Whenever the PAN (P2P) context is active, it
has timers in the uCode that prevent sleep,
so scanning can't be out of channel for more
than the beacon interval programmed into the
device.
Before this patch, a full scan including any
passive channels when P2P was active would
stall forever because it wouldn't find time
to execute the passive requests (for default
beacon intervals of 100 TU.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Fix multiple bugs in event tracing:
1) If you enable uCode tracing with the device down,
it will still attempt to access the device and
continuously log "MAC is in deep sleep!" errors.
Fix this by only starting logging when the device
is actually alive.
2) Now you can set the flag when the device is down,
but logging doesn't happen when you bring it up.
To fix that, start logging when the device comes
alive. This means we don't log before -- we could
do that but I don't need it right now.
3) For some reason we read the error instead of the
event log -- use the right pointer.
4) Optimise SRAM reading of event log header.
5) Fix reading write pointer == capacity, which can
happen due to racy SRAM access
6) Most importantly: fix an error where we would try
to read WAY too many events (like 2^32-300) when
we read the wrap counter before it is updated by
the uCode -- this does happen in practice and will
cause the driver to hang the machine.
7) Finally, change the timer to 10ms instead of 100ms
as 100ms is too slow to capture all data with a
normal event log and with 100ms the log will wrap
multiple times before we have a chance to read it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
While configuring the broadcast key in the hardware, in
multi-BSS environment, BSSes other than first were
incorrectly configured with the MAC address of first
BSS. Fixing it with correct MAC addresses.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, when we are on an IBSS network with no active station,
we would scan for other BSSID, even if fixed_bssid is on, due to
a bug in ibss.c, where fixed_channel would be checked instead of
fixed_bssid. This would trigger useless scans where scan results
would not be used anyway.
This patch also reverts commit 39d02a7d90,
which assumed that the ifibss->fixed_channel check was legitimate
to disable single-channel scans. IBSS single-channel scan should
now be fixed.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sta might be in psm against the ap (e.g. because
this was the before a hw restart), so we explicitly
send a null packet in order to make sure it'll
sync against the ap (and get out of psm).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a pointer so it should be NULL instead of zero. Sparse
complains about this stuff:
net/nfc/nci/core.c:447:37: warning: Using plain integer as NULL pointer
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables user to check beacon interval, DTIM period, short slot
time and short preamble information using "iw dev mlan0 link" command
when station is in connected state.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass mwifiex_private pointer directly to wmm_add_buf_txqueue()
instead of passing adapter and then deriving priv again in
mwifiex_get_priv_by_id(). This reduces a 'for' loop in TX path.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This seems to be only needed as workaround for hardware problem on
PCI devices.
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zero all other bits than RESET_CSR and RESET_BBP when want to do the
reset, that the vendor driver behaviour.
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can receive frames just after firmware load with current code, so
disable DMA just after firmware is loaded, not before.
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ralink USB driver initialize H2M_INT_SRC to 0 after firmware load, and
never touch this register later. It is not touched at all by Ralink PCI
driver.
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix new kernel-doc warnings:
Warning(include/net/cfg80211.h:1165): No description found for parameter 'channel_type'
Warning(include/net/cfg80211.h:2090): No description found for parameter 'probe_resp_offload'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements a simple way of reducing the
output power of the device by a configurable upper
limit.
Requested-by: Harshal Chhaya <harshal@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A mesh node that joins the mesh network is by default a forwarding entity. This patch allows
the mesh node to set as non-forwarding entity. Whenever dot11MeshForwarding is set to 0, the
mesh node can prevent itself from forwarding the traffic which is not destined to him.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems that -Wshadow is no longer default in
sparse runs, but let's fix the warnings anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems that -Wshadow is no longer default in
sparse runs, but let's fix the warnings anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to the previous beacon filtering patch,
make CQM RSSI support depend on the flags that
the driver set for virtual interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to firmware limitations, we may not be able to
support beacon filtering on all virtual interfaces.
To allow this in mac80211, introduce per-interface
driver capability flags that the driver sets when
an interface is added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avoids this:
CC [M] drivers/net/wireless/orinoco/orinoco_usb.o
drivers/net/wireless/orinoco/orinoco_usb.c:1759:13: warning: ‘version’ defined but not used
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avoids this:
CC [M] drivers/net/wireless/ath/ath5k/base.o
drivers/net/wireless/ath/ath5k/base.c: In function ‘__check_no_hw_rfkill_switch’:
drivers/net/wireless/ath/ath5k/base.c:85:1: warning: return from incompatible pointer type
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interrupt comes in, we read the reason
bits and collect them into "trans_pcie->inta".
This happens with the spinlock held. However,
there's a bug resetting this variable -- that
happens after the spinlock has been released.
This means that it is possible for interrupts
to be missed if the reset happens after some
other interrupt reasons were already added to
the variable.
I found this by code inspection, looking for a
reason that we sometimes see random commands
time out. It seems possible that this causes
such behaviour, but I can't say for sure right
now since it happens extremely infrequently on
my test systems.
Cc: stable@vger.kernel.org [3.2]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__ieee80211_recalc_idle() iterates through the vifs,
sets bss_conf.idle = true if they are disconnected,
and increases "count" if they are not (which later
gets evaluated in order to determine whether the
device is idle).
However, the loop doesn't set bss_conf.idle = false
(along with increasing "count"), causing the device
idle state and the vif idle state to get out of sync
in some cases.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 13c40c5 ("mac80211: Add HT operation modes for IBSS") broke
ibss operation by mistakenly removing the local->oper_channel
update (causing ibss to start on the wrong channel). fix it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Skip group keys configuration in hardware in order to make IBSS RSN work.
Keys will be managed using software.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the ability to select between multiple targets in NCI.
If only one target is found, it will be auto-activated.
If more than one target is found, then DISCOVER_NTF will be
generated for each target, and the host should select one by
calling DISCOVER_SELECT_CMD. Then, the target will be activated.
If the activation fails, GENERIC_ERROR_NTF is generated.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The NFC core layer should not set the target_idx.
Instead, the driver layer (e.g. NCI, PN533) should set the
target_idx, so that it will be able to identify the target
when its I/F (e.g. activate_target) is called.
This is required in order to support multiple targets.
Note that currently supported drivers (PN533 and NCI) don't
use the target_idx in their implementation.
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make a clear separation between NCI states and flags.
This is required in order to support more NCI states (e.g.
for multiple targets support).
Signed-off-by: Ilan Elias <ilane@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of a node re-joining the cell the sta_info structure belonging to it is
first destroyed and then reinserted. In this way its internal state is reset.
The joining operation is recognised thank the Auth frame being received.
This operation is helpful in case of a node being rebooted that is joining the
ad-hoc cell again, before its purge timeout on other nodes expires.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In IBSS mode, whenever a new station is added a 2-way authentication challenge
is performed. Actually this event can be used to recognise a new station joining
the cell even if its sta_info entry is already in the list.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Free sk_buff if nfcwilink_send fails.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Download TI NFC init script during nfcwilink open operation,
after the NFC channel is registered with TI shared transport.
TI NFC init script is written in BTS format.
First, read the chip version via a special vendor specific command.
Second, we request the relevant BTS file from the user space, and
then send the BTS commands to the chip.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add endian annotations to TI nfcwilink driver.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add NCI data exchange timer to catch timeouts,
and call the data exchange callback with an error.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems exceedingly unlikely that we'll ever
support swapping rate control algorithms at
runtime, so remove the unused refcounting code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yogesh's patch to destroy aggregation sessions when
stations are destroyed was needed, but unnecessarily
complex. Clean up this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export new attributes sensb_res for tech B and sensf_res
for tech F in the target info (returned as a response to
NFC_CMD_GET_TARGET).
The max size of the attributes nfcid1, sensb_res and sensf_res
is exported to user space though include/linux/nfc.
Signed-off-by: Ilan Elias <ilane@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert printks to pr_<level>
Prefix logging with pr_fmt.
Use ##__VA_ARGS__ in some WL_ logging macros.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert a couple of pr_debug/print_hex_dump to
the standard utility.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use pr_debug to allow dynamic debugging to work.
Move an #endif to allow brcmf_dbg_hex_dump
to be outside the #if/#endif block.
Move a const char* declaration to be inside a
pr_debug so the function doesn't need a #if/#endif
block.
Don't use temporaries in debugging functions so
the code can be optimized away.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce the number of #ifdef DEBUG uses by
adding a dbg_hex_dump routine which has the
appropriate #ifdef DEBUG test.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current CONFIG_BRCMDBG flag when enabled does not
necessarily enable proper pr_debug output when
DEBUG is not also enabled.
Remove BCMDBG define and just use DEBUG instead.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable group keys programming when using IBSS RSN. Keys will be managed using
software. In this way IBSS RSN can correctly work.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the early days, this was a quite useful software
feature for testing different regdomains and chain
configurations without adding debugfs cruft into
the driver. Nowadays, the driver's phy code seems
to be stable and there's no need for it anymore.
Therefore I decided to removed altogether.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg
Wey-Yi Guy
Yogesh Ashok Powar
Nicolas Cavallari
Eliad Peller
Dan Carpenter
Amitkumar Karwar
Avinash Patil
Stanislaw Gruszka
Randy Dunlap
Christian Lamparter
Chun-Yeow Yeoh
John W. Linville
Antonio Quartulli
Ilan Elias
Joe Perches