The DPS310 is a temperature and pressure sensor. It can be accessed over
i2c and SPI, but this driver only supports polling over i2c.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds minimal driver for the Honeywell Amplified Basic
Pressure sensors series. Sensors are pretty simple but are
available in many variants:
- psi/mbar/kPa output,
- analog/i2c/spi,
- gage/differential measurement,
- different measure ranges etc.
Refer to datasheets for more details:
http://sensing.honeywell.com/honeywell-sensing-basic-board-mount-pressure-sensors-abp-series-datasheet-323005128-c-en.pdfhttp://sensing.honeywell.com/index.php%3Fci_id%3D45841
Driver internals:
- i2c only. measure request is done by the SMBUS QUICK cmd, so if the i2c
bus doesn't support it, it is required to send a dummy byte to trigger
measurement,
- since iio sysfs expects kilopascals, mbar-variants are treated as their
respective kPa-s, hence i2c id-table has doubled entries in one line:
{ "abp060mg", ABP006KG }, { "abp006kg", ABP006KG },
- psi-variants have prescaled values in config,
- no temperature reads yet.
Work remained:
- optional temperature channel,
- SPI support,
- DT binding.
Changes since v1:
- mutex is now locked in read_raw(),
- corrected error codes,
- fixed coding style issues,
- renamed few defines and functions abp -> abp060mg
(some structs left as they were to keep the sensible meaning).
Signed-off-by: Marcin Malagowski <mrc@bourne.st>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch mimics the SPI functionality found in the misc driver in
drivers/misc/bh085-spi.c to make it possible to reuse the existing
BMP280/BMP180/BMP085 driver with all clients of the other driver.
The adoption is straight-forward since like the other driver, it is
a simple matter of using regmap.
This driver is also so obviously inspired/copied from the old misc
driver in drivers/misc/bmp085.c that I just took the liberty to
add in the authors of the other drivers + self in the core driver
file.
The MISC driver also supports a variant named "BMP181" so include
that here to be complete in comparison to the old driver.
The bus mapping code for SPI was written by Akinobu Mita.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Tested-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This creates a separate BMP280_I2C Kconfig entry that gets selected
by BMP280 for I2C transport. As we currently only support I2C
transport there is not much practical change other than getting
a separate object file (or module) for the I2C driver part. The
old Kconfig symbol BMP280 will still select the stuff we need so
that oldconfig and old defconfigs works fine.
Tested-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This splits the BMP280 driver in three logical parts: the core driver
bmp280-core that only operated on a struct device * and a struct regmap *,
the regmap driver bmp280-regmap that can be shared between I2C and other
transports and the I2C module driver bmp280-i2c.
Cleverly bake all functionality into a single object bmp280.o so that
we still get the same module binary built for the device in the end,
without any fuzz exporting symbols to the left and right.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for HopeRF pressure and temperature sensor.
This device uses two fixed I2C addresses, one for storing
calibration coefficients and another for accessing the ADC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Matt Ranostay <mranostay@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
mpl115 driver currently supports i2c interface (MPL115A2).
There is also SPI version (MPL115A1). The difference between them
is only physical transport so we can easily support both while sharing
most of the code.
Split the driver into a core support module and one module each for I2C
and SPI support.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Support for MS5637 temperature & pressure sensor
Signed-off-by: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for Measurement Specialities MS5611 pressure
and temperature sensor.
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
I2C-controlled sensor with 10-bit pressure and temperature measurement
datasheet: http://cache.freescale.com/files/sensors/doc/data_sheet/MPL3115A2.pdf
v2:
* use devm_iio_device_register()
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added usage id processing for Pressure Sensor. This uses IIO
interfaces for triggered buffer to present data to user
mode. This uses HID sensor framework for registering callback
events from the sensor hub.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
I2C-controlled MEMS sensor with 20-bit pressure measurement (pascal) and
12-bit temperature measurement
driver only exposes basic functionality, see TODO remarks
datasheet: http://cache.freescale.com/files/sensors/doc/data_sheet/MPL3115A2.pdf
v2:
* store 20-bit value in 32-bit buffer element (instead of 24-bit)
* zero buffer to prevent kernel data leak to userspace
* fix mutex unlock in trigger handler (thanks Andi Shyti)
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Keeping Makefile and Kconfig entries in alphabetical order usually works better
than just appending new entries at the end, since it reduces the amount of
conflicts. This patch adds a comment to the IIO Kconfig and Makefile files to
document that the entries should be kept in alphabetical order.
Also reorder those entries which weren't in alphabetical order yet.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds a generic pressure driver for STMicroelectronics
pressure sensors, currently it supports: LPS331AP.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Joel Stanley
Greg Kroah-Hartman
Gwendal Grignou
Marcin Malagowski
Gregor Boirie
Linus Walleij
Marek Vasut
Crestez Dan Leonard
Akinobu Mita
Ludovic Tancerel
Tomasz Duszynski
Vlad Dogaru
Peter Meerwald
Archana Patni
Lars-Peter Clausen
Denis CIOCCA