Cleanup net/sched code to current CodingStyle and practices.
Reduce inline abuse
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alban Crequy <alban.crequy@collabora.co.uk>
Reviewed-by: Ian Molton <ian.molton@collabora.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements a mqprio queueing discipline that by default creates
a pfifo_fast qdisc per tx queue and provides the needed configuration
interface.
Using the mqprio qdisc the number of tcs currently in use along
with the range of queues alloted to each class can be configured. By
default skbs are mapped to traffic classes using the skb priority.
This mapping is configurable.
Configurable parameters,
struct tc_mqprio_qopt {
__u8 num_tc;
__u8 prio_tc_map[TC_BITMASK + 1];
__u8 hw;
__u16 count[TC_MAX_QUEUE];
__u16 offset[TC_MAX_QUEUE];
};
Here the count/offset pairing give the queue alignment and the
prio_tc_map gives the mapping from skb->priority to tc.
The hw bit determines if the hardware should configure the count
and offset values. If the hardware bit is set then the operation
will fail if the hardware does not implement the ndo_setup_tc
operation. This is to avoid undetermined states where the hardware
may or may not control the queue mapping. Also minimal bounds
checking is done on the count/offset to verify a queue does not
exceed num_tx_queues and that queue ranges do not overlap. Otherwise
it is left to user policy or hardware configuration to create
useful mappings.
It is expected that hardware QOS schemes can be implemented by
creating appropriate mappings of queues in ndo_tc_setup().
One expected use case is drivers will use the ndo_setup_tc to map
queue ranges onto 802.1Q traffic classes. This provides a generic
mechanism to map network traffic onto these traffic classes and
removes the need for lower layer drivers to know specifics about
traffic types.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides a mechanism for lower layer devices to
steer traffic using skb->priority to tx queues. This allows
for hardware based QOS schemes to use the default qdisc without
incurring the penalties related to global state and the qdisc
lock. While reliably receiving skbs on the correct tx ring
to avoid head of line blocking resulting from shuffling in
the LLD. Finally, all the goodness from txq caching and xps/rps
can still be leveraged.
Many drivers and hardware exist with the ability to implement
QOS schemes in the hardware but currently these drivers tend
to rely on firmware to reroute specific traffic, a driver
specific select_queue or the queue_mapping action in the
qdisc.
By using select_queue for this drivers need to be updated for
each and every traffic type and we lose the goodness of much
of the upstream work. Firmware solutions are inherently
inflexible. And finally if admins are expected to build a
qdisc and filter rules to steer traffic this requires knowledge
of how the hardware is currently configured. The number of tx
queues and the queue offsets may change depending on resources.
Also this approach incurs all the overhead of a qdisc with filters.
With the mechanism in this patch users can set skb priority using
expected methods ie setsockopt() or the stack can set the priority
directly. Then the skb will be steered to the correct tx queues
aligned with hardware QOS traffic classes. In the normal case with
single traffic class and all queues in this class everything
works as is until the LLD enables multiple tcs.
To steer the skb we mask out the lower 4 bits of the priority
and allow the hardware to configure upto 15 distinct classes
of traffic. This is expected to be sufficient for most applications
at any rate it is more then the 8021Q spec designates and is
equal to the number of prio bands currently implemented in
the default qdisc.
This in conjunction with a userspace application such as
lldpad can be used to implement 8021Q transmission selection
algorithms one of these algorithms being the extended transmission
selection algorithm currently being used for DCB.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a rtnetlink request specifies a negative or zero ifindex and has no
interface name attribute, but has a group attribute, then the chenges
are made to all the interfaces belonging to the specified group.
Signed-off-by: Vlad Dogaru <ddvlad@rosedu.org>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Net devices can now be grouped, enabling simpler manipulation from
userspace. This patch adds a group field to the net_device structure, as
well as rtnetlink support to query and modify it.
Signed-off-by: Vlad Dogaru <ddvlad@rosedu.org>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up some unused macros in net/*.
1. be left for code change. e.g. PGV_FROM_VMALLOC, PGV_FROM_VMALLOC, KMEM_SAFETYZONE.
2. never be used since introduced to kernel.
e.g. P9_RDMA_MAX_SGE, UTIL_CTRL_PKT_SIZE.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Acked-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet filter (BPF) doesnt need to disable softirqs, being fully
re-entrant and lock-less.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux Socket Filters can already be successfully attached and detached on unix
sockets with setsockopt(sockfd, SOL_SOCKET, SO_{ATTACH,DETACH}_FILTER, ...).
See: Documentation/networking/filter.txt
But the filter was never used in the unix socket code so it did not work. This
patch uses sk_filter() to filter buffers before delivery.
This short program demonstrates the problem on SOCK_DGRAM.
int main(void) {
int i, j, ret;
int sv[2];
struct pollfd fds[2];
char *message = "Hello world!";
char buffer[64];
struct sock_filter ins[32] = {{0,},};
struct sock_fprog filter;
socketpair(AF_UNIX, SOCK_DGRAM, 0, sv);
for (i = 0 ; i < 2 ; i++) {
fds[i].fd = sv[i];
fds[i].events = POLLIN;
fds[i].revents = 0;
}
for(j = 1 ; j < 13 ; j++) {
/* Set a socket filter to truncate the message */
memset(ins, 0, sizeof(ins));
ins[0].code = BPF_RET|BPF_K;
ins[0].k = j;
filter.len = 1;
filter.filter = ins;
setsockopt(sv[1], SOL_SOCKET, SO_ATTACH_FILTER, &filter, sizeof(filter));
/* send a message */
send(sv[0], message, strlen(message) + 1, 0);
/* The filter should let the message pass but truncated. */
poll(fds, 2, 0);
/* Receive the truncated message*/
ret = recv(sv[1], buffer, 64, 0);
printf("received %d bytes, expected %d\n", ret, j);
}
for (i = 0 ; i < 2 ; i++)
close(sv[i]);
return 0;
}
Signed-off-by: Alban Crequy <alban.crequy@collabora.co.uk>
Reviewed-by: Ian Molton <ian.molton@collabora.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netif_skb_features() we return only the features that are valid for vlans
if we have a vlan packet. However, we should not mask out NETIF_F_HW_VLAN_TX
since it enables transmission of vlan tags and is obviously valid.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a network namespace is created (via CLONE_NEWNET), the loopback
interface is automatically added to the new namespace, triggering a
printk in ipv6_add_dev() if CONFIG_IPV6_PRIVACY is set.
This is problematic for applications which use CLONE_NEWNET as
part of a sandbox, like Chromium's suid sandbox or recent versions of
vsftpd. On a busy machine, it can lead to thousands of useless
"lo: Disabled Privacy Extensions" messages appearing in dmesg.
It's easy enough to check the status of privacy extensions via the
use_tempaddr sysctl, so just removing the printk seems like the most
sensible solution.
Signed-off-by: Romain Francoise <romain@orebokech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original code we check if (servl == NULL) twice. The first time
should print the message that cfmuxl_remove_uplayer() failed and set
"ret" correctly, but instead it just returns success. The second check
should be checking the value of "ret" instead of "servl".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the CAN socket code conform to the manpage of sendmsg.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux 2.6.21 defines different macros for __attribute__ which are also
used inside batman-adv. The next version of checkpatch.pl warns about
the usage of __attribute__((packed))).
Linux 2.6.33 defines an extra macro __always_unused which is used to
assist source code analyzers and can be used to removed the last
existing __attribute__ inside the source code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
GRETH: resolve SMP issues and other problems
GRETH: handle frame error interrupts
GRETH: avoid writing bad speed/duplex when setting transfer mode
GRETH: fixed skb buffer memory leak on frame errors
GRETH: GBit transmit descriptor handling optimization
GRETH: fix opening/closing
GRETH: added raw AMBA vendor/device number to match against.
cassini: Fix build bustage on x86.
e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs
e1000e: update Copyright for 2011
e1000: Avoid unhandled IRQ
r8169: keep firmware in memory.
netdev: tilepro: Use is_unicast_ether_addr helper
etherdevice.h: Add is_unicast_ether_addr function
ks8695net: Use default implementation of ethtool_ops::get_link
ks8695net: Disable non-working ethtool operations
USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable.
vxge: Remember to release firmware after upgrading firmware
netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr
ipsec: update MAX_AH_AUTH_LEN to support sha512
...
* 'for-2.6.38' of git://linux-nfs.org/~bfields/linux: (62 commits)
nfsd4: fix callback restarting
nfsd: break lease on unlink, link, and rename
nfsd4: break lease on nfsd setattr
nfsd: don't support msnfs export option
nfsd4: initialize cb_per_client
nfsd4: allow restarting callbacks
nfsd4: simplify nfsd4_cb_prepare
nfsd4: give out delegations more quickly in 4.1 case
nfsd4: add helper function to run callbacks
nfsd4: make sure sequence flags are set after destroy_session
nfsd4: re-probe callback on connection loss
nfsd4: set sequence flag when backchannel is down
nfsd4: keep finer-grained callback status
rpc: allow xprt_class->setup to return a preexisting xprt
rpc: keep backchannel xprt as long as server connection
rpc: move sk_bc_xprt to svc_xprt
nfsd4: allow backchannel recovery
nfsd4: support BIND_CONN_TO_SESSION
nfsd4: modify session list under cl_lock
Documentation: fl_mylease no longer exists
...
Fix up conflicts in fs/nfsd/vfs.c with the vfs-scale work. The
vfs-scale work touched some msnfs cases, and this merge removes support
for that entirely, so the conflict was trivial to resolve.
After recent changes, (percpu stats on vlan/tunnels...), we dont need
anymore per struct netdev_queue tx_bytes/tx_packets/tx_dropped counters.
Only remaining users are ixgbe, sch_teql, gianfar & macvlan :
1) ixgbe can be converted to use existing tx_ring counters.
2) macvlan incremented txq->tx_dropped, it can use the
dev->stats.tx_dropped counter.
3) sch_teql : almost revert ab35cd4b8f (Use net_device internal stats)
Now we have ndo_get_stats64(), use it, even for "unsigned long"
fields (No need to bring back a struct net_device_stats)
4) gianfar adds a stats structure per tx queue to hold
tx_bytes/tx_packets
This removes a lockdep warning (and possible lockup) in rndis gadget,
calling dev_get_stats() from hard IRQ context.
Ref: http://www.spinics.net/lists/netdev/msg149202.html
Reported-by: Neil Jones <neiljay@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a problem in net/batman-adv/unicast.c::frag_send_skb().
dev_alloc_skb() allocates memory and may fail, thus returning NULL. If
this happens we'll pass a NULL pointer on to skb_split() which in turn
hands it to skb_split_inside_header() from where it gets passed to
skb_put() that lets skb_tail_pointer() play with it and that function
dereferences it. And thus the bat dies.
While I was at it I also moved the call to dev_alloc_skb() above the
assignment to 'unicast_packet' since there's no reason to do that
assignment if the memory allocation fails.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When the buffer size is set to zero in the block ack parameter set
field, we should use the maximum supported number of subframes. The
existing code was bogus and was doing some unnecessary calculations
that lead to wrong values.
Thanks Johannes for helping me figure this one out.
Cc: stable@kernel.org
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the introduction of the fixes for the
reorder timer, mac80211 will cause lockdep
warnings because lockdep confuses
local->skb_queue and local->rx_skb_queue
and treats their lock as the same.
However, their locks are different, and are
valid in different contexts (the former is
used in IRQ context, the latter in BH only)
and the only thing to be done is mark the
former as a different lock class so that
lockdep can tell the difference.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Sujith <m.sujith@gmail.com>
Reported-by: Miles Lane <miles.lane@gmail.com>
Tested-by: Sujith <m.sujith@gmail.com>
Tested-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (41 commits)
fs: add documentation on fallocate hole punching
Gfs2: fail if we try to use hole punch
Btrfs: fail if we try to use hole punch
Ext4: fail if we try to use hole punch
Ocfs2: handle hole punching via fallocate properly
XFS: handle hole punching via fallocate properly
fs: add hole punching to fallocate
vfs: pass struct file to do_truncate on O_TRUNC opens (try #2)
fix signedness mess in rw_verify_area() on 64bit architectures
fs: fix kernel-doc for dcache::prepend_path
fs: fix kernel-doc for dcache::d_validate
sanitize ecryptfs ->mount()
switch afs
move internal-only parts of ncpfs headers to fs/ncpfs
switch ncpfs
switch 9p
pass default dentry_operations to mount_pseudo()
switch hostfs
switch affs
switch configfs
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: fix cleanup when trying to mount inexistent image
net/ceph: make ceph_msgr_wq non-reentrant
ceph: fsc->*_wq's aren't used in memory reclaim path
ceph: Always free allocated memory in osdmap_decode()
ceph: Makefile: Remove unnessary code
ceph: associate requests with opening sessions
ceph: drop redundant r_mds field
ceph: implement DIRLAYOUTHASH feature to get dir layout from MDS
ceph: add dir_layout to inode
This patch fixes a loop in ctnetlink_get_conntrack() that can be
triggered if you use the same socket to receive events and to
perform a GET operation. Under heavy load, netlink_unicast()
may return -EAGAIN, this error code is reserved in nfnetlink for
the module load-on-demand. Instead, we return -ENOBUFS which is
the appropriate error code that has to be propagated to
user-space.
Reported-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fix new kernel-doc warning (copy-paste typo):
Warning(net/ethernet/eth.c:366): No description found for parameter 'rxqs'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux IPv6 forwards unicast packets, which are link layer multicasts...
The hole was present since day one. I was 100% this check is there, but it is not.
The problem shows itself, f.e. when Microsoft Network Load Balancer runs on a network.
This software resolves IPv6 unicast addresses to multicast MAC addresses.
Signed-off-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
ceph messenger code does a rather complex dancing around multithread
workqueue to make sure the same work item isn't executed concurrently
on different CPUs. This restriction can be provided by workqueue with
WQ_NON_REENTRANT.
Make ceph_msgr_wq non-reentrant workqueue with the default concurrency
level and remove the QUEUED/BUSY logic.
* This removes backoff handling in con_work() but it couldn't reliably
block execution of con_work() to begin with - queue_con() can be
called after the work started but before BUSY is set. It seems that
it was an optimization for a rather cold path and can be safely
removed.
* The number of concurrent work items is bound by the number of
connections and connetions are independent from each other. With
the default concurrency level, different connections will be
executed independently.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Sage Weil <sage@newdream.net>
Cc: ceph-devel@vger.kernel.org
Signed-off-by: Sage Weil <sage@newdream.net>
Add a ceph_dir_layout to the inode, and calculate dentry hash values based
on the parent directory's specified dir_hash function. This is needed
because the old default Linux dcache hash function is extremely week and
leads to a poor distribution of files among dir fragments.
Signed-off-by: Sage Weil <sage@newdream.net>
The IPv6 tproxy patches split IPv6 defragmentation off of conntrack, but
failed to update the #ifdef stanzas guarding the defragmentation related
fields and code in skbuff and conntrack related code in nf_defrag_ipv6.c.
This patch adds the required #ifdefs so that IPv6 tproxy can truly be used
without connection tracking.
Original report:
http://marc.info/?l=linux-netdev&m=129010118516341&w=2
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: KOVACS Krisztian <hidden@balabit.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit fe10ae5338 adds a memset() to clear
the structure being sent back to userspace, but accidentally used the
wrong size.
Reported-by: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (67 commits)
cxgb4vf: recover from failure in cxgb4vf_open()
netfilter: ebtables: make broute table work again
netfilter: fix race in conntrack between dump_table and destroy
ah: reload pointers to skb data after calling skb_cow_data()
ah: update maximum truncated ICV length
xfrm: check trunc_len in XFRMA_ALG_AUTH_TRUNC
ehea: Increase the skb array usage
net/fec: remove config FEC2 as it's used nowhere
pcnet_cs: add new_id
tcp: disallow bind() to reuse addr/port
net/r8169: Update the function of parsing firmware
net: ppp: use {get,put}_unaligned_be{16,32}
CAIF: Fix IPv6 support in receive path for GPRS/3G
arp: allow to invalidate specific ARP entries
net_sched: factorize qdisc stats handling
mlx4: Call alloc_etherdev to allocate RX and TX queues
net: Add alloc_netdev_mqs function
caif: don't set connection request param size before copying data
cxgb4vf: fix mailbox data/control coherency domain race
qlcnic: change module parameter permissions
...
* 'nfs-for-2.6.38' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (89 commits)
NFS fix the setting of exchange id flag
NFS: Don't use vm_map_ram() in readdir
NFSv4: Ensure continued open and lockowner name uniqueness
NFS: Move cl_delegations to the nfs_server struct
NFS: Introduce nfs_detach_delegations()
NFS: Move cl_state_owners and related fields to the nfs_server struct
NFS: Allow walking nfs_client.cl_superblocks list outside client.c
pnfs: layout roc code
pnfs: update nfs4_callback_recallany to handle layouts
pnfs: add CB_LAYOUTRECALL handling
pnfs: CB_LAYOUTRECALL xdr code
pnfs: change lo refcounting to atomic_t
pnfs: check that partial LAYOUTGET return is ignored
pnfs: add layout to client list before sending rpc
pnfs: serialize LAYOUTGET(openstateid)
pnfs: layoutget rpc code cleanup
pnfs: change how lsegs are removed from layout list
pnfs: change layout state seqlock to a spinlock
pnfs: add prefix to struct pnfs_layout_hdr fields
pnfs: add prefix to struct pnfs_layout_segment fields
...
The netlink interface to dump the connection tracking table has a race
when entries are deleted at the same time. A customer reported a crash
and the backtrace showed thatctnetlink_dump_table was running while a
conntrack entry was being destroyed.
(see https://bugzilla.vyatta.com/show_bug.cgi?id=6402).
According to RCU documentation, when using hlist_nulls the reader
must handle the case of seeing a deleted entry and not proceed
further down the linked list. The old code would continue
which caused the scan to walk into the free list.
This patch uses locking (rather than RCU) for this operation which
is guaranteed safe, and no longer requires getting reference while
doing dump operation.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
skb_cow_data() may allocate a new data buffer, so pointers on
skb should be set after this function.
Bug was introduced by commit dff3bb06 ("ah4: convert to ahash")
and 8631e9bd ("ah6: convert to ahash").
Signed-off-by: Wang Xuefu <xuefu.wang@6wind.com>
Acked-by: Krzysztof Witek <krzysztof.witek@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maximum trunc length is defined by MAX_AH_AUTH_LEN (in bytes)
and need to be checked when this value is set (in bits) by
the user. In ah4.c and ah6.c a BUG_ON() checks this condiftion.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_csk_bind_conflict() logic currently disallows a bind() if
it finds a friend socket (a socket bound on same address/port)
satisfying a set of conditions :
1) Current (to be bound) socket doesnt have sk_reuse set
OR
2) other socket doesnt have sk_reuse set
OR
3) other socket is in LISTEN state
We should add the CLOSE state in the 3) condition, in order to avoid two
REUSEADDR sockets in CLOSE state with same local address/port, since
this can deny further operations.
Note : a prior patch tried to address the problem in a different (and
buggy) way. (commit fda48a0d7a tcp: bind() fix when many ports
are bound).
Reported-by: Gaspar Chilingarov <gasparch@gmail.com>
Reported-by: Daniel Baluta <daniel.baluta@gmail.com>
Tested-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to reuse the xprt associated with a server connection if
one has already been set up.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Multiple backchannels can share the same tcp connection; from rfc 5661 section
2.10.3.1:
A connection's association with a session is not exclusive. A
connection associated with the channel(s) of one session may be
simultaneously associated with the channel(s) of other sessions
including sessions associated with other client IDs.
However, multiple backchannels share a connection, they must all share
the same xid stream (hence the same rpc_xprt); the only way we have to
match replies with calls at the rpc layer is using the xid.
So, keep the rpc_xprt around as long as the connection lasts, in case
we're asked to use the connection as a backchannel again.
Requests to create new backchannel clients over a given server
connection should results in creating new clients that reuse the
existing rpc_xprt.
But to start, just reject attempts to associate multiple rpc_xprt's with
the same underlying bc_xprt.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This seems obviously transport-level information even if it's currently
used only by the server socket code.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Eric Dumazet
Alban Crequy
John Fastabend
Vlad Dogaru
Shan Wei
David S. Miller
Jesse Gross
Romain Francoise
Dan Carpenter
Kurt Van Dijck
Sven Eckelmann
Linus Torvalds
Tejun Heo
Jesper Juhl
Luciano Coelho
Johannes Berg
Pablo Neira Ayuso
Randy Dunlap
Alexey Kuznetsov
Al Viro
Sage Weil
KOVACS Krisztian
Kees Cook
Stephen Hemminger
Dang Hongwu
Nicolas Dichtel
J. Bruce Fields