'struct dmi_system_id' arrays must always have a terminator to keep
dmi_check_system() from looking at data (and possibly crashing) it
isn't supposed to look at.
The issue went unnoticed until ef8313bb1a,
but was introduced about a year earlier with
7705d548cb (which also similarly changed
lifebook.c, but the problem there got eliminated shortly afterwards).
The first hunk therefore is a stable candidate back to 2.6.33, while
the full change is needed only on 2.6.38.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch add multitouch support for the MacBookPro8,1 and
MacBookPro8,2 models.
Cc: stable@kernel.org
Signed-off-by: Andy Botting <andy@andybotting.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With the current code, pressing the integrated button with an
isolating tool does not result in any button report. Fixed
with this this patch.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since Synaptics technical writers department is a bit slow releasing updated
Synaptics interface guide, let's add some new bits (with their blessing)
to the code so that they don't get lost.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move to convert drivers to dev_pm_ops rather than bus
specific PM ops in order to facilitate core development. Do this converison
for synaptics-i2c.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On some machines, like Dell Studio XPS 16 (1640), touchpad fails to
respond to the standard query after first reset but may start
responding later, so let's repeat reset sequence several (3) times.
Signed-off-by: Alexandre Peixoto Ferreira <alexandref75@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
synaptics_set_advanced_gesture_mode() affect capabilities bits we should
perform comparison after calling this function, otherwise they will never
match and we will be forced to perform full reconnect.
Signed-off-by: Alexandre Peixoto Ferreira <alexandref75@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (34 commits)
HID: roccat: Update sysfs attribute doc
HID: roccat: don't use #pragma pack
HID: roccat: Add support for Roccat Kone[+] v2
HID: roccat: reduce number of functions in kone and pyra drivers
HID: roccat: declare meaning of pack pragma usage in driver headers
HID: roccat: use class for char device for sysfs attribute creation
sysfs: Introducing binary attributes for struct class
HID: hidraw: add compatibility ioctl() for 32-bit applications.
HID: hid-picolcd: Fix memory leak in picolcd_debug_out_report()
HID: picolcd: fix misuse of logical operation in place of bitop
HID: usbhid: base runtime PM on modern API
HID: replace offsets values with their corresponding BTN_* defines
HID: hid-mosart: support suspend/resume
HID: hid-mosart: ignore buttons report
HID: hid-picolcd: don't use flush_scheduled_work()
HID: simplify an index check in hid_lookup_collection
HID: Hoist assigns from ifs
HID: Remove superfluous __inline__
HID: Use vzalloc for vmalloc/memset(,0...)
HID: Add and use hid_<level>: dev_<level> equivalents
...
OLPC has switched to a Synaptics touchpad. It turns out that it's
pretty useless in absolute mode. This patch looks for an OLPC
system (via DMI tables), and refuses to init Synaptics mode in
that scenario (falling back to relative mode).
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Minor comment fixup for typos and grammar. Noticed while adding a
separate workaround.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In multitouch mode, at least one device (fw: 7.4 id: 0x1c0b1) sometimes
sends a final main packet with x == 1. Since the normal values are above
1472, this is clearly bogus. At the same time, a two-finger touch is
signaled, even though only one finger was on the pad to begin with. This
patch ignores the packet altogether, removing the problem.
Acked-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
The Synaptics 2.7 series of touchpads support a mode for reporting two
sets of X/Y/Pressure data (advanced gesture mode). By default, these
devices report only single finger data, depriving userspace of the
nowadays ubiquitous two-finger scroll gesture.
Enabling advanced gesture mode also enables the multi-finger report,
although the device does not claim that capability. Up to three
fingers can be reported this way.
While two or three fingers are touching, the normal packet is
prepended by a reduced finger packet of lower resolution. From the two
packets (which do not represent the actual fingers), the bounding
rectangle of the individual contacts can be extracted. This
information is sufficient to perform scaling gestures and a limited
form of rotation gesture. The behavior has been coined semi-mt
capability, and is signaled to userspace via the INPUT_PROP_SEMI_MT
device property.
Work to decode the advanced gesture packet: Takashi Iwai.
Cleanup and testing of the original patch: Chase Douglas.
Minor cleanup and testing: Chris Bagwell.
Finalization and semi-mt support: Henrik Rydberg.
Reported-by: Tobyn Bertram
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
With the new input property interface, it is possible to report the
special quirks of a device using ioctl/sysfs. This patch sets up the
device as a pointer, and reports the clickpad functionality via the
INPUT_PROP_BUTTONPAD property.
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Lenovo S10-3t's ClickPad is a 2-button ClickPad that reports BTN_LEFT
and BTN_RIGHT as normal touchpad, unlike the 1-button ClickPad used in
HP mini 210 that reports solely BTN_MIDDLE.
In 0xc0-cap response, the 1-button ClickPad has the 20-bit set while
2-button ClickPad has the 8-bit set.
This patch makes the kernel only handle 1-button ClickPad specially,
and treat 2-button ClickPad in the same fashion as regular touchpads.
This fixes kernel bug #18122 and MeeGo bug #4807.
Signed-off-by: Yan Li <yan.i.li@intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds support for the MacBookAir3,1 and MacBookAir3,2
models.
[rydberg@euromail.se: touchpad range calibration]
Cc: stable@kernel.org
Signed-off-by: Edgar (gimli) Hucek <gimli@dark-green.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Recent testing of this codepath showed that it wasn't working,
perhaps due to changes within the input layer. This fixes it.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Disable the recalibration guard where new recalibrations are triggered
if we detect a packet too soon after calibrating - we found that this
results in erroneous recalibrations, and if the recalibration failed
then the rest of our badness-detection code will request another.
Add a module option disabling all of the recalibration code, in case
an OLPC deployment thinks all of the workarounds we have are doing
more damage than good and wants to experiment with them all disabled.
Based on work by Paul Fox.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In addition to forcing recalibrations upon detection of cursor jumps (and
performing them quicker than before), detect and discard errant 'jump'
packets caused by a firmware bug, which are then repeated with each one
being approximately half the delta of the one previously (as if it is
averaging out)
Based on original work by Paul Fox.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The old implementation of spew detection simply tracked the overall
position delta of the cursor over every 100 packets. We found that
this causes occasional false positives in spew detection, and also
that the conditions of the spewy packets are perhaps more fixed than
we once thought.
Rework the spew detection to look for packets of specific small
delta, and only recalibrating if the overall movement delta stays
within expected bounds.
Also discard duplicate packets in the advanced mode, which appear
to be very common. If we don't, the spew detection kicks in far
too early. If we get a large spew of duplicates, request a
recalibration straight up.
Based on earlier work by Paul Fox.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a "hgpk_mode" sysfs attribute that allows selection between 3 options:
Mouse (the existing option), GlideSensor and PenTablet.
GlideSensor is an enhanced protocol for the regular touchpad mode that
additionally reports pressure and uses absolute coordinates. We suspect
that it may be more reliable than mouse mode in some environments.
PenTablet mode puts the touchpad into resistive mode, you must then use
a stylus as an input. We suspect this is the most reliable way to drive
the touchpad.
The GlideSensor and PenTablet devices expose themselves with the
intention of being combined with the synaptics X11 input driver.
Based on earlier work by Paul Fox.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: appletouch - remove extra KERN_DEBUG use from dprintk
Input: bu21013_ts - fix null dereference in error handling
Input: ad7879 - prevent invalid finger data reports
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some (rare) serio devices need to have multiple serio children. One of
the examples is PS/2 multiplexer present on several TQC STKxxx boards,
which connect PS/2 keyboard and mouse to single tty port.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
By visual inspection, the reported touch_major and touch_minor axes
are a factor of two too small. Presumably the device actually reports
the semi-major and semi-minor axes. Corrected with this patch.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is more kernel-ish, saves some space, and also allows us to
expand the ops without breaking all the callers who are happy for the
new members to be NULL.
The few places which defined their own param types are changed to the
new scheme (more which crept in recently fixed in following patches).
Since we're touching them anyway, we change get() and set() to take a
const struct kernel_param (which they really are). This causes some
harmless warnings until we fix them (in following patches).
To reduce churn, module_param_call creates the ops struct so the callers
don't have to change (and casts the functions to reduce warnings).
The modern version which takes an ops struct is called module_param_cb.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Alessandro Rubini <rubini@ipvvis.unipv.it>
Cc: Michal Januszewski <spock@gentoo.org>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-fbdev-devel@lists.sourceforge.net
Cc: linux-nfs@vger.kernel.org
Cc: netdev@vger.kernel.org
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - add USB-ID for PL-3601 Xbox 360 pad
Input: cy8ctmg100_ts - signedness bug
Input: elantech - report position also with 3 fingers
Input: elantech - discard the first 2 positions on some firmwares
Input: adxl34x - do not mark device as disabled on startup
Input: gpio_keys - add hooks to enable/disable device
Input: evdev - rearrange ioctl handling
Input: dynamically allocate ABS information
Input: switch to input_abs_*() access functions
Input: add static inline accessors for ABS properties
This reverts commit 04b4b88cca.
While the original problem only caused a slight disturbance on the
edge of the touchpad, the commit above to "fix" it completely breaks
operation on some other models such as mine.
We'll sort this out separately, revert the patch for now.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The 6-byte protocol supports reporting the position when three fingers
are pressed, exactly like when one finger is pressed. Report this.
In addition, it is also distinguishes between 3 and 4 fingers pressed.
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
According to the Dell/Ubuntu driver, what was previously observed as
"jumpy cursor" corresponds to the hardware sending incorrect data for
the first two reports of a one touch finger. So let's use the same
workaround as in the other driver. Also, detect another firmware
version with the same behaviour, as in the other driver.
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
Input: adp5588-keypad - fix NULL dereference in adp5588_gpio_add()
Input: cy8ctmg110 - capacitive touchscreen support
Input: keyboard - also match braille-only keyboards
Input: adp5588-keys - export unused GPIO pins
Input: xpad - add product ID for Hori Fighting Stick EX2
Input: adxl34x - fix leak and use after free
Input: samsung-keypad - Add samsung keypad driver
Input: i8042 - reset keyboard controller wehen resuming from S2R
Input: synaptics - set min/max for finger width
Input: synaptics - only report width on hardware that supports it
Input: evdev - signal that device is writable in evdev_poll()
Input: mousedev - signal that device is writable in mousedev_poll()
Input: change input handlers to use bool when possible
Input: document the MT event slot protocol
Input: introduce MT event slots
Input: usbtouchscreen - implement reset_resume
Input: usbtouchscreen - implement runtime power management
Input: usbtouchscreen - implement basic suspend/resume
Input: Add ATMEL QT602240 touchscreen driver
Input: fix signedness warning in input_set_keycode()
...
Change all call sites in drivers/input to not access the ABS axis
information directly anymore. Make them use the access helpers instead.
Also use input_set_abs_params() when possible.
Did some code refactoring as I was on it.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - relax capability ID checks on newer hardware
Input: twl40300-keypad - fix handling of "all ground" rows
Input: gamecon - reference correct pad in gc_psx_command()
Input: gamecon - reference correct input device in NES mode
Input: w90p910_keypad - change platfrom driver name to 'nuc900-kpi'
Input: i8042 - add Gigabyte Spring Peak to dmi_noloop_table
Input: qt2160 - rename kconfig symbol name
Older firmwares fixed the middle byte of the Synaptics capabilities
query to 0x47, but starting with firmware 7.5 the middle byte
represents submodel ID, sometimes also called "dash number".
Reported-and-tested-by: Miroslav Šulc <fordfrog@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Linus Torvalds
Lucas De Marchi
Jan Beulich
Dmitry Torokhov
Andy Botting
Henrik Rydberg
Mark Brown
Alexandre Peixoto Ferreira
David Rientjes
Andres Salomon
Jiri Kosina
Yan Li
Edgar (gimli) Hucek
Paul Fox
Daniel Drake
Joe Perches
Justin P. Mattock
Dmitry Eremin-Solenikov
Davidlohr Bueso
Rusty Russell
Benjamin Herrenschmidt
Éric Piel
Daniel Mack