spuctx_switch_state() warns if ktime goes backwards, but it
sometimes compares an uninitialized value, which showed that
the data was unreliable when we actually saw the warning.
Initialize it to the current time in order to get correct data.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the necessary bits and pieces to powerpc implementation of
ioremap to benefit from caller tracking in /proc/vmallocinfo, at least
for ioremap's done after mem init as the older ones aren't tracked.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Setting G5's cpu frequency transition latency to CPUFREQ_ETERNAL stops
ondemand governor from working. I measured the latency using sched_clock
and haven't seen much higher than 11000ns, so I set this to 12000ns for
my configuration. Possibly other configurations will be different?
Ideally the generic code would be able to measure it in case the platform
does not provide it.
But this simple patch at least makes it throttle again.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On MPC837X CPUs Dual-Role USB isn't always available (for example DR
USB pins can be muxed away to eSDHC).
U-Boot adds status = "disabled" property into the DR USB nodes to
indicate that we must not try to configure or probe Dual-Role USB,
otherwise we'll break eSDHC support on targets with MPC837X CPUs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit a969e76a71 (powerpc: Correct USB
support for GE Fanuc SBC610) introduced a fixup for NEC usb controllers.
This fixup should only run on GEF SBC610 boards.
Fixes Fedora bug #486511.
(https://bugzilla.redhat.com/show_bug.cgi?id=486511)
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To better match the ePAPR specification, device nodes which claim
"simple-bus" compatibility should be probed by default.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
On Wed, 18 Feb 2009 22:18:21 +0100
Giuliano Pochini <pochini@shiny.it> wrote:
Since 2.6.28, /sys/devices/system/cpu/cpu*/online don't exist anymore
on 32-bit PowerMacs due to change in the generic powerpc code.
Signed-off-by: Giuliano Pochini <pochini@shiny.it>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The new firmware release exports further RTC calls. This
patch adds these calls to the QPACE platform setup file.
Signed-off-by: Benjamin Krill <ben@codiert.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are hardware limitations on the number of available MSIs,
which firmware expresses using a property named "ibm,pe-total-#msi".
This property tells us how many MSIs are available for devices below
the point in the PCI tree where we find the property.
For old firmwares which don't have the property, we assume there are
8 MSIs available per "partitionable endpoint" (PE). The PE can be
found using existing EEH code, which uses the methods described in
PAPR. For our purposes we want the parent of the node that's
identified using this method.
When a driver requests n MSIs for a device, we first establish where
the "ibm,pe-total-#msi" property above that device is, or we find the
PE if the property is not found. In both cases we call this node
the "pe_dn".
We then count all non-bridge devices below the pe_dn, to establish
how many devices in total may need MSIs. The quota is then simply the
total available divided by the number of devices, if the request is
less than or equal to the quota, the request is fine and we're done.
If the request is greater than the quota, we try to determine if there
are any "spare" MSIs which we can give to this device. Spare MSIs are
found by looking for other devices which can never use their full
quota, because their "req#msi(-x)" property is less than the quota.
If we find any spare, we divide the spares by the number of devices
that could request more than their quota. This ensures the spare
MSIs are spread evenly amongst all over-quota requestors.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If a driver asks for more MSIs than the devices "req#msi(-x)" property,
we currently return -ENOSPC. This doesn't give the driver any chance to
make a new request with a number that might work.
So if "req#msi(-x)" is less than the request, return its value. To be
100% safe, make sure we return an error if req_msi == 0.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
cbe_cpufreq has a partial dependency on cbe_cpufreq_pmi, which cannot
be easily expressed in Kconfig. This fixes it by introducing an
extra Kconfig symbol CBE_CPUFREQ_PMI_ENABLE. To make the dependency
clearer, turn PPC_PMI into an automatic symbol.
Reported-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The spufs context directory contents definitions are not changed after
initialisation, so we can declare them as const. We can do the same
with the spu coredump reader callbacks too.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, we may setup the MFC for isolated mode initilaisation with
the purge still active. This means that DMAs required to perform the
init do not happen.
This change clears the purge status after doing the purge, so that
the isolated init can proceed.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, spu_handle_mm_fault disregards the 'ret' variable and always
returns -EFAULT on error.
This change refactos spu_handle_mm_fault a little, to return the
ret variable as appropriate. This allows us to combine the error and
sucess paths.
Also, remove the #if-0-ed IS_VALID_EA() check, it has never been
used.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change the PS3 hotplug memory routine ps3_mm_add_memory() from
a core_initcall to a device_initcall.
core_initcall routines run before the powerpc topology_init()
startup routine, which is a subsys_initcall, resulting in
failure of ps3_mm_add_memory() when CONFIG_NUMA=y. When
ps3_mm_add_memory() fails the system will boot with just the
128 MiB of boot memory
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Power ISA 2.06 spec introduces a standard MMU programming model that
is based on the Freescale Book-E MMU programing model. The Freescale
version is pretty backwards compatiable with the ISA 2.06 definition so
we are starting to refactor some of the Freescale code so it can be
easily shared.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This commit adds the setup code for booting Linux on AmigaOne G3SE (G3
only), AmigaOne XE and uA1 (G3/G4) desktop computers. These boards were
sold by Eyetech and are based on MAI Logic's Teron boards and its
Articia S northbridge.
The AmigaOne uses U-boot as firmware, which doesn't support a flattened
device tree yet. The northbridge has some design flaws, which makes it
necessary to use non cacheable memory for DMA operations
(CONFIG_NOT_COHERENT_CACHE) and to avoid setting the coherence (M) flag
for memory pages.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The EEH code disables and enables interrupts during the
device recovery process. This is unnecessary for MSI
and MSI-X interrupts because they are effectively disabled
by the DMA Stopped state when an EEH error occurs. The
current code is also incorrect for MSI-X interrupts. It
doesn't take into account that MSI-X interrupts are tracked
in a different way than LSI/MSI interrupts. This patch
ensures only LSI interrupts are disabled/enabled.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
After the last changes, the mv643xx_eth driver now detects
a spurious interface on port 0. Since only port 1 is actually
connected to a PHY, remove its description.
Signed-off-by: Gabriel Paubert <paubert@iram.es>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we can't allocate the requested number of MSIs, we can still tell the
generic code how many we were able to allocate. That can then be passed
onto the driver, allowing it to request that many in future, and
probably succeeed.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We also need to check that the device isn't using MSI-X in the irq fixup
routine, otherwise we might leave MSI-Xs configured at boot.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Firmware encodes the number of MSI-X requested by a device in a
different property than for MSI. Pull the property name out as a
parameter and share the logic for both cases.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to increment i in the loop that queries what interrupts firmware
gave us, otherwise we'll incorrectly use the first value over and over.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since we never hotplug add an isa bus, we never need to set primary.
Delete this write-only variable.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/platforms/pseries/hotplug-memory.c uses
remove_section_mapping() but doesn't include sparsemem.h which defines
it. This can cause compilation fails for some configs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Taking sizeof the result of sizeof is quite strange and does not seem to be
what is wanted here.
This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression E;
@@
- sizeof (
sizeof (E)
- )
@@
type T;
@@
- sizeof (
sizeof (T)
- )
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Board support for the InterControl Digsy-MTC device based on the MPC5200B SoC.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds board support for the Media5200 platform. Changes are:
- add the media5200 device tree
- add the media5200 platform support code and cascaded interrupt controller
- add media5200 to the build targets.
Note: this patch also includes a minor tweak to the lite5200(b) target
images list to add the .dtb files to the image list.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds IRQ controller support to the MPC5200 General
Purpose Timer (GPT) device driver. With this patch the mpc5200-gpt
driver supports both GPIO and IRQ functions.
The GPT driver was contained within the mpc52xx_gpio.c file, but this
patch moves it out into a new file (mpc52xx_gpt.c) since it has more
than just GPIO functionality now and it was only grouped with the
mpc52xx-gpio drivers as a matter of convenience before. Also, this
driver will most likely get extended again to also provide support
for the timer function.
Implementation note: Alternately, I could have tried to implement
the IRQ support as a separate driver and left the GPIO portion alone.
However, multiple functions of this device (ie. GPIO input+interrupt
controller, or timer+GPIO) can be active at the same time and the
registers are shared so it is safer to contain all functionality
within a single driver.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Rework the mpc5200-pic driver to simplify it and fix up the setting
of desc->status when set_type is called for internal IRQs (so they
are reported as level, not edge). The simplification is due to
splitting off the handling of external IRQs into a separate block
so they don't need to be handled as exceptions in the normal
CRIT, MAIN and PERP paths.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
pr_debug() calls in the 'hot' *_mask(), *_unmask(), *_ack() and
get_irq() makes adding #define DEBUG pretty much useless. Remove
these calls because they completely swamp the output.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
This patch ensures that memory gets properly mapped into the PCI
address space. Without this patch, the memory window BAR is left
at whatever value happened to be loaded into the BAR when Linux
was booted. Without this patch, memory could end up getting mapped
at any of the 1G address boundaries instead of at '0' where Linux
expects it.
Similarly, this patch also ensures that the internally memory mapped
registers (IMMR) are mapped to the correct PCI address range.
Without this patch, PCI appears to work correctly until a PCI
device is inserted which DMAs into memory.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
This patch adds basic support for the 6 GPIO lines found on GE Fanucs SBC310 to the GE Fanuc GPIO driver.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC310 VPX Single Board Computer from GE Fanuc (PowerPC
MPC8641D).
This is the basic board support for GE Fanuc's SBC310, a 3U single board
computer, based on Freescale's MPC8641D.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds pcie nodes to the appropriate dts files, plus adds
some probing code for the boards.
Also, remove of_device_is_avaliable() check from the mpc837x_mds.c
board file, as mpc83xx_add_bridge() has the same check now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Probe the new mdio node added by b31a1d8b. Fix kernel panic problem when
gianfar driver wants to get the of_platform_device of that mdio.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Convert the Warp platform to use the newly merged NDFC driver
- warp.dts changed to work with ndfc
- warp-nand.c no longer needed
- removed obsolete rev A support from cuboot-warp.c
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Fixes compiler warnings:
arch/powerpc/platforms/ps3/mm.c:1205: warning: passing argument 2 of 'ps3_repository_read_mm_info' from incompatible pointer type
arch/powerpc/platforms/ps3/mm.c:1205: warning: passing argument 3 of 'ps3_repository_read_mm_info' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This fixes these compiler warning:
arch/powerpc/platforms/ps3/interrupt.c:109: warning: passing argument 2 of 'clear_bit' from incompatible pointer type
arch/powerpc/platforms/ps3/interrupt.c:130: warning: passing argument 2 of 'set_bit' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Arnd Bergmann
Benjamin Herrenschmidt
Nick Piggin
Anton Vorontsov
Tony Breeds
Grant Likely
Giuliano Pochini
Benjamin Krill
Michael Ellerman
Jeremy Kerr
Madhulika Madishetty
Geoff Levand
Kumar Gala
Gerhard Pircher
Mike Mason
Gabriel Paubert
Milton Miller
Michael Neuling
Julia Lawall
Grzegorz Bernacki
Martyn Welch
Stephen Rothwell
Li Yang
Sean MacLennan