This driver is used across all MSM SoCs. Hence give a generic name.
All Functions and strutures are also using "msm_otg" as prefix.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The hcd->state variable is a disaster. It's not clearly owned by
either usbcore or the host controller drivers, and they both change it
from time to time, potentially stepping on each other's toes. It's
not protected by any locks. And there's no mechanism to prevent it
from going through an invalid transition.
This patch (as1451) takes a first step toward fixing these problems.
As it turns out, usbcore uses hcd->state for essentially only two
things: checking whether the controller's root hub is running and
checking whether the controller has died. Therefore the patch adds
two new atomic bitflags to the hcd structure, to store these pieces of
information. The new flags are used only by usbcore, and a private
spinlock prevents invalid combinations (a dead controller's root hub
cannot be running).
The patch does not change the places where usbcore sets hcd->state,
since HCDs may depend on them. Furthermore, there is one place in
usb_hcd_irq() where usbcore still must use hcd->state: An HCD's
interrupt handler can implicitly indicate that the controller died by
setting hcd->state to HC_STATE_HALT. Nevertheless, the new code is a
big improvement over the current code.
The patch makes one other change. The hcd_bus_suspend() and
hcd_bus_resume() routines now check first whether the host controller
has died; if it has then they return immediately without calling the
HCD's bus_suspend or bus_resume methods.
This fixes the major problem reported in Bugzilla #29902: The system
fails to suspend after a host controller dies during system resume.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alex Terekhov <a.terekhov@gmail.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Macro arguments used in expressions need to be enclosed in parenthesis
to avoid unpleasant surprises.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a driver doesn't know how much data a device is going to send,
the buffer size should be at least as big as the endpoint's maxpacket
value. The serial drivers don't follow this rule; many of them
request only 256-byte bulk-in buffers. As a result, they suffer
overflow errors if a high-speed device wants to send a lot of data,
because high-speed bulk endpoints are required to have a maxpacket
size of 512.
This patch (as1450) fixes the problem by using the driver's
bulk_in_size value as a minimum, always allocating buffers no smaller
than the endpoint's maxpacket size.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Flynn Marquardt <flynn@flynnux.de>
CC: <stable@kernel.org> [after .39-rc1 is out]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Save the last event in the otg_transceiver so that it can used in the
musb driver and gadget driver to configure the musb and enable the
vbus for host mode and OTG mode, if the device is connected during boot.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is needed to resolve some merge conflicts that were found
in the USB host controller patches, and reported by Stephen Rothwell.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (21 commits)
USB: cdc-acm: Adding second ACM channel support for Nokia N8
USB, Mass Storage, composite, gadget: Fix build failure and memset of a struct
USB: Fix trout build failure with ci13xxx_msm gadget
USB: EHCI: fix scheduling while atomic during suspend
USB: usb-storage: unusual_devs entry for Coby MP3 player
USB: ftdi_sio: Add VID=0x0647, PID=0x0100 for Acton Research spectrograph
USB: fix race between root-hub resume and wakeup requests
USB: prevent buggy hubs from crashing the USB stack
usb: r8a66597-udc: Fixed bufnum of Bulk
USB: ftdi_sio: add ST Micro Connect Lite uart support
USB: Storage: Add unusual_devs entry for VTech Kidizoom
USB SL811HS HCD: Fix memory leak in sl811h_urb_enqueue()
USB: ti_usb: fix module removal
USB: io_edgeport: fix the reported firmware major and minor
usb: ehci-omap: Show fatal probing time errors to end user
usb: musb: introduce api for dma code to check compatibility with usb request
usb: musb: maintain three states for buffer mappings instead of two
usb: musb: disable double buffering when it's broken
usb: musb: hsdma: change back to use musb_read/writew
usb: musb: core: fix IRQ check
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
virtio_net: Add schedule check to napi_enable call
x25: Do not reference freed memory.
pch_can: fix tseg1/tseg2 setting issue
isdn: hysdn: Kill (partially buggy) CVS regision log reporting.
can: softing_cs needs slab.h
pch_gbe: Fix the issue which a driver locks when rx offload is set by ethtool
netfilter: nf_conntrack: set conntrack templates again if we return NF_REPEAT
pch_can: fix module reload issue with MSI
pch_can: fix rmmod issue
pch_can: fix 800k comms issue
net: Fix lockdep regression caused by initializing netdev queues too early.
net/caif: Fix dangling list pointer in freed object on error.
USB CDC NCM errata updates for cdc_ncm host driver
CDC NCM errata updates for cdc.h
ixgbe: update version string
ixgbe: cleanup variable initialization
ixgbe: limit VF access to network traffic
ixgbe: fix for 82599 erratum on Header Splitting
ixgbe: fix variable set but not used warnings by gcc 4.6
e1000: add support for Marvell Alaska M88E1118R PHY
...
This patch fixes the below compilation errors.
CC drivers/usb/gadget/ci13xxx_msm.o
CC net/mac80211/led.o
drivers/usb/gadget/ci13xxx_msm.c: In function 'ci13xxx_msm_notify_event':
drivers/usb/gadget/ci13xxx_msm.c:42: error: 'USB_AHBBURST' undeclared (first use in this function)
drivers/usb/gadget/ci13xxx_msm.c:42: error: (Each undeclared identifier is reported only once
drivers/usb/gadget/ci13xxx_msm.c:42: error: for each function it appears in.)
drivers/usb/gadget/ci13xxx_msm.c:43: error: 'USB_AHBMODE' undeclared (first use in this function)
make[4]: *** [drivers/usb/gadget/ci13xxx_msm.o] Error 1
make[3]: *** [drivers/usb/gadget] Error 2
MSM USB driver is not supported on boards like trout (MSM7201) which
has an external PHY.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To compile functionfs userspace driver one needs definitions from
include/linux/usb/functionfs.h. This patch add this file to the list
of includes exported to userspace.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Provide optional hooks for the host controller driver to override the
default DMA mapping and unmapping routines. In general, these shouldn't
be necessary unless the host controller has special DMA requirements,
such as alignment contraints. If these are not specified, the
general usb_hcd_(un)?map_urb_for_dma functions will be used instead.
Also, pass the status to unmap_urb_for_dma so it can know whether the
DMA buffer has been overwritten.
Finally, add a flag to be used by these implementations if they
allocated a temporary buffer so it can be freed properly when unmapping.
Signed-off-by: Robert Morell <rmorell@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The convention is to prefix symbols exported from the USB HCD core with
"usb_hcd". This change makes unmap_urb_setup_for_dma() and
unmap_urb_for_dma() consistent with that.
Signed-off-by: Robert Morell <rmorell@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-linus' of master.kernel.org:/pub/scm/linux/kernel/git/sarah/xhci:
xhci: Remove more doorbell-related reads
xHCI: fix printk_ratelimit() usage
xHCI: replace dev_dbg() with xhci_dbg()
xHCI: fix cycle bit set in giveback_first_trb()
xHCI: remove redundant parameter in giveback_first_trb()
xHCI: fix queue_trb in isoc transfer
xhci: Use GFP_NOIO during device reset.
usb: Realloc xHCI structures after a hub is verified.
xhci: Do not run xhci_cleanup_msix with irq disabled
xHCI: synchronize irq in xhci_suspend()
xhci: Resume bus on any port status change.
Alan's commit 335f8514f2 introduced
.carrier_raised function in several drivers. That also means
tty_port_block_til_ready can now suspend the process trying to open the serial
port when Carrier Detect is low and put it into tty_port.open_wait queue. We
need to wake up the process when Carrier Detect goes high and trigger TTY
hangup when CD goes low.
Some of the devices do not report modem status line changes, or at least we
don't understand the status message, so for those we remove .carrier_raised
again.
Signed-off-by: Libor Pechacek <lpechacek@suse.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Synchronize the interrupts instead of free them in xhci_suspend(). This will
prevent a double free when the host is suspended and then the card removed.
Set the flag hcd->msix_enabled when using MSI-X, and check the flag in
suspend_common(). MSI-X synchronization will be handled by xhci_suspend(),
and MSI/INTx will be synchronized in suspend_common().
This patch should be queued for the 2.6.37 stable tree.
Reported-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
Implement runtime and system pm ops to put hardware into low power
mode (LPM). As part of LPM, USB clocks are turned off, PHY is put
into suspend state and PHY comparators are turned off if VBUS/Id
notifications are not required from PHY.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver implements PHY initialization, clock management, ULPI IO ops
and simple OTG state machine to kick host/peripheral based on Id/VBUS
line status. VBUS/Id lines are tied to a reference voltage on some boards.
Hence provide debugfs interface to select host/peripheral mode.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the NOP USB OTG transceiver driver is built as a module, the otg.h
header declares external functions, but if they are referenced from the
kernel proper, as, e.g., in the OMAP3 case, where the omap3evm board is
calling the usb_nop_xceiv_register() function, linkage breaks. This patch
fixes this problem.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
... we will completely drop that need by
moving clock handling to platform glue
layer. Marking as deprecated will allow
us to catch all users easily.
Signed-off-by: Felipe Balbi <balbi@ti.com>
change all ocurrences of musb_hdrc to musb-hdrc.
We will call glue layer drivers musb-<glue layer>,
so in order to keep things somewhat standard, let's
change the underscore into a dash.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Changes:
include/linux/usb/usbnet.h:
- a new flag to indicate driver's capability to accumulate IP packets in Tx
direction and extract several packets from single skb in Rx direction.
drivers/net/usb/usbnet.c:
- the procedure of counting packets in usbnet was updated due to the
accumulating of IP packets in the driver
- no short packets are sent if indicated by the flag in driver_info
structure
Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds test mode support for Langwell gadget driver.
Signed-off-by: Henry Yuan <hang.yuan@intel.com>
Signed-off-by: Andy Luo <yifei.luo@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding hub SuperSpeed usb definitions as defined by ch10 of the USB3.0
spec.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In order to not touch the driver file for different xtal usage,
push the clkin value to board file and calculate the register
value instead of hardcoding it.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
USB: mct_u232: fix broken close
USB: gadget: amd5536udc.c: fix error path
USB: imx21-hcd - fix off by one resource size calculation
usb: gadget: fix Kconfig warning
usb: r8a66597-udc: Add processing when USB was removed.
mxc_udc: add workaround for ENGcm09152 for i.MX35
USB: ftdi_sio: add device ids for ScienceScope
USB: musb: AM35x: Workaround for fifo read issue
USB: musb: add musb support for AM35x
USB: AM35x: Add musb support
usb: Fix linker errors with CONFIG_PM=n
USB: ohci-sh - use resource_size instead of defining its own resource_len macro
USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
USB: xhci: Fix compile error when CONFIG_PM=n
USB: accept some invalid ep0-maxpacket values
USB: xHCI: PCI power management implementation
USB: xHCI: bus power management implementation
USB: xHCI: port remote wakeup implementation
USB: xHCI: port power management implementation
...
Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.
Adding SuperSpeed usb definitions as defined by ch9 of the USB3.0 spec.
This patch is a preparation for adding SuperSpeed support to the gadget
framework.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Split unmap_urb_for_dma() to allow just the setup buffer
to be unmapped. This allows HCDs to use PIO for the setup
buffer if it is not suitable for DMA.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add empty functions for get/put transceiver functions too, so that
drivers that optionally use them can call them without worrying that
they might not exist, eliminating ifdefs.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB stack maps the buffer for DMA if the controller supports DMA.
MUSB controller can perform DMA as well as PIO transfers.
The buffer needs to be unmapped before CPU can perform
PIO data transfers.
Export unmap_urb_for_dma() so that drivers can perform
the DMA unmapping in a sane way.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The libusual header file is hard to use from code that isn't part
of libusual. As the comment suggests, these definitions are moved to
their own header file, paralleling other USB classes.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
[mina86@mina86.com: updated to use USB_ prefix and added #include guard]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
index 0000000..d7fc910
In usb_cdc_ncm_dpe32 the fields are 32 bit long and according
to usb style (hungarian notation) should be called dwDatagramIndex
and dwDatagramLength (see CDC NCM subclass spec, 3.3.2). Actually,
they were called wDatagramIndex, wDatagramLength.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make a dedicated structure for datagram pointer entry. There is no
explicit declaration in the spec, but it's used by the host
implementation and makes the structure more clear.
Add some missed constants from the spec
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 65e0b49910.
Since the host and gadget implementations are different, there is
no common code for the file, remove for now.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some typos were in the initial commit, make the spelling
according to the spec.
Add some more comments.
Also change constant names according to the style of the rest
of the file
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updated Kconfig for langwell otg transceiver driver.
Add ipc driver(INTEL_SCU_IPC) as a dependency. Driver version is
updated too.
Signed-off-by: Hao Wu <hao.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds one new header file for the common data structure used in
Intel Penwell/Langwell MID Platform OTG Transceiver drivers. After switched
to the common data structure, Langwell/Penwell OTG Transceiver driver will
provide an unified interface to host/client driver.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Hao Wu <hao.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bind function is most of the time only called at init time so there
is no need to save a pointer to it in the configuration structure.
This fixes many section mismatches reported by modpost.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[m.nazarewicz@samsung.com: updated for -next]
Signed-off-by: Michał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bind function is most of the time only called at init time so there
is no need to save a pointer to it in the composite driver structure.
This fixes many section mismatches reported by modpost.
Signed-off-by: Michał Nazarewicz <m.nazarewicz@samsung.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To accomplish this the function to register a gadget driver takes the bind
function as a second argument. To make things clearer rename the function
to resemble platform_driver_probe.
This fixes many section mismatches like
WARNING: drivers/usb/gadget/g_printer.o(.data+0xc): Section mismatch in
reference from the variable printer_driver to the function
.init.text:printer_bind()
The variable printer_driver references
the function __init printer_bind()
All callers are fixed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[m.nazarewicz@samsung.com: added dbgp]
Signed-off-by: Michał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The iManufatcurer, iProduct and iSerialNumber composite module
parameters were only used when the gadget driver registers
strings for manufacturer, product and serial number. If the
gadget never bothered to set corresponding fields in USB device
descriptors those module parameters are ignored.
This commit makes the parameters work even if the strings ID
have not been assigned. It also changes the way IDs are
overridden -- what IDs are overridden is now saved in
usb_composite_dev structure -- which makes it unnecessary to
modify the string tables the way previous code did.
The commit also adds a iProduct and iManufatcurer fields to the
usb_composite_device structure. If they are set, appropriate
strings are reserved and added to device descriptor. This makes
it unnecessary for gadget drivers to maintain code for setting
those. If iProduct is not set it defaults to
usb_composite_device::name; if iManufatcurer is not set
a default "<system> <release> with <gadget-name>" is used.
The last thing is that if needs_serial field of
usb_composite_device is set and user failed to provided
iSerialNumber parameter a warning is issued.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for the USB transceiver driver in the Langwell chipset used
on the Intel MID platforms. It folds up the original patch set which includes
basic support for the device, PHY low power mode (Please notice that there is
a limitation, after we drive VBus down, 2ms delay is required from SCU FW to
sync up OTGSC register with USBCFG register), software timers (the hardware
timers do not work in low power mode), HNP, SRP.
Signed-off-by: Hao Wu <hao.wu@intel.com>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pavankumar Kondeti
Alan Stern
Dmitry Torokhov
Felipe Balbi
Hema HK
Paul Bolle
Greg Kroah-Hartman
Linus Torvalds
Alexey Orishko
Marek Szyprowski
Robert Morell
Libor Pechacek
Andiry Xu
Guennadi Liakhovetski
Luo Andy
Tatyana Brokhman
Bob Liu
Martin Fuzzey
Grazvydas Ignotas
Maulik Mankad
Matthew Wilcox
Yauheni Kaliuta
Hao Wu
Uwe Kleine-König
Michal Nazarewicz
Parirajan Muthalagu