Currently it doesn't matter where the mdio nodes are placed, but with
power management support (i.e. when sleep = <> properties will take
effect), mdio nodes placement will become important: mdio controller
is a part of the ethernet block, so the mdio nodes should be placed
correctly. Otherwise we may wrongly assume that MDIO controllers are
available during sleep.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (144 commits)
powerpc/44x: Support 16K/64K base page sizes on 44x
powerpc: Force memory size to be a multiple of PAGE_SIZE
powerpc/32: Wire up the trampoline code for kdump
powerpc/32: Add the ability for a classic ppc kernel to be loaded at 32M
powerpc/32: Allow __ioremap on RAM addresses for kdump kernel
powerpc/32: Setup OF properties for kdump
powerpc/32/kdump: Implement crash_setup_regs() using ppc_save_regs()
powerpc: Prepare xmon_save_regs for use with kdump
powerpc: Remove default kexec/crash_kernel ops assignments
powerpc: Make default kexec/crash_kernel ops implicit
powerpc: Setup OF properties for ppc32 kexec
powerpc/pseries: Fix cpu hotplug
powerpc: Fix KVM build on ppc440
powerpc/cell: add QPACE as a separate Cell platform
powerpc/cell: fix build breakage with CONFIG_SPUFS disabled
powerpc/mpc5200: fix error paths in PSC UART probe function
powerpc/mpc5200: add rts/cts handling in PSC UART driver
powerpc/mpc5200: Make PSC UART driver update serial errors counters
powerpc/mpc5200: Remove obsolete code from mpc5200 MDIO driver
powerpc/mpc5200: Add MDMA/UDMA support to MPC5200 ATA driver
...
Fix trivial conflict in drivers/char/Makefile as per Paul's directions
Does the same for the accompanying MDIO driver, and then modifies the TBI
configuration method. The old way used fields in einfo, which no longer
exists. The new way is to create an MDIO device-tree node for each instance
of gianfar, and create a tbi-handle property to associate ethernet controllers
with the TBI PHYs they are connected to.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just found the merge issue in 442746989d
("powerpc/83xx: Add support for MCU microcontroller in .dts files"):
the commit adds the MCU controller node into the DMA node, which is
wrong because the MCU sits on the I2C bus. Fix this by moving the MCU
node into the I2C controller node.
The original patch[1] was OK though. ;-)
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We don't want to encourage the device_type usage. It isn't used in
the code, so we can simply remove it from the dts files.
Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The RTC is sitting on the I2C2 bus at address 0x68. RTC interrupt signal
is connected to the IPIC's EXT2 interrupt line, the line is shared with
Vitesse 8201 Ethernet PHY.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MCU is an external Freescale MC9S08QG8 microcontroller, mainly used to
provide soft power-off function, but also exports two GPIOs (wired to
the LEDs and also available from the external headers).
Added the MCU on mpc8349emitx, mpc837xrdb and mpc8315erdb boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Modify mpc83xx_add_bridge to get config space register base address from
the device tree instead of immr + hardcoded offset.
83xx pci nodes have this change:
register properties now contain two address length tuples:
First is the pci bridge register base, this has always been there.
Second is the config base, this is new.
This is documented in dts-bindings/fsl/83xx-512x-pci.txt
The changes accomplish these things:
mpc83xx_add_bridge no longer needs to call get_immrbase
it uses hard coded addresses if the second register value is missing
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
add simple-bus compatible property to soc nodes for 83xx/85xx platforms
that were missing them. Add same to platform probe code.
This fixes SoC device drivers (such as talitos) to succeed in matching
devices present in the soc node.
also update mpc836x_rdk dts to new SEC bindings (overlooked in commit
3fd4473: powerpc/fsl: update crypto node definition and device tree
instances).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
delete obsolete device-type property, delete model property
(use compatible property instead), prepend "fsl," to Freescale
specific properties. Add nodes to device trees that are missing them,
and fix broken property values in other trees.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added DMA nodes for the elo/elo-plus DMA engines.
Renamed the interrupt controller alias in mpc832x_rdb.dts to ipic so that
its the same as all the other boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch converts the remaining 83xx boards to the dts-v1 format.
This includes the mpc8313_rdb, mpc832x_mds, mpc8323_rdb, mpc8349emitx,
mpc8349emitxgp and the mpc836x_mds.
The mpc8315_rdb mpc834x_mds, mpc837[789]_*, and sbc8349 were already
dts-v1 and only undergo minor changes for the sake of formatting
consistency across the whole group of boards; i.e. the idea being
that you can do a "diff -u board_A.dts board_B.dts" and see something
meaningful.
The general rule I've applied is that entries for values normally
parsed by humans are left in decimal (i.e. IRQ, cache size, clock
rates, basic counts and indexes) and all other data (i.e. reg and
ranges, IRQ flags etc.) remain in hex.
I've used dtc to confirm that the output prior to this changeset
matches the output after this changeset is applied for all boards.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also:
- rename "fsl_spi" to "fsl,spi";
- add and use cell-index property, if found;
- split probing code out of fsl_spi_init, thus we can call
it for legacy device_type probing and new "compatible" probing.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
...thus use fixed-link to register proper "Fixed PHY"
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds localbus and pata nodes to use CF IDE interface
on MPC8349E-mITX boards.
Patch also adds code to probe localbus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove device_type = "usb" for 83xx SoC USB controller
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added aliases nodes for kurobox, 83xx, 85xx, and 86xx platforms.
This included added labels and cell-index properties for serial and
pci nodes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Removed address fields in ethernet nodes
* Removed #address-cells, #size-cells from gianfar nodes
* Added cell-index to gianfar and ucc ethernet nodes
* Added enet[0..3] labels
* Renamed compatible node for gianfar mdio to "fsl,gianfar-mdio"
* Removed device_type = "mdio"
The matching for gianfar mdio still supports the old "mdio"/"gianfar" combo
but it is now considered deprecated.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
According to booting-without-of.txt, compatible should be "fsl_spi" and
mode "cpu" or "qe" for the fsl SPI controllers.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Setup dr_mode for USB-DR to peripheral as the default (host mode) doesn't make
much sense for the mini-AB connector on the ITX board.
Peripheral mode is preferable to OTG as the fsl_usb2_udc.c driver doesn't yet
properly support it.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
cuImage needs to know the logical index of the ethernet devices in order
to assign mac addresses. This adds the needed properties.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
CC: Scott Wood <scottwood@freescale.com>
CC: Kumar Gala <galak@kernel.crashing.org>
CC: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updated the device trees to have the PCI nodes be at the same level as
the SOC node. This is to make it so that the SOC nodes children address
space is just on chip registers and not other bus memory as well.
Also, for PCIe nodes added a P2P bridge to handle the virtual P2P bridge
that exists in the PHB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Removed the following cruft from .dts files:
* 32-bit in cpu node -- doesn't exist in any spec and not used by kernel
* removed built-in (chrp legacy)
* Removed #interrupt-cells in places they don't need to be set
* Fixed ranges on lite5200*
* Removed clock-frequency from i8259 pic node, not sure where this came from
* Removed big-endian from i8259 pic nodes, this was just bogus
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updated the 83xx & 85xx device tree PCI related compartible property.
Used the following compatible properties:
PCI "fsl,mpc8349-pci"
PCI "fsl,mpc8540-pci"
PCI-X: "fsl,mpc8540-pcix"
PCIe: "fsl,mpc8548-pcie"
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For the 83xx, 85xx, and 86xx device trees, add a "local-mac-address" property
to every Ethernet node that didn't have one. Add a comment indicating that
the "address" and/or "mac-address" properties are deprecated in DTS files
and will be removed at a later time. Change all MAC address properties to
have a zero MAC address value.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The #cpus property is unused and undocumented and is therefore
being removed.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Fixed up top level compatible property for all boards
* Removed explicit linux,phandle usage. Use references and labels now
* Fixed interrupt sense attribute, some interrupts were marked edge, that are level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the DTS for the Freescale MPC 8349E-mITX reference board. Contact
Vitesse for the driver for the VSC 7385.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Anton Vorontsov
Linus Torvalds
Andy Fleming
Paul Mackerras
John Rigby
Kumar Gala
Kim Phillips
Paul Gortmaker
Vitaly Bordug
Li Yang
Peter Korsgaard
Grant Likely
Roy Zang
Timur Tabi
Stuart Yoder