It no longer translates to "real irqs" (aka. INO buckets)
so reflect that by using a simpler name for it.
Signed-off-by: David S. Miller <davem@davemloft.net>
All the users go through virt_irq_to_bucket() and essentially
want to go from a virt_irq to an INO, but we have a way
to do that already via virt_to_real_irq_table[].dev_ino.
This also allows us to kill both virt_to_real_irq() and
virt_irq_to_bucket().
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a place to stick INO information in the
virt_to_real_irq_table[], which is currently only used for VIRQs.
And that is readily accessible from the one __irq_ino() call site.
Signed-off-by: David S. Miller <davem@davemloft.net>
We were simply concatenating the devhandle and devino and using that
as the cookie, which defeats the entire purpose of the VIRQ hypervisor
interfaces.
Now that we use physical addresses for the INO buckets, we can
allocate them dynamically for VIRQs and encode the cookies as
~__pa(bucket). This allows us to test for and decode the cookie with
a simple:
brlz $reg1, 1f
xnor $reg1, %g0, $reg2
sequence.
This works because bit 64 is never set in traditional
INO vectors, and it is also never set in a physical
address. So xnor'ing the physical address of the bucket
always gives us a negative number, and thus a unique
condition we can test cheaply.
Inspired by ideas from Greg Onufer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we chain IVEC entries using 32-bit "pointers"
because we know that the ivector_table is in the main
kernel image, thus below 4GB.
This uses proper 64-bit pointers instead.
Whilst this bloats up the kernel image size, this sets
the infrastructure necessary to significantly shrink the
kernel size by using physical addresses and dynamically
allocating the ivector table.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some typos led to using %i6/%i7 instead of %l6/%l7 in loads which is
really really bad because those are the frame pointer and return PC.
Based upon a raid5 crash report by Bertrand Joel.
Signed-off-by: David S. Miller <davem@davemloft.net>
This also makes us use the MSI queues correctly.
Each MSI queue is serviced by a normal sun4u/sun4v INO interrupt
handler. This handler runs the MSI queue and dispatches the
virtual interrupts indicated by arriving MSIs in that MSI queue.
All of the common logic is placed in pci_msi.c, with callbacks to
handle the PCI controller specific aspects of the operations.
This common infrastructure will make it much easier to add MSG
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer initialise the name field of the of_platform_driver, but
use the name field of the embedded device_driver's name field instead.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to Tom Callaway for the excellent bug report and
test case.
sys_ipc() has several problems, most to due with semaphore
call handling:
1) 'err' return should be a 'long'
2) "union semun" is passed in a register on 64-bit compared
to 32-bit which provides it on the stack and therefore
by reference
3) Second and third arguments to SEMCTL are swapped compared
to 32-bit.
Signed-off-by: David S. Miller <davem@davemloft.net>
The name field of of_platform_driver is just copied into the
included device_driver. By not overriding an already initialised
device_driver name, we can convert the drivers over time to stop using
the of_platform_driver name.
Also we were not copying the owner field from of_platform_driver, so do
the same with it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply a consistent format to vmlinux.lds.
The file is now to some degree readable.
In addition move several labels inside the braces
such that they reflect the actual start address of a section.
Without this the label would not reflect if ld added alignment.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The support code is identical to the hypervisor sun4v stuff,
just replacing the hypervisor calls with register reads and
writes in the Fire controller.
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Don't take semaphore in cpufreq_quick_get()
[CPUFREQ] Support different families in fid/did to frequency conversion
[CPUFREQ] cpufreq_stats: misc cpuinit section annotations
[CPUFREQ] implement !CONFIG_CPU_FREQ stub for cpufreq_unregister_notifier()
[CPUFREQ] mark hotplug notifier callback as __cpuinit
[CPUFREQ] Only check for transition latency on problematic governors (kconfig fix)
[CPUFREQ] allow ondemand and conservative cpufreq governors to be used as default
[CPUFREQ] move policy's governor initialisation out of low-level drivers into cpufreq core
[CPUFREQ] Longhaul - Add support for PM133 northbridge
[CPUFREQ] x86: use num_online_nodes to get physical cpus numbers for
This patch makes most of the generic device layer network
namespace safe. This patch makes dev_base_head a
network namespace variable, and then it picks up
a few associated variables. The functions:
dev_getbyhwaddr
dev_getfirsthwbytype
dev_get_by_flags
dev_get_by_name
__dev_get_by_name
dev_get_by_index
__dev_get_by_index
dev_ioctl
dev_ethtool
dev_load
wireless_process_ioctl
were modified to take a network namespace argument, and
deal with it.
vlan_ioctl_set and brioctl_set were modified so their
hooks will receive a network namespace argument.
So basically anthing in the core of the network stack that was
affected to by the change of dev_base was modified to handle
multiple network namespaces. The rest of the network stack was
simply modified to explicitly use &init_net the initial network
namespace. This can be fixed when those components of the network
stack are modified to handle multiple network namespaces.
For now the ifindex generator is left global.
Fundametally ifindex numbers are per namespace, or else
we will have corner case problems with migration when
we get that far.
At the same time there are assumptions in the network stack
that the ifindex of a network device won't change. Making
the ifindex number global seems a good compromise until
the network stack can cope with ifindex changes when
you change namespaces, and the like.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Check the return value of fork_idle() to catch error.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCI-E slot on T1000 connects directly to the Fire PCI chip with no
intervening bridges visible in the OBP tree.
Unfortunately the bus numbering of the device in that slot is
different (2) from the PCI host controller (0), and thus the
pci_bus_{read,write}_config_*() calls don't work out.
Complicating things further the Fire PCI controller has no config
space it responds to either.
For now treat this case specially so that devices in the slot work.
Longer term we need to perhaps cons up a dummy bridge between the Fire
and the PCI-E slot so that the bus hierarchy is complete inside of the
kernel and thus the bus numbering all works out right.
Signed-off-by: David S. Miller <davem@davemloft.net>
We should only use ports underneath "domain-services", other DS ports
in the MDESC aren't for us to use.
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't matter for use in 64-bit objects, but when used in
32-bit environments the top 32-bits of the local and in
registers will get chopped off on the next register window
spill/restore which leads to difficult to track down and
subtle bugs.
Signed-off-by: David S. Miller <davem@davemloft.net>
For the case where the source is not aligned modulo 8
we don't use load-twins to suck the data in and this
kills performance since normal loads allocate in the
L1 cache (unlike load-twin) and thus big memcpys swipe
the entire L1 D-cache.
We need to allocate a register window to implement this
properly, but that actually simplifies a lot of things
as a nice side-effect.
Signed-off-by: David S. Miller <davem@davemloft.net>
argv and envp are pointers to u32's in userspace, so don't
try to put_user() a NULL to them.
Aparently gcc-4.2.x now warns about this, and since we use
-Werror for arch/sparc64 code, this breaks the build.
Signed-off-by: David S. Miller <davem@davemloft.net>
If of_get_property() fails, it returns NULL and the 'len'
parameter is undefined. So we need to explicitly set len
to zero in such cases.
Noticed by Al Viro.
Signed-off-by: David S. Miller <davem@davemloft.net>
When NR_CPUS is smaller than the cpu probed, let the user
know that the cpu won't be used.
Suggested by Al Viro.
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted by Al Viro, when we try to call prom_set_trap_table()
in the SMP trampoline code we try to take the PROM call spinlock
which doesn't work because the current thread pointer isn't
valid yet and lockdep depends upon that being correct.
Furthermore, we cannot set the current thread pointer register
because it can't be properly dereferenced until we return from
prom_set_trap_table(). Kernel TLB misses only work after that
call.
So do the PROM call to set the trap table directly instead of
going through the OBP library C code, and thus avoid the lock
altogether.
These calls are guarenteed to be serialized fully.
Since there are now no calls to the prom_set_trap_table{_sun4v}()
library functions, they can be deleted.
Signed-off-by: David S. Miller <davem@davemloft.net>
On the root PCI bus, the OBP device tree lists device 3 twice.
Once as 'pm' and once as 'lomp'.
Everything goes downhill from there.
Ignore the second instance to workaround this.
Thanks to Kövedi_Krisztián for the bug report and
testing the fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
For hugepage mappings, the file offset, like the address and size, needs to
be aligned to the size of a hugepage.
In commit 68589bc353, the check for this was
moved into prepare_hugepage_range() along with the address and size checks.
But since BenH's rework of the get_unmapped_area() paths leading up to
commit 4b1d89290b, prepare_hugepage_range()
is only called for MAP_FIXED mappings, not for other mappings. This means
we're no longer ever checking for an aligned offset - I've confirmed that
mmap() will (apparently) succeed with a misaligned offset on both powerpc
and i386 at least.
This patch restores the check, removing it from prepare_hugepage_range()
and putting it back into hugetlbfs_file_mmap(). I'm putting it there,
rather than in the get_unmapped_area() path so it only needs to go in one
place, than separately in the half-dozen or so arch-specific
implementations of hugetlb_get_unmapped_area().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Adam Litke <agl@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1) sun4{u,v}_build_msi() have improper return value handling.
We should always return negative error codes, instead of
using the magic value "0" which could in fact be a valid
MSI number.
2) sun4{u,v}_build_msi() should return -ENOMEM instead of
calling prom_prom() halt with kzalloc() of the interrupt
data fails.
3) We 'remembered' the MSI number using a singleton in the
struct device archdata area, this doesn't work for MSI-X
which can cause multiple MSIs assosciated with one device.
Delete that archdata member, and instead store the MSI
number in the IRQ chip data area.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes we were using 32-bit values and the top bits were
getting inadvertantly chopped off. This will matter for the
forthcoming Fire controller MSI support.
Signed-off-by: David S. Miller <davem@davemloft.net>
This register is not a part of the sun4v architecture.
Niagara 1 and 2 happened to leave it around.
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the OF device tree, it's useful to let userland get
at the machine description so it can pretty print the
graph etc.
The implementation is a simple MISC device with a read method.
Signed-off-by: David S. Miller <davem@davemloft.net>
Every time a cpu is added via hotplug, we allocate the per-cpu MONDO
queues but we never free them up. Freeing isn't easy since the first
cpu gets this memory from bootmem.
Therefore, the simplest thing to do to fix this bug is to allocate the
queues for all possible cpus at boot time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the cpu type in the OBP device tree before committing to
using the optimized Niagara memcpy and memset implementation.
If we don't recognize the cpu type, use a completely generic
version.
Signed-off-by: David S. Miller <davem@davemloft.net>
It didn't handle that case at all, and now dump_stack()
can be implemented directly as show_stack(current, NULL)
Signed-off-by: David S. Miller <davem@davemloft.net>
Fully unify all of the DMA ops so that subordinate bus types to
the DMA operation providers (such as ebus, isa, of_device) can
work transparently.
Basically, we just make sure that for every system device we
create, the dev->archdata 'iommu' and 'stc' fields are filled
in.
Then we have two platform variants of the DMA ops, one for SUN4U which
actually programs the real hardware, and one for SUN4V which makes
hypervisor calls.
This also fixes the crashes in parport_pc on sparc64, reported by
Meelis Roos.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't provide fake PCI config space for sun4u.
Also, put back the funny host controller space handling that
at least Sabre needs. You have to read PCI host controller
registers at their nature size otherwise you get zeros instead
of correct values.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller
Stephen Rothwell
Sam Ravnborg
Linus Torvalds
Eric W. Biederman
Thomas Renninger
Akinobu Mita
David S. Miller
David Gibson
David S. Miller
Alexey Dobriyan