commit 2061ecfdf2 upstream.
If packet headers changed, the cached nfct is no longer relevant
for the packet and attempt to re-use it leads to the incorrect packet
classification.
This issue is causing broken connectivity in OpenStack deployments
with OVS/OVN due to hairpin traffic being unexpectedly dropped.
The setup has datapath flows with several conntrack actions and tuple
changes between them:
actions:ct(commit,zone=8,mark=0/0x1,nat(src)),
set(eth(src=00:00:00:00:00:01,dst=00:00:00:00:00:06)),
set(ipv4(src=172.18.2.10,dst=192.168.100.6,ttl=62)),
ct(zone=8),recirc(0x4)
After the first ct() action the packet headers are almost fully
re-written. The next ct() tries to re-use the existing nfct entry
and marks the packet as invalid, so it gets dropped later in the
pipeline.
Clearing the cached conntrack entry whenever packet tuple is changed
to avoid the issue.
The flow key should not be cleared though, because we should still
be able to match on the ct_state if the recirculation happens after
the tuple change but before the next ct() action.
Cc: stable@vger.kernel.org
Fixes: 7f8a436eaa ("openvswitch: Add conntrack action")
Reported-by: Frode Nordahl <frode.nordahl@canonical.com>
Link: https://mail.openvswitch.org/pipermail/ovs-discuss/2022-May/051829.html
Link: https://bugs.launchpad.net/ubuntu/+source/ovn/+bug/1967856
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Link: https://lore.kernel.org/r/20220606221140.488984-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c76acfb7e1 upstream.
There is a limitation in TI DP83867 PHY device where SGMII AN is only
triggered once after the device is booted up. Even after the PHY TPI is
down and up again, SGMII AN is not triggered and hence no new in-band
message from PHY to MAC side SGMII.
This could cause an issue during power up, when PHY is up prior to MAC.
At this condition, once MAC side SGMII is up, MAC side SGMII wouldn`t
receive new in-band message from TI PHY with correct link status, speed
and duplex info.
As suggested by TI, implemented a SW solution here to retrigger SGMII
Auto-Neg whenever there is a link change.
v2: Add Fixes tag in commit message.
Fixes: 2a10154abc ("net: phy: dp83867: Add TI dp83867 phy")
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: Sit, Michael Wei Hong <michael.wei.hong.sit@intel.com>
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220526090347.128742-1-tee.min.tan@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a051246b78 upstream.
The intention of the use of mmc_blk_reset_success() in
mmc_blk_cqe_recovery() was to prevent repeated resets when retrying and
getting the same error. However, that may not be the case - any amount
of time and I/O may pass before another recovery is needed, in which
case there would be no reason to deny it the opportunity to recover via
a reset if necessary. CQE recovery is expected seldom and failure to
recover (if the clear tasks command fails), even more seldom, so it is
better to allow the reset always, which can be done by calling
mmc_blk_reset_success() always.
Fixes: 1e8e55b670 ("mmc: block: Add CQE support")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220531171922.76080-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72aad489f9 upstream.
The {dma|pio}_mode sysfs files are incorrectly documented as having a
list of the supported DMA/PIO transfer modes, while the corresponding
fields of the *struct* ata_device hold the transfer mode IDs, not masks.
To match these docs, the {dma|pio}_mode (and even xfer_mode!) sysfs
files are handled by the ata_bitfield_name_match() macro which leads to
reading such kind of nonsense from them:
$ cat /sys/class/ata_device/dev3.0/pio_mode
XFER_UDMA_7, XFER_UDMA_6, XFER_UDMA_5, XFER_UDMA_4, XFER_MW_DMA_4,
XFER_PIO_6, XFER_PIO_5, XFER_PIO_4, XFER_PIO_3, XFER_PIO_2, XFER_PIO_1,
XFER_PIO_0
Using the correct ata_bitfield_name_search() macro fixes that:
$ cat /sys/class/ata_device/dev3.0/pio_mode
XFER_PIO_4
While fixing the file documentation, somewhat reword the {dma|pio}_mode
file doc and add a note about being mostly useful for PATA devices to
the xfer_mode file doc...
Fixes: d9027470b8 ("[libata] Add ATA transport class")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dda5384313 upstream.
When creating (sealing) a new trusted key, migratable
trusted keys have the FIXED_TPM and FIXED_PARENT attributes
set, and non-migratable keys don't. This is backwards, and
also causes creation to fail when creating a migratable key
under a migratable parent. (The TPM thinks you are trying to
seal a non-migratable blob under a migratable parent.)
The following simple patch fixes the logic, and has been
tested for all four combinations of migratable and non-migratable
trusted keys and parent storage keys. With this logic, you will
get a proper failure if you try to create a non-migratable
trusted key under a migratable parent storage key, and all other
combinations work correctly.
Cc: stable@vger.kernel.org # v5.13+
Fixes: e5fb5d2c5a ("security: keys: trusted: Make sealed key properly interoperable")
Signed-off-by: David Safford <david.safford@gmail.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c36ee7dab7 upstream.
cifs.ko defines two file system types: cifs & smb3, and
__cifs_get_super() was not including smb3 file system type when
looking up superblocks, therefore failing to reconnect tcons in
cifs_tree_connect().
Fix this by calling iterate_supers_type() on both file system types.
Link: https://lore.kernel.org/r/CAFrh3J9soC36+BVuwHB=g9z_KB5Og2+p2_W+BBoBOZveErz14w@mail.gmail.com
Cc: stable@vger.kernel.org
Tested-by: Satadru Pramanik <satadru@gmail.com>
Reported-by: Satadru Pramanik <satadru@gmail.com>
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ea21823aa upstream.
During reconnects, we check the return value from
cifs_negotiate_protocol, and have handlers for both success
and failures. But if that passes, and cifs_setup_session
returns any errors other than -EACCES, we do not handle
that. This fix adds a handler for that, so that we don't
go ahead and try a tree_connect on a failed session.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Reviewed-by: Enzo Matsumiya <ematsumiya@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f3d696eea upstream.
Enables the audio mute LEDs and limits the mic boost to avoid picking up
noise.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220608140111.23170-1-tcrawford@system76.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0469d6581 upstream.
Focusrite Saffire 6 has fixed audioformat quirks with multiple
endpoints assigned to a single altsetting. Unfortunately the generic
parser couldn't detect the sync endpoint correctly as the implicit
sync due to the missing EP attribute bits. In the former kernels, it
used to work somehow casually, but it's been broken for a while after
the large code change in 5.11.
This patch cures the regression by the following:
- Allow the static quirk table to provide the sync EP information;
we just need to fill the fields and let the generic parser skipping
parsing if sync_ep is already set.
- Add the sync endpoint information to the entry for Saffire 6.
Fixes: 7b0efea4ba ("ALSA: usb-audio: Add missing ep_idx in fixed EP quirks")
Reported-and-tested-by: André Kapelrud <a.kapelrud@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220606160910.6926-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efb75df105 upstream.
When ep_idx is already non-zero, it means usually a capture stream
that is set up explicity by a fixed-format quirk, and applying the
check for generic (non-implicit-fb) sync EPs might hit incorrectly,
resulting in a bogus sync endpoint for the capture stream.
This patch adds a check for the ep_idx and skip if it's a secondary
endpoint. It's a part of the fixes for regressions on Saffire 6.
Fixes: 7b0efea4ba ("ALSA: usb-audio: Add missing ep_idx in fixed EP quirks")
Reported-and-tested-by: André Kapelrud <a.kapelrud@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220606160910.6926-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f7a6cf6b0 ]
MAGIC_START("IKCFG_ST") and MAGIC_END("IKCFG_ED") are moved out
from the kernel_config_data variable.
Thus, we parse kernel_config_data directly instead of considering
offset of MAGIC_START and MAGIC_END.
Fixes: 13610aa908 ("kernel/configs: use .incbin directive to embed config_data.gz")
Signed-off-by: Kuan-Ying Lee <Kuan-Ying.Lee@mediatek.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dbd29e0752 ]
We should use size of descriptor chain to test loop condition
in the indirect case. And another statistical count is also introduced
for indirect descriptors to avoid conflict with the statistical count
of direct descriptors.
Fixes: f87d0fbb57 ("vringh: host-side implementation of virtio rings.")
Signed-off-by: Xie Yongji <xieyongji@bytedance.com>
Signed-off-by: Fam Zheng <fam.zheng@bytedance.com>
Message-Id: <20220505100910.137-1-xieyongji@bytedance.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dfe54071d ]
The nodemask routines had mixed return values that provided potentially
signed return values that could never happen. This was leading to the
compiler getting confusing about the range of possible return values
(it was thinking things could be negative where they could not be). Fix
all the nodemask routines that should be returning unsigned
(or bool) values. Silences:
mm/swapfile.c: In function ‘setup_swap_info’:
mm/swapfile.c:2291:47: error: array subscript -1 is below array bounds of ‘struct plist_node[]’ [-Werror=array-bounds]
2291 | p->avail_lists[i].prio = 1;
| ~~~~~~~~~~~~~~^~~
In file included from mm/swapfile.c:16:
./include/linux/swap.h:292:27: note: while referencing ‘avail_lists’
292 | struct plist_node avail_lists[]; /*
| ^~~~~~~~~~~
Reported-by: Christophe de Dinechin <dinechin@redhat.com>
Link: https://lore.kernel.org/lkml/20220414150855.2407137-3-dinechin@redhat.com/
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Yury Norov <yury.norov@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 525d651560 ]
The smu_v1X_0_set_allowed_mask() uses bitmap_copy() to convert
bitmap to 32-bit array. This may be wrong due to endiannes issues.
Fix it by switching to bitmap_{from,to}_arr32.
CC: Alexander Gordeev <agordeev@linux.ibm.com>
CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: Christian Borntraeger <borntraeger@linux.ibm.com>
CC: Claudio Imbrenda <imbrenda@linux.ibm.com>
CC: David Hildenbrand <david@redhat.com>
CC: Heiko Carstens <hca@linux.ibm.com>
CC: Janosch Frank <frankja@linux.ibm.com>
CC: Rasmus Villemoes <linux@rasmusvillemoes.dk>
CC: Sven Schnelle <svens@linux.ibm.com>
CC: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7ef93ffccd ]
We should not be including unused smb20 specific code when legacy
support is disabled (CONFIG_CIFS_ALLOW_INSECURE_LEGACY turned
off). For example smb2_operations and smb2_values aren't used
in that case. Over time we can move more and more SMB1/CIFS and SMB2.0
code into the insecure legacy ifdefs
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d5946274d ]
With large and many guest with storage keys it is possible to create
large latencies or stalls during initial key setting:
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: 18-....: (2099 ticks this GP) idle=54e/1/0x4000000000000002 softirq=35598716/35598716 fqs=998
(t=2100 jiffies g=155867385 q=20879)
Task dump for CPU 18:
CPU 1/KVM R running task 0 1030947 256019 0x06000004
Call Trace:
sched_show_task
rcu_dump_cpu_stacks
rcu_sched_clock_irq
update_process_times
tick_sched_handle
tick_sched_timer
__hrtimer_run_queues
hrtimer_interrupt
do_IRQ
ext_int_handler
ptep_zap_key
The mmap lock is held during the page walking but since this is a
semaphore scheduling is still possible. Same for the kvm srcu.
To minimize overhead do this on every segment table entry or large page.
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Link: https://lore.kernel.org/r/20220530092706.11637-2-borntraeger@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09dadb5985 ]
In our tests, "qemu-nbd" triggers a io hung:
INFO: task qemu-nbd:11445 blocked for more than 368 seconds.
Not tainted 5.18.0-rc3-next-20220422-00003-g2176915513ca #884
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:qemu-nbd state:D stack: 0 pid:11445 ppid: 1 flags:0x00000000
Call Trace:
<TASK>
__schedule+0x480/0x1050
? _raw_spin_lock_irqsave+0x3e/0xb0
schedule+0x9c/0x1b0
blk_mq_freeze_queue_wait+0x9d/0xf0
? ipi_rseq+0x70/0x70
blk_mq_freeze_queue+0x2b/0x40
nbd_add_socket+0x6b/0x270 [nbd]
nbd_ioctl+0x383/0x510 [nbd]
blkdev_ioctl+0x18e/0x3e0
__x64_sys_ioctl+0xac/0x120
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7fd8ff706577
RSP: 002b:00007fd8fcdfebf8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 0000000040000000 RCX: 00007fd8ff706577
RDX: 000000000000000d RSI: 000000000000ab00 RDI: 000000000000000f
RBP: 000000000000000f R08: 000000000000fbe8 R09: 000055fe497c62b0
R10: 00000002aff20000 R11: 0000000000000246 R12: 000000000000006d
R13: 0000000000000000 R14: 00007ffe82dc5e70 R15: 00007fd8fcdff9c0
"qemu-ndb -d" will call ioctl 'NBD_DISCONNECT' first, however, following
message was found:
block nbd0: Send disconnect failed -32
Which indicate that something is wrong with the server. Then,
"qemu-nbd -d" will call ioctl 'NBD_CLEAR_SOCK', however ioctl can't clear
requests after commit 2516ab1543fd("nbd: only clear the queue on device
teardown"). And in the meantime, request can't complete through timeout
because nbd_xmit_timeout() will always return 'BLK_EH_RESET_TIMER', which
means such request will never be completed in this situation.
Now that the flag 'NBD_CMD_INFLIGHT' can make sure requests won't
complete multiple times, switch back to call nbd_clear_sock() in
nbd_clear_sock_ioctl(), so that inflight requests can be cleared.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20220521073749.3146892-5-yukuai3@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c55b2b983b ]
When nbd module is being removing, nbd_alloc_config() may be
called concurrently by nbd_genl_connect(), although try_module_get()
will return false, but nbd_alloc_config() doesn't handle it.
The race may lead to the leak of nbd_config and its related
resources (e.g, recv_workq) and oops in nbd_read_stat() due
to the unload of nbd module as shown below:
BUG: kernel NULL pointer dereference, address: 0000000000000040
Oops: 0000 [#1] SMP PTI
CPU: 5 PID: 13840 Comm: kworker/u17:33 Not tainted 5.14.0+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
Workqueue: knbd16-recv recv_work [nbd]
RIP: 0010:nbd_read_stat.cold+0x130/0x1a4 [nbd]
Call Trace:
recv_work+0x3b/0xb0 [nbd]
process_one_work+0x1ed/0x390
worker_thread+0x4a/0x3d0
kthread+0x12a/0x150
ret_from_fork+0x22/0x30
Fixing it by checking the return value of try_module_get()
in nbd_alloc_config(). As nbd_alloc_config() may return ERR_PTR(-ENODEV),
assign nbd->config only when nbd_alloc_config() succeeds to ensure
the value of nbd->config is binary (valid or NULL).
Also adding a debug message to check the reference counter
of nbd_config during module removal.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20220521073749.3146892-3-yukuai3@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 656d054e0a ]
When building x86_64 with JUMP_LABEL=n it's possible for
instrumentation to sneak into noinstr:
vmlinux.o: warning: objtool: exit_to_user_mode+0x14: call to static_key_count.constprop.0() leaves .noinstr.text section
vmlinux.o: warning: objtool: syscall_exit_to_user_mode+0x2d: call to static_key_count.constprop.0() leaves .noinstr.text section
vmlinux.o: warning: objtool: irqentry_exit_to_user_mode+0x1b: call to static_key_count.constprop.0() leaves .noinstr.text section
Switch to arch_ prefixed atomic to avoid the explicit instrumentation.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a6a5eb269f ]
As x86 uses the <asm-generic/bitops/instrumented-*.h> headers, the
regular forms of all bitops are instrumented with explicit calls to
KASAN and KCSAN checks. As these are explicit calls, these are not
suppressed by the noinstr function attribute.
This can result in calls to those check functions in noinstr code, which
objtool warns about:
vmlinux.o: warning: objtool: enter_from_user_mode+0x24: call to __kcsan_check_access() leaves .noinstr.text section
vmlinux.o: warning: objtool: syscall_enter_from_user_mode+0x28: call to __kcsan_check_access() leaves .noinstr.text section
vmlinux.o: warning: objtool: syscall_enter_from_user_mode_prepare+0x24: call to __kcsan_check_access() leaves .noinstr.text section
vmlinux.o: warning: objtool: irqentry_enter_from_user_mode+0x24: call to __kcsan_check_access() leaves .noinstr.text section
Prevent this by using the arch_*() bitops, which are the underlying
bitops without explciit instrumentation.
[null: Changelog]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220502111216.290518605@infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6b732666a ]
The return value of is_arm_mapping_symbol() is unpredictable when "$"
is passed in.
strchr(3) says:
The strchr() and strrchr() functions return a pointer to the matched
character or NULL if the character is not found. The terminating null
byte is considered part of the string, so that if c is specified as
'\0', these functions return a pointer to the terminator.
When str[1] is '\0', strchr("axtd", str[1]) is not NULL, and str[2] is
referenced (i.e. buffer overrun).
Test code
---------
char str1[] = "abc";
char str2[] = "ab";
strcpy(str1, "$");
strcpy(str2, "$");
printf("test1: %d\n", is_arm_mapping_symbol(str1));
printf("test2: %d\n", is_arm_mapping_symbol(str2));
Result
------
test1: 0
test2: 1
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5a9597d69 ]
Today, all possible serial lines (ssl*=) as well as all
possible consoles (con*=) each share a single interrupt
(with a fixed number) with others of the same type.
Now, if you have two lines, say ssl0 and ssl1, and one
of them is connected to an fd you cannot read (e.g. a
file), but the other gets a read interrupt, then both
of them get the interrupt since it's shared. Then, the
read() call will return EOF, since it's a file being
written and there's nothing to read (at least not at
the current offset, at the end).
Unfortunately, this is treated as a read error, and we
close this line, losing all the possible output.
It might be possible to work around this and make the
IRQ sharing work, however, now that we have dynamically
allocated IRQs that are easy to use, simply use that to
achieve separating between the events; then there's no
interrupt for that line and we never attempt the read
in the first place, thus not closing the line.
This manifested itself in the wifi hostap/hwsim tests
where the parallel script communicates via one serial
console and the kernel messages go to another (a file)
and sending data on the communication console caused
the kernel messages to stop flowing into the file.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-By: anton ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0f4d663fc ]
On aldebaran, when thermal throttling happens due to excessive GPU
temperature, the reason for throttling event is missed in warning
message. This patch fixes it.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2b28708b6 ]
In radeon_fp_native_mode(), the return value of drm_mode_duplicate()
is assigned to mode, which will lead to a NULL pointer dereference
on failure of drm_mode_duplicate(). Add a check to avoid npd.
The failure status of drm_cvt_mode() on the other path is checked too.
Signed-off-by: Gong Yuanjun <ruc_gongyuanjun@163.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 49947b906a ]
[How & Why]
If a value of 0 is read, then this will cause a divide-by-0 panic.
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b2ba3c561 ]
Before waiting for a request's safe reply, we will send the mdlog flush
request to the relevant MDS. And this will also flush the mdlog for all
the other unsafe requests in the same session, so we can record the last
session and no need to flush mdlog again in the next loop. But there
still have cases that it may send the mdlog flush requst twice or more,
but that should be not often.
Rename wait_unsafe_requests() to
flush_mdlog_and_wait_mdsc_unsafe_requests() to make it more
descriptive.
[xiubli: fold in MDS request refcount leak fix from Jeff]
URL: https://tracker.ceph.com/issues/55284
URL: https://tracker.ceph.com/issues/55411
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7a2dc5230 ]
`rctime' has been a pain point in cephfs due to its buggy
nature - inconsistent values reported and those sorts.
Fixing rctime is non-trivial needing an overall redesign
of the entire nested statistics infrastructure.
As a workaround, PR
http://github.com/ceph/ceph/pull/37938
allows this extended attribute to be manually set. This allows
users to "fixup" inconsistent rctime values. While this sounds
messy, its probably the wisest approach allowing users/scripts
to workaround buggy rctime values.
The above PR enables Ceph MDS to allow manually setting
rctime extended attribute with the corresponding user-land
changes. We may as well allow the same to be done via kclient
for parity.
Signed-off-by: Venky Shankar <vshankar@redhat.com>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c90c9b3e5 ]
This reverts commit 4dc2a5a8f6.
A non-zero return value from pfkey_broadcast() does not necessarily mean
an error occurred as this function returns -ESRCH when no registered
listener received the message. In particular, a call with
BROADCAST_PROMISC_ONLY flag and null one_sk argument can never return
zero so that this commit in fact prevents processing any PF_KEY message.
One visible effect is that racoon daemon fails to find encryption
algorithms like aes and refuses to start.
Excluding -ESRCH return value would fix this but it's not obvious that
we really want to bail out here and most other callers of
pfkey_broadcast() also ignore the return value. Also, as pointed out by
Steffen Klassert, PF_KEY is kind of deprecated and newer userspace code
should use netlink instead so that we should only disturb the code for
really important fixes.
v2: add a comment explaining why is the return value ignored
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9f0a46141 ]
When myrb_probe() fails the callback might not be set, so we need to
validate the 'disable_intr' callback in myrb_cleanup() to not cause a null
pointer exception. And while at it do not call myrb_cleanup() if we cannot
enable the PCI device at all.
Link: https://lore.kernel.org/r/20220523120244.99515-1-hare@suse.de
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Tested-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e26774228 ]
Generally, the md_unregister_thread is called with reconfig_mutex, but
raid_message in dm-raid doesn't hold reconfig_mutex to unregister thread,
so md_unregister_thread can be called simulitaneously from two call sites
in theory.
Then after previous commit which remove the protection of reconfig_mutex
for md_unregister_thread completely, the potential issue could be worse
than before.
Let's take pers_lock at the beginning of function to ensure reentrancy.
Reported-by: Donald Buczek <buczek@molgen.mpg.de>
Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27fdf84510 ]
Executing reboot command several times on the machine "Dell
PowerEdge R740", UEFI security detection stopped machine
with the following prompt:
UEFI0082: The system was reset due to a timeout from the watchdog
timer. Check the System Event Log (SEL) or crash dumps from
Operating Sysstem to identify the source that triggered the
watchdog timer reset. Update the firmware or driver for the
identified device.
iDRAC has warning event: "The watchdog timer reset the system".
This patch fixes this issue by adding the reboot notifier.
Signed-off-by: Liu Xinpeng <liuxp11@chinatelecom.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1650984810-6247-3-git-send-email-liuxp11@chinatelecom.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a702dc88e ]
Previously the protection of kernfs_pr_cont_buf was piggy backed by
rename_lock, which means that pr_cont() needs to be protected under
rename_lock. This can cause potential circular lock dependencies.
If there is an OOM, we have the following call hierarchy:
-> cpuset_print_current_mems_allowed()
-> pr_cont_cgroup_name()
-> pr_cont_kernfs_name()
pr_cont_kernfs_name() will grab rename_lock and call printk. So we have
the following lock dependencies:
kernfs_rename_lock -> console_sem
Sometimes, printk does a wakeup before releasing console_sem, which has
the dependence chain:
console_sem -> p->pi_lock -> rq->lock
Now, imagine one wants to read cgroup_name under rq->lock, for example,
printing cgroup_name in a tracepoint in the scheduler code. They will
be holding rq->lock and take rename_lock:
rq->lock -> kernfs_rename_lock
Now they will deadlock.
A prevention to this circular lock dependency is to separate the
protection of pr_cont_buf from rename_lock. In principle, rename_lock
is to protect the integrity of cgroup name when copying to buf. Once
pr_cont_buf has got its content, rename_lock can be dropped. So it's
safe to drop rename_lock after kernfs_name_locked (and
kernfs_path_from_node_locked) and rely on a dedicated pr_cont_lock
to protect pr_cont_buf.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hao Luo <haoluo@google.com>
Link: https://lore.kernel.org/r/20220516190951.3144144-1-haoluo@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aabdbb1b7a ]
__msm_console_write() assumes that interrupts are disabled, but
with threaded console printers it is possible that the write()
callback of the console is called with interrupts enabled.
Explicitly disable interrupts using local_irq_save() to preserve
the assumed context.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20220506213324.470461-1-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a98399cbc1 ]
When a machine sports more than one SP804 timer instance, we only bring
up the first one, since multiple timers of the same kind are not useful
to Linux. As this is intentional behaviour, we should not return an
error message, as we do today:
===============
[ 0.000800] Failed to initialize '/bus@8000000/motherboard-bus@8000000/iofpga-bus@300000000/timer@120000': -22
===============
Replace the -EINVAL return with a debug message and return 0 instead.
Also we do not reach the init function anymore if the DT node is
disabled (as this is now handled by OF_DECLARE), so remove the explicit
check for that case.
This fixes a long standing bogus error when booting ARM's fastmodels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20220506162522.3675399-1-andre.przywara@arm.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dcc2afe71 ]
Currently, someone can invoke the sysfs such as state_show()
intermittently before dev_set_drvdata() is done.
And it can be a cause of kernel Oops because of edev is Null at that time.
So modified the driver registration to after setting drviver data.
- Oops's backtrace.
Backtrace:
[<c067865c>] (state_show) from [<c05222e8>] (dev_attr_show)
[<c05222c0>] (dev_attr_show) from [<c02c66e0>] (sysfs_kf_seq_show)
[<c02c6648>] (sysfs_kf_seq_show) from [<c02c496c>] (kernfs_seq_show)
[<c02c4938>] (kernfs_seq_show) from [<c025e2a0>] (seq_read)
[<c025e11c>] (seq_read) from [<c02c50a0>] (kernfs_fop_read)
[<c02c5064>] (kernfs_fop_read) from [<c0231cac>] (__vfs_read)
[<c0231c5c>] (__vfs_read) from [<c0231ee0>] (vfs_read)
[<c0231e34>] (vfs_read) from [<c0232464>] (ksys_read)
[<c02323f0>] (ksys_read) from [<c02324fc>] (sys_read)
[<c02324e4>] (sys_read) from [<c00091d0>] (__sys_trace_return)
Signed-off-by: bumwoo lee <bw365.lee@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58e4a2d27d ]
The extcon_get_extcon_dev() function returns error pointers on error,
NULL when it's a -EPROBE_DEFER defer situation, and ERR_PTR(-ENODEV)
when the CONFIG_EXTCON option is disabled. This is very complicated for
the callers to handle and a number of them had bugs that would lead to
an Oops.
In real life, there are two things which prevented crashes. First,
error pointers would only be returned if there was bug in the caller
where they passed a NULL "extcon_name" and none of them do that.
Second, only two out of the eight drivers will build when CONFIG_EXTCON
is disabled.
The normal way to write this would be to return -EPROBE_DEFER directly
when appropriate and return NULL when CONFIG_EXTCON is disabled. Then
the error handling is simple and just looks like:
dev->edev = extcon_get_extcon_dev(acpi_dev_name(adev));
if (IS_ERR(dev->edev))
return PTR_ERR(dev->edev);
For the two drivers which can build with CONFIG_EXTCON disabled, then
extcon_get_extcon_dev() will now return NULL which is not treated as an
error and the probe will continue successfully. Those two drivers are
"typec_fusb302" and "max8997-battery". In the original code, the
typec_fusb302 driver had an 800ms hang in tcpm_get_current_limit() but
now that function is a no-op. For the max8997-battery driver everything
should continue working as is.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f861d36e02 ]
rtsx_usb_probe() doesn't call usb_set_intfdata() to null out the
interface pointer when probe fails. This leaves a stale pointer.
Noticed the missing usb_set_intfdata() while debugging an unrelated
invalid DMA mapping problem.
Fix it with a call to usb_set_intfdata(..., NULL).
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220429210913.46804-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74da272400 ]
Currently timeout for autoenumeration during probe and bus reset is set to
2 secs which is really a big value. This can have an adverse effect on
boot time if the slave device is not ready/reset.
This was the case with wcd938x which was not reset yet but we spent 2
secs waiting in the soundwire controller probe. Reduce this time to
1/10 of Hz which should be good enough time to finish autoenumeration
if any slaves are available on the bus.
Reported-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220506084705.18525-1-srinivas.kandagatla@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3120aac6d0 ]
UDC driver should not touch gadget's driver internals, especially it
should not reset driver->bus. This wasn't harmful so far, but since
commit fc274c1e99 ("USB: gadget: Add a new bus for gadgets") gadget
subsystem got it's own bus and messing with ->bus triggers the
following NULL pointer dereference:
dwc2 12480000.hsotg: bound driver g_ether
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in: ...
CPU: 0 PID: 620 Comm: modprobe Not tainted 5.18.0-rc5-next-20220504 #11862
Hardware name: Samsung Exynos (Flattened Device Tree)
PC is at module_add_driver+0x44/0xe8
LR is at sysfs_do_create_link_sd+0x84/0xe0
...
Process modprobe (pid: 620, stack limit = 0x(ptrval))
...
module_add_driver from bus_add_driver+0xf4/0x1e4
bus_add_driver from driver_register+0x78/0x10c
driver_register from usb_gadget_register_driver_owner+0x40/0xb4
usb_gadget_register_driver_owner from do_one_initcall+0x44/0x1e0
do_one_initcall from do_init_module+0x44/0x1c8
do_init_module from load_module+0x19b8/0x1b9c
load_module from sys_finit_module+0xdc/0xfc
sys_finit_module from ret_fast_syscall+0x0/0x54
Exception stack(0xf1771fa8 to 0xf1771ff0)
...
dwc2 12480000.hsotg: new device is high-speed
---[ end trace 0000000000000000 ]---
Fix this by removing driver->bus entry reset.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220505104618.22729-1-m.szyprowski@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b67d19662f ]
usb_get_dev is called in xillyusb_probe. So it is better to call
usb_put_dev before xdev is released.
Acked-by: Eli Billauer <eli.billauer@gmail.com>
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Link: https://lore.kernel.org/r/20220406075703.23464-1-hbh25y@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63acaa8e9c ]
The documentation for the freeze() method says that it "should quiesce
the device so that it doesn't generate IRQs or DMA". The unspoken
consequence of not doing this is that MSIs aimed at non-boot CPUs may
get fully lost if they're sent during the period where the target CPU is
offline.
The current callbacks for USB HCD do not fully quiesce interrupts,
specifically on XHCI. Change to use the full suspend/resume flow for
freeze/thaw to ensure interrupts are fully quiesced. This fixes issues
where USB devices fail to thaw during hibernation because XHCI misses
its interrupt and cannot recover.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20220421103751.v3.2.I8226c7fdae88329ef70957b96a39b346c69a914e@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d378f2ae5 ]
There is a deadlock in oxu_bus_suspend(), which is shown below:
(Thread 1) | (Thread 2)
| timer_action()
oxu_bus_suspend() | mod_timer()
spin_lock_irq() //(1) | (wait a time)
... | oxu_watchdog()
del_timer_sync() | spin_lock_irq() //(2)
(wait timer to stop) | ...
We hold oxu->lock in position (1) of thread 1, and use
del_timer_sync() to wait timer to stop, but timer handler
also need oxu->lock in position (2) of thread 2. As a result,
oxu_bus_suspend() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irq(), which could let timer handler to obtain
the needed lock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417120305.64577-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62b2caef40 ]
There is a deadlock in sa1100_set_termios(), which is shown
below:
(Thread 1) | (Thread 2)
| sa1100_enable_ms()
sa1100_set_termios() | mod_timer()
spin_lock_irqsave() //(1) | (wait a time)
... | sa1100_timeout()
del_timer_sync() | spin_lock_irqsave() //(2)
(wait timer to stop) | ...
We hold sport->port.lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need sport->port.lock in position (2) of thread 2. As a result,
sa1100_set_termios() will block forever.
This patch moves del_timer_sync() before spin_lock_irqsave()
in order to prevent the deadlock.
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220417111626.7802-1-duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 134a3408c2 ]
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Zhen Ni <nizhen@uniontech.com>
Link: https://lore.kernel.org/r/20220302033716.31272-1-nizhen@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ilya Maximets
Tan Tee Min
Adrian Hunter
Sergey Shtylyov
David Safford
Paulo Alcantara
Shyam Prasad N
Jeremy Soller
Cameron Berkenpas
huangwenhui
Takashi Iwai
Kuan-Ying Lee
Xie Yongji
Kees Cook
Yury Norov
Steve French
Christian Borntraeger
Yu Kuai
Peter Zijlstra
Masahiro Yamada
Johannes Berg
Lijo Lazar
Gong Yuanjun
David Galiffi
Xiubo Li
Venky Shankar
Michal Kubecek
Hannes Reinecke
Guoqing Jiang
Liu Xinpeng
Hao Luo
John Ogness
Wang Cheng
Andre Przywara
bumwoo lee
Dan Carpenter
Shuah Khan
Srinivas Kandagatla
Marek Szyprowski
Changbin Du
Hangyu Hua
Evan Green
Duoming Zhou
Zhen Ni