In some configuration, the PCU may allow us to overclock the GPU.
Check for this case and adjust the max frequency as appropriate. Also
initialize the min/max frequencies to default values as indicated by
hardware.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Some voltage swing/pre-emphasis level use the same value on eDP
Sandybridge, like 400mv_0db and 600mv_0db are with the same value
of (0x0 << 22). So, fix them, and point out the value if it isn't
a supported voltage swing/pre-emphasis level.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
It's required by the specs, but we don't know why. Let's not find out
why.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add an interrupt handler for switching graphics frequencies and handling
PM interrupts. This should allow for increased performance when busy
and lower power consumption when idle.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
v2: Change IS_IRONLAKE to IS_GEN5 to adapt to 2.6.37
This patch adds new functions for use by the drm core:
.get_vblank_timestamp() provides a precise timestamp
for the end of the most recent (or current) vblank
interval of a given crtc, as needed for the DRI2
implementation of the OML_sync_control extension.
It is a thin wrapper around the drm function
drm_calc_vbltimestamp_from_scanoutpos() which does
almost all the work.
.get_scanout_position() provides the current horizontal
and vertical video scanout position and "in vblank"
status of a given crtc, as needed by the drm for use by
drm_calc_vbltimestamp_from_scanoutpos().
The patch modifies the pageflip completion routine
to use these precise vblank timestamps as the timestamps
for pageflip completion events.
This code has been only tested on a HP-Mini Netbook with
Atom processor and Intel 945GME gpu. The codepath for
(IS_G4X(dev) || IS_GEN5(dev) || IS_GEN6(dev)) gpu's
has not been tested so far due to lack of hardware.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add frame buffer compression on Sandybridge. The method is similar to
Ironlake, except that two new registers of type GTTMMADR must be written
with the right fence info.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add the support of memory self-refresh on Sandybridge, which is now
support 3 levels of watermarks and the source of the latency values
for watermarks has changed.
On Sandybridge, the LP0 WM value is not hardcoded any more. All the
latency value is now should be extracted from MCHBAR SSKPD register.
And the MCHBAR base address is changed, too.
For the WM values, if any calculated watermark values is larger than
the maximum value that can be programmed into the associated watermark
register, that watermark must be disabled.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
[ickle: remove duplicate compute routines and fixup for checkpatch]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Once we have read the value out of the GT power well, we need to remove
the FORCE WAKE bit to allow the system to auto-power down.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The bulk of the change is to convert the growing list of rings into an
array so that the relationship between the rings and the semaphore sync
registers can be easily computed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Magic numbers from the specs. This is supposed to allow the PLL some
variance to improve jitter performance and VCO headroom across
manufacturing and environmental variations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The pipe is always set to 8BPC, but here we were leaving whatever
previous bits were set by the BIOS in place.
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
This has proven sufficient to recover from a hang of the GPU using the
gem_bad_blit test while at the KMS console then starting X. When
attempting the same during an X session, the timer doesn't appear to
trigger.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When trying to diagnose mysterious errors on resume, capture the
display register contents as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We only ever used the PRB0, neglecting the secondary ring buffers, and
now with the advent of multiple engines with separate ring buffers we
need to excise the anachronisms from our code (and be explicit about
which ring we mean where). This is doubly important in light of the
FORCEWAKE required to read ring buffer registers on SandyBridge.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Before reading ring register, set FORCE_WAKE bit to prevent GT core
power down to low power state, otherwise we may read stale values.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
[ickle: added a udelay which seemed to do the trick on my SNB]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This is not known to fix any particular bugs we have, but the spec
says to do it, and the BIOS hadn't already set it up on my system.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This holds error state from the main graphics arbiter mainly involving
the DMA engine and address translation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This patch enables the sending of AVI infoframes in
drivers/gpu/drm/i915/intel_hdmi.c.
My receiver currently loses sync when the HDMI output on my computer
(DG45FC motherboard) is switched from 800x600 (the BIOS resolution) to
1920x1080 as part of the boot. Fixable by switching inputs on the receiver
a couple of times.
With this patch, my receiver has not lost sync yet (> 40 tries).
Fourth version, now based on drm-intel-next from:
git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel.git
Two questions still remain:
I'm assuming that the sdvo hardware also stores a header ECC byte in
the MSB of the first dword - is this correct?
Does the SDVOB and SDVOC handling in intel_hdmi_set_avi_infoframe()
look correct?
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Based on an original patch by Zhenyu Wang, this initializes the BLT ring for
SandyBridge and enables support for user execbuffers.
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On Sandybridge, the bit definition for hotplug on SDE has changed, so
update the code to new definition.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30378
Cc: stable@kernel.org
Signed-off-by: Yuanhan Liu <yuanhan.liu@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Needed on Ibex Peak and Cougar Point or the panel won't always come on.
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Enable the panel before adjusting eDP link params, make sure the panel
is idle after powering it on before proceeding with other activity,
delay backlight enable to avoid visible flicker.
Also avoid using VDD per hw team recommendation; it can conflict with
the builtin panel power sequencing logic and lead to panel power
sequencing failures.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
So far only found registers for i830, i845, i865 and one of those has no
effect on i865!
At this moment in time, attempting to reset i8xx is a little
optimistic...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Two macros that use a base address for HWS_PGA were missing, add them.
Also switch the remaining users of *_ACTHD to the ring-base one.
Kill the other ring-specific macros because they're now unused.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[ickle: And silence checkpatch whilst in the vicinity]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Everything is now handled in intel-gtt.h so these defines
are only confusing.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Documentation explicitly mentions that the ring registers are
designed to have the same offsets relative to a base registers.
Use this to fight the code beaurocratic in intel_ringbuffer.c.
No code changes in this patch, just the new definitions.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This looks like a copy-paste remnant from the i810. All the regs
that are actually used are already defined somewhere else in i915_reg.h!
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This ring buffer is used for video decoding/encoding on Sandybridge.
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Ironlake's graphics reset register has to be accessed via the MCHBAR,
rather than via PCI config space, which requires some refactoring.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The graphics domains are listed as GRDOM in the documentation, and the
GDRST PCI config register (0xc0) is only valid on I965 and GM45. Newer
chips (like Sandy Bridge) have a different GDRST.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Use the GMBUS interface rather than direct bit banging to grab the EDID
over DDC (and for other forms of auxiliary communication with external
display controllers). The hope is that this method will be much faster
and more reliable than bit banging for fetching EDIDs from buggy monitors
or through switches, though we still preserve the bit banging as a
fallback in case GMBUS fails.
Based on an original patch by Jesse Barnes.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The purpose is to make the code much easier to read and therefore reduce
the possibility for bugs.
A side effect is that it also makes it much easier for the compiler,
reducing the object size by 4k -- from just a few functions!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Refactor the common code into seperate functions and use the MIN(large,
small) buffer calculation for self-refresh watermarks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Thermal reporting may not be enabled by default on some machines, so
enable the appropriate bits to allow IPS to get the data it needs from
the CPU thermal device.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We don't know how to enable it safely, especially as outputs turn on and
off. When disabling LP1 we also need to make sure LP2 and 3 are already
disabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29173
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29082
Reported-by: Chris Lord <chris@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Make them match the others and add BPP definitions.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If we disable the pipe and the GPU is currently waiting on a scanline
WAIT_FOR_EVENT, the GPU will hang. Fortunately, there is a magic bit
which we can write on i915+ to break this wait after disabling the
pipe.
References:
Bug 29252 - [Arrandale] Hung WAIT_FOR_EVENT when running rss-glx-skyrocket
https://bugs.freedesktop.org/show_bug.cgi?id=29252
Bug 28964 - [i965gm] GPU infinite MI_WAIT_FOR_EVENT while watching video in Totem
https://bugs.freedesktop.org/show_bug.cgi?id=28964
and many others.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Jesse Barnes
Yuanhan Liu
Dave Airlie
Chris Wilson
Eric Anholt
Mario Kleiner
Daniel Vetter
Zou Nan hai
David Härdeman
Yuanhan Liu
Xiang, Haihao
Kenneth Graunke