[ Upstream commit 8ef1ba39a9 ]
This is similar to commit e6186820a7 ("arm64: dts: rockchip: Arch
counter doesn't tick in system suspend"). Specifically on the rk3288
it can be seen that the timer stops ticking in suspend if we end up
running through the "osc_disable" path in rk3288_slp_mode_set(). In
that path the 24 MHz clock will turn off and the timer stops.
To test this, I ran this on a Chrome OS filesystem:
before=$(date); \
suspend_stress_test -c1 --suspend_min=30 --suspend_max=31; \
echo ${before}; date
...and I found that unless I plug in a device that requests USB wakeup
to be active that the two calls to "date" would show that fewer than
30 seconds passed.
NOTE: deep suspend (where the 24 MHz clock gets disabled) isn't
supported yet on upstream Linux so this was tested on a downstream
kernel.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99fa066710 ]
When I try to boot rk3288-veyron-mickey I totally fail to make the
eMMC work. Specifically my logs (on Chrome OS 4.19):
mmc_host mmc1: card is non-removable.
mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
mmc1: switch to bus width 8 failed
mmc1: switch to bus width 4 failed
mmc1: new high speed MMC card at address 0001
mmcblk1: mmc1:0001 HAG2e 14.7 GiB
mmcblk1boot0: mmc1:0001 HAG2e partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 HAG2e partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 HAG2e partition 3 4.00 MiB, chardev (243:0)
mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
mmc1: switch to bus width 8 failed
mmc1: switch to bus width 4 failed
mmc1: tried to HW reset card, got error -110
mmcblk1: error -110 requesting status
mmcblk1: recovery failed!
print_req_error: I/O error, dev mmcblk1, sector 0
...
When I remove the '/delete-property/mmc-hs200-1_8v' then everything is
hunky dory.
That line comes from the original submission of the mickey dts
upstream, so presumably at the time the HS200 was failing and just
enumerating things as a high speed device was fine. ...or maybe it's
just that some mickey devices work when enumerating at "high speed",
just not mine?
In any case, hs200 seems good now. Let's turn it on.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1c04790234 ]
As some point hs200 was failing on rk3288-veyron-minnie. See commit
9849267811 ("ARM: dts: rockchip: temporarily remove emmc hs200 speed
from rk3288 minnie"). Although I didn't track down exactly when it
started working, it seems to work OK now, so let's turn it back on.
To test this, I booted from SD card and then used this script to
stress the enumeration process after fixing a memory leak [1]:
cd /sys/bus/platform/drivers/dwmmc_rockchip
for i in $(seq 1 3000); do
echo "========================" $i
echo ff0f0000.dwmmc > unbind
sleep .5
echo ff0f0000.dwmmc > bind
while true; do
if [ -e /dev/mmcblk2 ]; then
break;
fi
sleep .1
done
done
It worked fine.
[1] https://lkml.kernel.org/r/20190503233526.226272-1-dianders@chromium.org
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ffd9a1ba9f ]
DMA got broken a while back in two different ways:
1) a change in the behaviour of disable_irq() to wait for the interrupt
to finish executing causes us to deadlock at the end of DMA.
2) a change to avoid modifying the scatterlist left the first transfer
uninitialised.
DMA is only used with expansion cards, so has gone unnoticed.
Fixes: fa4e998999 ("[ARM] dma: RiscPC: don't modify DMA SG entries")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 24951465cb upstream.
arch/arm/ defines a SIGMINSTKSZ of 2k, so we should use the same value
for compat tasks.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Reported-by: Steve McIntyre <steve.mcintyre@arm.com>
Tested-by: Steve McIntyre <93sam@debian.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c737abc193 upstream.
Armada-37xx UART0 registers are 0x200 bytes wide. Right next to them are
the UART1 registers that should not be declared in this node.
Update the example in DT bindings document accordingly.
Signed-off-by: allen yan <yanwei@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f16d80b75a upstream.
On systems like P9 powernv where we have no TM (or P8 booted with
ppc_tm=off), userspace can construct a signal context which still has
the MSR TS bits set. The kernel tries to restore this context which
results in the following crash:
Unexpected TM Bad Thing exception at c0000000000022fc (msr 0x8000000102a03031) tm_scratch=800000020280f033
Oops: Unrecoverable exception, sig: 6 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in:
CPU: 0 PID: 1636 Comm: sigfuz Not tainted 5.2.0-11043-g0a8ad0ffa4 #69
NIP: c0000000000022fc LR: 00007fffb2d67e48 CTR: 0000000000000000
REGS: c00000003fffbd70 TRAP: 0700 Not tainted (5.2.0-11045-g7142b497d8)
MSR: 8000000102a03031 <SF,VEC,VSX,FP,ME,IR,DR,LE,TM[E]> CR: 42004242 XER: 00000000
CFAR: c0000000000022e0 IRQMASK: 0
GPR00: 0000000000000072 00007fffb2b6e560 00007fffb2d87f00 0000000000000669
GPR04: 00007fffb2b6e728 0000000000000000 0000000000000000 00007fffb2b6f2a8
GPR08: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR12: 0000000000000000 00007fffb2b76900 0000000000000000 0000000000000000
GPR16: 00007fffb2370000 00007fffb2d84390 00007fffea3a15ac 000001000a250420
GPR20: 00007fffb2b6f260 0000000010001770 0000000000000000 0000000000000000
GPR24: 00007fffb2d843a0 00007fffea3a14a0 0000000000010000 0000000000800000
GPR28: 00007fffea3a14d8 00000000003d0f00 0000000000000000 00007fffb2b6e728
NIP [c0000000000022fc] rfi_flush_fallback+0x7c/0x80
LR [00007fffb2d67e48] 0x7fffb2d67e48
Call Trace:
Instruction dump:
e96a0220 e96a02a8 e96a0330 e96a03b8 394a0400 4200ffdc 7d2903a6 e92d0c00
e94d0c08 e96d0c10 e82d0c18 7db242a6 <4c000024> 7db243a6 7db142a6 f82d0c18
The problem is the signal code assumes TM is enabled when
CONFIG_PPC_TRANSACTIONAL_MEM is enabled. This may not be the case as
with P9 powernv or if `ppc_tm=off` is used on P8.
This means any local user can crash the system.
Fix the problem by returning a bad stack frame to the user if they try
to set the MSR TS bits with sigreturn() on systems where TM is not
supported.
Found with sigfuz kernel selftest on P9.
This fixes CVE-2019-13648.
Fixes: 2b0a576d15 ("powerpc: Add new transactional memory state to the signal context")
Cc: stable@vger.kernel.org # v3.9
Reported-by: Praveen Pandey <Praveen.Pandey@in.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190719050502.405-1-mikey@neuling.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4d202c8c8e upstream.
xive_find_target_in_mask() has the following for(;;) loop which has a
bug when @first == cpumask_first(@mask) and condition 1 fails to hold
for every CPU in @mask. In this case we loop forever in the for-loop.
first = cpu;
for (;;) {
if (cpu_online(cpu) && xive_try_pick_target(cpu)) // condition 1
return cpu;
cpu = cpumask_next(cpu, mask);
if (cpu == first) // condition 2
break;
if (cpu >= nr_cpu_ids) // condition 3
cpu = cpumask_first(mask);
}
This is because, when @first == cpumask_first(@mask), we never hit the
condition 2 (cpu == first) since prior to this check, we would have
executed "cpu = cpumask_next(cpu, mask)" which will set the value of
@cpu to a value greater than @first or to nr_cpus_ids. When this is
coupled with the fact that condition 1 is not met, we will never exit
this loop.
This was discovered by the hard-lockup detector while running LTP test
concurrently with SMT switch tests.
watchdog: CPU 12 detected hard LOCKUP on other CPUs 68
watchdog: CPU 12 TB:85587019220796, last SMP heartbeat TB:85578827223399 (15999ms ago)
watchdog: CPU 68 Hard LOCKUP
watchdog: CPU 68 TB:85587019361273, last heartbeat TB:85576815065016 (19930ms ago)
CPU: 68 PID: 45050 Comm: hxediag Kdump: loaded Not tainted 4.18.0-100.el8.ppc64le #1
NIP: c0000000006f5578 LR: c000000000cba9ec CTR: 0000000000000000
REGS: c000201fff3c7d80 TRAP: 0100 Not tainted (4.18.0-100.el8.ppc64le)
MSR: 9000000002883033 <SF,HV,VEC,VSX,FP,ME,IR,DR,RI,LE> CR: 24028424 XER: 00000000
CFAR: c0000000006f558c IRQMASK: 1
GPR00: c0000000000afc58 c000201c01c43400 c0000000015ce500 c000201cae26ec18
GPR04: 0000000000000800 0000000000000540 0000000000000800 00000000000000f8
GPR08: 0000000000000020 00000000000000a8 0000000080000000 c00800001a1beed8
GPR12: c0000000000b1410 c000201fff7f4c00 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000540 0000000000000001
GPR20: 0000000000000048 0000000010110000 c00800001a1e3780 c000201cae26ed18
GPR24: 0000000000000000 c000201cae26ed8c 0000000000000001 c000000001116bc0
GPR28: c000000001601ee8 c000000001602494 c000201cae26ec18 000000000000001f
NIP [c0000000006f5578] find_next_bit+0x38/0x90
LR [c000000000cba9ec] cpumask_next+0x2c/0x50
Call Trace:
[c000201c01c43400] [c000201cae26ec18] 0xc000201cae26ec18 (unreliable)
[c000201c01c43420] [c0000000000afc58] xive_find_target_in_mask+0x1b8/0x240
[c000201c01c43470] [c0000000000b0228] xive_pick_irq_target.isra.3+0x168/0x1f0
[c000201c01c435c0] [c0000000000b1470] xive_irq_startup+0x60/0x260
[c000201c01c43640] [c0000000001d8328] __irq_startup+0x58/0xf0
[c000201c01c43670] [c0000000001d844c] irq_startup+0x8c/0x1a0
[c000201c01c436b0] [c0000000001d57b0] __setup_irq+0x9f0/0xa90
[c000201c01c43760] [c0000000001d5aa0] request_threaded_irq+0x140/0x220
[c000201c01c437d0] [c00800001a17b3d4] bnx2x_nic_load+0x188c/0x3040 [bnx2x]
[c000201c01c43950] [c00800001a187c44] bnx2x_self_test+0x1fc/0x1f70 [bnx2x]
[c000201c01c43a90] [c000000000adc748] dev_ethtool+0x11d8/0x2cb0
[c000201c01c43b60] [c000000000b0b61c] dev_ioctl+0x5ac/0xa50
[c000201c01c43bf0] [c000000000a8d4ec] sock_do_ioctl+0xbc/0x1b0
[c000201c01c43c60] [c000000000a8dfb8] sock_ioctl+0x258/0x4f0
[c000201c01c43d20] [c0000000004c9704] do_vfs_ioctl+0xd4/0xa70
[c000201c01c43de0] [c0000000004ca274] sys_ioctl+0xc4/0x160
[c000201c01c43e30] [c00000000000b388] system_call+0x5c/0x70
Instruction dump:
78aad182 54a806be 3920ffff 78a50664 794a1f24 7d294036 7d43502a 7d295039
4182001c 48000034 78a9d182 79291f24 <7d23482a> 2fa90000 409e0020 38a50040
To fix this, move the check for condition 2 after the check for
condition 3, so that we are able to break out of the loop soon after
iterating through all the CPUs in the @mask in the problem case. Use
do..while() to achieve this.
Fixes: 243e25112d ("powerpc/xive: Native exploitation of the XIVE interrupt controller")
Cc: stable@vger.kernel.org # v4.12+
Reported-by: Indira P. Joga <indira.priya@in.ibm.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1563359724-13931-1-git-send-email-ego@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 517c3ba009 upstream.
X86_HYPER_NATIVE isn't accurate for checking if running on native platform,
e.g. CONFIG_HYPERVISOR_GUEST isn't set or "nopv" is enabled.
Checking the CPU feature bit X86_FEATURE_HYPERVISOR to determine if it's
running on native platform is more accurate.
This still doesn't cover the platforms on which X86_FEATURE_HYPERVISOR is
unsupported, e.g. VMware, but there is nothing which can be done about this
scenario.
Fixes: 8a4b06d391 ("x86/speculation/mds: Add sysfs reporting for MDS")
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1564022349-17338-1-git-send-email-zhenzhong.duan@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d02f1aa391 upstream.
Some Lenovo 2-in-1s with a detachable keyboard have a portrait screen but
advertise a landscape resolution and pitch, resulting in a messed up
display if the kernel tries to show anything on the efifb (because of the
wrong pitch).
Fix this by adding a new DMI match table for devices which need to have
their width and height swapped.
At first it was tried to use the existing table for overriding some of the
efifb parameters, but some of the affected devices have variants with
different LCD resolutions which will not work with hardcoded override
values.
Reference: https://bugzilla.redhat.com/show_bug.cgi?id=1730783
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190721152418.11644-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88dddc11a8 upstream.
If a KVM guest is reset while running a nested guest, free_nested will
disable the shadow VMCS execution control in the vmcs01. However,
on the next KVM_RUN vmx_vcpu_run would nevertheless try to sync
the VMCS12 to the shadow VMCS which has since been freed.
This causes a vmptrld of a NULL pointer on my machime, but Jan reports
the host to hang altogether. Let's see how much this trivial patch fixes.
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Liran Alon <liran.alon@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 733f0025f0 ]
When building drm/exynos for sh, as part of an allmodconfig build, the
following warning triggered:
exynos7_drm_decon.c: In function `decon_remove':
exynos7_drm_decon.c:769:24: warning: unused variable `ctx'
struct decon_context *ctx = dev_get_drvdata(&pdev->dev);
The ctx variable is only used as argument to iounmap().
In sh - allmodconfig CONFIG_MMU is not defined
so it ended up in:
\#define __iounmap(addr) do { } while (0)
\#define iounmap __iounmap
Fix the warning by introducing a static inline function for iounmap.
This is similar to several other architectures.
Link: http://lkml.kernel.org/r/20190622114208.24427-1-sam@ravnborg.org
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3343962068 ]
In commit 4a7b06c157a2 ("powerpc/eeh: Handle hugepages in ioremap
space") support for using hugepages in the vmalloc and ioremap areas was
enabled for radix. Unfortunately this broke EEH MMIO error checking.
Detection works by inserting a hook which checks the results of the
ioreadXX() set of functions. When a read returns a 0xFFs response we
need to check for an error which we do by mapping the (virtual) MMIO
address back to a physical address, then mapping physical address to a
PCI device via an interval tree.
When translating virt -> phys we currently assume the ioremap space is
only populated by PAGE_SIZE mappings. If a hugepage mapping is found we
emit a WARN_ON(), but otherwise handles the check as though a normal
page was found. In pathalogical cases such as copying a buffer
containing a lot of 0xFFs from BAR memory this can result in the system
not booting because it's too busy printing WARN_ON()s.
There's no real reason to assume huge pages can't be present and we're
prefectly capable of handling them, so do that.
Fixes: 4a7b06c157a2 ("powerpc/eeh: Handle hugepages in ioremap space")
Reported-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190710150517.27114-1-oohall@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e005b761e ]
The next commit will make the way of passing CONFIG options more robust.
Unfortunately, it would uncover another hidden issue; without this
commit, skiroot_defconfig would be broken like this:
| WRAP arch/powerpc/boot/zImage.pseries
| arch/powerpc/boot/wrapper.a(decompress.o): In function `bcj_powerpc.isra.10':
| decompress.c:(.text+0x720): undefined reference to `get_unaligned_be32'
| decompress.c:(.text+0x7a8): undefined reference to `put_unaligned_be32'
| make[1]: *** [arch/powerpc/boot/Makefile;383: arch/powerpc/boot/zImage.pseries] Error 1
| make: *** [arch/powerpc/Makefile;295: zImage] Error 2
skiroot_defconfig is the only defconfig that enables CONFIG_KERNEL_XZ
for ppc, which has never been correctly built before.
I figured out the root cause in lib/decompress_unxz.c:
| #ifdef CONFIG_PPC
| # define XZ_DEC_POWERPC
| #endif
CONFIG_PPC is undefined here in the ppc bootwrapper because autoconf.h
is not included except by arch/powerpc/boot/serial.c
XZ_DEC_POWERPC is not defined, therefore, bcj_powerpc() is not compiled
for the bootwrapper.
With the next commit passing CONFIG_PPC correctly, we would realize that
{get,put}_unaligned_be32 was missing.
Unlike the other decompressors, the ppc bootwrapper duplicates all the
necessary helpers in arch/powerpc/boot/.
The other architectures define __KERNEL__ and pull in helpers for
building the decompressors.
If ppc bootwrapper had defined __KERNEL__, lib/xz/xz_private.h would
have included <asm/unaligned.h>:
| #ifdef __KERNEL__
| # include <linux/xz.h>
| # include <linux/kernel.h>
| # include <asm/unaligned.h>
However, doing so would cause tons of definition conflicts since the
bootwrapper has duplicated everything.
I just added copies of {get,put}_unaligned_be32, following the
bootwrapper coding convention.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190705100144.28785-1-yamada.masahiro@socionext.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ab3a0689e ]
When testing out gpio-keys with a button, a spurious
interrupt (and therefore a key press or release event)
gets triggered as soon as the driver enables the irq
line for the first time.
This patch clears any potential bogus generated interrupt
that was caused by the switching of the associated irq's
type and polarity.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80bf6ceaf9 ]
When we get into activate_mm(), lockdep complains that we're doing
something strange:
WARNING: possible circular locking dependency detected
5.1.0-10252-gb00152307319-dirty #121 Not tainted
------------------------------------------------------
inside.sh/366 is trying to acquire lock:
(____ptrval____) (&(&p->alloc_lock)->rlock){+.+.}, at: flush_old_exec+0x703/0x8d7
but task is already holding lock:
(____ptrval____) (&mm->mmap_sem){++++}, at: flush_old_exec+0x6c5/0x8d7
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&mm->mmap_sem){++++}:
[...]
__lock_acquire+0x12ab/0x139f
lock_acquire+0x155/0x18e
down_write+0x3f/0x98
flush_old_exec+0x748/0x8d7
load_elf_binary+0x2ca/0xddb
[...]
-> #0 (&(&p->alloc_lock)->rlock){+.+.}:
[...]
__lock_acquire+0x12ab/0x139f
lock_acquire+0x155/0x18e
_raw_spin_lock+0x30/0x83
flush_old_exec+0x703/0x8d7
load_elf_binary+0x2ca/0xddb
[...]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&mm->mmap_sem);
lock(&(&p->alloc_lock)->rlock);
lock(&mm->mmap_sem);
lock(&(&p->alloc_lock)->rlock);
*** DEADLOCK ***
2 locks held by inside.sh/366:
#0: (____ptrval____) (&sig->cred_guard_mutex){+.+.}, at: __do_execve_file+0x12d/0x869
#1: (____ptrval____) (&mm->mmap_sem){++++}, at: flush_old_exec+0x6c5/0x8d7
stack backtrace:
CPU: 0 PID: 366 Comm: inside.sh Not tainted 5.1.0-10252-gb00152307319-dirty #121
Stack:
[...]
Call Trace:
[<600420de>] show_stack+0x13b/0x155
[<6048906b>] dump_stack+0x2a/0x2c
[<6009ae64>] print_circular_bug+0x332/0x343
[<6009c5c6>] check_prev_add+0x669/0xdad
[<600a06b4>] __lock_acquire+0x12ab/0x139f
[<6009f3d0>] lock_acquire+0x155/0x18e
[<604a07e0>] _raw_spin_lock+0x30/0x83
[<60151e6a>] flush_old_exec+0x703/0x8d7
[<601a8eb8>] load_elf_binary+0x2ca/0xddb
[...]
I think it's because in exec_mmap() we have
down_read(&old_mm->mmap_sem);
...
task_lock(tsk);
...
activate_mm(active_mm, mm);
(which does down_write(&mm->mmap_sem))
I'm not really sure why lockdep throws in the whole knowledge
about the task lock, but it seems that old_mm and mm shouldn't
ever be the same (and it doesn't deadlock) so tell lockdep that
they're different.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aaf06665f7 ]
Commit ed49f7fd64 ("powerpc/xmon: Disable tracing when entering
xmon") added code to disable recording trace entries while in xmon. The
commit introduced a variable 'tracing_enabled' to record if tracing was
enabled on xmon entry, and used this to conditionally enable tracing
during exit from xmon.
However, we are not checking the value of 'fromipi' variable in
xmon_core() when setting 'tracing_enabled'. Due to this, when secondary
cpus enter xmon, they will see tracing as being disabled already and
tracing won't be re-enabled on exit. Fix the same.
Fixes: ed49f7fd64 ("powerpc/xmon: Disable tracing when entering xmon")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df5be5be87 ]
When the firmware does PCI BAR resource allocation, it passes the assigned
addresses and flags (prefetch/64bit/...) via the "reg" property of
a PCI device device tree node so the kernel does not need to do
resource allocation.
The flags are stored in resource::flags - the lower byte stores
PCI_BASE_ADDRESS_SPACE/etc bits and the other bytes are IORESOURCE_IO/etc.
Some flags from PCI_BASE_ADDRESS_xxx and IORESOURCE_xxx are duplicated,
such as PCI_BASE_ADDRESS_MEM_PREFETCH/PCI_BASE_ADDRESS_MEM_TYPE_64/etc.
When parsing the "reg" property, we copy the prefetch flag but we skip
on PCI_BASE_ADDRESS_MEM_TYPE_64 which leaves the flags out of sync.
The missing IORESOURCE_MEM_64 flag comes into play under 2 conditions:
1. we remove PCI_PROBE_ONLY for pseries (by hacking pSeries_setup_arch()
or by passing "/chosen/linux,pci-probe-only");
2. we request resource alignment (by passing pci=resource_alignment=
via the kernel cmd line to request PAGE_SIZE alignment or defining
ppc_md.pcibios_default_alignment which returns anything but 0). Note that
the alignment requests are ignored if PCI_PROBE_ONLY is enabled.
With 1) and 2), the generic PCI code in the kernel unconditionally
decides to:
- reassign the BARs in pci_specified_resource_alignment() (works fine)
- write new BARs to the device - this fails for 64bit BARs as the generic
code looks at IORESOURCE_MEM_64 (not set) and writes only lower 32bits
of the BAR and leaves the upper 32bit unmodified which breaks BAR mapping
in the hypervisor.
This fixes the issue by copying the flag. This is useful if we want to
enforce certain BAR alignment per platform as handling subpage sized BARs
is proven to cause problems with hotplug (SLOF already aligns BARs to 64k).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Shawn Anastasio <shawn@anastas.io>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e59a175faa ]
CPU online/offline code paths are sensitive to parts of the device
tree (various cpu node properties, cache nodes) that can be changed as
a result of a migration.
Prevent CPU hotplug while the device tree potentially is inconsistent.
Fixes: 410bccf978 ("powerpc/pseries: Partition migration in the kernel")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 812af43303 ]
Current logic iterates over CPUID Fn8000001d leafs (Cache Properties)
to detect the last level cache, and derive the last-level cache ID.
However, this information is already available in the cpu_llc_id.
Therefore, make use of it instead.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Link: http://lkml.kernel.org/r/1524864877-111962-3-git-send-email-suravee.suthikulpanit@amd.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1323c3b72a upstream.
The pin mappings introduced in commit 636f8ba67f
("MIPS: JZ4740: Qi LB60: Add pinctrl configuration for several drivers")
are completely wrong. The pinctrl driver name is incorrect, and the
function and group fields are swapped.
Fixes: 636f8ba67f ("MIPS: JZ4740: Qi LB60: Add pinctrl configuration for several drivers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: od@zcrc.me
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f474c28fbc upstream.
powerpc hardware triggers watchpoint before executing the instruction.
To make trigger-after-execute behavior, kernel emulates the
instruction. If the instruction is 'load something into non-volatile
register', exception handler should restore emulated register state
while returning back, otherwise there will be register state
corruption. eg, adding a watchpoint on a list can corrput the list:
# cat /proc/kallsyms | grep kthread_create_list
c00000000121c8b8 d kthread_create_list
Add watchpoint on kthread_create_list->prev:
# perf record -e mem:0xc00000000121c8c0
Run some workload such that new kthread gets invoked. eg, I just
logged out from console:
list_add corruption. next->prev should be prev (c000000001214e00), \
but was c00000000121c8b8. (next=c00000000121c8b8).
WARNING: CPU: 59 PID: 309 at lib/list_debug.c:25 __list_add_valid+0xb4/0xc0
CPU: 59 PID: 309 Comm: kworker/59:0 Kdump: loaded Not tainted 5.1.0-rc7+ #69
...
NIP __list_add_valid+0xb4/0xc0
LR __list_add_valid+0xb0/0xc0
Call Trace:
__list_add_valid+0xb0/0xc0 (unreliable)
__kthread_create_on_node+0xe0/0x260
kthread_create_on_node+0x34/0x50
create_worker+0xe8/0x260
worker_thread+0x444/0x560
kthread+0x160/0x1a0
ret_from_kernel_thread+0x5c/0x70
List corruption happened because it uses 'load into non-volatile
register' instruction:
Snippet from __kthread_create_on_node:
c000000000136be8: addis r29,r2,-19
c000000000136bec: ld r29,31424(r29)
if (!__list_add_valid(new, prev, next))
c000000000136bf0: mr r3,r30
c000000000136bf4: mr r5,r28
c000000000136bf8: mr r4,r29
c000000000136bfc: bl c00000000059a2f8 <__list_add_valid+0x8>
Register state from WARN_ON():
GPR00: c00000000059a3a0 c000007ff23afb50 c000000001344e00 0000000000000075
GPR04: 0000000000000000 0000000000000000 0000001852af8bc1 0000000000000000
GPR08: 0000000000000001 0000000000000007 0000000000000006 00000000000004aa
GPR12: 0000000000000000 c000007ffffeb080 c000000000137038 c000005ff62aaa00
GPR16: 0000000000000000 0000000000000000 c000007fffbe7600 c000007fffbe7370
GPR20: c000007fffbe7320 c000007fffbe7300 c000000001373a00 0000000000000000
GPR24: fffffffffffffef7 c00000000012e320 c000007ff23afcb0 c000000000cb8628
GPR28: c00000000121c8b8 c000000001214e00 c000007fef5b17e8 c000007fef5b17c0
Watchpoint hit at 0xc000000000136bec.
addis r29,r2,-19
=> r29 = 0xc000000001344e00 + (-19 << 16)
=> r29 = 0xc000000001214e00
ld r29,31424(r29)
=> r29 = *(0xc000000001214e00 + 31424)
=> r29 = *(0xc00000000121c8c0)
0xc00000000121c8c0 is where we placed a watchpoint and thus this
instruction was emulated by emulate_step. But because handle_dabr_fault
did not restore emulated register state, r29 still contains stale
value in above register state.
Fixes: 5aae8a5370 ("powerpc, hw_breakpoints: Implement hw_breakpoints for 64-bit server processors")
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Cc: stable@vger.kernel.org # 2.6.36+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ecb78ef56 upstream.
Previously, only IBAT1 and IBAT2 were used to map kernel linear mem.
Since commit 63b2bc6195 ("powerpc/mm/32s: Use BATs for
STRICT_KERNEL_RWX"), we may have all 8 BATs used for mapping
kernel text. But the suspend/restore functions only save/restore
BATs 0 to 3, and clears BATs 4 to 7.
Make suspend and restore functions respectively save and reload
the 8 BATs on CPUs having MMU_FTR_USE_HIGH_BATS feature.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10835c8546 upstream.
On parisc the privilege level of a process is stored in the lowest two bits of
the instruction pointers (IAOQ0 and IAOQ1). On Linux we use privilege level 0
for the kernel and privilege level 3 for user-space. So userspace should not be
allowed to modify IAOQ0 or IAOQ1 of a ptraced process to change it's privilege
level to e.g. 0 to try to gain kernel privileges.
This patch prevents such modifications by always setting the two lowest bits to
one (which relates to privilege level 3 for user-space) if IAOQ0 or IAOQ1 are
modified via ptrace calls in the native and compat ptrace paths.
Link: https://bugs.gentoo.org/481768
Reported-by: Jeroen Roovers <jer@gentoo.org>
Cc: <stable@vger.kernel.org>
Tested-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 34c32fc603 upstream.
On parisc the privilege level of a process is stored in the lowest two bits of
the instruction pointers (IAOQ0 and IAOQ1). On Linux we use privilege level 0
for the kernel and privilege level 3 for user-space. So userspace should not be
allowed to modify IAOQ0 or IAOQ1 of a ptraced process to change it's privilege
level to e.g. 0 to try to gain kernel privileges.
This patch prevents such modifications in the regset support functions by
always setting the two lowest bits to one (which relates to privilege level 3
for user-space) if IAOQ0 or IAOQ1 are modified via ptrace regset calls.
Link: https://bugs.gentoo.org/481768
Cc: <stable@vger.kernel.org> # v4.7+
Tested-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16f4641166 upstream.
The following commit:
d7cbbe49a9 ("perf/x86/amd/uncore: Set ThreadMask and SliceMask for L3 Cache perf events")
enables L3 PMC events for all threads and slices by writing 1's in
'ChL3PmcCfg' (L3 PMC PERF_CTL) register fields.
Those bitfields overlap with high order event select bits in the Data
Fabric PMC control register, however.
So when a user requests raw Data Fabric events (-e amd_df/event=0xYYY/),
the two highest order bits get inadvertently set, changing the counter
select to events that don't exist, and for which no counts are read.
This patch changes the logic to write the L3 masks only when dealing
with L3 PMC counters.
AMD Family 16h and below Northbridge (NB) counters were not affected.
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Gary Hook <Gary.Hook@amd.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Liska <mliska@suse.cz>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pu Wen <puwen@hygon.cn>
Cc: Stephane Eranian <eranian@google.com>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: d7cbbe49a9 ("perf/x86/amd/uncore: Set ThreadMask and SliceMask for L3 Cache perf events")
Link: https://lkml.kernel.org/r/20190628215906.4276-1-kim.phillips@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e74bd96989 upstream.
When default_get_smp_config() is called with early == 1 and mpf->feature1
is non-zero, mpf is leaked because the return path does not do
early_memunmap().
Fix this and share a common exit routine.
Fixes: 5997efb967 ("x86/boot: Use memremap() to map the MPF and MPC data")
Reported-by: Cfir Cohen <cfir@google.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1907091942570.28240@chino.kir.corp.google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba24eee668 upstream.
The Tegra AGIC interrupt controller is an ARM GIC400 interrupt
controller. Per the ARM GIC device-tree binding, the first address
region is for the GIC distributor registers and the second address
region is for the GIC CPU interface registers. The address space for
the distributor registers is 4kB, but currently this is incorrectly
defined as 8kB for the Tegra AGIC and overlaps with the CPU interface
registers. Correct the address space for the distributor to be 4kB.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Fixes: bcdbde4335 ("arm64: tegra: Add AGIC node for Tegra210")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6fc3977ccc upstream.
If a perf_event creation fails due to any reason of the host perf
subsystem, it has no chance to log the corresponding event for guest
which may cause abnormal sampling data in guest result. In debug mode,
this message helps to understand the state of vPMC and we may not
limit the number of occurrences but not in a spamming style.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ece6031ece upstream.
The GPU regulator enable ramp delay for Jetson TX1 is set to 1ms which
not sufficient because the enable ramp delay has been measured to be
greater than 1ms. Furthermore, the downstream kernels released by NVIDIA
for Jetson TX1 are using a enable ramp delay 2ms and a settling delay of
160us. Update the GPU regulator enable ramp delay for Jetson TX1 to be
2ms and add a settling delay of 160us.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Fixes: 5e6b9a89af ("arm64: tegra: Add VDD_GPU regulator to Jetson TX1")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6bd934de1e upstream.
The sha256-ce finup implementation for ARM64 produces wrong digest
for empty input (len=0). Expected: the actual digest, result: initial
value of SHA internal state. The error is in sha256_ce_finup:
for empty data `finalize` will be 1, so the code is relying on
sha2_ce_transform to make the final round. However, in
sha256_base_do_update, the block function will not be called when
len == 0.
Fix it by setting finalize to 0 if data is empty.
Fixes: 03802f6a80 ("crypto: arm64/sha2-ce - move SHA-224/256 ARMv8 implementation to base layer")
Cc: stable@vger.kernel.org
Signed-off-by: Elena Petrova <lenaptr@google.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d4aaf16de upstream.
The sha1-ce finup implementation for ARM64 produces wrong digest
for empty input (len=0). Expected: da39a3ee..., result: 67452301...
(initial value of SHA internal state). The error is in sha1_ce_finup:
for empty data `finalize` will be 1, so the code is relying on
sha1_ce_transform to make the final round. However, in
sha1_base_do_update, the block function will not be called when
len == 0.
Fix it by setting finalize to 0 if data is empty.
Fixes: 07eb54d306 ("crypto: arm64/sha1-ce - move SHA-1 ARMv8 implementation to base layer")
Cc: stable@vger.kernel.org
Signed-off-by: Elena Petrova <lenaptr@google.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bc53d3d777 ]
Without 'set -e', shell scripts continue running even after any
error occurs. The missed 'set -e' is a typical bug in shell scripting.
For example, when a disk space shortage occurs while this script is
running, it actually ends up with generating a truncated capflags.c.
Yet, mkcapflags.sh continues running and exits with 0. So, the build
system assumes it has succeeded.
It will not be re-generated in the next invocation of Make since its
timestamp is newer than that of any of the source files.
Add 'set -e' so that any error in this script is caught and propagated
to the build system.
Since 9c2af1c737 ("kbuild: add .DELETE_ON_ERROR special target"),
make automatically deletes the target on any failure. So, the broken
capflags.c will be deleted automatically.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: https://lkml.kernel.org/r/20190625072622.17679-1-yamada.masahiro@socionext.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2af22f3ec3 ]
Some Qualcomm Snapdragon based laptops built to run Microsoft Windows
are clearly ACPI 5.1 based, given that that is the first ACPI revision
that supports ARM, and introduced the FADT 'arm_boot_flags' field,
which has a non-zero field on those systems.
So in these cases, infer from the ARM boot flags that the FADT must be
5.1 or later, and treat it as 5.1.
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Graeme Gregory <graeme.gregory@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69d927bba3 ]
Recent probing at the Linux Kernel Memory Model uncovered a
'surprise'. Strongly ordered architectures where the atomic RmW
primitive implies full memory ordering and
smp_mb__{before,after}_atomic() are a simple barrier() (such as x86)
fail for:
*x = 1;
atomic_inc(u);
smp_mb__after_atomic();
r0 = *y;
Because, while the atomic_inc() implies memory order, it
(surprisingly) does not provide a compiler barrier. This then allows
the compiler to re-order like so:
atomic_inc(u);
*x = 1;
smp_mb__after_atomic();
r0 = *y;
Which the CPU is then allowed to re-order (under TSO rules) like:
atomic_inc(u);
r0 = *y;
*x = 1;
And this very much was not intended. Therefore strengthen the atomic
RmW ops to include a compiler barrier.
NOTE: atomic_{or,and,xor} and the bitops already had the compiler
barrier.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbb99c0f58 ]
Add the CPUID enumeration for Intel's de-feature bits to accommodate
passing these de-features through to kvm guests.
These de-features are (from SDM vol 1, section 8.1.8):
- X86_FEATURE_FDP_EXCPTN_ONLY: If CPUID.(EAX=07H,ECX=0H):EBX[bit 6] = 1, the
data pointer (FDP) is updated only for the x87 non-control instructions that
incur unmasked x87 exceptions.
- X86_FEATURE_ZERO_FCS_FDS: If CPUID.(EAX=07H,ECX=0H):EBX[bit 13] = 1, the
processor deprecates FCS and FDS; it saves each as 0000H.
Signed-off-by: Aaron Lewis <aaronlewis@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jim Mattson <jmattson@google.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Frederic Weisbecker <frederic@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: marcorr@google.com
Cc: Peter Feiner <pfeiner@google.com>
Cc: pshier@google.com
Cc: Robert Hoo <robert.hu@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Lendacky <Thomas.Lendacky@amd.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190605220252.103406-1-aaronlewis@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa69fb62be ]
After r363059 and r363928 in LLVM, a build using ld.lld as the linker
with CONFIG_RANDOMIZE_BASE enabled fails like so:
ld.lld: error: relocation R_AARCH64_ABS32 cannot be used against symbol
__efistub_stext_offset; recompile with -fPIC
Fangrui and Peter figured out that ld.lld is incorrectly considering
__efistub_stext_offset as a relative symbol because of the order in
which symbols are evaluated. _text is treated as an absolute symbol
and stext is a relative symbol, making __efistub_stext_offset a
relative symbol.
Adding ABSOLUTE will force ld.lld to evalute this expression in the
right context and does not change ld.bfd's behavior. ld.lld will
need to be fixed but the developers do not see a quick or simple fix
without some research (see the linked issue for further explanation).
Add this simple workaround so that ld.lld can continue to link kernels.
Link: https://github.com/ClangBuiltLinux/linux/issues/561
Link: 025a815d75
Link: 249fde8583
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Debugged-by: Fangrui Song <maskray@google.com>
Debugged-by: Peter Smith <peter.smith@linaro.org>
Suggested-by: Fangrui Song <maskray@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
[will: add comment]
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1196364f21 ]
calc_vmlinuz_load_addr.c requires SZ_64K to be defined for alignment
purposes. It included "../../../../include/linux/sizes.h" to define
that size, however "sizes.h" tries to include <linux/const.h> which
assumes linux system headers. These may not exist eg. the following
error was encountered when building Linux for OpenWrt under macOS:
In file included from arch/mips/boot/compressed/calc_vmlinuz_load_addr.c:16:
arch/mips/boot/compressed/../../../../include/linux/sizes.h:11:10: fatal error: 'linux/const.h' file not found
^~~~~~~~~~
Change makefile to force building on local linux headers instead of
system headers. Also change eye-watering relative reference in include
file spec.
Thanks to Jo-Philip Wich & Petr Štetiar for assistance in tracking this
down & fixing.
Suggested-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db13a5ba27 ]
While trying to get the uart with parity working I found setting even
parity enabled odd parity insted. Fix the register settings to match
the datasheet of AR9331.
A similar patch was created by 8devices, but not sent upstream.
77c5586ade
Signed-off-by: Stefan Hellermann <stefan@the2masters.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4f18d869ff upstream.
The stfle inline assembly returns the number of double words written
(condition code 0) or the double words it would have written
(condition code 3), if the memory array it got as parameter would have
been large enough.
The current stfle implementation assumes that the array is always
large enough and clears those parts of the array that have not been
written to with a subsequent memset call.
If however the array is not large enough memset will get a negative
length parameter, which means that memset clears memory until it gets
an exception and the kernel crashes.
To fix this simply limit the maximum length. Move also the inline
assembly to an extra function to avoid clobbering of register 0, which
might happen because of the added min_t invocation together with code
instrumentation.
The bug was introduced with commit 14375bc4eb ("[S390] cleanup
facility list handling") but was rather harmless, since it would only
write to a rather large array. It became a potential problem with
commit 3ab121ab18 ("[S390] kernel: Add z/VM LGR detection"). Since
then it writes to an array with only four double words, while some
machines already deliver three double words. As soon as machines have
a facility bit within the fifth double a crash on IPL would happen.
Fixes: 14375bc4eb ("[S390] cleanup facility list handling")
Cc: <stable@vger.kernel.org> # v2.6.37+
Reviewed-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd5de2721e upstream.
As kernelci.org reports, this function is not used in
vdk_hs38_defconfig:
arch/arc/kernel/unwind.c:188:14: warning: 'unw_hdr_alloc' defined but not used [-Wunused-function]
Fixes: bc79c9a721 ("ARC: dw2 unwind: Reinstante unwinding out of modules")
Link: https://kernelci.org/build/id/5d1cae3f59b514300340c132/logs/
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 81c7ed296d ]
A kernel which boots in 5-level paging mode crashes in a small percentage
of cases if KASLR is enabled.
This issue was tracked down to the case when the kernel image unpacks in a
way that it crosses an 1G boundary. The crash is caused by an overrun of
the PMD page table in __startup_64() and corruption of P4D page table
allocated next to it. This particular issue is not visible with 4-level
paging as P4D page tables are not used.
But the P4D and the PUD calculation have similar problems.
The PMD index calculation is wrong due to operator precedence, which fails
to confine the PMDs in the PMD array on wrap around.
The P4D calculation for 5-level paging and the PUD calculation calculate
the first index correctly, but then blindly increment it which causes the
same issue when a kernel image is located across a 512G and for 5-level
paging across a 46T boundary.
This wrap around mishandling was introduced when these parts moved from
assembly to C.
Restore it to the correct behaviour.
Fixes: c88d71508e ("x86/boot/64: Rewrite startup_64() in C")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190620112345.28833-1-kirill.shutemov@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27e23d8975 ]
omap3xxx_prm_enable_io_wakeup() is marked __init, but its caller is not, so
we get a warning with clang-8:
WARNING: vmlinux.o(.text+0x343c8): Section mismatch in reference from the function omap3xxx_prm_late_init() to the function .init.text:omap3xxx_prm_enable_io_wakeup()
The function omap3xxx_prm_late_init() references
the function __init omap3xxx_prm_enable_io_wakeup().
This is often because omap3xxx_prm_late_init lacks a __init
annotation or the annotation of omap3xxx_prm_enable_io_wakeup is wrong.
When building with gcc, omap3xxx_prm_enable_io_wakeup() is always
inlined, so we never noticed in the past.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1287533d3d upstream.
When building BPF code using "clang -target bpf -c", clang does not
define __linux__.
To build BPF IR decoders the include linux/lirc.h is needed which
includes linux/types.h. Currently this workaround is needed:
https://git.linuxtv.org/v4l-utils.git/commit/?id=dd3ff81f58c4e1e6f33765dc61ad33c48ae6bb07
This check might otherwise be useful to stop users from using a non-linux
compiler, but if you're doing that you are going to have a lot more
trouble anyway.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21149/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 993773d11d upstream.
The index to access the threads tls array is controlled by userspace
via syscall: sys_ptrace(), hence leading to a potential exploitation
of the Spectre variant 1 vulnerability.
The index can be controlled from:
ptrace -> arch_ptrace -> do_get_thread_area.
Fix this by sanitizing the user supplied index before using it to access
the p->thread.tls_array.
Signed-off-by: Dianzhang Chen <dianzhangchen0@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1561524630-3642-1-git-send-email-dianzhangchen0@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31a2fbb390 upstream.
The index to access the threads ptrace_bps is controlled by userspace via
syscall: sys_ptrace(), hence leading to a potential exploitation of the
Spectre variant 1 vulnerability.
The index can be controlled from:
ptrace -> arch_ptrace -> ptrace_get_debugreg.
Fix this by sanitizing the user supplied index before using it access
thread->ptrace_bps.
Signed-off-by: Dianzhang Chen <dianzhangchen0@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1561476617-3759-1-git-send-email-dianzhangchen0@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Petr Cvek
Douglas Anderson
Russell King
Yoshinori Sato
Will Deacon
allen yan
Michael Neuling
Gautham R. Shenoy
Zhenzhong Duan
Hans de Goede
Paolo Bonzini
Sam Ravnborg
Oliver O'Halloran
Masahiro Yamada
Christian Lamparter
Johannes Berg
Naveen N. Rao
Alexey Kardashevskiy
Nathan Lynch
Suravee Suthikulpanit
Paul Cercueil
Ravi Bangoria
Christophe Leroy
Helge Deller
Kim Phillips
David Rientjes
Jon Hunter
Like Xu
Elena Petrova
Ard Biesheuvel
Peter Zijlstra
Aaron Lewis
Nathan Chancellor
Kevin Darbyshire-Bryant
Stefan Hellermann
Heiko Carstens
Arnd Bergmann
Kirill A. Shutemov
Sébastien Szymanski
Sean Young
Dianzhang Chen