Граф коммитов

3 Коммитов

Автор SHA1 Сообщение Дата
Nikolay Aleksandrov e19b42a1a0 bridge: netlink: make setlink/dellink notifications more accurate
Before this patch we had cases that either sent notifications when there
were in fact no changes (e.g. non-existent vlan delete) or didn't send
notifications when there were changes (e.g. vlan add range with an error in
the middle, port flags change + vlan update error). This patch sends down
a boolean to the functions setlink/dellink use and if there is even a
single configuration change (port flag, vlan add/del, port state) then
we always send a notification. This is all done to keep backwards
compatibility with the opportunistic vlan delete, where one could
specify a vlan range that has missing vlans inside and still everything
in that range will be cleared, this is mostly used to clear the whole
vlan config with a single call, i.e. range 1-4094.

Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-29 11:03:43 +09:00
Roopa Prabhu 11538d039a bridge: vlan dst_metadata hooks in ingress and egress paths
- ingress hook:
    - if port is a tunnel port, use tunnel info in
      attached dst_metadata to map it to a local vlan
- egress hook:
    - if port is a tunnel port, use tunnel info attached to
      vlan to set dst_metadata on the skb

CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-03 15:21:22 -05:00
Roopa Prabhu efa5356b0d bridge: per vlan dst_metadata netlink support
This patch adds support to attach per vlan tunnel info dst
metadata. This enables bridge driver to map vlan to tunnel_info
at ingress and egress. It uses the kernel dst_metadata infrastructure.

The initial use case is vlan to vni bridging, but the api is generic
to extend to any tunnel_info in the future:
    - Uapi to configure/unconfigure/dump per vlan tunnel data
    - netlink functions to configure vlan and tunnel_info mapping
    - Introduces bridge port flag BR_LWT_VLAN to enable attach/detach
    dst_metadata to bridged packets on ports. off by default.
    - changes to existing code is mainly refactor some existing vlan
    handling netlink code + hooks for new vlan tunnel code
    - I have kept the vlan tunnel code isolated in separate files.
    - most of the netlink vlan tunnel code is handling of vlan-tunid
    ranges (follows the vlan range handling code). To conserve space
    vlan-tunid by default are always dumped in ranges if applicable.

Use case:
example use for this is a vxlan bridging gateway or vtep
which maps vlans to vn-segments (or vnis).

iproute2 example (patched and pruned iproute2 output to just show
relevant fdb entries):
example shows same host mac learnt on two vni's and
vlan 100 maps to vni 1000, vlan 101 maps to vni 1001

before (netdev per vni):
$bridge fdb show | grep "00:02:00:00:00:03"
00:02:00:00:00:03 dev vxlan1001 vlan 101 master bridge
00:02:00:00:00:03 dev vxlan1001 dst 12.0.0.8 self
00:02:00:00:00:03 dev vxlan1000 vlan 100 master bridge
00:02:00:00:00:03 dev vxlan1000 dst 12.0.0.8 self

after this patch with collect metdata in bridged mode (single netdev):
$bridge fdb show | grep "00:02:00:00:00:03"
00:02:00:00:00:03 dev vxlan0 vlan 101 master bridge
00:02:00:00:00:03 dev vxlan0 src_vni 1001 dst 12.0.0.8 self
00:02:00:00:00:03 dev vxlan0 vlan 100 master bridge
00:02:00:00:00:03 dev vxlan0 src_vni 1000 dst 12.0.0.8 self

CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-03 15:21:22 -05:00