This patch fills in the values for bus speed and width of the
ixgbe_bus_speed and ixgbe_bus_width enums.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some PHYs require that we poll the reset bit and wait for it to clear
before continuing initialization. As such we should add this check to the
end of the ixgbe_reset_phy_generic routine.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently check link reports the link state as down, if at any time
the link had previously gone down since the last time the LINKS
register was read. This does not accurately reflect the function of
the check link call, which should be to return the CURRENT link
state. Code now reads the LINKS registers twice, once to clear the
previous and again to get the current value.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up several issues in ixgbe_identify_sfp_module_generic
including whitespace, redundant code, I2C EEPROM reads without exception
handling, and an if/elseif/else without braces.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Double resets are required for recovery from certain error conditions.
Between resets, it is necessary to stall to allow time for any pending HW
events to complete. We use 1usec since that is what is needed for
ixgbe_disable_pcie_master(). The second reset then clears out any effects
of those events.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The media type was not being set for the 82599 T3 LAN on motherboard. This
change corrects that.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were incorrectly freeing IRQs that we had not requested. This change
corrects that by making certain we only free q_vectors that we have
requested IRQs for.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change cleans up much of the logic related to the hardware semaphores
on the adapters. There were a number of issues with timings that needed to
be addressed.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change just cleans up a few defines in ixgbe_type.h related to wake on LAN.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix Compiler warnings of variables that are initialized but not used.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fix changes the remaining calls to strncpy that have not yet
been changed to use the "sizeof(buf) - 1" syntax rather than just
a number for buffer size.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes the reg_pattern_test so that the test does not fail
on i350 parts.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently there's no warning printed when max_vfs > 7 is specified with
igb and the maximum of 7 is silently enforced. This patch prints a
warning and informs the user of the actions taken.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- Remove the dependency of cxgb4 and cxgb4vf on INET. cxgb3 really
depends on INET, keep it but add it directly to the driver's Kconfig
entry.
- Make the iSCSI drivers cxgb3i and cxgb4i available in the SCSI menu
without requiring any options in the net driver menu to be enabled
first. Add needed selects so the iSCSI drivers can build their
corresponding net drivers.
- Remove CHELSIO_T*_DEPENDS.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Acked-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
of/promtree: allow DT device matching by fixing 'name' brokenness (v5)
x86: OLPC: have prom_early_alloc BUG rather than return NULL
of/flattree: Drop an uninteresting message to pr_debug level
of: Add missing of_address.h to xilinx ehci driver
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Avoid tps6586x burst writes
mfd: Don't suspend WM8994 if the CODEC is not suspended
mfd: Fix DaVinci voice codec device name
mfd: Fix NULL pointer due to non-initialized ucb1x00-ts absinfo
mfd: Fix ASIC3 build with GENERIC_HARDIRQS_NO_DEPRECATED
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] p4-clockmod: print EST-capable warning message only once
[CPUFREQ] fix BUG on cpufreq policy init failure
[CPUFREQ] Fix another notifier leak in powernow-k8.
[CPUFREQ] Missing "unregister_cpu_notifier" in powernow-k8.c
We service 2 queues (kcq1 and kcq2) in cnic_service_bnx2x_bh(). If
the status block index has changed when servicing the kcq2, we must
go back and check kcq1. The latest status block index will be used
to acknowledge the interrupt, and without looping back to check kcq1,
we may miss events on kcq1.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The status block index is used to acknowledge interrupt events and must
be read before checking for the interrupt events, so we need to add rmb()
to guarantee that.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e2f2a93b, "of/promtree: add package-to-path support to pdt"
changed dp->name from using the 'name' property to using
package-to-path. This fixed /proc/device-tree creation by eliminating
conflicts between names (the 'name' property provides names like
'battery', whereas package-to-path provides names like
'/foo/bar/battery@0', which we stripped to 'battery@0'). However, it
also breaks of_device_id table matching.
The fix that we _really_ wanted was to keep dp->name based upon
the name property ('battery'), but based dp->full_name upon
package-to-path ('battery@0'). This patch does just that.
This changes all users (except SPARC) of promtree to use the full
result from package-to-path for full_name, rather than stripping the
directory out. In practice, the strings end up being exactly the
same; this change saves time, code, and memory.
SPARC continues to use the existing build_path_component() code.
v2: combine two patches and revert of_pdt_node_name to original version
v3: use dp->phandle instead of passing around node
v4: warn/bail out for non-sparc archs if pkg2path is not set
v5: split of_pdt_build_full_name into sparc & non-sparc versions
v6: Pass NULL to pkg2path before buf gets assigned.
Drop check for pkg2path hook on each and every node.
v7: Don't BUG() when unable to get the full_path; create a
known-unique name instead.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Build log:
In file included from drivers/usb/host/ehci-hcd.c:1208:
drivers/usb/host/ehci-xilinx-of.c: In function 'ehci_hcd_xilinx_of_probe':
drivers/usb/host/ehci-xilinx-of.c:168: error: implicit declaration of function 'of_address_to_resource'
Signed-off-by: John Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In commit 567aba0b79, the probe address
for tda8290_probe and tda8295_probe was hard-coded to 0x4b, which is the
default i2c address for those devices, but its possible for the device
to be at an alternate address, 0x42, which is the case for the HVR-1950.
If we probe the wrong address, probe fails and we have a non-working
device. We have the actual address passed into the function by way of
i2c_props, we just need to use it. Also fix up some copy/paste comment
issues and streamline debug spew a touch. Verified to restore my
HVR-1950 to full working order.
Special thanks to Ken Bass for reporting the issue in the first place,
and to both he and Gary Buhrmaster for aiding in debugging and analysis
of the problem.
Reported-by: Ken Bass <kbass@kenbass.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's a Realtek combo card reader and IR receiver device with multiple
usb interfaces on it. The mceusb driver is incorrectly grabbing all of
them. This change should make it bind to only interface 2 (patch based
on lsusb output on the linux-media list from Lucian Muresan).
Tested regression-free with the six mceusb devices I have myself.
Reported-by: Patrick Boettcher <pboettcher@kernellabs.com>
Reported-by: Lucian Muresan <lucianm@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CIR Wake FIFO is 67 bytes long, but the stock remote appears to only
populate 65 of them. Limit comparison to 65 bytes, and wake from suspend
works a whole lot better (it wasn't working at all for most folks).
Fix based on comparison with the old lirc_wb677 driver from Nuvoton,
debugging and testing done by Dave Treacy by way of the lirc mailing
list.
Reported-by: Dave Treacy <davetreacy@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The newest variants of the HVR-1600 have an s5h1411/tda18271 for the digital
frontend. Add support for these boards.
Thanks to Hauppauge Computer Works for providing sample hardware.
[awalls@md.metrocast.net: Changed an additional log message to clarify for
the end user that the driver is defaulting to an original HVR-1600 for
unknown model numbers.]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After upgrading the kernel from stock Ubuntu 7.10 to
10.04, with no hardware changes, I started getting the dreaded DMA
TIMEOUT errors, followed by inability to encode until the machine was
rebooted.
I came across a post from Andy in March
(http://www.gossamer-threads.com/lists/ivtv/users/40943#40943) where he
speculates that perhaps the corrective actions being taken after a DMA
ERROR are not sufficient to recover the situation. After some testing
I suspect that this is indeed the case, and that in fact the corrective
action may be what hangs the card's DMA engine, rather than the
original error.
Specifically these DMA ERROR IRQs seem to present with two different
values in the IVTV_REG_DMASTATUS register: 0x11 and 0x13. The current
corrective action is to clear that status register back to 0x01 or
0x03, and then issue the next DMA request. In the case of a 0x13 this
seems to result in a minor glitch in the encoded stream due to the
failed transfer that was not retried, but otherwise things continue OK.
In the case of a 0x11 the card's DMA write engine is never heard from
again, and a DMA TIMEOUT follows shortly after. 0x11 is the killer.
I suspect that the two cases need to be handled differently. The
difference is in bit 1 (0x02), which is set when the error is about to
be successfully recovered, and clear when things are about to go bad.
Bit 1 of DMASTATUS is described differently in different places either
as a positive "write finished", or an inverted "write busy". If we
take the first definition, then when an error arises with state 0x11,
it means that the write did not complete. It makes sense to start a
new transfer, as in the current code. But if we take the second
definition, then 0x11 means "an error but the write engine is still
busy". Trying to feed it a new transfer in this situation might not be
a good idea.
As an experiment, I added code to ignore the DMA ERROR IRQ if DMASTATUS
is 0x11. I.e., don't start a new transfer, don't clear our flags, etc.
The hope was that the card would complete the transfer and issue a ENC
DMA COMPLETE, either successfully or with an error condition there.
However the card still hung.
The only remaining corrective action being taken with a 0x11 status was
then the write back to the status register to clear the error, i.e.
DMASTATUS = DMASTATUS & ~3. This would have the effect of clearing the
error bit 4, while leaving the lower bits indicating DMA write busy.
Strangely enough, removing this write to the status register solved the
problem! If the DMA ERROR IRQ with DMASTATUS=0x11 is completely
ignored, with no corrective action at all, then the card will complete
the transfer and issue a new IRQ. If the status register is written to
when it has the value 0x11, then the DMA engine hangs. Perhaps it's
illegal to write to
DMASTATUS while the read or write busy bit is set? At any rate, it
appears that the current corrective action is indeed making things
worse rather than better.
I put together a patch that modifies ivtv_irq_dma_err to do the
following:
- Don't write back to IVTV_REG_DMASTATUS.
- If write-busy is asserted, leave the card alone. Just extend the
timeout slightly.
- If write-busy is de-asserted, retry the current transfer.
This has completely fixed my DMA TIMEOUT woes. DMA ERR events still
occur, but now they seem to be correctly handled. 0x11 events no
longer hang the card, and 0x13 events no longer result in a glitch in
the stream, as the failed transfer is retried. I'm happy.
I've inlined the patch below in case it is of interest. As described
above, I have a theory about why it works (based on a different
interpretation of bit 1 of DMASTATUS), but I can't guarantee that my
theory is correct. There may be another explanation, or it may be a
fluke. Maybe ignoring that IRQ entirely would be equally effective?
Maybe the status register read/writeback sequence is race condition if
the card changes it in the mean time? Also as I am using a PVR-150
only, I have not been able to test it on other cards, which may be
especially relevant for 350s that support concurrent decoding.
Hopefully the patch does not break the DMA READ path.
Mike
[awalls@md.metrocast.net: Modified patch to add a verbose comment, make minor
brace reformats, and clear the error flags in the IVTV_REG_DMASTATUS iff both
read and write DMA were not in progress. Mike's conjecture about a race
condition with the writeback is correct; it can confuse the DMA engine.]
[Comment and analysis from the ML post by Michael <mike@rsy.com>]
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the probing of cx2583x chips, because two controls were clustered
that are not created for these chips.
This regression was introduced in 2.6.36.
Signed-off-by: Sven Barth <pascaldragon@googlemail.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The previous revert-commit, that affected cx23885-i2c.c, left some
unused labels that the compiler griped about. Clean them up.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit 44835f197b.
With the CX23885 hardware I2C master, checking for I2C slave ACK/NAK
is not valid when the I2C_EXTEND or I2C_NOSTOP bits are set.
Revert the commit that checks for I2C slave ACK/NAK on all transactions,
so that XC5000 tuners work with the CX23885 again.
Thanks go to Mark Zimmerman for reporting and bisecting this problem.
Bisected-by: Mark Zimmerman <markzimm@frii.com>
Reported-by: Mark Zimmerman <markzimm@frii.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the pid filtering for the dib7000M demod. It also
corrects the pid filtering for the dib7700 based board. It should
prevent an oops, when using dib7700p based board.
References: https://bugzilla.novell.com/show_bug.cgi?id=644807
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Tested-by: Pavel SKARKA <paul.sp@seznam.cz>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the current matching rules the lookup for rc protocol named rc-5-sz matches with "rc-5" before finding "rc-5-sz". Thus one is able to never enable/disable the rc-5-sz protocol via sysfs.
Fix the lookup to require an exact match which allows the manipulation of sz protocol.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
__blk_run_queue() automatically either calls q->request_fn() directly
or schedules kblockd depending on whether the function is recursed.
blk-flush implementation needs to be able to explicitly choose
kblockd. Add @force_kblockd.
All the current users are converted to specify %false for the
parameter and this patch doesn't introduce any behavior change.
stable: This is prerequisite for fixing ide oops caused by the new
blk-flush implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
When support for 82577/82578 was added[1] in 2.6.31, PHY wakeup was in-
advertently enabled (even though it does not function properly) on ICH10
LOMs. This patch makes it so that the ICH10 LOMs use MAC wakeup instead
as was done with the initial support for those devices (i.e. 82567LM-3,
82567LF-3 and 82567V-4).
[1] commit a4f58f5455
Reported-by: Aurelien Jarno <aurelien@aurel32.net>
Cc: <stable@kernel.org>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sparse complains because the e1000 driver is calling ioread on a pointer
not tagged as __iomem.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
tps6586 does not support burst writes. i2c writes have to be
1 byte at a time.
Cc: stable@kernel.org
Signed-off-by: Varun Wadekar <vwadekar@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ASoC supports keeping the audio subsysetm active over suspend in order
to support use cases such as audio passthrough from a cellular modem
with the main CPU suspended. Ensure that we don't power down the CODEC
when this is happening by checking to see if VMID is up and skipping
suspend and resume when it is. If the CODEC has suspended then it'll
turn VMID off before the core suspend() gets called.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix the device name in DaVinci Voice Codec MFD driver to load
davinci-vcif and cq93vc codec client drivers.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
cpufreq_register_driver sets cpufreq_driver to a structure owned (and
placed) in the caller's memory. If cpufreq policy fails in its ->init
function, sysdev_driver_register returns nonzero in
cpufreq_register_driver. Now, cpufreq_register_driver returns an error
without setting cpufreq_driver back to NULL.
Usually cpufreq policy modules are unloaded because they propagate the
error to the module init function and return that.
So a later access to any member of cpufreq_driver causes bugs like:
BUG: unable to handle kernel paging request at ffffffffa00270a0
IP: [<ffffffff8145eca3>] cpufreq_cpu_get+0x53/0xe0
PGD 1805067 PUD 1809063 PMD 1c3f90067 PTE 0
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/virtual/net/tun0/statistics/collisions
CPU 0
Modules linked in: ...
Pid: 5677, comm: thunderbird-bin Tainted: G W 2.6.38-rc4-mm1_64+ #1389 To be filled by O.E.M./To Be Filled By O.E.M.
RIP: 0010:[<ffffffff8145eca3>] [<ffffffff8145eca3>] cpufreq_cpu_get+0x53/0xe0
RSP: 0018:ffff8801aec37d98 EFLAGS: 00010086
RAX: 0000000000000202 RBX: 0000000000000000 RCX: 0000000000000001
RDX: ffffffffa00270a0 RSI: 0000000000001000 RDI: ffffffff8199ece8
...
Call Trace:
[<ffffffff8145f490>] cpufreq_quick_get+0x10/0x30
[<ffffffff8103f12b>] show_cpuinfo+0x2ab/0x300
[<ffffffff81136292>] seq_read+0xf2/0x3f0
[<ffffffff8126c5d3>] ? __strncpy_from_user+0x33/0x60
[<ffffffff8116850d>] proc_reg_read+0x6d/0xa0
[<ffffffff81116e53>] vfs_read+0xc3/0x180
[<ffffffff81116f5c>] sys_read+0x4c/0x90
[<ffffffff81030dbb>] system_call_fastpath+0x16/0x1b
...
It's all cause by weird fail path handling in cpufreq_register_driver.
To fix that, shuffle the code to do proper handling with gotos.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Dave Jones <davej@redhat.com>
On a Thinkpad x61s, I noticed some memory corruption when
plugging/unplugging the external VGA connection. The symptoms are that
4 bytes at the beginning of a page get overwritten by zeroes.
The address of the corruption varies when rebooting the machine, but
stays constant while it's running (so it's possible to repeatedly write
some data and then corrupt it again by plugging the cable).
Further investigation revealed that the corrupted address is
(dev_priv->status_page_dmah->busaddr & 0xffffffff), ie. the beginning of
the hardware status page of the i965 graphics card, cut to 32 bits.
So it seems that for some memory access, the hardware uses only 32 bit
addressing. If the hardware status page is located >4GB, this
corrupts unrelated memory.
Signed-off-by: Jan Niehusmann <jan@gondor.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
This reverts commit c4ff4b829e.
Ted Ts'o reports:
"TPM is working for me so I can log into employer's network in 2.6.37.
It broke when I tried 2.6.38-rc6, with the following relevant lines
from my dmesg:
[ 11.081627] tpm_tis 00:0b: 1.2 TPM (device-id 0x0, rev-id 78)
[ 25.734114] tpm_tis 00:0b: Operation Timed out
[ 78.040949] tpm_tis 00:0b: Operation Timed out
This caused me to get suspicious, especially since the _other_ TPM
commit in 2.6.38 had already been reverted, so I tried reverting
commit c4ff4b829e: "TPM: Long default timeout fix". With this commit
reverted, my TPM on my Lenovo T410 is once again working."
Requested-and-tested-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This finally makes TX on OFDM rates possible on my dev with PHY rev 4.
We still have lower performance than wl, but at least speeds around 15M
become possible.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AID and BSSID should be set in the HW only for the
first station interface or adhoc interface. Also, cancel
the ANI timer in stop() for multi-STA scenario. And finally
configure the HW beacon timers only for the first station
interface.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- adjust code of rtl8169_set_speed_xmii function
- remove parts of code which are done in rtl_pll_power_up
function (8168 only)
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Several ACPI drivers fail to build if CONFIG_NET is unset, because
they refer to things depending on CONFIG_THERMAL that in turn depends
on CONFIG_NET. However, CONFIG_THERMAL doesn't really need to depend
on CONFIG_NET, because the only part of it requiring CONFIG_NET is
the netlink interface in thermal_sys.c.
Put the netlink interface in thermal_sys.c under #ifdef CONFIG_NET
and remove the dependency of CONFIG_THERMAL on CONFIG_NET from
drivers/thermal/Kconfig.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Len Brown <lenb@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Luming Yu <luming.yu@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: fix unsigned vs signed comparison issue in modeset ctl ioctl.
drm/nv50-nvc0: make sure vma is definitely unmapped when destroying bo
All features originally planned for version 3.1 (and some that
weren't) have been implemented.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
In Falcon we can configure the fill levels of the RX data FIFO which
trigger the generation of pause frames (if enabled), and we have
module parameters for this.
Siena does not allow the levels to be configured (or, if it does, this
is done by the MC firmware and is not configurable by drivers).
So far as I can tell, the module parameters are not used by our
internal scripts and have not been documented (with the exception of
the short parameter descriptions). Therefore, remove them and always
initialise Falcon with the default values.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This field does not exist in all MMDs we want to check, and all
callers allow it to be set (fault_fatal = 0).
Remove the loopback condition, as STAT2.DEVPRST should be valid
regardless of any fault.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We currently make no use of siena_nic_data::fw_{version,build} except
to format the firmware version for ethtool_get_drvinfo(). Since we
only read the version at start of day, this information is incorrect
after an MC firmware update. Remove the cached version information
and read it via MCDI whenever it is requested.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Instead calculate the KVA of receive data. It's not like it's a hard sum.
[bwh: Fixed to work with GRO.]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Clearly it should be the size of ->ip_dst here.
Although this is harmless, but it still reads odd.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an additional check in the Davinci EMAC RX Handler,
which tests the __LINK_STATE_NOCARRIER flag along with the
__LINK_STATE_START flag as part EMAC shutting down procedure.
This avoids
WARNING: at drivers/net/davinci_emac.c:1040 emac_rx_handler+0xf8/0x120()
during rtcwake used to suspend the target for a specified duration.
Signed-off-by: Hegde, Vinay <vinay.hegde@ti.com>
Acked-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix FW initialization according to max BW stored in percents
for NPAR mode. Protect HW from being configured to speed 0.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a port profile disassociate all address registrations for the interface
are blown away from the adapter. This patch resets the driver cache of
registered address lists to zero after a port profile disassociate.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow randomised ethernet address if the device does not have a valid
EEPROM or pre-set MAC address.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add necessary annotations about pointer to io memory space
that is checked by sparse.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix use of zero where NULL expected. And wrap long line.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is similar to what we already do in cdc-phonet.c in the same
situation. pskb_pull() refuses to work with HIGHMEM, even if it is
known that the socket buffer is entirely in "low" memory.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver uses PCI_CLASS_REVISION instead of PCI_REVISION_ID, so it wasn't
converted by commit 44c10138fd (PCI: Change all
drivers to use pci_device->revision).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_set_drvdata() was used with argument of incorrect type and
could cause memory corruption. Moreover, because of not setting drvdata
in the correct place not all resources were freed upon module unload.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 71d6429 (Driver core: convert platform_{get,set}_drvdata to
static inline functions) now triggers a warning in the macb network
driver:
CC drivers/net/macb.o
drivers/net/macb.c: In function ‘macb_mii_init’:
drivers/net/macb.c:263: warning: passing argument 1 of ‘platform_set_drvdata’ from incompatible pointer type
include/linux/platform_device.h:138: note: expected ‘struct platform_device *’ but argument is of type ‘struct net_device *’
Use dev_set_drvdata() on the device embedded in the net_device instead.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch the bnx2x uses the generic dcbnl application tlv list
instead of implementing its own get-app handler. When the driver is
alerted to a change in the DCB negotiated parameters, it calls
dcb_setapp to update the dcbnl application tlvs list making it available
to user mode applications and registered notifiers.
Signed-off-by: Shmulik Ravid <shmulikr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I just found that the controller hardware name is not set for the Softing
driver. After this patch, "$ ip -d link show" looks nicer.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The below patch changes a typo "pice" to "piece"
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fmvj18x_cs:add new id
Toshiba lan&modem multifuction card (model name:IPC5010A)
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several more network drivers that read the device's revision ID
from the PCI configuration register were merged after the commit
44c10138fd (PCI: Change all drivers
to use pci_device->revision), so it's time to do another pass of
conversion to using the 'revision' field of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to have separate iwl-agn-rx.c file after iwlegacy
split.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove check_plcp_health and check_ack_health ops methods, they are
unneeded after iwlegacy driver split. Merge check health code into to
iwl-rx.c and make functions static.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add module ack_check, and plcp_check parameters. Ack_check is disabled
by default since is proved that check ack health can cause troubles.
Plcp_check is enabled by default.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix possible dma mappings and skbs introduced by commit
470058e0ad "iwlwifi: avoid Tx queue
memory allocation in interface down".
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit commit 470058e0ad
"iwlwifi: avoid Tx queue memory allocation in interface down" we do
not unmap dma and free skbs when down device and there is pending
transfer. What in consequence may cause that system hung (waiting
for free skb's) when performing shutdown at iptables module unload.
DMA leak manifest itself following warning:
WARNING: at lib/dma-debug.c:689 dma_debug_device_change+0x15a/0x1b0()
Hardware name: HP xw8600 Workstation
pci 0000:80:00.0: DMA-API: device driver has pending DMA allocations while released from device [count=240]
Modules linked in: iwlagn(-) aes_x86_64 aes_generic fuse cpufreq_ondemand acpi_cpufreq freq_table mperf xt_physdev ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables ipv6 ext3 jbd dm_mirror dm_region_hash dm_log dm_mod uinput hp_wmi sparse_keymap sg wmi microcode serio_raw tg3 arc4 ecb shpchp mac80211 cfg80211 rfkill ext4 mbcache jbd2 sr_mod cdrom sd_mod crc_t10dif firewire_ohci firewire_core crc_itu_t mptsas mptscsih mptbase scsi_transport_sas pata_acpi ata_generic ata_piix ahci libahci floppy nouveau ttm drm_kms_helper drm i2c_algo_bit i2c_core video [last unloaded: iwlagn]
Pid: 9131, comm: rmmod Tainted: G W 2.6.38-rc6-wl+ #33
Call Trace:
[<ffffffff810649ef>] ? warn_slowpath_common+0x7f/0xc0
[<ffffffff81064ae6>] ? warn_slowpath_fmt+0x46/0x50
[<ffffffff812320ab>] ? dma_debug_device_change+0xdb/0x1b0
[<ffffffff8123212a>] ? dma_debug_device_change+0x15a/0x1b0
[<ffffffff8149dc18>] ? notifier_call_chain+0x58/0xb0
[<ffffffff8108e370>] ? __blocking_notifier_call_chain+0x60/0x90
[<ffffffff8108e3b6>] ? blocking_notifier_call_chain+0x16/0x20
[<ffffffff812f570c>] ? __device_release_driver+0xbc/0xe0
[<ffffffff812f5808>] ? driver_detach+0xd8/0xe0
[<ffffffff812f45d1>] ? bus_remove_driver+0x91/0x100
[<ffffffff812f6022>] ? driver_unregister+0x62/0xa0
[<ffffffff8123d5d4>] ? pci_unregister_driver+0x44/0xa0
[<ffffffffa05632d1>] ? iwl_exit+0x15/0x1c [iwlagn]
[<ffffffff810ab492>] ? sys_delete_module+0x1a2/0x270
[<ffffffff81498da9>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<ffffffff8100bf42>] ? system_call_fastpath+0x16/0x1b
I still can observe above warning after apply patch, but it is very
hard to reproduce it, and have count=1. Whereas that one is easy to
reproduce using debugfs force_reset while transmitting data, and have
very big counts eg. 240, like quoted here. So count=1 WARNING seems
to be different issue that need to be resolved separately.
v1 -> v2: fix infinity loop bug I made during "for" to "while" loop transition.
v2 -> v3: remove unneeded EXPORT_SYMBOL
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9485 doesn't use the default GPIO pin for LED and GPIO 6 is actually
used for this.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the RSSI calibration table was not found or not parsed properly,
priv->rssi_db will be NULL, p54_rssi_find needs to be able to deal
with that.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/rtlwifi/rtl8192ce/trx.c: In function ‘rtl92ce_rx_query_desc’:
drivers/net/wireless/rtlwifi/rtl8192ce/trx.c:255:5: warning: ‘rf_rx_num’ may be used uninitialized in this function
drivers/net/wireless/rtlwifi/rtl8192ce/trx.c:257:12: warning: ‘total_rssi’ may be used uninitialized in this function
drivers/net/wireless/rtlwifi/rtl8192ce/trx.c:466:6: warning: ‘weighting’ may be used uninitialized in this function
This work was supported by a hardware donation from the CE Linux Forum.
Signed-off-by: Alessio Igor Bogani <abogani@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rate_mask is initialized again later so this can be removed. Btw, if
rate_control_send_low(sta, priv_sta, txrc) returns false, that means
that "sta" is non-NULL. That's why the second initialization of
rate_mask is a little simpler than the first.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Mark Davis
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/at76c50x-usb.o
drivers/net/wireless/at76c50x-usb.c: In function ‘at76_mac80211_tx’:
drivers/net/wireless/at76c50x-usb.c:1759:4: warning: ‘return’ with a value, in function returning void
This is fallout from commit 7bb4568372
("mac80211: make tx() operation return void").
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The stream length/tag fields have to be in little endian
format. Fixing this makes the driver work on big-endian
platforms.
Cc: stable@kernel.org
Tested-by: raghunathan.kailasanathan@wipro.com
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts bonding to use rx_handler. Results in cleaner
__netif_receive_skb() with much less exceptions needed. Also
bond-specific work is moved into bond code.
Did performance test using pktgen and counting incoming packets by
iptables. No regression noted.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Reviewed-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow fixes a misrendering + hang at GDM startup on my NVA8...
My first guess would have been stale TLB entries laying around that a new
bo then accidentally inherits. That doesn't make a great deal of sense
however, as when we mapped the pages for the new bo the TLBs would've
gotten flushed anyway.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
V4: rebase to net-next-2.6
This patch removes the flag IFF_IN_NETPOLL, we don't need it any more since
we have netpoll_tx_running() now.
Signed-off-by: WANG Cong <amwang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
V4: rebase to net-next-2.6
V3: remove an useless #ifdef.
This patch unifies the netpoll code in bonding with netpoll code in bridge,
thanks to Herbert that code is much cleaner now.
Signed-off-by: WANG Cong <amwang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PXA supports multi-machine kernels since long ago. However a kernel
compiled with support for colibri and any other PXA machine and with
PCMCIA enabled will barf at runtime about duplicate registration of
pxa2xx-pcmcia device. Fix that.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
If a qeth device is set offline, data and control subchannels are
cleared, which means removal of all IP Assist Primitive settings
implicitly. There is no need to delete those settings explicitly.
This patch removes all IP Assist invocations from offline.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device table is required to load modules based on modaliases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The device table is required to load modules based on modaliases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Fixes sysfs config attribute to allow access to entire 16MB maintenance
space of RapidIO devices.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initialize ts_real.flags to fix compiler warning about possible
uninitialized use of this field.
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In linux rtc_time struct, tm_mon range is 0~11, tm_wday range is 0~6,
while in RTC HW REG, month range is 1~12, day of the week range is 1~7,
this patch adjusts difference of them.
The efect of this bug was that most of month will be operated on as the
next month by the hardware (When in Jan it maybe even worse). For
example, if in May, software wrote 4 to the hardware, which handled it as
April. Then the logic would be different between software and hardware,
which would cause weird things to happen.
Signed-off-by: Lei Xu <B33228@freescale.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Jack Lan <jack.lan@freescale.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The regulator framework is used for power management. The regulators are
only named in the driver code, the actual control stuff is in the board
file for each architecture or use case.
The PN544 chip has three regulators that can be controlled or not -
depending on the architecture where the chip is being used. So some of
the regulators may not be controllable. In our current case the third
regulator, which was missing from the code, went unnoticed because we
didn't need to control it. To be as general as possible - in this respect
- the driver needs to list all regulators. Then the board file can be
used to actually set the usage.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Spell out the NFC acronym when it's shown for the first time.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator, mc13xxx: Remove pointless test for unsigned less than zero
regulator: Fix warning with CONFIG_BUG disabled
drivers/net/wireless/iwlegacy/built-in.o:(.rodata+0x29f0): multiple definition of `iwl_rates'
drivers/net/wireless/iwlwifi/built-in.o:(.rodata+0xa68): first defined here
powerpc64-linux-ld: Warning: size of symbol `iwl_rates' changed from 143 in drivers/net/wireless/iwlwifi/built-in.o to 130 in drivers/net/wireless/iwlegacy/built-in.o
drivers/net/wireless/iwlegacy/built-in.o:(.data+0x0): multiple definition of `bt_coex_active'
drivers/net/wireless/iwlwifi/built-in.o:(.data+0x668): first defined here
drivers/net/wireless/iwlegacy/built-in.o:(.rodata+0x750): multiple definition of `iwl_eeprom_band_1'
drivers/net/wireless/iwlwifi/built-in.o:(.rodata+0x27d0): first defined here
drivers/net/wireless/iwlegacy/built-in.o:(.rodata+0x3f0): multiple definition of `iwl_bcast_addr'
drivers/net/wireless/iwlwifi/built-in.o:(.rodata+0x24f8): first defined here
drivers/net/wireless/iwlegacy/built-in.o:(.bss+0x3d48): multiple definition of `iwl_debug_level'
drivers/net/wireless/iwlwifi/built-in.o:(.bss+0x21950): first defined here
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The member of the rtc_class_ops struct is called alarm_irq_enable and
not alarm_irq_enabled
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jelle Martijn Kok <jmkok@youcom.nl>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initialize txq to avoid this warning:
drivers/net/wireless/ath/ath9k/main.c: In function ‘ath9k_flush’:
drivers/net/wireless/ath/ath9k/main.c:2138: warning: ‘txq’ may be used uninitialized in this function
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pll_work should be cancelled on full_sleep or it may cause
redundant chip reset.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes tramissing on OFDM rates for PHYs 1 and 2. There is
still something wrong with PHYs 3+. Tests has shown decreasing of
performance on CCK rates by 1-2%, we have to live with that.
Additionaly this noticeably reduces amount of PHY errors. They were
mostly produced by auto-switching to higher rate for better
performanced, which resulted in no transmit at all and PHY errors.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function was intended to calculate the
number of RX chains needed, but could only
work where the AP's streams were asymmetric,
i.e. 2 TX and 3 RX or similar. In the case
where IEEE80211_HT_MCS_TX_RX_DIFF was not
set, this function would calculate the wrong
information.
Additionally, mac80211 didn't pass through
the required values at all, so it couldn't
work anyway.
Rewrite the logic in this function and add
appropriate comments to make it readable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the frequency can not be mapped to a channel structure log it and drop it.
Signed-off-by: Joseph J. Gunn <armadefuego@yahoo.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return value of the tx operation is commonly
misused by drivers, leading to errors. All drivers
will drop frames if they fail to TX the frame, and
they must also properly manage the queues (if they
didn't, mac80211 would already warn).
Removing the ability for drivers to return a BUSY
value also allows significant cleanups of the TX
TX handling code in mac80211.
Note that this also fixes a bug in ath9k_htc, the
old "return -1" there was wrong.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com> [ath5k]
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> [rt2x00]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net> [b43, rtl8187, rtlwifi]
Acked-by: Luciano Coelho <coelho@ti.com> [wl12xx]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Same fix as f844a709a7
"iwlwifi: do not set tx power when channel is changing".
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The callback sets slot time as specified in IEEE 802.11-2007
section 17.3.8.6 and raises round trip delay accordingly.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BCM4320a breaks when enabling power save (bug 29732). So disable power save
for anything but BCM4320b that is known to work.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"AirLive X.USB now works perfectly under a Linux
environment!"
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 4df3071ebd "ath9k_hw: optimize
interrupt mask changes", changed ath9k_hw_set_interrupts function to
enable interrupts regardless of function argument, what could possibly
be wrong. Correct that behaviour and check "ints" arguments before
enabling interrupts, also disable interrupts if ints do not have
ATH9K_INT_GLOBAL flag set.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
usb: musb: core: set has_tt flag
USB: xhci: mark local functions as static
USB: xhci: fix couple sparse annotations
USB: xhci: rework xhci_print_ir_set() to get ir set from xhci itself
USB: Reset USB 3.0 devices on (re)discovery
xhci: Fix an error in count_sg_trbs_needed()
xhci: Fix errors in the running total calculations in the TRB math
xhci: Clarify some expressions in the TRB math
xhci: Avoid BUG() in interrupt context
* 'for-linus' of git://neil.brown.name/md:
md: Fix - again - partition detection when array becomes active
Fix over-zealous flush_disk when changing device size.
md: avoid spinlock problem in blk_throtl_exit
md: correctly handle probe of an 'mdp' device.
md: don't set_capacity before array is active.
md: Fix raid1->raid0 takeover
The variable 'val' is a 'unsigned int', so it can never be less than zero.
This fact makes the "val < 0" part of the test done in BUG_ON() in
mc13xxx_regulator_get_voltage() rather pointles since it can never have
any effect.
This patch removes the pointless test.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The API for network devices has changed so that setting carrier off at
probe is no longer required. This should fix the IPv6 addrconf issue.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=29612
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reported-by: George Billios <gbillios@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Fix unintended recursion in ironlake_disable_rc6
drm/i915: fix corruptions on i8xx due to relaxed fencing
drm/i915: skip FDI & PCH enabling for DP_A
agp/intel: Experiment with a 855GM GWB bit
drm/i915: don't enable FDI & transcoder interrupts after all
drm/i915: Ignore a hung GPU when flushing the framebuffer prior to a switch
On my G5 this fails to compile with
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c:701: error: __ksymtab__rtl92c_phy_txpwr_idx_to_dbm causes a section type conflict
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c:701: error: __ksymtab__rtl92c_phy_txpwr_idx_to_dbm causes a section type conflict
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c:677: error: __ksymtab__rtl92c_phy_dbm_to_txpwr_Idx causes a section type conflict
drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c:677: error: __ksymtab__rtl92c_phy_dbm_to_txpwr_Idx causes a section type conflict
since you can't export static functions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MUSB is a non-standard host implementation which
can handle all speeds with the same core. We need
to set has_tt flag after commit
d199c96d41 (USB: prevent
buggy hubs from crashing the USB stack) in order for
MUSB HCD to continue working.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Michael Jones <michael.jones@matrix-vision.de>
Tested-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit bba63a2 (ACPICA: Implicit notify support) introduced a
mechanism that causes a notify request of type
ACPI_NOTIFY_DEVICE_WAKE to be queued automatically by
acpi_ev_asynch_execute_gpe_method() for the device whose _PRW points
to the GPE being handled if that GPE is not associated with an
_Lxx/_Exx method. However, it turns out that on some systems there
are multiple devices with _PRW pointing to the same GPE without
_Lxx/_Exx and the mechanism introduced by commit bba63a2 needs to be
extended so that "implicit" notify requests of type
ACPI_NOTIFY_DEVICE_WAKE can be queued automatically for all those
devices at the same time.
Reported-and-tested-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
File position is not controlled, it may lead to overwrites of arbitrary
kernel memory. Also the code may kfree() the same pointer multiple
times.
One more flaw is still present: if multiple processes open the file then
all 3 static variables are shared, leading to various race conditions.
They should be moved to file->private_data.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Reviewed-by: Eugene Teo <eugeneteo@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
After disabling, we're meant to teardown the bo used for the contexts,
not recurse into ourselves again and preventing module unload.
Reported-and-tested-by: Ben Widawsky <bwidawsk@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This will synchronize the version with the out of tree driver which
shares its functionality.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fix updates copyright information to include current year 2011.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implemented igb_ndo_set_vf_bw function which is being used
by iproute2 tool. In addition, updated igb_ndo_get_vf_config function
to show the actual rate limit to the user.
The rate limitation can be configured only when the link is up.
The rate limit value can be ranged between 0 and actual
link speed measured in Mbps. A value of '0' disables the rate limit for
this specific VF.
iproute2 usage will be 'ip link set ethX vf Y rate Z'.
After the command is made, the rate will be changed instantly.
To view the current rate limit, use 'ip link show ethX'.
The rates will be zeroed only upon driver reload or a link speed change.
This feature is being supported only by 82576 device.
Signed-off-by: Lior Levy <lior.levy@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removed Tx hang detection mechanism from igbvf.
This mechanism has no affect and can cause false alarm message in some cases.
Signed-off-by: Lior Levy <lior.levy@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some of the function names in function header comments did not match
actual name of the function.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 controller allows jumbo frame setup on a per VF basis. Enable
use of jumbo frames when the VF device belongs to the X540 controller.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 controller supports jumbo frames in SR-IOV mode. Allow
configuration of jumbo frames either in the PF driver or on behalf of
a VF.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Revert
b821eaa572
and
f3b99be19d
When I wrote the first of these I had a wrong idea about the
lifetime of 'struct block_device'. It can disappear at any time that
the block device is not open if it falls out of the inode cache.
So relying on the 'size' recorded with it to detect when the
device size has changed and so we need to revalidate, is wrong.
Rather, we really do need the 'changed' attribute stored directly in
the mddev and set/tested as appropriate.
Without this patch, a sequence of:
mknod / open / close / unlink
(which can cause a block_device to be created and then destroyed)
will result in a rescan of the partition table and consequence removal
and addition of partitions.
Several of these in a row can get udev racing to create and unlink and
other code can get confused.
With the patch, the rescan is only performed when needed and so there
are no races.
This is suitable for any stable kernel from 2.6.35.
Reported-by: "Wojcik, Krzysztof" <krzysztof.wojcik@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
There are two cases when we call flush_disk.
In one, the device has disappeared (check_disk_change) so any
data will hold becomes irrelevant.
In the oter, the device has changed size (check_disk_size_change)
so data we hold may be irrelevant.
In both cases it makes sense to discard any 'clean' buffers,
so they will be read back from the device if needed.
In the former case it makes sense to discard 'dirty' buffers
as there will never be anywhere safe to write the data. In the
second case it *does*not* make sense to discard dirty buffers
as that will lead to file system corruption when you simply enlarge
the containing devices.
flush_disk calls __invalidate_devices.
__invalidate_device calls both invalidate_inodes and invalidate_bdev.
invalidate_inodes *does* discard I_DIRTY inodes and this does lead
to fs corruption.
invalidate_bev *does*not* discard dirty pages, but I don't really care
about that at present.
So this patch adds a flag to __invalidate_device (calling it
__invalidate_device2) to indicate whether dirty buffers should be
killed, and this is passed to invalidate_inodes which can choose to
skip dirty inodes.
flusk_disk then passes true from check_disk_change and false from
check_disk_size_change.
dm avoids tripping over this problem by calling i_size_write directly
rathher than using check_disk_size_change.
md does use check_disk_size_change and so is affected.
This regression was introduced by commit 608aeef17a which causes
check_disk_size_change to call flush_disk, so it is suitable for any
kernel since 2.6.27.
Cc: stable@kernel.org
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Andrew Patterson <andrew.patterson@hp.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NeilBrown <neilb@suse.de>
This reverts commit 556ea928f7.
Jeff Chua reports that it can cause some bluetooth devices (he mentions
an Bluetooth Intermec scanner) to just stop responding after a while
with messages like
[ 4533.361959] btusb 8-1:1.0: no reset_resume for driver btusb?
[ 4533.361964] btusb 8-1:1.1: no reset_resume for driver btusb?
from the kernel. See also
https://bugzilla.kernel.org/show_bug.cgi?id=26182
for other reports.
Reported-by: Jeff Chua <jeff.chua.linux@gmail.com>
Reported-by: Andrew Meakovski <meako@bigmir.net>
Reported-by: Jim Faulkner <jfaulkne@ccs.neu.edu>
Acked-by: Greg KH <gregkh@suse.de>
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Cc: stable@kernel.org (for 2.6.37)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: fix corruptions on i8xx due to relaxed fencing
drm/i915: skip FDI & PCH enabling for DP_A
agp/intel: Experiment with a 855GM GWB bit
drm/i915: don't enable FDI & transcoder interrupts after all
drm/i915: Ignore a hung GPU when flushing the framebuffer prior to a switch
It looks like gen2 has a peculiar interleaved 2-row inter-tile
layout. Probably inherited from i81x which had 2kb tiles (which
naturally fit an even-number-of-tile-rows scheme to fit onto 4kb
pages). There is no other mention of this in any docs (also not
in the Intel internal documention according to Chris Wilson).
Problem manifests itself in corruptions in the second half of the
last tile row (if the bo has an odd number of tiles). Which can
only happen with relaxed tiling (introduced in a00b10c360).
So reject set_tiling calls that don't satisfy this constrain to
prevent broken userspace from causing havoc. While at it, also
check the size for newer chipsets.
LKML: https://lkml.org/lkml/2011/2/19/5
Reported-by: Indan Zupancic <indan@nul.nu>
Tested-by: Indan Zupancic <indan@nul.nu>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
Added support for usb ethernet (0x0fe6, 0x9700)
r8169: fix RTL8168DP power off issue.
r8169: correct settings of rtl8102e.
r8169: fix incorrect args to oob notify.
DM9000B: Fix PHY power for network down/up
DM9000B: Fix reg_save after spin_lock in dm9000_timeout
net_sched: long word align struct qdisc_skb_cb data
sfc: lower stack usage in efx_ethtool_self_test
bridge: Use IPv6 link-local address for multicast listener queries
bridge: Fix MLD queries' ethernet source address
bridge: Allow mcast snooping for transient link local addresses too
ipv6: Add IPv6 multicast address flag defines
bridge: Add missing ntohs()s for MLDv2 report parsing
bridge: Fix IPv6 multicast snooping by correcting offset in MLDv2 report
bridge: Fix IPv6 multicast snooping by storing correct protocol type
p54pci: update receive dma buffers before and after processing
fix cfg80211_wext_siwfreq lock ordering...
rt2x00: Fix WPA TKIP Michael MIC failures.
ath5k: Fix fast channel switching
tcp: undo_retrans counter fixes
...
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
amd64-agp: fix crash at second module load
drm/radeon: fix regression with AA resolve checking
drm: drop commented out code and preceding comment
drm/vblank: Enable precise vblank timestamps for interlaced and doublescan modes.
drm/vblank: Use memory barriers optimized for atomic_t instead of generics.
drm/vblank: Use abs64(diff_ns) for s64 diff_ns instead of abs(diff_ns)
drm/radeon/kms: align height of fb allocation.
Revert "drm/radeon/kms: switch back to min->max pll post divider iteration"
The device is very similar to (0x0fe6, 0x8101),
And works well with dm9601 driver.
Signed-off-by: Shahar Havivi <shaharh@redhat.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix the RTL8111DP turn off the power when DASH is enabled.
- RTL_GIGA_MAC_VER_27 must wait for tx finish before reset.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Adjust and remove certain settings of RTL8102E which are for previous chips.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-off-by: Francois Romieu <romieu@fr.zoreil.com>
It results in the wrong point address and influences RTL8168DP.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
DM9000 revision B needs 1 ms delay after PHY power-on.
PHY must be powered on by writing 0 into register DM9000_GPR before
all other settings will change (see Davicom spec and example code).
Remember, that register DM9000_GPR was not changed by reset sequence.
Without this fix the FIFO is out of sync and sends wrong data after
sequence of "ifconfig ethX down ; ifconfig ethX up".
Signed-off-by: David S. Miller <davem@davemloft.net>
Max rx queues and tx queues are governed by fimware.
So driver should not validate these values.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Remove checks of 1 for auto_fw_reset module parameter.
auto_fw_reset is of type int and can have value > 1.
o Remove unnecessary #define for 1
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original code does not work well when the number of mulitcast
address to handle is greater than MCAST_MAX. It only enable promiscous
mode instead of multicast hash table mode, so the hash table function
will not be activated and all multicast frames will be recieved in this
condition.
This patch fixes the following issues with the r6040 NIC operating in
multicast:
1) When the IFF_ALLMULTI flag is set, we should write 0xffff to the NIC
hash table registers to make it process multicast traffic.
2) When the number of multicast address to handle is smaller than
MCAST_MAX, we should use the NIC multicast registers MID1_{L,M,H}.
3) The hashing of the address was not correct, due to an invalid
substraction (15 - (crc & 0x0f)) instead of (crc & 0x0f) and an
incorrect crc algorithm (ether_crc_le) instead of (ether_crc).
4) If necessary, we should set HASH_EN flag in MCR0 to enable multicast
hash table function.
Reported-by: Marc Leclerc <marc-leclerc@signaturealpha.com>
Tested-by: Marc Leclerc <marc-leclerc@signaturealpha.com>
Signed-off-by: Shawn Lin <shawn@dmp.com.tw>
Signed-off-by: Albert Chen <albert.chen@rdc.com.tw>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dmaw_block is an enum and max_pay_load is u32. Therefore
sparse gives warning about comparison of unsigned and signed value.
Resolve by using min_t to force cast.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted by Stephan Rothwell, an allyesconfig build fails since rtl8192cu
was merged with failures such as:
drivers/net/wireless/rtlwifi/rtl8192cu/built-in.o: In function `rtl92c_phy_sw_chnl':
(.opd+0xf30): multiple definition of `rtl92c_phy_sw_chnl'
drivers/net/wireless/rtlwifi/rtl8192ce/built-in.o:(.opd+0xb70): first defined here
drivers/net/wireless/rtlwifi/rtl8192cu/built-in.o: In function `rtl92c_fill_h2c_cmd':
(.opd+0x288): multiple definition of `rtl92c_fill_h2c_cmd'
drivers/net/wireless/rtlwifi/rtl8192ce/built-in.o:(.opd+0x288): first defined here
These are caused because the code shared between rtl8192ce and rtl8192cu
is included in both drivers. This has been fixed by creating a new modue that
contains the shared code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On ARM, compilation of rtlwifi/efuse.c fails with the message:
ERROR: "__bad_udelay" [drivers/net/wireless/rtlwifi/rtlwifi.ko] undefined!
On inspection, the faulty calls are in routine efuse_reset_loader(), a
routine that is never used, and the faulty routine is deleted.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On systems where PCI does not exist, a build of rtlwifi will fail.
Apply the same fix in case there are systems with PCI but not USB.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On the ARM system, a build fails due to missing include.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wireless Makefile does not build rtlwifi for rtl8192cu unless
rtl8192ce is selected.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flag isn't very descriptive -- the intention
is that the driver provides a TSF timestamp at
the beginning of the MPDU -- make that clearer
by renaming the flag to RX_FLAG_MACTIME_MPDU.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hif_usb_alloc_urbs() takes care of freeing
all the allocated URBs for the various endpoints when
an error occurs. Calling ath9k_hif_usb_dealloc_urbs() would
cause a panic since the URBs have already been freed.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ATH9K_RX_FILTER_UNCOMP_BA_BAR and ATH9K_RX_FILTER_PSPOLL
when mac80211 requires it.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to set the BSSID mask or opmode when
initializing RX, they would be set correctly in the HW reset
routine.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The target beacon transmission time has to be synced with the HW
TSF when configuring beacon timers in Adhoc mode. Failing to do this
would cause erroneous beacon transmission, for example, on completion
of a scan run to check for IBSS merges.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle multi-interface situations by checking if
AP interfaces are already present.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The time granularity for the ANI task is different for AP and
station mode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required for allowing only one IBSS interface to be
configured.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required when issuing commands to the firmware.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to use a locally stored reference.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 stores the association state in ieee80211_bss_conf.
Use this and remove the local state, which is incorrect anyway
since it is stored globally and not on a per-VIF basis.
Restarting ANI and reconfiguration of HW beacon timers when a
scan run ends requires more work. This is handled by iterating
over the active interfaces.
Finally, remove the useless check for associated status in RX
processing.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CTS protection can be obtained from mac80211 directly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211's BSS info can be used for this.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Addition of a station might fail - handle this error
properly by removing the VAP on the target.
Also, bail out immediately if the max. no of interfaces
has been reached.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update capabilites on the target once, when
start() is called, there is no need for redundant
updating on adding an interface.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple interfaces can be configured if a slot is free
on the target. Monitor mode also requires a slot.
The maximum number of stations that can be handled in
the firmware is 8, manage the station slots accordingly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some AR7010 based devices are recognized as storage media.
Sending a CD-EJECT command to the device will 'convert' it into
a WLAN device. Do this within the driver itself, removing the
dependancy on an external program (usb_modeswitch).
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All mwl8k parts perform rate control in firmware. Make this known to
mac80211 so that it does not launch minstrel. Also, because actual tx
rate information is not available from the firmware, invalidate the
rate status before returning the skb to mac80211.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When configuring rx antennas using CMD_RF_ANTENNA, the argument input is
the number of antennas to be enabled. For AP, we support 3 rx antennas
and hence set the field to 3. For tx antennas, value is a bitmap, so 0x7
enables all three.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 8ee294cd9d converted serio
subsystem event handling from using a dedicated thread to using
common workqueue. Unfortunately, this regressed our boot times,
due to the fact that serio jobs take long time to execute. While
the new concurrency managed workqueue code manages long-playing
works just fine and schedules additional workers as needed, such
works wreck havoc among remaining users of flush_scheduled_work().
To solve this problem let's move serio/gameport works from system_wq
to system_long_wq which nobody tries to flush.
Reported-and-tested-by: Hernando Torque <pantherchen@versanet.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since Synaptics technical writers department is a bit slow releasing updated
Synaptics interface guide, let's add some new bits (with their blessing)
to the code so that they don't get lost.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Update the PS mode of each link according to a bitmap polled from
fw_status. Manually notify mac80211 about PS mode changes in connected
stations.
mac80211 will only be notified about PS start when the station is in PS
and there is a small number of TX blocks from this link ready in HW.
This is required for waking up the remote station since the TIM is
updated entirely by FW.
When a station enters mac80211-PS-mode, we drop all the skbs in the
low-level TX queues belonging to this sta with STAT_TX_FILTERED
to keep our queues clean.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Count the number of FW TX blocks allocated per link. We add blocks to a
link counter when allocated for a TX descriptor. We remove blocks
according to counters in fw_status indicating the number of freed blocks
in FW. These counters are polled after each IRQ.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Remove an active hlid when chip wakeup fails. In addition rename the
involved functions.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When operating in AP mode the wl1271 hardware filters out null-data
packets as well as management packets. This makes it impossible for
mac80211 to monitor the PS mode by using the PM bit of incoming frames.
Disable mac80211 automatic link PS-mode handling by supporting
IEEE80211_HW_AP_LINK_PS in HW flags.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Report a TX rate idx of -1 and count 0 when returning untransmitted
skbs to mac80211 using ieee80211_tx_status(). Otherwise mac80211
tries to use the returned (essentially garbage) status.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When operating in AP-mode we require a per link tx-queue.
This allows us to implement HW assisted PS mode for links,
as well as regulate per-link FW TX blocks consumption.
Split each link into ACs to support future QoS for AP-mode.
AC queues are emptied in priority and per-link queues are
scheduled in a simple round-robin fashion.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If a sta starts transmitting immediately after authentication, sometimes
the FW deauthenticates it. Fix this by marking the sta "in-connection"
in FW before sending the autentication response.
The "in-connection" entry is automatically removed when connection
succeeds or after a timeout.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Check the conditions for the high/low TX queue watermarks when the
spin-lock is taken. This prevents race conditions as tx_queue_count and
the flag checked are only modified when the spin-lock is taken.
The following race was in mind:
- Queues are almost full and wl1271_op_tx() will stop the queues, but it
doesn't get the spin-lock yet.
- (on another CPU) tx_work_locked() dequeues 15 skbs from this queue and
tx_queue_count is updated to reflect this
- wl1271_op_tx() does not check tx_queue_count after taking the
spin-lock and incorrectly stops the queue.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The mac_address should be set also when ht caps are disabled.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the standard ALIGN() macro instead of redefining similar macros.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The module forgot to sometimes unregister some resources.
This fixes Bug #22882.
[Patch updated to 2.6.38-rc3 by Randy Dunlap.]
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-2639-rc4/i2c-fixes' of git://git.fluff.org/bjdooks/linux:
i2c-omap: fixup commit cb527ede1b whitespace
i2c-omap: Double clear of ARDY status in IRQ handler
i2c-omap: fix build for !CONFIG_SUSPEND
i2c-omap: fix static suspend vs. runtime suspend
i2c-stu300: make sure adapter-name is terminated
Functions that are not used outsde of the module they are defined
should be marked as static.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This errata occurs when the ARDY interrupt generation is enabled.
At the begining of every new transaction the ARDY interrupt is cleared.
On continuous i2c transactions where after clearing the ARDY bit from
I2C_STAT register (clearing the interrupt), the IRQ line is reasserted and the
I2C_STAT[ARDY] bit set again on 1. In fact, the ARDY status bit is not cleared
at the write access to I2C_STAT[ARDY] and only the IRQ line is deasserted and
then reasserted. This is not captured in the usual errata documents.
The workaround is to have a double clear of ARDY status in irq handler.
Signed-off-by: Richard woodruff <r-woodruff2@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Some userspaces can emit a whole packet without disabling AA resolve
by the looks of it, so we have to deal with them.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tested-by: Jorg Otte <jrg.otte@googlemail.com>
r100_gpu_init() was dropped in 90aca4d ("drm/radeon/kms: simplify &
improve GPU reset V2") but here it was only commented out.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Testing showed the current code can already handle doublescan
video modes just fine. A trivial tweak makes it work for interlaced
scanout as well.
Tested and shown to be precise on Radeon rv530, r600 and
Intel 945-GME.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Documentation/atomic_ops.txt tells us that there are memory
barriers optimized for atomic_inc and other atomic_t ops.
Use these instead of smp_wmb(), and also to make the required
memory barriers around vblank counter increments more explicit.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use of abs() wrongly wrapped diff_ns to 32 bit, which gives a 1/4000
probability of a missed vblank increment at each vblank irq reenable
if the kms driver doesn't support high precision vblank timestamping.
Not a big deal in practice, but let's make it nice.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
this aligns the height of the fb allocation so it doesn't trip
over the size checks later when we use this from userspace to
copy the buffer at X start.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit a6f9761743.
Remove this commit as it is no longer necessary. The relevant bugs
were fixed properly in:
drm/radeon/kms: hopefully fix pll issues for real (v3)
5b40ddf888
drm/radeon/kms: add missing frac fb div flag for dce4+
9f4283f49f
This commit also broke certain ~5 Mhz modes on old arcade monitors,
so reverting this commit fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=29502
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
When runtime PM is enabled, each OMAP i2c device is suspended after
each i2c xfer. However, there are two cases when the static suspend
methods must be used to ensure the devices are suspended:
1) runtime PM is disabled, either at compile time or dynamically
via /sys/devices/.../power/control.
2) an i2c client driver uses i2c during it's suspend callback, thus
leaving the i2c driver active (NOTE: runtime suspend transitions are
disabled during system suspend, so i2c activity during system
suspend will runtime resume the device, but not runtime (re)suspend it.)
Since the actual work to suspend the device is handled by the
subsytem, call the bus methods to take care of it.
NOTE: This takes care of a known suspend problem on OMAP3 where the
TWL RTC driver does i2c xfers during its suspend path leaving the i2c
driver in an active state (since runtime suspend transistions are
disabled.)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use strlcpy instead of strncpy.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use hba_port_num for phy loopback and ethtool phy identification.
From: Suresh R <suresh.reddy@emulex.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emil Tantilov
Alexander Duyck
Greg Rose
Carolyn Wyborny
Stefan Assmann
Dimitris Michailidis
Linus Torvalds
Michael Chan
David S. Miller
Andres Salomon
Michal Simek
Jarod Wilson
Devin Heitmueller
Michael
Sven Barth
Andy Walls
Olivier Grenie
Antti Seppälä
Tejun Heo
Bruce Allan
Jeff Kirsher
Stephen Hemminger
vwadekar@nvidia.com
Mark Brown
Manjunathappa, Prakash
Jochen Friedrich
Lennert Buytenhek
Jiri Slaby
Jan Niehusmann
Rafał Miłecki
Chaoming Li
Sujith Manoharan
Hayes Wang
Rafael J. Wysocki
Ben Hutchings
Steve Hodgson
Amerigo Wang
Hegde, Vinay
Dmitry Kravkov
Vladislav Zolotarov
Roopa Prabhu
Ben Dooks
Rémi Denis-Courmont
Axel Lin
Sergei Shtylyov
Ilya Yanok
Jamie Iles
Shmulik Ravid
Kurt Van Dijck
Justin Mattock
Ken Kawasaki
Stanislaw Gruszka
Senthil Balasubramanian
Felix Fietkau
Alessio Igor Bogani
Dan Carpenter
John W. Linville
Christian Lamparter
Jiri Pirko
Dave Airlie
Ben Skeggs
Dmitry Eremin-Solenikov
Ursula Braun
Wey-Yi Guy
Alexandre Bounine
Alexander Gordeev
Lei Xu
Matti J. Aaltonen
Jelle Martijn Kok
Vivek Natarajan
Johannes Berg
Joe Gunn
Jussi Kivilinna
Jan Puk
Jesper Juhl
Stephen Hemminger
Felipe Balbi
Vasiliy Kulikov
Chris Wilson
Lior Levy
NeilBrown
Daniel Vetter
Shahar Havivi
Henry Nestler
Rajesh Borundia
amit salecha
Florian Fainelli
Shawn Lin
Larry Finger
Willy Tarreau
Nishant Sarmukadam
Dmitry Torokhov
Arik Nemtsov
Eliad Peller
Florian Mickler
Dmitry Torokhov
Richard woodruff
Balaji T K
Paul Bolle
Mario Kleiner
Alex Deucher
Kevin Hilman
Wolfram Sang
Ajit Khaparde