CRC status returns are invalid. Currently it
is ignoring the returns from the function calls. Fix this by
removing the status return checks and only break from the loop
at the very end when we know that all the success condtions have
been met.
Kudos to Dan Carpenter for describing the correct fix and
Vladimir Oltean for noting the change to the check on the number
of retries.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/dsa/sja1105/sja1105_spi.c:486:21: warning: symbol 'sja1105et_regs' was not declared. Should it be static?
drivers/net/dsa/sja1105/sja1105_spi.c:511:21: warning: symbol 'sja1105pqrs_regs' was not declared. Should it be static?
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai26@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several spelling mistakes in dev_err messages. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds functions to add and remove static entries to and from the
forwarding database and dump the full forwarding database.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fast aging per port is not supported directly by the hardware, it is
only possible to configure a global aging time.
Do the fast aging by iterating over the MAC forwarding table and remove
all dynamic entries for a given port.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VLAN aware bridge offloading is similar to the VLAN unaware
offloading, this makes it possible to offload the VLAN bridge
functionalities.
The hardware supports up to 64 VLAN bridge entries, we already use one
entry for each LAN port to prevent forwarding of packets between the
ports when the ports are not in a bridge, so in the end we have 57
possible VLANs.
The VLAN filtering is currently only active when the ports are in a
bridge, VLAN filtering for ports not in a bridge is not implemented.
It is currently not possible to change between VLAN filtering and not
filtering while the port is already in a bridge, this would make the
driver more complicated.
The VLANs are only defined on bridge entries, so we will not add
anything into the hardware when the port joins a bridge if it is doing
VLAN filtering, but only when an allowed VLAN is added.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to offload bridges with DSA to the switch hardware and do
the packet forwarding in hardware.
This implements generic functions to access the switch hardware tables,
which are used to control many features of the switch.
This patch activates the MAC learning by removing the MAC address table
lock, to prevent uncontrolled forwarding of packets between all the LAN
ports, they are added into individual bridge tables entries with
individual flow ids and the switch will do the MAC learning for each
port separately before they are added to a real bridge.
Each bridge consist of an entry in the active VLAN table and the VLAN
mapping table, table entries with the same index are matching. In the
VLAN unaware mode we configure everything with VLAN ID 0, but we use
different flow IDs, the switch should handle all VLANs as normal payload
and ignore them. When the hardware looks for the port of the destination
MAC address it only takes the entries which have the same flow ID of the
ingress packet.
The bridges are configured with 64 possible entries with these
information:
Table Index, 0...63
VLAN ID, 0...4095: VLAN ID 0 is untagged
flow ID, 0..63: Same flow IDs share entries in MAC learning table
port map, one bit for each port number
tagged port map, one bit for each port number
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the special tag in ingress only on the CPU port and not on all
ports. A packet with a special tag could circumvent the hardware
forwarding and should only be allowed on the CPU port where Linux
controls the port.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200)"
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While not explicitly documented as supported in UM10944, compliance with
the STP states can be obtained by manipulating 3 settings at the
(per-port) MAC config level: dynamic learning, inhibiting reception of
regular traffic, and inhibiting transmission of regular traffic.
In all these modes, transmission and reception of special BPDU frames
from the stack is still enabled (not inhibited by the MAC-level
settings).
On ingress, BPDUs are classified by the MAC filter as link-local
(01-80-C2-00-00-00) and forwarded to the CPU port. This mechanism works
under all conditions (even without the custom 802.1Q tagging) because
the switch hardware inserts the source port and switch ID into bytes 4
and 5 of the MAC-filtered frames. Then the DSA .rcv handler needs to put
back zeroes into the MAC address after decoding the source port
information.
On egress, BPDUs are transmitted using management routes from the xmit
worker thread. Again this does not require switch tagging, as the switch
port is programmed through SPI to hold a temporary (single-fire) route
for a frame with the programmed destination MAC (01-80-C2-00-00-00).
STP is activated using the following commands and was tested by
connecting two front-panel ports together and noticing that switching
loops were prevented (one port remains in the blocking state):
$ ip link add name br0 type bridge stp_state 1 && ip link set br0 up
$ for eth in $(ls /sys/devices/platform/soc/2100000.spi/spi_master/spi0/spi0.1/net/);
do ip link set ${eth} master br0 && ip link set ${eth} up; done
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support this, we are creating a make-shift switch tag out of
a VLAN trunk configured on the CPU port. Termination of normal traffic
on switch ports only works when not under a vlan_filtering bridge.
Termination of management (PTP, BPDU) traffic works under all
circumstances because it uses a different tagging mechanism
(incl_srcpt). We are making use of the generic CONFIG_NET_DSA_TAG_8021Q
code and leveraging it from our own CONFIG_NET_DSA_TAG_SJA1105.
There are two types of traffic: regular and link-local.
The link-local traffic received on the CPU port is trapped from the
switch's regular forwarding decisions because it matched one of the two
DMAC filters for management traffic.
On transmission, the switch requires special massaging for these
link-local frames. Due to a weird implementation of the switching IP, by
default it drops link-local frames that originate on the CPU port.
It needs to be told where to forward them to, through an SPI command
("management route") that is valid for only a single frame.
So when we're sending link-local traffic, we are using the
dsa_defer_xmit mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell SOHO switches have several ways to access the internal
registers. One of them being the System Management Interface (SMI),
using the MDC and MDIO pins, with direct and indirect variants.
In preparation for adding support for other register accesses, move
the SMI code into its own files. At the same time, refine the code
to make it clear that the indirect variant is implemented using the
direct variant accessing only two registers for command and data.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow an interrupt number to be passed in the platform data. The
driver will then use it if not zero, otherwise it will poll for
interrupts.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NO_CPU strap is set, the switch starts in 'dumb hub' mode, with
all ports enable. Ports which are then actively used are reconfigured
as required when the driver starts. However unused ports are left
alone. Change this to disable them, and turn off any SERDES
interface. This could save some power and so reduce the temperature a
bit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When requested to disable a port, set the port STP state to disabled.
This fully disables the port and should save some power.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethernet flow control:
The switch MAC does not consume, nor does it emit pause frames. It
simply forwards them as any other Ethernet frame (and since the DMAC is,
per IEEE spec, 01-80-C2-00-00-01, it means they are filtered as
link-local traffic and forwarded to the CPU, which can't do anything
useful with them).
Duplex:
There is no duplex setting in the SJA1105 MAC. It is known to forward
traffic at line rate on the same port in both directions. Therefore it
must be that it only supports full duplex.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resetting the switch at runtime is currently done while changing the
vlan_filtering setting (due to the required TPID change).
But reset is asynchronous with packet egress, and the switch core will
not wait for egress to finish before carrying on with the reset
operation.
As a result, a connected PHY such as the BCM5464 would see an
unterminated Ethernet frame and start to jabber (repeat the last seen
Ethernet symbols - jabber is by definition an oversized Ethernet frame
with bad FCS). This behavior is strange in itself, but it also causes
the MACs of some link partners (such as the FRDM-LS1012A) to completely
lock up.
So as a remedy for this situation, when switch reset is required, simply
inhibit Tx on all ports, and wait for the necessary time for the
eventual one frame left in the egress queue (not even the Tx inhibit
command is instantaneous) to be flushed.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If STP is active, this setting is applied on bridged ports each time an
Ethernet link is established (topology changes).
Since the setting is global to the switch and a reset is required to
change it, resets are prevented if the new callback does not change the
value that the hardware already is programmed for.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN filtering cannot be properly disabled in SJA1105. So in order to
emulate the "no VLAN awareness" behavior (not dropping traffic that is
tagged with a VID that isn't configured on the port), we need to hack
another switch feature: programmable TPID (which is 0x8100 for 802.1Q).
We are reprogramming the TPID to a bogus value which leaves the switch
thinking that all traffic is untagged, and therefore accepts it.
Under a vlan_filtering bridge, the proper TPID of ETH_P_8021Q is
installed again, and the switch starts identifying 802.1Q-tagged
traffic.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation/devicetree/bindings/net/ethernet.txt is confusing because
it says what the MAC should not do, but not what it *should* do:
* "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC
should not add an RX delay in this case)
The gap in semantics is threefold:
1. Is it illegal for the MAC to apply the Rx internal delay by itself,
and simplify the phy_mode (mask off "rgmii-rxid" into "rgmii") before
passing it to of_phy_connect? The documentation would suggest yes.
1. For "rgmii-rxid", while the situation with the Rx clock skew is more
or less clear (needs to be added by the PHY), what should the MAC
driver do about the Tx delays? Is it an implicit wild card for the
MAC to apply delays in the Tx direction if it can? What if those were
already added as serpentine PCB traces, how could that be made more
obvious through DT bindings so that the MAC doesn't attempt to add
them twice and again potentially break the link?
3. If the interface is a fixed-link and therefore the PHY object is
fixed (a purely software entity that obviously cannot add clock
skew), what is the meaning of the above property?
So an interpretation of the RGMII bindings was chosen that hopefully
does not contradict their intention but also makes them more applied.
The SJA1105 driver understands to act upon "rgmii-*id" phy-mode bindings
if the port is in the PHY role (either explicitly, or if it is a
fixed-link). Otherwise it always passes the duty of setting up delays to
the PHY driver.
The error behavior that this patch adds is required on SJA1105E/T where
the MAC really cannot apply internal delays. If the other end of the
fixed-link cannot apply RGMII delays either (this would be specified
through its own DT bindings), then the situation requires PCB delays.
For SJA1105P/Q/R/S, this is however hardware supported and the error is
thus only temporary. I created a stub function pointer for configuring
delays per-port on RXC and TXC, and will implement it when I have access
to a board with this hardware setup.
Meanwhile do not allow the user to select an invalid configuration.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently only the (more difficult) first generation E/T series is
supported. Here the TCAM is only 4-way associative, and to know where
the hardware will search for a FDB entry, we need to perform the same
hash algorithm in order to install the entry in the correct bin.
On P/Q/R/S, the TCAM should be fully associative. However the SPI
command interface is different, and because I don't have access to a
new-generation device at the moment, support for it is TODO.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this moment the following is supported:
* Link state management through phylib
* Autonomous L2 forwarding managed through iproute2 bridge commands.
IP termination must be done currently through the master netdevice,
since the switch is unmanaged at this point and using
DSA_TAG_PROTO_NONE.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the driver can be probed as an mdio device, remove the legacy
DSA platform device probing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probing DSA devices as platform devices has been superseded by using
normal bus drivers. Add support for probing the mv88e6060 device as an
mdio device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
While possible (and safe) to use the newly introduced
dsa_port_is_vlan_filtering helper, fabricating a dsa_port pointer is a
bit awkward, so simply retrieve this from the dsa_switch structure.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since DSA has recently learned to treat better with drivers that set
vlan_filtering_is_global, doing this is no longer required.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was recently introduced, so keeping state inside the driver is no
longer necessary.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver, recognizing that the .port_vlan_filtering callback was never
coming after the port left its parent bridge, decided to take that duty
in its own hands. DSA now takes care of this condition, so fix that.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA core is now able to do this check prior to calling the
.port_vlan_filtering callback, so tell it that VLAN filtering is global
for this particular hardware.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "fs->location" is a u32 that comes from the user in ethtool_set_rxnfc().
We can't pass unclamped values to test_bit() or it results in an out of
bounds access beyond the end of the bitmap.
Fixes: 7318166cac ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the legacy method of probing the mv88e6xxx driver, now that all
the mainline boards have been converted to use mdio based probing for
a number of cycles.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The REG_READ macro contains a return statement, making it not very
safe. Remove it by inlining the code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The REG_WRITE macro contains a return statement, making it not very
safe. Remove it by inlining the code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass around priv, not ds. This will help with changing to an mdio
driver, and makes this driver more like mv88e6xxx.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an SPDX header, and remove the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink will call the mac_config() callback once per second when
polling a PHY or a fixed link. The MAC driver is not supposed to
reconfigure the MAC if nothing has changed.
Make the mv88e6xxx driver look at the current configuration of the
port, and return early if nothing has changed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/dsa/microchip/ksz9477.c: In function ‘ksz9477_get_interface’:
drivers/net/dsa/microchip/ksz9477.c:1145:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (gbit)
^
drivers/net/dsa/microchip/ksz9477.c:1147:2: note: here
case 0:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches fixes few issues in mv88e6390x_port_set_cmode().
1. When entering the function the old cmode may be 0, in this case
mv88e6390x_serdes_get_lane() returns -ENODEV. As result we bail
out and have no chance to set a new mode. Therefore deal properly
with -ENODEV.
2. Once we have disabled power and irq, let's set the cached cmode to 0.
This reflects the actual status and is cleaner if we bail out with an
error in the following function calls.
3. The cached cmode is used by mv88e6390x_serdes_get_lane(),
mv88e6390_serdes_power_lane() and mv88e6390_serdes_irq_enable().
Currently we set the cached mode to the new one at the very end of
the function only, means until then we use the old one what may be
wrong.
4. When calling mv88e6390_serdes_irq_enable() we use the lane value
belonging to the old cmode. Get the lane belonging to the new cmode
before calling this function.
It's hard to provide a good "Fixes" tag because quite a few smaller
changes have been done to the code in question recently.
Fixes: d235c48b40 ("net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This partially reverts ed8fe20205 ("net: dsa: mv88e6xxx: prevent
interrupt storm caused by mv88e6390x_port_set_cmode"). I missed
that chip->ports[].cmode is overwritten anyway by the cmode
caching in mv88e6xxx_setup().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements accessors for the QCA8337 MDIO access
through the MDIO_MASTER register, which makes it possible to
access the PHYs on slave-bus through the switch. In cases
where the switch ports are already mapped via external
"phy-phandles", the internal mdio-bus is disabled in order to
prevent a duplicated discovery and enumeration of the same
PHYs. Don't use mixed external and internal mdio-bus
configurations, as this is not supported by the hardware.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This belated patch implements Andrew Lunn's request of
"remove the phy_read() and phy_write() functions."
<https://lore.kernel.org/patchwork/comment/902734/>
While seemingly harmless, this causes the switch's user
port PHYs to get registered twice. This is because the
DSA subsystem will create a slave mdio-bus not knowing
that the qca8k_phy_(read|write) accessors operate on
the external mdio-bus. So the same "bus" gets effectively
duplicated.
Cc: stable@vger.kernel.org
Fixes: 6b93fb4648 ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful, we use a dev_info() print which already
displays the platform device's address.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, the switch driver is expected to configure CPU and DSA
ports to their maximum speed. For the 6341 and 6390 families, the
ports interface mode has to be configured as well. The 6390X range
support 10G ports using XAUI, while the 6341 and 6390 supports
2500BaseX, as their maximum speed.
Fixes: 787799a9d5 ("net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original patch I missed to add mv88e6xxx_ports_cmode_init()
to the second probe function, the one for the new DSA framework.
Fixes: ed8fe20205 ("net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmode")
Reported-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an external PHY is connected via SGMII and uses in-band signalling
then the auto-negotiated values aren't propagated to the port,
resulting in a broken link. See discussion in [0]. This patch adds
this propagation. We need to call mv88e6xxx_port_setup_mac(),
therefore export it from chip.c.
Successfully tested on a ZII DTU with 88E6390 switch and an
Aquantia AQCS109 PHY connected via SGMII to port 9.
[0] https://marc.info/?t=155130287200001&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ports 9 and 10 don't have internal PHY's but are (dependent on the
version) SERDES/SGMII/XAUI/RXAUI ports.
v2:
- fix it for all 88E6x90 family members
Fixes: bc3931557d ("net: dsa: mv88e6xxx: Add number of internal PHYs")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing another issue I faced the problem that
mv88e6xxx_port_setup_mac() failed due to DUPLEX_UNKNOWN being passed
as argument to mv88e6xxx_port_set_duplex(). We should handle this case
gracefully and return -EOPNOTSUPP, like e.g. mv88e6xxx_port_set_speed()
is doing it.
Fixes: 7f1ae07b51 ("net: dsa: mv88e6xxx: add port duplex setter")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add KSZ9893 switch support in KSZ9477 driver. This switch is similar to
KSZ9477 except the ingress tail tag has 1 byte instead of 2 bytes, so
KSZ9893 tagging will be used.
The XMII register that governs how the host port communicates with the
MAC also has different register definitions.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Despite what the datesheet says, the silicon implements the older way
of snapshoting the statistics. Change the op.
Reported-by: Chris.Healy@zii.aero
Tested-by: Chris.Healy@zii.aero
Fixes: 0ac64c3949 ("net: dsa: mv88e6xxx: mv88e6161 uses mv88e6320 stats snapshot")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When debugging another issue I faced an interrupt storm in this
driver (88E6390, port 9 in SGMII mode), consisting of alternating
link-up / link-down interrupts. Analysis showed that the driver
wanted to set a cmode that was set already. But so far
mv88e6390x_port_set_cmode() doesn't check this and powers down
SERDES, what causes the link to break, and eventually results in
the described interrupt storm.
Fix this by checking whether the cmode actually changes. We want
that the very first call to mv88e6390x_port_set_cmode() always
configures the registers, therefore initialize port.cmode with
a value that is different from any supported cmode value.
We have to take care that we only init the ports cmode once
chip->info->num_ports is set.
v2:
- add small helper and init the number of actual ports only
Fixes: 364e9d7776 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon setting the cmode on 6390 and 6390X, the associated serdes
interfaces must be powered off/on.
Both 6390X and 6390 share code to do so, but it currently uses the 6390
specific helper mv88e6390_serdes_power() to disable and enable the
serdes interface.
This call will fail silently on 6390X when trying so set a 10G interface
such as XAUI or RXAUI, since mv88e6390_serdes_power() internally grabs
the lane number based on modes supported by the 6390, and returns 0 when
getting -ENODEV as a lane number.
Using mv88e6390x_serdes_power() should be safe here, since we explicitly
rule-out all ports but the 9 and 10, and because modes supported by 6390
ports 9 and 10 are a subset of those supported on 6390X.
This was tested on 6390X using RXAUI mode.
Fixes: 364e9d7776 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch maintains u64 counters for the number of octets sent and
received. These are kept as two u32's which need to be combined. Fix
the combing, which wrongly worked on u16's.
Fixes: 80c4627b27 ("dsa: mv88x6xxx: Refactor getting a single statistic")
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Topaz family should have different phylink_validate method from the
Peridot, since on Topaz the port supporting 2500BaseX mode is port 5,
not 9 and 10.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 787799a9d5 sets the SERDES interfaces of 6390 and 6390X to
1000BaseX, but this is only needed on 6390X, since there are SERDES
interfaces which can be used on lower ports on 6390.
This commit fixes this by returning to previous behaviour on 6390.
(Previous behaviour means that CMODE is not set at all if requested mode
is NA).
This is needed on Turris MOX, where the 88e6190 is connected to CPU in
2500BaseX mode.
Fixes: 787799a9d5 ("net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to hold the register lock while requesting the GPIO
interrupt. By not holding it we can also avoid a false positive
lockdep splat.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following false positive lockdep splat has been observed.
======================================================
WARNING: possible circular locking dependency detected
4.20.0+ #302 Not tainted
------------------------------------------------------
systemd-udevd/160 is trying to acquire lock:
edea6080 (&chip->reg_lock){+.+.}, at: __setup_irq+0x640/0x704
but task is already holding lock:
edff0340 (&desc->request_mutex){+.+.}, at: __setup_irq+0xa0/0x704
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&desc->request_mutex){+.+.}:
mutex_lock_nested+0x1c/0x24
__setup_irq+0xa0/0x704
request_threaded_irq+0xd0/0x150
mv88e6xxx_probe+0x41c/0x694 [mv88e6xxx]
mdio_probe+0x2c/0x54
really_probe+0x200/0x2c4
driver_probe_device+0x5c/0x174
__driver_attach+0xd8/0xdc
bus_for_each_dev+0x58/0x7c
bus_add_driver+0xe4/0x1f0
driver_register+0x7c/0x110
mdio_driver_register+0x24/0x58
do_one_initcall+0x74/0x2e8
do_init_module+0x60/0x1d0
load_module+0x1968/0x1ff4
sys_finit_module+0x8c/0x98
ret_fast_syscall+0x0/0x28
0xbedf2ae8
-> #0 (&chip->reg_lock){+.+.}:
__mutex_lock+0x50/0x8b8
mutex_lock_nested+0x1c/0x24
__setup_irq+0x640/0x704
request_threaded_irq+0xd0/0x150
mv88e6xxx_g2_irq_setup+0xcc/0x1b4 [mv88e6xxx]
mv88e6xxx_probe+0x44c/0x694 [mv88e6xxx]
mdio_probe+0x2c/0x54
really_probe+0x200/0x2c4
driver_probe_device+0x5c/0x174
__driver_attach+0xd8/0xdc
bus_for_each_dev+0x58/0x7c
bus_add_driver+0xe4/0x1f0
driver_register+0x7c/0x110
mdio_driver_register+0x24/0x58
do_one_initcall+0x74/0x2e8
do_init_module+0x60/0x1d0
load_module+0x1968/0x1ff4
sys_finit_module+0x8c/0x98
ret_fast_syscall+0x0/0x28
0xbedf2ae8
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&desc->request_mutex);
lock(&chip->reg_lock);
lock(&desc->request_mutex);
lock(&chip->reg_lock);
&desc->request_mutex refer to two different mutex. #1 is the GPIO for
the chip interrupt. #2 is the chained interrupt between global 1 and
global 2.
Add lockdep classes to the GPIO interrupt to avoid this.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port_cleanup function to reset some device variables when the port is
disabled. Add a mutex to make sure changing those variables is
thread-safe.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary header include.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get port link status to know whether to read MIB counters when the link
is going down.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add background MIB counter reading support.
Port MIB counters should only be read when there is link. Otherwise it is
a waste of time as hardware never increases those counters. There are
exceptions as some switches keep track of dropped counts no matter what.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare PHY for proper advertisement as sometimes the PHY in the switch
has its own problems even though it may share the PHY id from regular PHY
but the fixes in the PHY driver do not apply.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the file names of the FW files which this driver handles into
the module description.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not specifying an explicit format argument but instead passing a
string litteral which causes these two warnings to show up:
drivers/net/dsa/mv88e6xxx/chip.c: In function
'mv88e6xxx_irq_poll_setup':
drivers/net/dsa/mv88e6xxx/chip.c:483:2: warning: format not a string
literal and no format arguments [-Wformat-security]
chip->kworker = kthread_create_worker(0, dev_name(chip->dev));
^~~~
drivers/net/dsa/mv88e6xxx/ptp.c: In function 'mv88e6xxx_ptp_setup':
drivers/net/dsa/mv88e6xxx/ptp.c:403:4: warning: format not a string
literal and no format arguments [-Wformat-security]
dev_name(chip->dev));
^~~~~~~~
LD [M] drivers/net/dsa/mv88e6xxx/mv88e6xxx.o
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the bridge flags to Marvell 88e6xxx bridges, allowing
the multicast and unicast flood properties to be controlled. These
can be controlled on a per-port basis via commands such as:
bridge link set dev lan1 flood on|off
bridge link set dev lan1 mcast_flood on|off
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII_ID specifies that we should have internal delay, so resurrect the
delay addition routine but under the RGMII_ID mode.
Fixes: 40269aa9f40a ("net: dsa: qca8k: disable delay for RGMII mode")
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/dsa/bcm_sf2_cfp.c: In function 'bcm_sf2_cfp_ipv6_rule_set':
drivers/net/dsa/bcm_sf2_cfp.c:606:40: warning:
variable 'v6_m_spec' set but not used [-Wunused-but-set-variable]
drivers/net/dsa/bcm_sf2_cfp.c:606:30: warning:
variable 'v6_spec' set but not used [-Wunused-but-set-variable]
It not used any more after commit e4f7ef54cb ("dsa: bcm_sf2: use flow_rule
infrastructure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPU port is special and does not need to obey VLAN restrictions as
far as untagged traffic goes, also, having the CPU port be part of a
particular PVID is against the idea of keeping it tagged in all VLANs.
Fixes: ca89319483 ("net: dsa: b53: Keep CPU port as tagged in all VLANs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We assume in the bcm_sf2 driver that the DSA master network device
supports ethtool_ops::{get,set}_wol operations, which is not a given.
Avoid de-referencing potentially non-existent function pointers and
check them as we should.
Fixes: 96e65d7f3f ("net: dsa: bcm_sf2: add support for Wake-on-LAN")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN filtering can be built into the kernel, and also dynamically turned
on/off through the bridge master device. Allow re-configuring the switch
appropriately to account for that by deciding whether VLAN table
(v_table) misses should lead to a drop or forward.
Fixes: a2482d2ce3 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were not consistent in how the default VID of a given port was
defined, b53_br_leave() would make sure the VLAN ID would be either 0/1
depending on the switch generation, but b53_configure_vlan(), which is
the default configuration would unconditionally set it to 1. The correct
value is 1 for 5325/5365 series and 0 otherwise. To avoid repeating that
mistake ever again, introduce a helper function: b53_default_pvid() to
factor that out.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of ->num_ports comes from bcm_sf2_sw_probe() and it is less
than or equal to DSA_MAX_PORTS. The ds->ports[] array is used inside
the dsa_is_user_port() and dsa_is_cpu_port() functions. The ds->ports[]
array is allocated in dsa_switch_alloc() and it has ds->num_ports
elements so this leads to a static checker warning about a potential out
of bounds read.
Fixes: 8cfa94984c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO interrupt controller on the espressobin board only supports edge interrupts.
If one enables the use of hardware interrupts in the device tree for the 88E6341, it is
possible to miss an edge. When this happens, the INTn pin on the Marvell switch is
stuck low and no further interrupts occur.
I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is
a race in handling device interrupts (e.g. PHY link interrupts). Some interrupts are
directly cleared by reading the Global 1 status register. However, the device interrupt
flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced.
This is done by reading the relevant SERDES and PHY status register.
The code only services interrupts whose status bit is set at the time of reading its status
register. If an interrupt event occurs after its status is read and before all interrupts
are serviced, then this event will not be serviced and the INTn output pin will remain low.
This is not a problem with polling or level interrupts since the handler will be called
again to process the event. However, it's a big problem when using level interrupts.
The fix presented here is to add a loop around the code servicing switch interrupts. If
any pending interrupts remain after the current set has been handled, we loop and process
the new set. If there are no pending interrupts after servicing, we are sure that INTn has
gone high and we will get an edge when a new event occurs.
Tested on espressobin board.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag offload_fwd_mark is set as the switch can forward frames by
itself.
This can be considered a fix to a problem introduced in commit
c2e866911e where the port membership are not set in sync. The flag
offload_fwd_mark just needs to be set in tag_ksz.c to prevent the software
bridge from forwarding duplicate multicast frames.
Fixes: c2e866911e ("microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using an external PHY, ports 9 and 10 can support 2500BaseT.
So set this link mode in the mask when validating.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the source and destination port of a CFP rule match, we must set
the loopback bit enable to allow that, otherwise the frame is discarded.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return CFP policer statistics (Green, Yellow or Red) as part of the
standard ethtool statistics. This helps debug when CFP rules may not be
hit (0 counter).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding CFP statistics, we will need to overlay the
standard B53 statistics, so create specific bcm_sf2_sw_* functions to
call into their b53_common.c counterpart.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer need a dedicated statistics mutex since we leverage
b53_common for statistics now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the issues with non BCM58XX chips in the b53 driver
failing, when the irq is not specified in the device tree.
Removed the check for BCM58XX in b53_srab_prepare_irq(),
so the 'port->irq' will be set to '-EXIO' if the irq is not
specified in the device tree.
Fixes: 16994374a6 ("net: dsa: b53: Make SRAB driver manage port interrupts")
Fixes: b2ddc48a81 ("net: dsa: b53: Do not fail when IRQ are not initialized")
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On one hand, the mv88e6xxx driver has a work queue called in loop
which will attempt register accesses after MDIO bus suspension, that
entirely freezes the platform during suspend.
On the other hand, the DSA core is not ready yet to support suspend to
RAM operation because so far there is no way to recover reliably the
switch configuration.
To avoid the kernel to freeze when suspending with a switch driven by
the mv88e6xxx driver, we choose to prevent the driver suspension and
in the same way, the whole platform.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update this driver to use the flow_rule infrastructure, hence we can use
the same code to populate hardware IR from ethtool_rx_flow and the
cls_flower interfaces.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ATU port vector contains a bit per port of the switch. The code
wrongly used it as a port number, and incremented a port counter. This
resulted in the wrong interfaces counter being incremented, and
potentially going off the end of the array of ports.
Fix this by using the source port ID for the violation, which really
is a port number.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Tested-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 65f60e4582 ("net: dsa: mv88e6xxx: Keep ATU/VTU violation statistics")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users of the fixed_phy_add() pass -1 as GPIO number
to the fixed phy driver, and all users of fixed_phy_register()
pass -1 as GPIO number as well, except for the device
tree MDIO bus.
Any new users should create a proper device and pass the
GPIO as a descriptor associated with the device so delete
the GPIO argument from the calls and drop the code looking
requesting a GPIO in fixed_phy_add().
In fixed phy_register(), investigate the "fixed-link"
node and pick the GPIO descriptor from "link-gpios" if
this property exists. Move the corresponding code out
of of_mdio.c as the fixed phy code anyways requires
OF to be in use.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MediaTek MT7621 SoC device contains a 7530 switch, and the existing
linux kernel 7530 DSA switch driver can be used with it.
The bulk of the changes required stem from the 7621 having different
regulator and pad setup. The existing setup of these in the 7530
driver appears to be very specific to its implemtation in the Mediatek
7623 SoC. (Not entirely surprising given the 7623 is a quad core ARM
based SoC, and the 7621 is a dual core, dual thread MIPS based SoC).
Create a new devicetree type, "mediatek,mt7621", to support the 7530
switch in the 7621 SoC. There appears to be no usable ID register to
distinguish it from a 7530 in other hardware at runtime. This is used
to carry out the appropriate configuration and setup.
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Duec to a typo, mv88e6390_serdes_irq_setup() calls itself, rather than
mv88e6390x_serdes_irq_setup(). It then blows the stack, and shortly
after the machine blows up.
Fixes: 2defda1f4b ("net: dsa: mv88e6xxx: Add support for SERDES on ports 2-8 for 6390X")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In RGMII mode we should not have any delay in port MAC, so disable
the delay.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new of_get_compatible_child() helper to look up child nodes to
avoid ever matching non-child nodes elsewhere in the tree.
Also fix up the related struct device_node leaks.
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: stable <stable@vger.kernel.org> # 4.19: 36156f9241
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform-device driver data is set on successful probe and will
never be NULL on remove (or we have much bigger problems).
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new of_get_compatible_child() helper to look up child nodes to
avoid ever matching non-child nodes elsewhere in the tree.
Also fix up the related struct device_node leaks.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable <stable@vger.kernel.org> # 4.20
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to disable and deregister the switch on late probe errors to
avoid use-after-free when the device-resource-managed switch is freed.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable <stable@vger.kernel.org> # 4.20
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 copper ports have an errata which require poking magic values
into undocumented magic registers and then performing a software
reset.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver uses GPIO descriptors only, <linux/of_gpio.h>
is not used so drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver does not use the old GPIO includes so drop
them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both bcm_sf2_sw_indir_rw and mdiobus_write_nested could fail, so let's
return their error codes upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port partitioning is done by enabling UNICAST_VLAN_BOUNDARY and changing
the default port membership of 0x7f to other values such that there is
no communication between ports. In KSZ9477 the member for port 1 is
0x41; port 2, 0x42; port 3, 0x44; port 4, 0x48; port 5, 0x50; and port 7,
0x60. Port 6 is the host port.
Setting a zero value can be used to stop port from receiving.
However, when UNICAST_VLAN_BOUNDARY is disabled and the unicast addresses
are already learned in the dynamic MAC table, setting zero still allows
devices connected to those ports to communicate. This does not apply to
multicast and broadcast addresses though. To prevent these leaks and
make the function of port membership consistent UNICAST_VLAN_BOUNDARY
should never be disabled.
Note that UNICAST_VLAN_BOUNDARY is enabled by default in KSZ9477.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6320 family of switches uses the same watchdog registers as the
6390.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ethtool_regs version is set to 0 for all DSA drivers.
Use this field to store the chip ID to simplify the pretty dump of
any interfaces registered by the "dsa" driver.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the tag Kconfig option and related macros in preparation for
addition of new KSZ family switches with different tag formats.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to handle optional reset GPIO in the KSZ switch driver. The switch
has a reset GPIO line which can be controlled by the CPU, so make sure it is
configured correctly in such setups.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable hardware level MAC learning because it breaks station roaming.
When enabled it drops all frames that arrive from a MAC address
that is on a different port at learning table.
Signed-off-by: Anderson Luiz Alves <alacn1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ksz_9477_reg.h to ksz9477_reg.h for consistency as the product
name is always KSZ####.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Break KSZ9477 DSA driver into two files in preparation to add more KSZ
switch drivers.
Add common functions in ksz_common.h so that other KSZ switch drivers
can access code in ksz_common.c.
Add ksz_spi.h for common functions used by KSZ switch SPI drivers.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ksz_spi.c to ksz9477_spi.c and update Kconfig in preparation to add
more KSZ switch drivers.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename some functions with ksz9477 prefix to separate chip specific code
from common code.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up code according to patch check suggestions.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace license with GPL.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have a workaround for a couple of switches whose internal
PHYs only have the Marvel OUI, but no model number. We detect such
PHYs and give them the 6390 ID as the model number. However the
mv88e6161 has two SERDES interfaces in the same address range as its
internal PHYs. These suffer from the same problem, the Marvell OUI,
but no model number. As a result, these SERDES interfaces were getting
the same PHY ID as the mv88e6390, even though they are not PHYs, and
the Marvell PHY driver was trying to drive them.
Add a special case to stop this from happen.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6161 would sometime fail to probe with a timeout waiting for
the switch to complete an operation. This operation is supposed to
clear the statistics counters. However, due to a read/modify/write,
without the needed mask, the operation actually carried out was more
random, with invalid parameters, resulting in the switch not
responding. We need to preserve the histogram mode bits, so apply a
mask to keep them.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 40cff8fca9 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390X family has 8 SERDES interfaces. When ports 9 and 10 are not
using all their SERDES interfaces, the unused ones can be assigned to
ports 2-8. Add support for interrupts from SERDES interfaces connected
to these lower ports.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390X family has 8 SERDES interfaces. This allows ports 9 and 10
to support up to 10Gbps using 4 SERDES interfaces. However, when lower
speeds are used, which need fewer SERDES interfaces, the unused SERDES
interfaces can be used by ports 2-8.
The hardware defaults to ports 9 and 10 having all 4 SERDES interfaces
assigned to them. This only gets changed when the interface is
configured after what the SFP supports has been determined, or the 10G
PHY completes auto-neg.
For hardware designs which limit ports 9 and 10 to one or two SERDES
interfaces, and place SFPs on the lower interfaces, this is too
late. Those ports with SFP should not wait until ports 9/10 are up in
order to get access to the SERDES interface. So change the default
configuration when the driver is initialised. Configure ports 9 and 10
to 1000BaseX, so they use a single SERDES interface, freeing up the
others. They can steal them back if they need them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The X family variants support additional ports modes, for 10G
operation, which the non-X variants don't have. Add a port_set_cmode()
for non-X variants to enforce this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are binding to the PHY using the SF2 slave MDIO bus that we create,
binding involves reading the PHY's MII_PHYSID1/2 which won't be possible
if the PHY is turned off. Temporarily turn it on/off for the bus probing
to succeeed. This fixes unbind/bind problems where the port connecting
to that PHY would be in error since it could not connect to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have migrated the CFP rule handling to a list with a
software copy, the delete/get operation just returns what is on the
list, no need to read from the hardware which is both slow and more
error prone.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware can lose its context during system suspend, and depending
on the switch generation (7445 vs. 7278), while the rules are still
there, they will have their valid bit cleared (because that's the
fastest way for the HW to reset things). Just make sure we re-apply them
coming back from resume. The 7445 switch is an older version of the core
that has some quirky RAM technology requiring a delete then re-inser to
guarantee the RAM entries are properly latched.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for restoring CFP rules during system wide system
suspend/resume where the hardware loses its context, split the rule
validation from its actual insertion as well as the rule removal from
its actual hardware deletion operation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We tried hard to use the hardware as a storage area, which made things
needlessly complex in that we had to both marshall and unmarshall the
ethtool_rx_flow_spec into what the CFP hardware understands but it did
not require any driver level allocations, so that was nice.
Keep a copy of the ethtool_rx_flow_spec rule we want to insert, and also
make sure we don't have a duplicate rule already. This greatly speeds up
the deletion time since we only need to clear the slice's valid bit and
not perform a full read.
This is a preparatory step for being able to restore rules upon system
resumption where the hardware loses its context partially or entirely.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize mutex before use. Avoid kernel complaint when
CONFIG_DEBUG_LOCK_ALLOC is enabled.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a fix for the port_set_speed method for the Topaz family.
Currently the same method is used as for the Peridot family, but
this is wrong for the SERDES port.
On Topaz, the SERDES port is port 5, not 9 and 10 as in Peridot.
Moreover setting alt_bit on Topaz only makes sense for port 0 (for
(differentiating 100mbps vs 200mbps). The SERDES port does not
support more than 2500mbps, so alt_bit does not make any difference.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to open code what the switch setup function does, in
fact, because we just issued a switch reset, we would make all the
register get their default values, including for instance, having unused
port be enabled again and wasting power and leading to an inappropriate
switch core clock being selected.
Fixes: 8cfa94984c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order in which we release resources is unfortunately leading to bus
errors while dismantling the port. This is because we set
priv->wol_ports_mask to 0 to tell bcm_sf2_sw_suspend() that it is now
permissible to clock gate the switch. Later on, when dsa_slave_destroy()
comes in from dsa_unregister_switch() and calls
dsa_switch_ops::port_disable, we perform the same dismantling again, and
this time we hit registers that are clock gated.
Make sure that dsa_unregister_switch() is the first thing that happens,
which takes care of releasing all user visible resources, then proceed
with clock gating hardware. We still need to set priv->wol_ports_mask to
0 to make sure that an enabled port properly gets disabled in case it
was previously used as part of Wake-on-LAN.
Fixes: d9338023fb ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c499696e79 ("net: dsa: b53: Stop using dev->cpu_port
incorrectly") was a bit too trigger happy in removing the CPU port from
the VLAN membership because we rely on DSA to program the CPU port VLAN,
which it does, except it does not bother itself with tagged/untagged and
just usese untagged.
Having the CPU port "follow" the user ports tagged/untagged is not great
and does not allow for properly differentiating, so keep the CPU port
tagged in all VLANs.
Reported-by: Gerhard Wiesinger <lists@wiesinger.com>
Fixes: c499696e79 ("net: dsa: b53: Stop using dev->cpu_port incorrectly")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to convert the local advertising to an LCL capabilities,
which is then used to resolve pause flow control settings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When B53_SERDES is a loadable module, a built-in srab driver still
cannot reach it, so the previous fix is incomplete:
b53_srab.c:(.text+0x3f4): undefined reference to `b53_serdes_init'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe64): undefined reference to `b53_serdes_link_state'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe74): undefined reference to `b53_serdes_link_set'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe88): undefined reference to `b53_serdes_an_restart'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea0): undefined reference to `b53_serdes_phylink_validate'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea4): undefined reference to `b53_serdes_config'
Add a Kconfig dependency that forces srab to also be a module
in this case, but allow it to be built-in when serdes is
disabled or built-in.
Fixes: 7a8c7f5c30 ("net: dsa: b53: Fix build with B53_SRAB enabled and not B53_SERDES")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses devm_ioremap_resource() which is only available when
CONFIG_HAS_IOMEM is set, make the driver depend on this config option.
User mode Linux does not have CONFIG_HAS_IOMEM set and the driver was
failing on this architecture.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In both 802.3z and SGMII modes we need to configure the MAC accordingly
to flip between Fiber and SGMII modes, and we need to read the MAC
status from the SGMII in-band control word.
Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maths went wrong, to get 0x20, we need to do 0x1e + (x) * 2, not 0x18,
fix that offset so we access the correct registers. This would make us
not access the correct SerDes Digital control words, status would be
fine and so we would not be correctly flipping between Fiber and SGMII
modes resulting in incorrect status words being pulled into the SerDes
digital status register.
Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHYLINK takes care of filing the right information into
state->an_enabled, get rid of the read from the SerDes's BMCR register.
Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new tls tests added in parallel in both net and net-next.
Used Stephen Rothwell's linux-next resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put has taken the null pointer check into account. So it is
safe to remove the duplicated check before of_node_put.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use one code block when returning because the interface type is
unsupported and also check if some unsupported port gets configured.
In addition fix a double the and use dsa_is_cpu_port() instated of
manually getting the CPU port.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value from of_reset_control_array_get_exclusive() is not
checked correctly. The test is done against a wrong variable. This
patch fix it.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a cut/paste error and a typo which results in ATU miss violations
not being reported.
Fixes: 0977644c50 ("net: dsa: mv88e6xxx: Decode ATU problem interrupt")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the Device Tree is not providing the per-port interrupts, do not fail
during b53_srab_irq_enable() but instead bail out gracefully. The SRAB driver
is used on the BCM5301X (Northstar) platforms which do not yet have the SRAB
interrupts wired up.
Fixes: 16994374a6 ("net: dsa: b53: Make SRAB driver manage port interrupts")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the DSA driver for the GSWIP Switch found in the VRX200 SoC.
This switch is integrated in the DSL SoC, this SoC uses a GSWIP version
2.1, there are other SoCs using different versions of this IP block, but
this driver was only tested with the version found in the VRX200.
Currently only the basic features are implemented which will forward all
packages to the CPU and let the CPU do the forwarding. The hardware also
support Layer 2 offloading which is not yet implemented in this driver.
The GPHY FW loaded is now done by this driver and not any more by the
separate driver in drivers/soc/lantiq/gphy.c, I will remove this driver
is a separate patch. to make use of the GPHY this switch driver is
needed anyway. Other SoCs have more embedded GPHYs so this driver should
support a variable number of GPHYs. After the firmware was loaded the
GPHY can be probed on the MDIO bus and it behaves like an external GPHY,
without the firmware it can not be probed on the MDIO bus.
The clock names in the sysctrl.c file have to be changed because the
clocks are now used by a different driver. This should be cleaned up and
a real common clock driver should provide the clocks instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6xxx can have external PHYs attached to certain ports and those
PHYs could even be on different MDIO bus than the one within the switch.
This patch makes sure that ports with such PHYs are configured correctly
according to the information provided by the PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Built-in PHY ports are still being polled, avoid generating spurious
and duplicate events which the PHY library resolves through polling
anyways.
Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "pause" variable is only initialized on BCM5301x.
Fixes: 5e004460f8 ("net: dsa: b53: Add helper to set link parameters")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case B53_SRAB is enabled, but not B53_SERDES, we can get the
following linking error:
ERROR: "b53_serdes_init" [drivers/net/dsa/b53/b53_srab.ko] undefined!
We also need to ifdef the body of b53_srab_serdes_map_lane() since it
would not be used when B53_SERDES is disabled and that would produce a
warning.
Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Northstar Plus SerDes which is accessed through a
special page of the switch. Since this is something that most people
probably will not want to use, make it a configurable option with a
default on ARCH_BCM_NSP where it is the most useful currently.
The SerDes supports both SGMII and 1000baseX modes for both lanes, and
2500baseX for one of the lanes, and is internally looking like a
seemingly standard MII PHY, except for the few bits that got repurposed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for PHYLINK, things are reasonably straight forward since we
do not yet support SerDes interfaces, that leaves us with just
MLO_AN_PHY and MLO_AN_FIXED to deal with.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the logic from b53_adjust_link() responsible for overriding a
given port's link, speed, duplex and pause settings and make two helper
functions to set the port's configuration and the port's link settings.
We will make use of both, as separate functions while adding PHYLINK
support next.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the SRAB driver to manage per-port interrupts. Since we cannot
sleep during b53_io_ops, schedule a workqueue whenever we get a port
specific interrupt. We will later make use of this to call back into
PHYLINK when there is e.g: a link state change.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switches expose individual interrupt line(s) for port specific
event(s), allow configuring these interrupts at an appropriate time
during port_enable/disable callbacks where all port specific resources
are known to be set-up and ready for use.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6352 family has one SERDES interface, which can be used by either
port 4 or port 5. Add interrupt support for the SERDES interface, and
report when the link status changes.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After changing to the needed page, actually write the value to the
register!
Fixes: 09cb7dfd3f ("net: dsa: mv88e6xxx: describe PHY page and SerDes")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SRAB driver is the default way to communicate with the integrated
switch on iProc platforms and the MMAP driver is the way to communicate
with the integrated switch on DSL BCM63xx and CM BCM33xx.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some boards the interrupt can be shared between multiple devices.
For example on Turris Mox the interrupt is shared between all switches.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz9477 is superset of ksz9xx series, driver just works
out of the box for ksz9897 chip with this patch.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We added a new error path, but we need to drop the lock before we return.
Fixes: 2d2e1dd299 ("net: dsa: mv88e6xxx: Cache the port cmode")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are trying to test if these flags are set but there are some && vs &
typos.
Fixes: efd1ba6af9 ("net: dsa: mv88e6xxx: Add SERDES phydev_mac_change up for 6390")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The totally undocumented IO mode needs to be set to enumerator
0 to enable port 4 also known as WAN in most configurations,
for ordinary traffic. The 3 bits in the register come up as
010 after reset, but need to be set to 000.
The Realtek source code contains a name for these bits, but
no explanation of what the 8 different IO modes may be.
Set it to zero for the time being and drop a comment so
people know what is going on if they run into trouble. This
"mode zero" works fine with the D-Link DIR-685 with
RTL8366RB.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port changes CMODE, the SERDES interface being used can change.
Disable interrupts for the old SERDES interface, and enable interrupts
on the new.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink wants to know when the MAC layers notices a change in the
link. For the 6390 family, this is a change in the SERDES state.
Add interrupt support for the SERDES interface used to implement
SGMII/1000Base-X/2500Base-X. This is currently limited to ports 9 and
10. Support for the 10G SERDES and other ports will be added later,
building on this basic framework.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
An up coming change will register interrupts for individual switch
ports, using the mv88e6xxx_port as the interrupt context information.
Add members to the mv88e6xxx_port structure so we can link it back to
the mv88e6xxx_chip member the port belongs to and the port number of
the port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 family has a number of SERDES interfaces per port. When the
cmode changes, eg 1000Base-X to XAUI, the SERDES interface in use will
also change. Power down the old SERDES interface and power up the new
SERDES interface.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ports CMODE indicates the type of link between the MAC and the
PHY. It is used often in the SERDES code. Rather than read it each
time, cache its value.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 has three different SERDES interface types. 2500Base-X is
implemented by the SGMII/1000Base-X SERDES. So power on/off the
correct SERDES.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for accessing SERDES registers of the 6390 family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a need to add more functions manipulating the SERDES
interfaces. Cleanup the namespace.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 has two SERDES interfaces, used by ports 9 and 10. The 6390X
has eight SERDES interfaces. These allow ports 9 and 10 to do 10G. Or
if lower speeds are used, some of the SERDES interfaces can be used by
ports 2-8 for 1000Base-X.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 family has 8 SERDES lanes. What ports use these lanes depends
on how ports 9 and 10 are configured. If 9 and 10 does not make use of
a line, one of the lower ports can use it.
Add a function to return the lane a port is using, if any, and simplify
the code to power up/down the lane.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rudimentary phylink support to mv88e6xxx.
TODO:
- needs to call phylink_mac_change() when the port link comes up/goes down.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6185 can enable/disable 802.3z pause be setting the MyPause bit in
the port status register. Add an op to support this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Broadcom Omega SoC internal ethernet switch
to the b53 srab driver in the DSA framework.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow propagating ethtool::rxnfc programming to the CPU/management port
such that it is possible for such a CPU to perform e.g: Wake-on-LAN
using filters configured by the switch. We need a tiny bit of
cooperation between the switch drivers which is able to do the full flow
matching, whereas the CPU/management port might not. The CPU/management
driver needs to return -EOPNOTSUPP to indicate an non critical error,
any other error code otherwise.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we are in Wake-on-LAN, we operate with the host sofware not running
a network stack, so we want to the switch to flood packets in order to
cause a system wake-up when matching specific filters (unicast or
multicast). This was not necessary before since we supported Magic
Packet which are targeting a broadcast MAC address which the switch
already floods.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ds->enabled_port_mask only contains a bitmask of user-facing enabled
ports, we also need to allow programming CFP rules that target CPU ports
(e.g: ports 5 and 8).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
Version 1 of the patch adding SERDES support to the 88E6141/6341
correctly added the ops to the 88E6141/6341. However, by the time
version 3 was committed, the ops had moved to the 88E6085/6175. Put
them back where they belong.
Fixes: 5bafeb6e7e ("net: dsa: mv88e6xxx: 88E6141/6341 SERDES support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MODULE_LICENSE() to net/dsa/realtek.o to fix build warning message.
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/dsa/realtek.o
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
free_irq() waits until all handlers for this IRQ have completed. As the
relevant handler (mv88e6xxx_g1_irq_thread_fn()) takes the chip's reg_lock
it might never return if the thread calling free_irq() holds this lock.
For the same reason kthread_cancel_delayed_work_sync() in the polling case
must not hold this lock.
Also first free the irq (or stop the worker respectively) such that
mv88e6xxx_g1_irq_thread_work() isn't called any more before the irq
mappings are dropped in mv88e6xxx_g1_irq_free_common() to prevent the
worker thread to call handle_nested_irq(0) which results in a NULL-pointer
exception.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
For slow processors using bit-banging MDIO, 20ms can be too short a
timeout when waiting for the transmit timestamp to become
available. Double it to 40ms.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the 6352 and newer switches, the PTP Ethertype defaults to
ETH_P_1588. Hence it was not explicitly set. The 6165 however defaults
to 0. So explicitly set the EtherType.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6165 family supports a more restricted version of hardware time
stamps. Only L2 PTP is supported. All ports have to use the same
EtherType, and transport spec configuration. PTP can only be
enabled/disabled globally, not per port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6165 only supports layer L2 PTP, where as the more modern devices
also support UDP and UDPv6, i.e. L4. Abstract the supported receive
filters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6165 family does not have per port PTP control registers. Also, it
places the timestamp data in different registers. Abstract the current
implementation of 6352 compatible PTP devices so that 6165 can be
added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6165 family has its global clock in the PTP global
registers. It does not support any form of PTP events. Add a function
to read the clock, fill in an ops structure, and register it with the
two members of the family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6165 PTP registers are all in AVB bank F, unlike newer
generations which spread them over AVB bank E and F. Implement AVB ops
for the MV88E6165 which hides this difference.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6165 family supports PTP, but its registers use a different
layout to the currently supported devices. Abstract accessing the PTP
registers into a set of ops, so making space for a second
implementation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_DSA_BCM_SF2 does not need to depend on CONFIG_OF anymore since we have
stubs when that option is disabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/dsa/rtl8366.c: In function ‘rtl8366_reset_vlan’:
drivers/net/dsa/rtl8366.c:234:25: warning: unused variable ‘vlan4k’ [-Wunused-variable]
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a driver core for the Realtek SMI chips and a
subdriver for the RTL8366RB. I just added this chip simply
because it is all I can test.
The code is a massaged variant of the code that has been
sitting out-of-tree in OpenWRT for years in the absence of
a proper switch subsystem. This creates a DSA driver for it.
I have tried to credit the original authors wherever
possible.
The main changes I've done from the OpenWRT code:
- Added an IRQ chip inside the RTL8366RB switch to demux and
handle the line state IRQs.
- Distributed the phy handling out to the PHY driver.
- Added some RTL8366RB code that was missing in the driver at
the time, such as setting up "green ethernet" with a funny
jam table and forcing MAC5 (the CPU port) into 1 GBit.
- Select jam table and add the default jam table from the
vendor driver, also for ASIC "version 0" if need be.
- Do not store jam tables in the device tree, store them
in the driver.
- Pick in the "initvals" jam tables from OpenWRT's driver
and make those get selected per compatible for the
whole system. It's apparently about electrical settings
for this system and whatnot, not really configuration
from device tree.
- Implemented LED control: beware of bugs because there are
no LEDs on the device I am using!
We do not implement custom DSA tags. This is explained in
a comment in the driver as well: this "tagging protocol" is
not simply a few extra bytes tagged on to the ethernet
frame as DSA is used to. Instead, enabling the CPU tags
will make the switch start talking Realtek RRCP internally.
For example a simple ping will make this kind of packets
appear inside the switch:
0000 ff ff ff ff ff ff bc ae c5 6b a8 3d 88 99 a2 00
0010 08 06 00 01 08 00 06 04 00 01 bc ae c5 6b a8 3d
0020 a9 fe 01 01 00 00 00 00 00 00 a9 fe 01 02 00 00
0030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
As you can see a custom "8899" tagged packet using the
protocol 0xa2. Norm RRCP appears to always have this
protocol set to 0x01 according to OpenRRCP. You can also
see that this is not a ping packet at all, instead the
switch is starting to talk network management issues
with the CPU port.
So for now custom "tagging" is disabled.
This was tested on the D-Link DIR-685 with initramfs and
OpenWRT userspaces and works fine on all the LAN ports
(lan0 .. lan3). The WAN port is yet not working.
Cc: Antti Seppälä <a.seppala@gmail.com>
Cc: Roman Yeryomin <roman@advem.lv>
Cc: Colin Leitner <colin.leitner@googlemail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
drivers/net/dsa/vitesse-vsc73xx.c:1054:6: warning:
symbol 'vsc73xx_get_strings' was not declared. Should it be static?
drivers/net/dsa/vitesse-vsc73xx.c:1113:5: warning:
symbol 'vsc73xx_get_sset_count' was not declared. Should it be static?
drivers/net/dsa/vitesse-vsc73xx.c:1122:6: warning:
symbol 'vsc73xx_get_ethtool_stats' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_err error message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable 'off' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'off' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a DSA driver for:
Vitesse VSC7385 SparX-G5 5-port Integrated Gigabit Ethernet Switch
Vitesse VSC7388 SparX-G8 8-port Integrated Gigabit Ethernet Switch
Vitesse VSC7395 SparX-G5e 5+1-port Integrated Gigabit Ethernet Switch
Vitesse VSC7398 SparX-G8e 8-port Integrated Gigabit Ethernet Switch
These switches have a built-in 8051 CPU and can download and execute
firmware in this CPU. They can also be configured to use an external
CPU handling the switch in a memory-mapped manner by connecting to
that external CPU's memory bus.
This driver (currently) only takes control of the switch chip over
SPI and configures it to route packages around when connected to a
CPU port. The chip has embedded PHYs and VLAN support so we model it
using DSA as a best fit so we can easily add VLAN support and maybe
later also exploit the internal frame header to get more direct
control over the switch.
The four built-in GPIO lines are exposed using a standard GPIO chip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Broadcom Cygnus SoC, the brcm tag needs to be inserted
in between the mac address and the ether type (should use
'DSA_PROTO_TAG_BRCM') for the packets sent to the internal
b53 switch.
Since the Cygnus was added with the BCM58XX device id and the
BCM58XX uses 'DSA_PROTO_TAG_BRCM_PREPEND', the data path is
broken, due to the incorrect brcm tag location.
Add a new b53 device id (BCM583XX) for Cygnus family to fix the
issue. Add the new device id to the BCM58XX family as Cygnus
is similar to the BCM58XX in most other functionalities.
Fixes: 1160603960 ("net: dsa: b53: Support prepended Broadcom tags")
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reported-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the BCM5389 switch connected through MDIO.
Signed-off-by: Damien Thébault <damien.thebault@vitec.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it explicit that either device tree is used or platform data. If
neither is available, abort the probe.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 877b7cb0b6 ("net: dsa: mv88e6xxx: Add minimal platform_data support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove redundant debug prints from phy_read/write since we can trace those
calls through trace events. Enhance dynamic debug prints to print arguments
which helps figuring how what is going on at the driver level with higher level
configuration interfaces.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix warning reported by checkpatch.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the GPLv2 license boilerplate with the SPDX license identifier.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement adjust_link function that allows to overwrite default CPU port
setting using fixed-link device tree subnode.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default autonegotiation is enabled to configure MAC on all ports.
For the CPU port autonegotiation can not be used so we need to set
some sensible defaults manually.
This patch forces the default setting of the CPU port to 1000Mbps/full
duplex which is the chip maximum capability.
Also correct size of the bit field used to configure link speed.
Fixes: 6b93fb4648 ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is brought up/down do not enable/disable only the TXMAC
but the RXMAC as well. This is essential for the CPU port to work.
Fixes: 6b93fb4648 ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the four-port variant of the Qualcomm QCA833x switch.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
In mv88e6xxx_probe(), ("np" or "pdata") might be an invariant
but GCC can't see that, therefore:
drivers/net/dsa/mv88e6xxx/chip.c: In function ‘mv88e6xxx_probe’:
drivers/net/dsa/mv88e6xxx/chip.c:4420:13: warning: ‘compat_info’ may be used uninitialized in this function [-Wmaybe-uninitialized]
chip->info = compat_info;
Actually, it should have warned on the "if (!compat_info)" test, but
whatever.
Explicitly initialize to NULL in the variable declaration to
deal with this.
Fixes: 877b7cb0b6 ("net: dsa: mv88e6xxx: Add minimal platform_data support")
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the size of the EEPROM to the platform data, so it can also be
instantiated by a platform device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all the world uses device tree. Some parts of the world still use
platform devices and platform data. Add basic support for probing a
Marvell switch via platform data.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An IRQ domain will work without an OF node. It is not possible to
reference interrupts via a phandle, but C code can still use
irq_find_mapping() to get an interrupt from the domain.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers have the following pattern:
if (np)
of_mdiobus_register()
else
mdiobus_register()
which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was possible to delete only one half of an IPv6, which would leave
the second half still programmed and possibly in use. Instead of
checking for the unused bitmap, we need to check the unique bitmap, and
refuse any deletion that does not match that criteria. We also need to
move that check from bcm_sf2_cfp_rule_del_one() into its caller:
bcm_sf2_cfp_rule_del() otherwise we would not be able to delete second
halves anymore that would not pass the first test.
Fixes: ba0696c22e ("net: dsa: bcm_sf2: Add support for IPv6 CFP rules")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had several issues that would make the programming of IPv6 rules both
inconsistent and error prone:
- the chain ID that we would be asking the hardware to put in the
packet's Broadcom tag would be off by one, it would return one of the
two indexes, but not the one user-space specified
- when an user specified a particular location to insert a CFP rule at,
we would not be returning the same index, which would be confusing if
nothing else
- finally, like IPv4, it would be possible to overflow the last entry by
re-programming it
Fix this by swapping the usage of rule_index[0] and rule_index[1] where
relevant in order to return a consistent and correct user-space
experience.
Fixes: ba0696c22e ("net: dsa: bcm_sf2: Add support for IPv6 CFP rules")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we let the kernel pick up a rule location with RX_CLS_LOC_ANY, we
would be able to overwrite the last rules because of a number of issues.
The IPv4 code path would not be checking that rule_index is within
bounds, and it would also only be allowed to pick up rules from range
0..126 instead of the full 0..127 range. This would lead us to allow
overwriting the last rule when we let the kernel pick-up the location.
Fixes: 3306145866 ("net: dsa: bcm_sf2: Move IPv4 CFP processing to specific functions")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the Global 1 specific setup function only setup the statistics
unit, kill it in favor of a mv88e6xxx_stats_setup function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Marvell switch families except 88E6390 have direct registers in
Global 1 for IEEE and IP priorities override mapping. The 88E6390 uses
indirect tables instead.
Add .ieee_pri_map and .ip_pri_map ops to distinct that and call them
from a mv88e6xxx_pri_setup helper. Only non-6390 are concerned ATM.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6390 model has its histogram mode bits moved in the
Global 1 Control 2 register. Use the previously introduced
mv88e6xxx_g1_ctl2_mask helper to set them.
At the same time complete the documentation of the said register.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have converted the bcm_sf2 driver to implement PHYLINK MAC
operations, we can remove the PHYLIB callbacks: adjust_link() and
fixed_link_update() which are no longer called by DSA.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rudimentary phylink support to mv88e6xxx. This allows the driver
using user ports with fixed links to keep operating normally. User ports
with normal PHYs are not affected since the switch automatically manages
their link parameters. User facing ports which use a SFP/SFF with a
non-fixed link mode might require a call to phylink_mac_change() to
operate properly.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[Andrew: fixed link setting after adding link polling]
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[florian: expand commit message]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the bcm_sf2 driver implement phylink_mac_ops since it needs to
support a wide variety of network interfaces: internal & external MDIO
PHYs, fixed PHYs, MoCA with MMIO link status.
A large amount of what needs to be done already exists under
bcm_sf2_sw_adjust_link() so we are essentially breaking this down into
the necessary operation for PHYLINK to work: mac_config, mac_link_up,
mac_link_down and validate. We can now entirely get rid of most of what
fixed_link_update() provided because only the link information is actually
necessary. We still have to force DUPLEX_FULL for legacy Device Tree bindings
that did not specify that before.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RMU mode bits moved a lot within the Global Control 2 register of
the Marvell switch families. Add an .rmu_disable op to support at least
3 known alternatives.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Marvell switches supported by mv88e6xxx have to set their device
number in the Global Control 2 register. Extract this in a read then
write function, called from the device mapping setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the 88E6185 family has bits 15:12 Cascade Port bits in the Global
Control 2 register. Hence inconsistent values are actually written in
this register for other families.
Add a .set_cascade_port operation to isolate the 88E6185 case, and call
it from the device mapping setup function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E6141/6341 switches (also known as Topaz) have 1 SGMII lane,
which can be configured the same way as the SERDES lane on 88E6390.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the mv88e6xxx switches have the PHYs at address 0, 1, 2, ...
The 6341 however has the PHYs at 0x10, 0x11, 0x12. Add a parameter to
the info structure for this base address.
Testing of 6f88284f3b ("net: dsa: mv88e6xxx: Add MDIO interrupts for
internal PHYs") was performed on the 6341. So it works only on the
6341. Use this base information to correctly set the interrupt.
Fixes: 6f88284f3b ("net: dsa: mv88e6xxx: Add MDIO interrupts for internal PHYs")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remaining values written to the Switch Management Register in the
mv88e6xxx_g2_setup function are specific to 88E6352 and older, and are
the default values anyway.
Thus remove completely this function. The mv88e6xxx driver no more
contains setup code to access arbitrary Global 2 registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Device Mapping setup out of the specific Global 2 code,
into the top level device setup function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the trunking setup out of Global 2 specific setup into the top
level mv88e6xxx_setup function.
Note that the 88E6390 family calls this LAG instead of Trunk and
supports 32 possible ID routing vectors, with LAG ID bit 4 being placed
in Global 2 register 0x1D...
We don't need Trunk (or LAG) IDs for the moment, thus keep it simple.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
U64_MAX is well defined now while the UINT64_MAX is not, so we fall
back to drivers' own definition as below:
#ifndef UINT64_MAX
#define UINT64_MAX (u64)(~((u64)0))
#endif
I believe this is in one phy driver then copied and pasted to other phy
drivers.
Replace the UINT64_MAX with U64_MAX to clean up the source code.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We just return the same statistics through ethtool_get_stats() and
ethtool_get_phy_stats() for simplicity since this is just a mock-up driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the b53 driver to return PHY statistics when the CPU port used is
different than 5, 7 or 8, because those are typically PHY-less on most
devices. This is useful for debugging link problems between the switch
and an external host when using a non standard CPU port number (e.g: 4).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we largely assumed that we were interested in ETH_SS_STATS
type of strings for all ethtool operations, this is about to change with
the introduction of additional string sets, e.g: ETH_SS_PHY_STATS.
Update all functions to take an appropriate stringset argument and act
on it when it is different than ETH_SS_STATS for now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA stack passes received PTP frames to this driver via
mv88e6xxx_port_rxtstamp() for deferred delivery. The driver then
queues the frame and kicks the worker thread. The work callback reads
out the latched receive time stamp and then works through the queue,
delivering any non-matching frames without a time stamp.
If a new frame arrives after the worker thread has read out the time
stamp register but enters the queue before the worker finishes
processing the queue, that frame will be delivered without a time
stamp.
This patch fixes the race by moving the queue onto a list on the stack
before reading out the latched time stamp value.
Fixes: c6fe0ad2c3 ("net: dsa: mv88e6xxx: add rx/tx timestamping support")
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We would be passing 0 instead of NULL as the rsp argument to
mt7530_fdb_cmd(), fix that.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sparse complains about the following warnings:
drivers/net/dsa/b53/b53_mmap.c:33:31: warning: incorrect type in
initializer (different address spaces)
drivers/net/dsa/b53/b53_mmap.c:33:31: expected unsigned char
[noderef] [usertype] <asn:2>*regs
drivers/net/dsa/b53/b53_mmap.c:33:31: got void *priv
and indeed, while what we are doing is functional, we are dereferencing
a void * pointer into a void __iomem * which is not great. Just use the
defined b53_mmap_priv structure which holds our register base and use
that.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflicts in drivers/net/ethernet/mellanox/mlx5/core/en_rep.c,
we had some overlapping changes:
1) In 'net' MLX5E_PARAMS_LOG_{SQ,RQ}_SIZE -->
MLX5E_REP_PARAMS_LOG_{SQ,RQ}_SIZE
2) In 'net-next' params->log_rq_size is renamed to be
params->log_rq_mtu_frames.
3) In 'net-next' params->hard_mtu is added.
Signed-off-by: David S. Miller <davem@davemloft.net>
VTU miss violations can happen under normal conditions. Don't spam the
kernel log, downgrade the output to debug level only. The statistics
counter will indicate it is happening, if anybody not debugging is
interested.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Count the numbers of various ATU and VTU violation statistics and
return them as part of the ethtool -S statistics.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's required to create a modules.alias via MODULE_DEVICE_TABLE helper
for the OF platform driver. Otherwise, module autoloading cannot work.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
MODULE_ALIAS exports information to allow the module to be auto-loaded at
boot for the drivers registered using legacy platform registration.
However, currently the driver is always used by DT-only platform,
MODULE_ALIAS is redundant and should be removed properly.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When free'ing the polled IRQs, call the common irq free code.
Otherwise the interrupts are left registered, and when we come to load
the driver a second time, we get an Opps.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
By calling request_threaded_irq() with the flag IRQF_TRIGGER_FALLING
we override the trigger mode provided in device tree. And the
interrupt is actually active low, which is what all the current device
tree descriptions use.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a functional dependency on the FIXED_PHY MDIO bus because we register
fixed PHY devices "the old way" which only works if the code that does this has
had a chance to run before the fixed MDIO bus is probed. Make sure we account
for that and have dsa_loop_bdinfo.o be either built-in or modular depending on
whether CONFIG_FIXED_PHY reflects that too.
Fixes: 98cd1552ea ("net: dsa: Mock-up driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes the respective line in /proc/interrupts from
49: x x mv88e6xxx-g1 7 Edge mv88e6xxx-g1
to
49: x x mv88e6xxx-g1 7 Edge mv88e6xxx-g2
which makes more sense.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch name is emitted in the kernel log, so having the right name
there is nice.
Fixes: 1558727a1c ("net: dsa: mv88e6xxx: Add support for ethernet switch 88E6141")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When registering an MDIO bus, it is possible to pass an array of
interrupts, one per address on the bus. phylib will then associate the
interrupt to the PHY device, if no other interrupt is provided.
Some of the global2 interrupts are PHY interrupts. Place them into the
MDIO bus structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add to the info structure the number of internal PHYs, if they generate
interrupts. Some of the older generations of switches have internal
PHYs, but no interrupt registers. In this case, set the count to zero.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent change to polling for interrupts, it is important that
the number of global 1 interrupts is listed. Without it, the driver
requests an interrupt domain for zero interrupts, which returns
EINVAL, and the probe fails.
Add two missing entries.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can hit the register lock not held assertion with the following path:
[ 34.170631] mv88e6085 0.1:00: Switch registers lock not held!
[ 34.176510] CPU: 0 PID: 950 Comm: ethtool Not tainted 4.16.0-rc4 #143
[ 34.182985] Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
[ 34.189519] Backtrace:
[ 34.192033] [<8010c4b4>] (dump_backtrace) from [<8010c788>] (show_stack+0x20/0x24)
[ 34.199680] r6:9f5dc010 r5:00000011 r4:9f5dc010 r3:00000000
[ 34.205434] [<8010c768>] (show_stack) from [<80679d38>] (dump_stack+0x24/0x28)
[ 34.212719] [<80679d14>] (dump_stack) from [<804844a8>] (mv88e6xxx_read+0x70/0x7c)
[ 34.220376] [<80484438>] (mv88e6xxx_read) from [<804870dc>] (mv88e6xxx_port_get_cmode+0x34/0x4c)
[ 34.229257] r5:a09cd128 r4:9ee31d07
[ 34.232880] [<804870a8>] (mv88e6xxx_port_get_cmode) from [<80487e6c>] (mv88e6352_port_has_serdes+0x24/0x64)
[ 34.242690] r4:9f5dc010
[ 34.245309] [<80487e48>] (mv88e6352_port_has_serdes) from [<804880b8>] (mv88e6352_serdes_get_stats+0x28/0x12c)
[ 34.255389] r4:00000001
[ 34.257973] [<80488090>] (mv88e6352_serdes_get_stats) from [<804811e8>] (mv88e6xxx_get_ethtool_stats+0xb0/0xc0)
[ 34.268156] r10:00000000 r9:00000000 r8:00000000 r7:a09cd020 r6:00000001 r5:9f5dc01c
[ 34.276052] r4:9f5dc010
[ 34.278631] [<80481138>] (mv88e6xxx_get_ethtool_stats) from [<8064f740>] (dsa_slave_get_ethtool_stats+0xbc/0xc4)
mv88e6xxx_get_ethtool_stats() calls mv88e6xxx_get_stats() which calls both
chip->info->ops->stats_get_stats(), which holds the register lock, and
chip->info->ops->serdes_get_stats() which does not. Have
chip->info->ops->serdes_get_stats() be running with the register lock held to
avoid such assertions.
Fixes: 436fe17d27 ("net: dsa: mv88e6xxx: Allow the SERDES interfaces to have statistics")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle polled interrupts correctly when loading the module.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 294d711ee8 ("net: dsa: mv88e6xxx: Poll when no interrupt defined")
Signed-off-by: David S. Miller <davem@davemloft.net>
Call the common irq free function, rather than going recursive and
blowing away the stack, followed by the machine.
Fixes: 294d711ee8 ("net: dsa: mv88e6xxx: Poll when no interrupt defined")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/dsa/mv88e6xxx/serdes.c:66:9-10: WARNING: return of 0/1 in function 'mv88e6352_port_has_serdes' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Fixes: eb755c3f6b ("net: dsa: mv88e6xxx: Add helper to determining if port has SERDES")
CC: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our statistics strings are allocated at initialization without being
bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using
memcpy() which would create out of bounds accesses, this was flagged by
KASAN. Replace this with strlcpy() to make sure we are bound the source
buffer size and we also always NUL-terminate strings.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading the SERDES statistics of the mv88e8352, using
the standard ethtool -S option. The SERDES interface can be mapped to
either port 4 or 5, so only return statistics on those ports, if the
SERDES interface is in use.
The counters are reset on read, so need to be accumulated. Add a per
port structure to hold the stats counters. The 6352 only has a single
SERDES interface and so only one port will using the newly added
array. However the 6390 family has as many SERDES interfaces as ports,
each with statistics counters. Also, PTP has a number of counters per
port which will also need accumulating.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the existing code. This helper will be used for SERDES
statistics.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When gettting the number of statistics, the strings and the actual
statistics, call the SERDES ops if implemented. This means the stats
code needs to return the number of strings/stats they have placed into
the data, so that the SERDES strings/stats can follow on.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, there has been no need to hold the reg mutex while getting
the count of statistics, or the strings, because the hardware was not
accessed. When adding support for SERDES statistics, it is necessary
to access the hardware, to determine if a port is using the SERDES
interface. So add mutex lock/unlocks.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By passing the port, we allow different ports to have different
statistics. This is useful since some ports have SERDES interfaces
with their own statistic counters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all boards have the interrupt output from the switch connected to
a GPIO line. In such cases, phylib has to poll the internal PHYs,
rather than receive an interrupt when there is a change in the link
state. phylib polls once per second, and per PHY reads around 4
words. With a switch typically having 4 internal PHYs, this means 16
MDIO transactions per second.
Rather than performing this phylib level polling, have the driver poll
the interrupt status register. If the status register indicates an
interrupt condition processing of interrupts in the same way as if a
GPIO was used.
Polling 10 times a second places less load on the MDIO bus. But rather
than taking on average 0.5s to detect a link change, it takes less
than 0.05s. Additionally, other interrupts, such as the watchdog, ATU
and VTU violations will be reported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declaring a static function in a header leads to a warning every
time that header gets included without the function being used:
In file included from drivers/net/dsa/mv88e6xxx/chip.c:42:
drivers/net/dsa/mv88e6xxx/ptp.h:92:13: error: 'mv88e6xxx_hwtstamp_work' defined but not used [-Werror=unused-function]
static long mv88e6xxx_hwtstamp_work(struct ptp_clock_info *ptp)
In file included from drivers/net/dsa/mv88e6xxx/chip.c:38:
drivers/net/dsa/mv88e6xxx/global2.h:355:12: error: 'mv88e6xxx_g2_wait' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_wait(struct mv88e6xxx_chip *chip, int reg, u16 mask)
^~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.h:350:12: error: 'mv88e6xxx_g2_update' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_update(struct mv88e6xxx_chip *chip, int reg, u16 update)
^~~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.h:345:12: error: 'mv88e6xxx_g2_write' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_write(struct mv88e6xxx_chip *chip, int reg, u16 val)
^~~~~~~~~~~~~~~~~~
drivers/net/dsa/mv88e6xxx/global2.h:340:12: error: 'mv88e6xxx_g2_read' defined but not used [-Werror=unused-function]
static int mv88e6xxx_g2_read(struct mv88e6xxx_chip *chip, int reg, u16 *val)
This marks all such functions in dsa inline to make sure we don't warn
about them.
Fixes: c6fe0ad2c3 ("net: dsa: mv88e6xxx: add rx/tx timestamping support")
Fixes: 0d632c3d6f ("net: dsa: mv88e6xxx: add accessors for PTP/TAI registers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MV88E6352 and later switches support GPIO control through the "Scratch
& Misc" global2 register. Two of the pins controlled this way on the
mv88e6390 family are the external MDIO pins. They can either by used
as part of the MII interface for port 0, GPIOs, or MDIO. Add a
function to configure them for MDIO, if possible, and call it when
registering the external MDIO bus.
Suggested-by: Russell King <rmk@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
_port_ is already known to be a valid index in the callers [1]. So
these checks are unnecessary.
[1] https://lkml.org/lkml/2018/2/16/469
Addresses-Coverity-ID: 1465287
Addresses-Coverity-ID: 1465291
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The shifting of timehi by 16 bits to the left will be promoted to
a 32 bit signed int and then sign-extended to an u64. If the top bit
of timehi is set then all then all the upper bits of ns end up as also
being set because of the sign-extension. Fix this by making timehi and
timelo u64. Also move the declaration of ns.
Detected by CoverityScan, CID#1465288 ("Unintended sign extension")
Fixes: c6fe0ad2c3 ("net: dsa: mv88e6xxx: add rx/tx timestamping support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP code needs low latency access to the PTP hardware timestamps.
Reading all the ATU entries in one go adds a lot of latency to the PTP
code. So take and release the reg_lock mutex for each individual MAC
address in the ATU, allowing the PTP thread jump in between.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean
Rasmus Villemoes
Nikita Yushchenko
David S. Miller
Linus Torvalds
YueHaibing
Thomas Gleixner
Colin Ian King
Wang Hai
Nathan Chancellor
Hauke Mehrtens
Vivien Didelot
Andrew Lunn
Dan Carpenter
Gustavo A. R. Silva
Heiner Kallweit
Christian Lamparter
Florian Fainelli
Tristram Ha
Maxime Chevallier
Marek Behún
Russell King
Vinod Koul
John David Anglin
Arun Parameswaran
Miquel Raynal
Pablo Neira Ayuso
Linus Walleij
Greg Ungerer
Johan Hovold
Kangjie Lu
Vivien Didelot
Marek Vasut
Anderson Luiz Alves
kbuild test robot
Wolfram Sang
Arnd Bergmann
zhong jiang
Wei Yongjun
Lad, Prabhakar
Randy Dunlap
Uwe Kleine-König
Kees Cook
Damien Thébault
Michal Vokáč
Jisheng Zhang
Richard Cochran
Sean Wang