Граф коммитов

7 Коммитов

Автор SHA1 Сообщение Дата
Andreas Noever ca389f716f thunderbolt: Enable plug events
Thunderbolt switches have a plug events capability. This patch adds the
tb_plug_events_active method and uses it to activate plug events during
switch allocation.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-19 14:07:47 -07:00
Andreas Noever e2b8785ed3 thunderbolt: Add thunderbolt capability handling
Thunderbolt config areas contain capability lists similar to those found
on pci devices. This patch introduces a tb_find_cap utility method to
search for capabilities.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-19 14:07:47 -07:00
Andreas Noever a25c8b2fc9 thunderbolt: Initialize root switch and ports
This patch adds the structures tb_switch and tb_port as well as code to
initialize the root switch.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-19 14:07:08 -07:00
Andreas Noever 7adf60972c thunderbolt: Add tb_regs.h
Every thunderbolt device consists (logically) of a switch with multiple
ports. Every port contains up to four config regions (HOPS, PORT,
SWITCH, COUNTERS) which are used to configure the device.

The tb_regs.h file contains all known registers and capabilities from
these config regions.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-19 14:07:07 -07:00
Andreas Noever d6cc51cd1a thunderbolt: Setup control channel
Add struct tb which will contain our view of the thunderbolt bus.  For
now it just contains a pointer to the control channel and a workqueue
for hotplug events.

Add thunderbolt_alloc_and_start() and thunderbolt_shutdown_and_free()
which are responsible for setup and teardown of struct tb.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-19 14:07:07 -07:00
Andreas Noever f25bf6fcb1 thunderbolt: Add control channel interface
Thunderbolt devices are configured by reading/writing into their
configuration space (similar to pci). This is done by sending packets
through the NHI (native host interface) onto the control channel.

This patch handles the low level packet based protocol and exposes
higher level operations like tb_cfg_read/tb_cfg_write.

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-19 14:07:07 -07:00
Andreas Noever 1660315366 thunderbolt: Add initial cactus ridge NHI support
Thunderbolt hotplug is supposed to be handled by the firmware. But Apple
decided to implement thunderbolt at the operating system level. The
firmare only initializes thunderbolt devices that are present at boot
time. This driver enables hotplug of thunderbolt of non-chained
thunderbolt devices on Apple systems with a cactus ridge controller.

This first patch adds the Kconfig file as well the parts of the driver
which talk directly to the hardware (that is pci device setup, interrupt
handling and RX/TX ring management).

Signed-off-by: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-06-19 14:04:52 -07:00