Граф коммитов

13 Коммитов

Автор SHA1 Сообщение Дата
Ming Lei 544fbd16a4 block: deactivate blk_stat timer in wbt_disable_default()
rwb_enabled() can't be changed when there is any inflight IO.

wbt_disable_default() may set rwb->wb_normal as zero, however the
blk_stat timer may still be pending, and the timer function will update
wrb->wb_normal again.

This patch introduces blk_stat_deactivate() and applies it in
wbt_disable_default(), then the following IO hang triggered when running
parted & switching io scheduler can be fixed:

[  369.937806] INFO: task parted:3645 blocked for more than 120 seconds.
[  369.938941]       Not tainted 4.20.0-rc6-00284-g906c801e5248 #498
[  369.939797] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[  369.940768] parted          D    0  3645   3239 0x00000000
[  369.941500] Call Trace:
[  369.941874]  ? __schedule+0x6d9/0x74c
[  369.942392]  ? wbt_done+0x5e/0x5e
[  369.942864]  ? wbt_cleanup_cb+0x16/0x16
[  369.943404]  ? wbt_done+0x5e/0x5e
[  369.943874]  schedule+0x67/0x78
[  369.944298]  io_schedule+0x12/0x33
[  369.944771]  rq_qos_wait+0xb5/0x119
[  369.945193]  ? karma_partition+0x1c2/0x1c2
[  369.945691]  ? wbt_cleanup_cb+0x16/0x16
[  369.946151]  wbt_wait+0x85/0xb6
[  369.946540]  __rq_qos_throttle+0x23/0x2f
[  369.947014]  blk_mq_make_request+0xe6/0x40a
[  369.947518]  generic_make_request+0x192/0x2fe
[  369.948042]  ? submit_bio+0x103/0x11f
[  369.948486]  ? __radix_tree_lookup+0x35/0xb5
[  369.949011]  submit_bio+0x103/0x11f
[  369.949436]  ? blkg_lookup_slowpath+0x25/0x44
[  369.949962]  submit_bio_wait+0x53/0x7f
[  369.950469]  blkdev_issue_flush+0x8a/0xae
[  369.951032]  blkdev_fsync+0x2f/0x3a
[  369.951502]  do_fsync+0x2e/0x47
[  369.951887]  __x64_sys_fsync+0x10/0x13
[  369.952374]  do_syscall_64+0x89/0x149
[  369.952819]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  369.953492] RIP: 0033:0x7f95a1e729d4
[  369.953996] Code: Bad RIP value.
[  369.954456] RSP: 002b:00007ffdb570dd48 EFLAGS: 00000246 ORIG_RAX: 000000000000004a
[  369.955506] RAX: ffffffffffffffda RBX: 000055c2139c6be0 RCX: 00007f95a1e729d4
[  369.956389] RDX: 0000000000000001 RSI: 0000000000001261 RDI: 0000000000000004
[  369.957325] RBP: 0000000000000002 R08: 0000000000000000 R09: 000055c2139c6ce0
[  369.958199] R10: 0000000000000000 R11: 0000000000000246 R12: 000055c2139c0380
[  369.959143] R13: 0000000000000004 R14: 0000000000000100 R15: 0000000000000008

Cc: stable@vger.kernel.org
Cc: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-12-12 06:47:51 -07:00
Josef Bacik 2ecbf45635 blk-stat: export helpers for modifying blk_rq_stat
We need to use blk_rq_stat in the blkcg qos stuff, so export some of
these helpers so they can be used by other things.

Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-07-09 09:07:54 -06:00
Omar Sandoval 522a777566 block: consolidate struct request timestamp fields
Currently, struct request has four timestamp fields:

- A start time, set at get_request time, in jiffies, used for iostats
- An I/O start time, set at start_request time, in ktime nanoseconds,
  used for blk-stats (i.e., wbt, kyber, hybrid polling)
- Another start time and another I/O start time, used for cfq and bfq

These can all be consolidated into one start time and one I/O start
time, both in ktime nanoseconds, shaving off up to 16 bytes from struct
request depending on the kernel config.

Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-05-09 08:33:09 -06:00
Omar Sandoval 544ccc8dc9 block: get rid of struct blk_issue_stat
struct blk_issue_stat squashes three things into one u64:

- The time the driver started working on a request
- The original size of the request (for the io.low controller)
- Flags for writeback throttling

It turns out that on x86_64, we have a 4 byte hole in struct request
which we can fill with the non-timestamp fields from blk_issue_stat,
simplifying things quite a bit.

Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-05-09 08:33:05 -06:00
Jens Axboe 782f569774 blk-wbt: throttle discards like background writes
Throttle discards like we would any background write. Discards should
be background activity, so if they are impacting foreground IO, then
we will throttle them down.

Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-05-08 15:11:02 -06:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Jens Axboe 99c749a4c4 blk-stat: kill blk_stat_rq_ddir()
No point in providing and exporting this helper. There's just
one (real) user of it, just use rq_data_dir().

Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-21 07:56:23 -06:00
Stephen Bates a37244e4cc blk-stat: convert blk-stat bucket callback to signed
In order to allow for filtering of IO based on some other properties
of the request than direction we allow the bucket function to return
an int.

If the bucket callback returns a negative do no count it in the stats
accumulation.

Signed-off-by: Stephen Bates <sbates@raithlin.com>

Fixed up Kyber scheduler stat callback.

Signed-off-by: Jens Axboe <axboe@fb.com>
2017-04-20 15:29:16 -06:00
Shaohua Li b9147dd1ba blk-throttle: add a mechanism to estimate IO latency
User configures latency target, but the latency threshold for each
request size isn't fixed. For a SSD, the IO latency highly depends on
request size. To calculate latency threshold, we sample some data, eg,
average latency for request size 4k, 8k, 16k, 32k .. 1M. The latency
threshold of each request size will be the sample latency (I'll call it
base latency) plus latency target. For example, the base latency for
request size 4k is 80us and user configures latency target 60us. The 4k
latency threshold will be 80 + 60 = 140us.

To sample data, we calculate the order base 2 of rounded up IO sectors.
If the IO size is bigger than 1M, it will be accounted as 1M. Since the
calculation does round up, the base latency will be slightly smaller
than actual value. Also if there isn't any IO dispatched for a specific
IO size, we will use the base latency of smaller IO size for this IO
size.

But we shouldn't sample data at any time. The base latency is supposed
to be latency where disk isn't congested, because we use latency
threshold to schedule IOs between cgroups. If disk is congested, the
latency is higher, using it for scheduling is meaningless. Hence we only
do the sampling when block throttling is in the LOW limit, with
assumption disk isn't congested in such state. If the assumption isn't
true, eg, low limit is too high, calculated latency threshold will be
higher.

Hard disk is completely different. Latency depends on spindle seek
instead of request size. Currently this feature is SSD only, we probably
can use a fixed threshold like 4ms for hard disk though.

Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-03-28 08:02:20 -06:00
Shaohua Li 88eeca495b block: track request size in blk_issue_stat
Currently there is no way to know the request size when the request is
finished. Next patch will need this info. We could add extra field to
record the size, but blk_issue_stat has enough space to record it, so
this patch just overloads blk_issue_stat. With this, we will have 49bits
to track time, which still is very long time.

Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-03-28 08:02:20 -06:00
Omar Sandoval 34dbad5d26 blk-stat: convert to callback-based statistics reporting
Currently, statistics are gathered in ~0.13s windows, and users grab the
statistics whenever they need them. This is not ideal for both in-tree
users:

1. Writeback throttling wants its own dynamically sized window of
   statistics. Since the blk-stats statistics are reset after every
   window and the wbt windows don't line up with the blk-stats windows,
   wbt doesn't see every I/O.
2. Polling currently grabs the statistics on every I/O. Again, depending
   on how the window lines up, we may miss some I/Os. It's also
   unnecessary overhead to get the statistics on every I/O; the hybrid
   polling heuristic would be just as happy with the statistics from the
   previous full window.

This reworks the blk-stats infrastructure to be callback-based: users
register a callback that they want called at a given time with all of
the statistics from the window during which the callback was active.
Users can dynamically bucketize the statistics. wbt and polling both
currently use read vs. write, but polling can be extended to further
subdivide based on request size.

The callbacks are kept on an RCU list, and each callback has percpu
stats buffers. There will only be a few users, so the overhead on the
I/O completion side is low. The stats flushing is also simplified
considerably: since the timer function is responsible for clearing the
statistics, we don't have to worry about stale statistics.

wbt is a trivial conversion. After the conversion, the windowing problem
mentioned above is fixed.

For polling, we register an extra callback that caches the previous
window's statistics in the struct request_queue for the hybrid polling
heuristic to use.

Since we no longer have a single stats buffer for the request queue,
this also removes the sysfs and debugfs stats entries. To replace those,
we add a debugfs entry for the poll statistics.

Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-03-21 10:03:11 -06:00
Omar Sandoval fa2e39cb9e blk-stat: use READ and WRITE instead of BLK_STAT_{READ,WRITE}
The stats buckets will become generic soon, so make the existing users
use the common READ and WRITE definitions instead of one internal to
blk-stat.

Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
2017-03-21 10:03:08 -06:00
Jens Axboe cf43e6be86 block: add scalable completion tracking of requests
For legacy block, we simply track them in the request queue. For
blk-mq, we track them on a per-sw queue basis, which we can then
sum up through the hardware queues and finally to a per device
state.

The stats are tracked in, roughly, 0.1s interval windows.

Add sysfs files to display the stats.

The feature is off by default, to avoid any extra overhead. In-kernel
users of it can turn it on by setting QUEUE_FLAG_STATS in the queue
flags. We currently don't turn it on if someone just reads any of
the stats files, that is something we could add as well.

Signed-off-by: Jens Axboe <axboe@fb.com>
2016-11-10 13:53:26 -07:00