This commit converts the PMC support code to a platform driver. Because
the boot process needs to call into this driver very early, also set up
a minimal environment via an early initcall.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Instead of using a simple variable access to get at the Tegra chip ID,
use a function so that we can run additional code. This can be used to
determine where the chip ID is being accessed without being available.
That in turn will be handy for resolving boot sequence dependencies in
order to convert more code to regular initcalls rather than a sequence
fixed by Tegra SoC setup code.
Signed-off-by: Thierry Reding <treding@nvidia.com>
If these aren't sorted alphabetically, then the logical choice is to
append new ones, however that creates a lot of potential for conflicts
because every change will then add new includes in the same location.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When booting secondary CPU(s) which are not yet powergated, a wrong
check lead to a timeout after 100 jiffies. With this patch, we only
delay powergating if CPUs are still not powered yet.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add Tegra124 SoC support that base on CortexA15MP Core. And enable the
SMP function that can re-use the same procedure with Tegra114.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This branch includes a number of enhancements to core SoC support for
Tegra devices. The major new features are:
* Adds a new CPU-power-gated cpuidle state for Tegra114.
* Adds initial system suspend support for Tegra114, initially supporting
just CPU-power-gating during suspend.
* Adds "LP1" suspend mode support for all of Tegra20/30/114. This mode
both gates CPU power, and places the DRAM into self-refresh mode.
* A new DT-driven PCIe driver to Tegra20/30. The driver is also moved
from arch/arm/mach-tegra/ to drivers/pci/host/.
The PCIe driver work depends on the following tag from Thomas Petazzoni:
git://git.infradead.org/linux-mvebu.git mis-3.12.2
... which is merged into the middle of this pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ve9i
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From: Stephen Warren:
ARM: tegra: core SoC enhancements for 3.12
This branch includes a number of enhancements to core SoC support for
Tegra devices. The major new features are:
* Adds a new CPU-power-gated cpuidle state for Tegra114.
* Adds initial system suspend support for Tegra114, initially supporting
just CPU-power-gating during suspend.
* Adds "LP1" suspend mode support for all of Tegra20/30/114. This mode
both gates CPU power, and places the DRAM into self-refresh mode.
* A new DT-driven PCIe driver to Tegra20/30. The driver is also moved
from arch/arm/mach-tegra/ to drivers/pci/host/.
The PCIe driver work depends on the following tag from Thomas Petazzoni:
git://git.infradead.org/linux-mvebu.git mis-3.12.2
... which is merged into the middle of this pull request.
* tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (33 commits)
ARM: tegra: disable LP2 cpuidle state if PCIe is enabled
MAINTAINERS: Add myself as Tegra PCIe maintainer
PCI: tegra: set up PADS_REFCLK_CFG1
PCI: tegra: Add Tegra 30 PCIe support
PCI: tegra: Move PCIe driver to drivers/pci/host
PCI: msi: add default MSI operations for !HAVE_GENERIC_HARDIRQS platforms
ARM: tegra: add LP1 suspend support for Tegra114
ARM: tegra: add LP1 suspend support for Tegra20
ARM: tegra: add LP1 suspend support for Tegra30
ARM: tegra: add common LP1 suspend support
clk: tegra114: add LP1 suspend/resume support
ARM: tegra: config the polarity of the request of sys clock
ARM: tegra: add common resume handling code for LP1 resuming
ARM: pci: add ->add_bus() and ->remove_bus() hooks to hw_pci
of: pci: add registry of MSI chips
PCI: Introduce new MSI chip infrastructure
PCI: remove ARCH_SUPPORTS_MSI kconfig option
PCI: use weak functions for MSI arch-specific functions
ARM: tegra: unify Tegra's Kconfig a bit more
ARM: tegra: remove the limitation that Tegra114 can't support suspend
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This reverts commit 510bb59 "ARM: tegra: add cpu_disable for hotplug".
The Tegra114 support CPU0 hotplug function in HW physically, but it needs
other software to make it work normally after we add CPU idle power down
mode support. So remove them for now.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
This removes all the ARM uses of the __cpuinit macros from C code,
and all __CPUINIT from assembly code. It also had two ".previous"
section statements that were paired off against __CPUINIT
(aka .section ".cpuinit.text") that also get removed here.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The Tegra114 could hotplug the CPU0, but the common cpu_disable didn't
support that. Adding a Tegra specific cpu_disable function for it.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
[swarren: adjusted the switch statement to be future-proof]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
For Tegra114, once the CPUs were powered up by PMC in cold boot flow. The
flow controller will maintain the power state and control power sequence
for each CPU by setting event trigger (e.g. CPU hotplug ,idle and
suspend power down/up).
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Pull ARM updates from Russell King:
"The major items included in here are:
- MCPM, multi-cluster power management, part of the infrastructure
required for ARMs big.LITTLE support.
- A rework of the ARM KVM code to allow re-use by ARM64.
- Error handling cleanups of the IS_ERR_OR_NULL() madness and fixes
of that stuff for arch/arm
- Preparatory patches for Cortex-M3 support from Uwe Kleine-König.
There is also a set of three patches in here from Hugh/Catalin to
address freeing of inappropriate page tables on LPAE. You already
have these from akpm, but they were already part of my tree at the
time he sent them, so unfortunately they'll end up with duplicate
commits"
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (77 commits)
ARM: EXYNOS: remove unnecessary use of IS_ERR_VALUE()
ARM: IMX: remove unnecessary use of IS_ERR_VALUE()
ARM: OMAP: use consistent error checking
ARM: cleanup: OMAP hwmod error checking
ARM: 7709/1: mcpm: Add explicit AFLAGS to support v6/v7 multiplatform kernels
ARM: 7700/2: Make cpu_init() notrace
ARM: 7702/1: Set the page table freeing ceiling to TASK_SIZE
ARM: 7701/1: mm: Allow arch code to control the user page table ceiling
ARM: 7703/1: Disable preemption in broadcast_tlb*_a15_erratum()
ARM: mcpm: provide an interface to set the SMP ops at run time
ARM: mcpm: generic SMP secondary bringup and hotplug support
ARM: mcpm_head.S: vlock-based first man election
ARM: mcpm: Add baremetal voting mutexes
ARM: mcpm: introduce helpers for platform coherency exit/setup
ARM: mcpm: introduce the CPU/cluster power API
ARM: multi-cluster PM: secondary kernel entry code
ARM: cacheflush: add synchronization helpers for mixed cache state accesses
ARM: cpu hotplug: remove majority of cache flushing from platforms
ARM: smp: flush L1 cache in cpu_die()
ARM: tegra: remove tegra specific cpu_disable()
...
Merge in the gic cleanup since it has a handful of annoying internal conflicts
with soc development branches. All of them are delete/delete conflicts.
* gic/cleanup:
irqchip: vic: add include of linux/irq.h
irqchip: gic: Perform the gic_secondary_init() call via CPU notifier
irqchip: gic: Call handle_bad_irq() directly
arm: Move chained_irq_(enter|exit) to a generic file
arm: Move the set_handle_irq and handle_arch_irq declarations to asm/irq.h
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-shmobile/smp-emev2.c
arch/arm/mach-shmobile/smp-r8a7779.c
arch/arm/mach-shmobile/smp-sh73a0.c
arch/arm/mach-socfpga/platsmp.c
The tegra cpu_disable() function is the same as the generic version
in arch/arm/kernel/smp.c. Therefore, it can be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All the calls to gic_secondary_init() pass 0 as the first argument.
Since this function is called on each CPU when starting, it can be done
in a platform-independent way via a CPU notifier registered by the GIC
code.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Tested-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Barry Song <baohua.song@csr.com>
The secondary CPU can be brought up by toggling the power in PMC. Then
the flow controller will release CPU to go by clearing the reset and
clamp signal automatically.
Based on the work by:
Bo Yan <byan@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Using the CPU power on function in PMC driver to bring up secondary CPUs,
because we are going to re-factor powergate driver to support generic
power domain. It will be removed later and added the generic power domain
support in PMC driver.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
"tegra_boot_secondary()" has many condition branches for some Tegra
SoC generations in a single function so that it's not easy to compile
a kernel only for a single SoC if one wants with some reason, debug
purpose(?). This patch provides SoC specific version of
boot_secondary(), tegra{20,30}_boot_secondary(). This could allow
any combination of SoC to be built. Those boot_secondary functions can
be preparation when we ntroduce chip specific function pointers in the
future without having chip dependent branches around.
Also removed unused definition/prototpye.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
[josephl: remove the Tegra114 part of the original patch]
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The warm boot sequence of Tegra30 secondary CPUs should wait for the
power ready then removing the clamps.
This did not fix any known or unknown issue, but nice to have this fix.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Check a return value for tegra_powergate_remove_clamping().
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Based on two separate cleanup branches, it's now empty and can be removed.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Stephen Warren <swarren@wwwdotorg.org>
This pull request adds initial support for the Tegra114 SoC, which
integrates a quad-core ARM Cortex-A15 CPU. I'm proud to observe that we
posted the initial versions of these patches before the final official
announcement of this chip.
These patches are enough to boot with a UART-based console, support the
Dalmore and Pluto reference/evaluation boards, instantiate the GPIO and
pinctrl drivers, and enable a cpuidle state. As yet, no clocks or
storage devices are supported, but patches for those will follow shortly.
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-cpuidle, followed by a merge of the previous pull
request with tag tegra-for-3.9-scu-base-rework.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bIIe
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-t114' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stepen Warren:
ARM: tegra: add Tegra114 SoC support
This pull request adds initial support for the Tegra114 SoC, which
integrates a quad-core ARM Cortex-A15 CPU. I'm proud to observe that we
posted the initial versions of these patches before the final official
announcement of this chip.
These patches are enough to boot with a UART-based console, support the
Dalmore and Pluto reference/evaluation boards, instantiate the GPIO and
pinctrl drivers, and enable a cpuidle state. As yet, no clocks or
storage devices are supported, but patches for those will follow shortly.
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-cpuidle, followed by a merge of the previous pull
request with tag tegra-for-3.9-scu-base-rework.
* tag 'tegra-for-3.9-soc-t114' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (24 commits)
ARM: DT: tegra114: add pinmux DT entry
ARM: DT: tegra114: add GPIO DT entry
ARM: tegra114: select PINCTRL for Tegra114 SoC
ARM: tegra: add Tegra114 ARM_CPUIDLE_WFI_STATE support
ARM: tegra: Add SMMU entry to Tegra114 DT
ARM: tegra: add AHB entry to Tegra114 DT
ARM: tegra: Add initial support for Tegra114 SoC.
ARM: dt: tegra114: Add new board, Pluto
ARM: dt: tegra114: Add new board, Dalmore
ARM: dt: tegra114: Add new SoC base, Tegra114 SoC
ARM: tegra: fuse: Add chip ID Tegra114 0x35
ARM: OMAP: Make use of available scu_a9_get_base() interface
ARM: tegra: Skip scu_enable(scu_base) if not Cortex A9
ARM: Add API to detect SCU base address from CP15
ARM: tegra: Use DT /cpu node to detect number of CPU core
ARM: tegra: Add CPU nodes to Tegra30 device tree
ARM: tegra: Add CPU nodes to Tegra20 device tree
ARM: perf: simplify __hw_perf_event_init err handling
ARM: perf: remove unnecessary checks for idx < 0
ARM: perf: handle armpmu_register failing
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove/add conflict in arch/arm/mach-tegra/common.c resolved.
Remove/remove conflict in arch/arm/mach-tegra/platsmp.c. Leave the empty
stub function for now since removing it in the merge commit is confusing;
will be cleaned up in a separate commit. # # It looks like you may be
committing a merge. # If this is not correct, please remove the file #
.git/MERGE_HEAD # and try again.
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s9hz
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: Common Clock Framework rework
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
* tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (31 commits)
clk: tegra30: remove unused TEGRA_CLK_DUPLICATE()s
clk: tegra20: remove unused TEGRA_CLK_DUPLICATE()s
ARM: tegra30: remove auxdata
ARM: tegra20: remove auxdata
ASoC: tegra: remove auxdata
staging: nvec: remove use of clk_get_sys
ARM: tegra: paz00: add clock information to DT
ARM: tegra: add clock properties to Tegra30 DT
ARM: tegra: add clock properties to Tegra20 DT
spi: tegra: do not use clock name to get clock
ARM: tegra: remove legacy clock code
ARM: tegra: migrate to new clock code
clk: tegra: add clock support for Tegra30
clk: tegra: add clock support for Tegra20
clk: tegra: add Tegra specific clocks
ARM: tegra: define Tegra30 CAR binding
ARM: tegra: define Tegra20 CAR binding
ARM: tegra: move tegra_cpu_car.h to linux/clk/tegra.h
ARM: tegra: add function to read chipid
ARM: tegra: fix compile error when disable CPU_IDLE
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-tegra/common.c
arch/arm/mach-tegra/platsmp.c
drivers/clocksource/Makefile
tegra_cpu_car_ops struct is going to be accessed from drivers/clk/tegra.
Move the tegra_cpu_car_ops to include/linux/clk/tegra.h.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
It would rather to use the API of time_to_jiffies than a constant number
of jiffies for the wait time of CPU power up.
Based on the work by:
Sang-Hun Lee <sanlee@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The reset handler code is used for either UP or SMP. To make Tegra device
can compile for UP. It needs to be moved to another file that is not SMP
only. This is because the reset handler also be needed by CPU idle
"powered-down" mode. So we also need to put the reset handler init function
in non-SMP only and init them always.
And currently the implementation of the reset handler to know which CPU is
OK to bring up was identital with "cpu_present_mask". But the
"cpu_present_mask" did not initialize yet when the reset handler init
function was moved to init early function. We use the "cpu_possible_mask"
to replace "cpu_present_mask". Then it can work on both UP and SMP case.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
[swarren: dropped the move of v7_invalidate_l1() from one file to another,
to avoid conflicts with Pavel's cleanup of this function, adjust Makefile
so each line only contains 1 file.]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Skip scu_enable(scu_base) if CPU is not Cortex A9 with SCU.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
SCU based detection only works with Cortex-A9 MP and it doesn't
support ones with multiple clusters. The only way to detect number of
CPU core correctly is with DT /cpu node.
Tegra SoCs decided to use DT detection as the only way and to not use
SCU based detection at all. Even if DT /cpu node based detection
fails, it continues with a single core
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The tegra_cpu_die was be executed by the CPU itslf. So the clock gating
procedure won't be executed after the CPU hardware shutdown code. Moving
the clock gating procedure to tegra_cpu_kill that will be run by another
CPU after the CPU died.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The power up sequence is different on the cold boot CPU and the CPU
that resumed from the hotplug. For the cold boot CPU, it was been power
gated as default. To power up the cold boot CPU, the power should be
un-gated by un toggling the power gate register manually.
For the CPU that resumed from the hotplug, after un-halted the CPU. The
flow controller will un-gate the power of the CPU. No need to manually
control, just wait the power be resumed and continue the power up
sequence after the CPU power is ready.
Based on the work by:
Varun Wadekar <vwadekar@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Now that we have GIC moved to drivers/irqchip and all GIC DT init for
platforms using irqchip_init, move gic.h and update the remaining
includes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
In preparation of moving gic code to drivers/irqchip, remove the direct
platform dependencies on gic_raise_softirq. Move the setup of
smp_cross_call into the gic code and use arch_send_wakeup_ipi_mask
function to trigger wake-up IPIs.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Nothing outside mach-tegra uses this file, so there's no need for it to
be in <mach/>.
Since uncompress.h and debug-macro.S remain in include/mach, they need
to include "../../iomap.h" becaue of this change. uncompress.h will soon
be deleted in later multi-platform/single-zImage patches. debug-macro.S
will need to continue to include this header using an explicit relative
path, to avoid duplicating the physical->virtual address mapping that
iomap.h dictates.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This should make it easier to delete or move <mach/*.h>; something that
is useful for single-zImage.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Replacing the code that directly access to CAR registers with
tegra_cpu_car_ops. This ops hides CPU CAR access inside and
provides control interface for it.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Convert Tegra to use struct smp_operations to provide its SMP
and CPU hotplug operations.
Tested on Harmony.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add support for bringing up secondary cores on Tegra30. On Tegra30 secondary
CPU cores are powergated, so we need to turn on the domains before we can bring
the CPU cores online. Bringing secondary cores online happens early during the
sytem boot, so we call powergating initialization from platform early_init
function.
Based on work by:
Scott Williams <scwilliams@nvidia.com>
Colin Cross <ccross@android.com>
Alex Frid <afrid@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Prepare the Tegra secondary CPU core bringup code for other Tegra variants.
The reset handler is also generalized to allow for future introduction of
powersaving modes which turn off the CPU cores.
Based on work by:
Scott Williams <scwilliams@nvidia.com>
Chris Johnson <cwj@nvidia.com>
Colin Cross <ccross@android.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Rather than clipping the number of CPUs using the compile-time NR_CPUS
constant, use the runtime nr_cpu_ids value instead. This allows the
nr_cpus command line option to work as expected.
Cc: <stable@kernel.org>
Reported-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
cpu_set() is marked as obsolete cpumask function and we plan to
remove it in future.
This patch replace it with modern cpumask function.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-tegra@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Colin Cross <ccross@android.com>
Remove some includes of mach/hardware.h which are not needed. hardware.h
will be removed completely for tegra and cns3xxx in follow on patch.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
If an ARM system has multiple cpus in the same socket and the
kernel is booted with maxcpus=1, secondary cpus are possible but
not present due to how platform_smp_prepare_cpus() is called.
Since most typical ARM processors don't actually support physical
hotplug, initialize the present map to be equal to the possible
map in generic ARM SMP code. Also, always call
platform_smp_prepare_cpus() as long as max_cpus is non-zero (0
means no SMP) to allow platform code to do any SMP setup.
After applying this patch it's possible to boot an ARM system
with maxcpus=1 on the command line and then hotplug in secondary
cpus via sysfs. This is more in line with how x86 does things.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than having each platform class provide a mach/smp.h header for
smp_cross_call(), arrange for them to register the function with the
core ARM SMP code instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All platforms call trace_hardirqs_off() in their secondary startup code,
so move this into the core SMP code - it doesn't need to be in the
per-platform code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a certain amount of smp_prepare_cpus() which doesn't belong
in the platform support code - that is, code which is invariant to the
SMP implementation. Move this code into arch/arm/kernel/smp.c, and
add a platform_ prefix to the original function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Milo is an old boot loader, which is no longer relevant for these
platforms. References to it are misleading. Move the code out
of poke_milo(), and remove references to milo in comments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Thierry Reding
Stefan Agner
Joseph Lo
Kevin Hilman
Paul Gortmaker
Linus Torvalds
Olof Johansson
Russell King
Catalin Marinas
Hiroshi Doyu
Stephen Warren
Prashant Gaikwad
Rob Herring
Marc Zyngier
Peter De Schrijver
KOSAKI Motohiro
Stephen Boyd