- Support 64-bit timestamps
MTD changes:
Core changes:
- Support sub-partitions
- Clarify mtd_oob_ops documentation
- Make Kconfig formatting consistent
- Fix potential overflows in mtdchar_{write,read}()
- Fallback to ->_{read,write}() when ->_{read,write}_oob() is missing
and no OOB data were requested
- Remove VLA usage in the bch lib
Driver changes:
- Use mtd_device_register() instead of mtd_device_parse_register()
where applicable
- Use proper printk format to print physical addresses in the
solutionengine driver
- Add missing mtd_set_of_node() call in the powernv driver
- Remove unneeded variables in a few drivers
- Plug the TRX part parser to the DT partition parsers logic
- Check ioremap_cache() return code in the gpio-addr-flash driver
- Stop using VMLINUX_SYMBOL_STR() in gen_probe.c
SPI NOR changes:
Core changes:
- Apply reset hacks only when reset is explicitly marked as broken in
the DT
Driver changes:
- Minor cleanup/fixes in the m25p80 driver
- Release flash_np in the nxp-spifi driver
- Add suspend/resume hooks to the atmel-quadspi driver
- Include gpio/consumer.h instead of gpio.h in the atmel-quadspi
driver
- Use %pK instead of %p in the stm32-quadspi driver
- Improve timeout handling in the cadence-quadspi driver
- Use mtd_device_register() instead of mtd_device_parse_register()
in the intel-spi driver
NAND changes:
Core changes:
- Add the SPI-NAND framework.
- Create a helper to find the best ECC configuration.
- Create NAND controller operations.
- Allocate dynamically ONFI parameters structure.
- Add defines for ONFI version bits.
- Add manufacturer fixup for ONFI parameter page.
- Add an option to specify NAND chip as a boot device.
- Add Reed-Solomon error correction algorithm.
- Better name for the controller structure.
- Remove unused caller_is_module() definition.
- Make subop helpers return unsigned values.
- Expose _notsupp() helpers for raw page accessors.
- Add default values for dynamic timings.
- Kill the chip->scan_bbt() hook.
- Rename nand_default_bbt() into nand_create_bbt().
- Start to clean the nand_chip structure.
- Remove stale prototype from rawnand.h.
Raw NAND controllers drivers changes:
- Qcom: structuring cleanup.
- Denali: use core helper to find the best ECC configuration.
- Possible build of almost all drivers by adding a dependency on
COMPILE_TEST for almost all of them in Kconfig, implies various
fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even
changes in sparc64 and ia64 architectures.
- Clean the ->probe() functions error path of a lot of drivers.
- Migrate all drivers to use nand_scan() instead of
nand_scan_ident()/nand_scan_tail() pair.
- Use mtd_device_register() where applicable to simplify the code.
- Marvell:
* Handle on-die ECC.
* Better clocks handling.
* Remove bogus comment.
* Add suspend and resume support.
- Tegra: add NAND controller driver.
- Atmel:
* Add module param to avoid using dma.
* Drop Wenyou Yang from MAINTAINERS.
- Denali: optimize timings handling.
- FSMC: Stop using chip->read_buf().
- FSL:
* Switch to SPDX license tag identifiers.
* Fix qualifiers in MXC init functions.
Raw NAND chip drivers changes:
- Micron:
* Add fixup for ONFI revision.
* Update ecc_stats.corrected.
* Make ECC activation stateful.
* Avoid enabling/disabling ECC when it can't be disabled.
* Get the actual number of bitflips.
* Allow forced on-die ECC.
* Support 8/512 on-die ECC.
* Fix on-die ECC detection logic.
- Hynix:
* Fix decoding the OOB size on H27UCG8T2BTR.
* Use ->exec_op() in hynix_nand_reg_write_op().
-----BEGIN PGP SIGNATURE-----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=yIkF
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.19' of git://git.infradead.org/linux-mtd
Pull mtd updates from Boris Brezillon:
"JFFS2 changes:
- Support 64-bit timestamps
MTD core changes:
- Support sub-partitions
- Clarify mtd_oob_ops documentation
- Make Kconfig formatting consistent
- Fix potential overflows in mtdchar_{write,read}()
- Fallback to ->_{read,write}() when ->_{read,write}_oob() is missing
and no OOB data were requested
- Remove VLA usage in the bch lib
MTD driver changes:
- Use mtd_device_register() instead of mtd_device_parse_register()
where applicable
- Use proper printk format to print physical addresses in the
solutionengine driver
- Add missing mtd_set_of_node() call in the powernv driver
- Remove unneeded variables in a few drivers
- Plug the TRX part parser to the DT partition parsers logic
- Check ioremap_cache() return code in the gpio-addr-flash driver
- Stop using VMLINUX_SYMBOL_STR() in gen_probe.c
SPI NOR core changes:
- Apply reset hacks only when reset is explicitly marked as broken in
the DT
SPI NOR driver changes:
- Minor cleanup/fixes in the m25p80 driver
- Release flash_np in the nxp-spifi driver
- Add suspend/resume hooks to the atmel-quadspi driver
- Include gpio/consumer.h instead of gpio.h in the atmel-quadspi
driver
- Use %pK instead of %p in the stm32-quadspi driver
- Improve timeout handling in the cadence-quadspi driver
- Use mtd_device_register() instead of mtd_device_parse_register() in
the intel-spi driver
NAND core changes:
- Add the SPI-NAND framework.
- Create a helper to find the best ECC configuration.
- Create NAND controller operations.
- Allocate dynamically ONFI parameters structure.
- Add defines for ONFI version bits.
- Add manufacturer fixup for ONFI parameter page.
- Add an option to specify NAND chip as a boot device.
- Add Reed-Solomon error correction algorithm.
- Better name for the controller structure.
- Remove unused caller_is_module() definition.
- Make subop helpers return unsigned values.
- Expose _notsupp() helpers for raw page accessors.
- Add default values for dynamic timings.
- Kill the chip->scan_bbt() hook.
- Rename nand_default_bbt() into nand_create_bbt().
- Start to clean the nand_chip structure.
- Remove stale prototype from rawnand.h.
Raw NAND controllers drivers changes:
- Qcom: structuring cleanup.
- Denali: use core helper to find the best ECC configuration.
- Possible build of almost all drivers by adding a dependency on
COMPILE_TEST for almost all of them in Kconfig, implies various
fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even
changes in sparc64 and ia64 architectures.
- Clean the ->probe() functions error path of a lot of drivers.
- Migrate all drivers to use nand_scan() instead of
nand_scan_ident()/nand_scan_tail() pair.
- Use mtd_device_register() where applicable to simplify the code.
- Marvell:
* Handle on-die ECC.
* Better clocks handling.
* Remove bogus comment.
* Add suspend and resume support.
- Tegra: add NAND controller driver.
- Atmel:
* Add module param to avoid using dma.
* Drop Wenyou Yang from MAINTAINERS.
- Denali: optimize timings handling.
- FSMC: Stop using chip->read_buf().
- FSL:
* Switch to SPDX license tag identifiers.
* Fix qualifiers in MXC init functions.
Raw NAND chip drivers changes:
- Micron:
* Add fixup for ONFI revision.
* Update ecc_stats.corrected.
* Make ECC activation stateful.
* Avoid enabling/disabling ECC when it can't be disabled.
* Get the actual number of bitflips.
* Allow forced on-die ECC.
* Support 8/512 on-die ECC.
* Fix on-die ECC detection logic.
- Hynix:
* Fix decoding the OOB size on H27UCG8T2BTR.
* Use ->exec_op() in hynix_nand_reg_write_op()"
* tag 'mtd/for-4.19' of git://git.infradead.org/linux-mtd: (188 commits)
mtd: rawnand: atmel: Select GENERIC_ALLOCATOR
MAINTAINERS: drop Wenyou Yang from Atmel NAND driver support
mtd: rawnand: allocate dynamically ONFI parameters during detection
mtd: spi-nor: only apply reset hacks to broken hardware
mtd: spi-nor: cadence-quadspi: fix timeout handling
mtd: spi-nor: atmel-quadspi: Include gpio/consumer.h instead of gpio.h
mtd: spi-nor: intel-spi: use mtd_device_register()
mtd: spi-nor: stm32-quadspi: replace "%p" with "%pK"
mtd: spi-nor: atmel-quadspi: add suspend/resume hooks
mtd: rawnand: allocate model parameter dynamically
mtd: rawnand: do not export nand_scan_[ident|tail]() anymore
mtd: rawnand: txx9ndfmc: convert driver to nand_scan()
mtd: rawnand: txx9ndfmc: clarify ECC parameters assignation
mtd: rawnand: tegra: convert driver to nand_scan()
mtd: rawnand: jz4740: convert driver to nand_scan()
mtd: rawnand: jz4740: group nand_scan_{ident, tail} calls
mtd: rawnand: jz4740: fix probe function error path
mtd: rawnand: docg4: convert driver to nand_scan()
mtd: rawnand: do not execute nand_scan_ident() if maxchips is zero
mtd: rawnand: atmel: convert driver to nand_scan()
...
Having the zload address at 0x8060.0000 means the size of the
uncompressed kernel cannot be bigger than around 6 MiB, as it is
deflated at address 0x8001.0000.
This limit is too small; a kernel with some built-in drivers and things
like debugfs enabled will already be over 6 MiB in size, and so will
fail to extract properly.
To fix this, we bump the zload address from 0x8060.0000 to 0x8100.0000.
This is fine, as all the boards featuring Ingenic JZ SoCs have at least
32 MiB of RAM, and use u-boot or compatible bootloaders which won't
hardcode the load address but read it from the uImage's header.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19787/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
This way we will be able to compile the jz4740_nand driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This work is now performed by the watchdog driver directly.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-mips@linux-mips.org
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: James Hogan <jhogan@kernel.org>
Also remove the watchdog platform_device from platform.c, since it
wasn't used anywhere anyway.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: linux-mips@linux-mips.org
Cc: linux-watchdog@vger.kernel.org
Cc: devicetree@vger.kernel.org
[jhogan@kernel.org: Drop jz4740_wdt_device declaration from header]
Signed-off-by: James Hogan <jhogan@kernel.org>
This converts the bit-banged GPIO SPI driver to looking up and
using GPIO descriptors to get a handle on GPIO lines for SCK,
MOSI, MISO and all CS lines.
All existing board files are converted in one go to keep it all
consistent. With these conversions I rarely find any interrim
steps that makes any sense.
Device tree probing and GPIO handling should work like before
also after this patch.
For board files, we stop using controller data to pass the GPIO
line for chip select, instead we pass this as a GPIO descriptor
lookup like everything else.
In some s3c24xx machines the names of the SPI devices were set to
"spi-gpio" rather than "spi_gpio" which can never have worked, I
fixed it working (I guess) as part of this patch set. Sometimes
I wonder how this code got upstream in the first place, it
obviously is not tested.
mach-s3c64xx/mach-smartq.c has the same problem and additionally
defines the *same* GPIO line for MOSI and MISO which is not going
to be accepted by gpiolib. As the lines were number 1,2,2 I assumed
it was a typo and use lines 1,2,3. A comment gives awat that line 0
is chip select though no actual SPI device is provided for the LCD
supposed to be on this bit-banged SPI bus. I left it intact instead
of just deleting the bus though.
Kill off board file code that try to initialize the SPI lines
to the same values that they will later be set by the spi_gpio
driver anyways. Given the huge number of weird things in these
board files I do not think this code is very tested or put in
with much afterthought anyways.
In order to assert that we do not get performance regressions on
this crucial bing-banged driver, a ran a script like this dumping the
Ilitek ILI9322 regmap 10000 times (it has no caching obviously) on
an otherwise idle system in two iterations before and after the
patches:
#!/bin/sh
for run in `seq 10000`
do
cat /debug/regmap/spi0.0/registers > /dev/null
done
Before the patch:
time test.sh
real 3m 41.03s
user 0m 29.41s
sys 3m 7.22s
time test.sh
real 3m 44.24s
user 0m 32.31s
sys 3m 7.60s
After the patch:
time test.sh
real 3m 41.32s
user 0m 28.92s
sys 3m 8.08s
time test.sh
real 3m 39.92s
user 0m 30.20s
sys 3m 5.56s
So any performance differences seems to be in the error margin.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GCW Zero (http://www.gcw-zero.com) is a retro-gaming focused
handheld game console, successfully kickstarted in ~2012, running Linux.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18490/
Signed-off-by: James Hogan <jhogan@kernel.org>
Provide just enough bits (clocks, clocksource, uart) to allow a kernel
to boot on the JZ4770 SoC to a initramfs userspace.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Reviewed-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18487/
Signed-off-by: James Hogan <jhogan@kernel.org>
Previously, the mips_machtype variable was always initialized
to MACH_INGENIC_JZ4740 even if running on different SoCs.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18486/
Signed-off-by: James Hogan <jhogan@kernel.org>
jz4740_init_cmdline appends all arguments from argv (in fw_arg1) to
arcs_cmdline, up to argc (in fw_arg0). The common code in
fw_init_cmdline will do the exact same thing when run on a system where
fw_arg0 isn't a pointer to kseg0 (it'll also set _fw_envp but we don't
use it). Remove the custom implementation & use the generic code.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Reviewed-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18484/
Signed-off-by: James Hogan <jhogan@kernel.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the drivers for the various hardware elements of the jz4740 SoC have
been modified to use the pinctrl framework for their pin configuration
needs.
As such, this platform code is now unused and can be deleted.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We set the pin configuration for the jz4740-nand, jz4740-mmc,
jz4740-fb, jz4740-pwm and jz4740-uart drivers.
This will permit those drivers to be cleaned out of the custom GPIO code
that they currently use.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation for making the clockevents core NTP correction aware,
all clockevent device drivers must set ->min_delta_ticks and
->max_delta_ticks rather than ->min_delta_ns and ->max_delta_ns: a
clockevent device's rate is going to change dynamically and thus, the
ratio of ns to ticks ceases to stay invariant.
Make the MIPS arch's clockevent drivers initialize these fields properly.
This patch alone doesn't introduce any change in functionality as the
clockevents core still looks exclusively at the (untouched) ->min_delta_ns
and ->max_delta_ns. As soon as this has changed, a followup patch will
purge the initialization of ->min_delta_ns and ->max_delta_ns from these
drivers.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Keguang Zhang <keguang.zhang@gmail.com>
Cc: John Crispin <john@phrozen.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Historically a lot of these existed because we did not have
a distinction between what was modular code and what was providing
support to modules via EXPORT_SYMBOL and friends. That changed
when we forked out support for the latter into the export.h file.
This means we should be able to reduce the usage of module.h
in code that is obj-y Makefile or bool Kconfig. In the case of
some code where it is modular, we can extend that to also include
files that are building basic support functionality but not related
to loading or registering the final module; such files also have
no need whatsoever for module.h
The advantage in removing such instances is that module.h itself
sources about 15 other headers; adding significantly to what we feed
cpp, and it can obscure what headers we are effectively using.
Since module.h might have been the implicit source for init.h
(for __init) and for export.h (for EXPORT_SYMBOL) we consider each
instance for the presence of either and replace/add as needed.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Build coverage of all the mips defconfigs revealed the module.h
header was masking a couple of implicit include instances, so
we add the appropriate headers there.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: David Daney <david.daney@cavium.com>
Cc: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "Steven J. Hill" <steven.hill@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15131/
[james.hogan@imgtec.com: Preserve sort order where it already exists]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
This commit removes two things:
- The platform_device that corresponds to the RTC driver, since we now
probe this driver from devicetree;
- The platform power-off code, since all the jz4740-based platforms are
now using the jz4740-rtc driver as the system power controller.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since we already have a devicetree node for the jz4740-rtc driver, we
don't have to probe it from platform code.
Besides, using the jz4740-rtc driver as the power controller for the
qi_lb60 platform allows us to remove the jz4740 platform power-off code,
since this is the only jz4740-based board upstream.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After patch "of/platform: Add common method to populate default bus",
it is possible for arch code to remove unnecessary callers of
of_platform_populate with default match table.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alban Bedel <albeu@free.fr>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Rob Herring <robh@kernel.org>
First cycle with Boris as NAND maintainer! Many (most) bullets stolen from him.
Generic:
* Migrated NAND LED trigger to be a generic MTD trigger
NAND:
* Introduction of the "ECC algorithm" concept, to avoid overloading the ECC
mode field too much more
* Replaced the nand_ecclayout infrastructure with something a little more
flexible (finally!) and future proof
* Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some of
this into their own tree as well
* Prepare the sunxi NAND driver to receive DMA support
* Handle bitflips in erased pages on GPMI revisions that do not support
this in hardware.
SPI NOR:
* Start using the spi_flash_read() API for SPI drivers that support it (i.e.,
SPI drivers with special memory-mapped flash modes)
And other small scattered improvments.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=J6KN
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"First cycle with Boris as NAND maintainer! Many (most) bullets stolen
from him.
Generic:
- Migrated NAND LED trigger to be a generic MTD trigger
NAND:
- Introduction of the "ECC algorithm" concept, to avoid overloading
the ECC mode field too much more
- Replaced the nand_ecclayout infrastructure with something a little
more flexible (finally!) and future proof
- Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some
of this into their own tree as well
- Prepare the sunxi NAND driver to receive DMA support
- Handle bitflips in erased pages on GPMI revisions that do not
support this in hardware.
SPI NOR:
- Start using the spi_flash_read() API for SPI drivers that support
it (i.e., SPI drivers with special memory-mapped flash modes)
And other small scattered improvments"
* tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd: (155 commits)
mtd: spi-nor: support GigaDevice gd25lq64c
mtd: nand_bch: fix spelling of "probably"
mtd: brcmnand: respect ECC algorithm set by NAND subsystem
gpmi-nand: Handle ECC Errors in erased pages
Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
mtd: nand: add support for "nand-ecc-algo" DT property
mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
mtd: nand: read ECC algorithm from the new field
mtd: nand: fsmc: validate ECC setup by checking algorithm directly
mtd: nand: set ECC algorithm to Hamming on fallback
staging: mt29f_spinand: set ECC algorithm explicitly
CRIS v32: nand: set ECC algorithm explicitly
mtd: nand: atmel: set ECC algorithm explicitly
mtd: nand: davinci: set ECC algorithm explicitly
mtd: nand: bf5xx: set ECC algorithm explicitly
mtd: nand: omap2: Fix high memory dma prefetch transfer
mtd: nand: omap2: Start dma request before enabling prefetch
mtd: nandsim: add __init attribute
mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
...
The DT fragment will select the ohci-platform driver, since that can
handle the JZ4740 OHCI just fine. While I don't have a JZ4740-based
board with anything connected to the USB host controller, I did test
the generic OHCI driver successfully on a JZ4770-based board.
The device is disabled by default; boards that want to use it can
override the "status" property. The mass-production Qi LB60 boards
don't use the USB host controller.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13104/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
AVT2 was a prototype board of which about 5 were made, none of which
are in use anymore.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13103/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implementing the mtd_ooblayout_ops interface is the new way of exposing
ECC/OOB layout to MTD users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: linux-mips@linux-mips.org
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is fallout from commit 832f5dacfa ("MIPS: Remove all the uses of
custom gpio.h").
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
The board code never sets up a leds-pwm device, so including the header
is not necessary.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11262/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Associate the PWM with the pwm-beeper device using a PWM lookup table.
This will eventually allow the legacy function calls to pwm_request() to
be removed from all consumer drivers.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11261/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Somehow the wrong version of the patch to remove the use of custom
gpio.h on mips has been merged. This patch add the missing fixes for a
build error on jz4740 because linux/gpio.h doesn't provide any machine
specfics definitions anymore.
Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11089/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Currently CONFIG_ARCH_HAVE_CUSTOM_GPIO_H is defined for all MIPS
machines, and each machine type provides its own gpio.h. However
only a handful really implement the GPIO API, most just forward
everythings to gpiolib.
The Alchemy machine is notable as it provides a system to allow
implementing the GPIO API at the board level. But it is not used by
any board currently supported, so it can also be removed.
For most machine types we can just remove the custom gpio.h, as well
as the custom wrappers if some exists. Some of the code found in
the wrappers must be moved to the respective GPIO driver.
A few more fixes are need in some drivers as they rely on linux/gpio.h
to provides some machine specific definitions, or used asm/gpio.h
instead of linux/gpio.h for the gpio API.
Signed-off-by: Alban Bedel <albeu@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Daniel Walter <dwalter@google.com>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Buesch <m@bues.ch>
Cc: abdoulaye berthe <berthe.ab@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ide@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10828/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Migrate jz4740 driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linaro-kernel@lists.linaro.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Patchwork: https://patchwork.linux-mips.org/patch/10601/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: linux-mips@linux-mips.org
Cc: LKML <linux-kernel@vger.kernel.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Patchwork: https://patchwork.linux-mips.org/patch/10695/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Support the Ingenic JZ4780 SoC using the existing code under
arch/mips/jz4740 now that it has been generalised sufficiently.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Andreas Herrmann <andreas.herrmann@caviumnetworks.com>
Patchwork: https://patchwork.linux-mips.org/patch/10164/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the serial support from arch/mips/jz4740 & make use of the new
Ingenic SoC UART driver. This is done for both regular & early console
output.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Apelete Seketeli <apelete@seketeli.net>
Cc: Alexandre Courbot <gnurou@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10160/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allow a devicetree to specify the memory present in the system rather
than probing it from the memory controller. This both saves the probing
for systems where the amount of memory is fixed, and will simplify the
bringup of later Ingenic SoCs where the memory controller register
layout differs.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10163/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The only thing remaining in arch/mips/jz4740/clock.h is declarations of
the jz4740_clock_{suspend,resume} functions. Move these to
arch/mips/include/asm/mach-jz4740/clock.h for consistency with similar
functions, and remove the redundant arch/mips/jz4740/clock.h header.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10156/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The jz4740-cgu driver already has access to the CGU, so it makes sense
to move the few remaining accesses to the CGU from arch/mips/jz4740
there too. Move the jz4740_clock_{suspend,resume} functions there for
such consistency. The arch/mips/jz4740/clock.c file now contains nothing
more of use & so is removed.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10158/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The jz4740-cgu driver already has access to the CGU, so it makes sense
to move the few remaining accesses to the CGU from arch/mips/jz4740
there too. Move the jz4740_clock_udc_{dis,en}able_auto_suspend functions
there for such consistency.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10154/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The jz4740-cgu driver already has access to the CGU, so it makes sense
to move the few remaining accesses to the CGU from arch/mips/jz4740
there too. Move jz4740_clock_set_wait_mode for such consistency.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10153/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Migrate the JZ4740 & the qi_lb60 board to use common clock framework
via the new Ingenic SoC CGU driver. Note that the JZ4740-specific
debugfs code is removed since common clock framework provides its own
debug capabilities.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Co-authored-by: Paul Cercueil <paul@crapouillou.net>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Fabian Frederick <fabf@skynet.be>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10151/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace uses of the jz4740_clock_bdata struct with calls to clk_get_rate
for the appropriate clock. This is in preparation for migrating the
clocks towards common clock framework & devicetree.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: Apelete Seketeli <apelete@seketeli.net>
Patchwork: https://patchwork.linux-mips.org/patch/10149/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Call jz4740_clock_init before any uses of jz4740_clock_bdata occur. This
is in preparation for replacing uses of that struct with calls to
clk_get_rate, which will allow the clocks to be migrated towards common
clock framework & devicetree.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-mips@linux-mips.org
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10148/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the driver for Ingenic SoC interrupt controllers into
drivers/irqchip where it belongs.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10147/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allow the interrupt controllers of the JZ4770, JZ4775 & JZ4780 SoCs to
be probed via devicetree, supporting the 64 interrupts they provide.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10155/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rename the functions including jz4740 in their names to be more generic
in preparation for supporting further SoCs, and for moving this
interrupt controller code to drivers/irqchip.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Patchwork: https://patchwork.linux-mips.org/patch/10146/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Read the base address of the SoC interrupt controller from the device
tree rather than relying upon the JZ4740_INTC_BASE_ADDR macro, in order
to remove the dependency on the asm/mach-jz4740/base.h header.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10145/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On newer Ingenic SoCs the interrupt controller supports more than 32
interrupts, which it does by duplicating the registers at intervals
of 0x20 bytes within its address space. Add support for an arbitrary
number of interrupts using multiple generic chips, and provide the
number of chips to register from the interrupt controller probe
function.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10141/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Avoid the need for the global variable jz_intc_base by introducing a
struct ingenic_intc_data and passing it around as the IRQ handler data.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Brian Norris <computersforpeace@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/10144/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Torvalds
Paul Cercueil
Boris Brezillon
Linus Walleij
Paul Burton
Greg Kroah-Hartman
Nicolai Stange
Paul Gortmaker
Thomas Gleixner
Masahiro Yamada
Kefeng Wang
Maarten ter Huurne
Boris Brezillon
Ralf Baechle
Thierry Reding
Alban Bedel
Viresh Kumar
Paul Burton