Fix spacing and improve name for 83xx phy following other phy in the
same driver.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add resume/suspend function to qca83xx internal phy.
We can't use the at803x generic function as the documentation lacks of
any support for WoL regs.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For qca8327 internal phy there are 2 different switch variant with 2
different phy id. Add this missing variant so the internal phy can be
correctly identified and fixed.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for qca8327 internal phy needed for correct init of the
switch port. It does use the same qca8337 function and reg just with a
different id.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit was probably not tested on net-next, since it did not
refactor the extra phy id check introduced in commit b856150c80 ("net:
phy: at803x: mask 1000 Base-X link mode").
Fixes: 8887ca5474 ("net: phy: at803x: simplify custom phy id matching")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The at803x driver contains a function, at803x_match_phy_id(), which
tests whether the PHY ID matches the value passed, comparing phy_id
with phydev->phy_id and testing all bits that in the driver's mask.
This is the same test that is used to match the driver, with phy_id
replaced with the driver specified ID, phydev->drv->phy_id.
Hence, we already know the value of the bits being tested if we look
at phydev->drv->phy_id directly, and we do not require a complicated
test to check them. Test directly against phydev->drv->phy_id instead.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflict in net/netfilter/nf_tables_api.c.
Duplicate fix in tools/testing/selftests/net/devlink_port_split.py
- take the net-next version.
skmsg, and L4 bpf - keep the bpf code but remove the flags
and err params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
AR8031/AR8033 have different status registers for copper
and fiber operation. However, the extended status register
is the same for both operation modes.
As a result of that, ESTATUS_1000_XFULL is set to 1 even when
operating in copper TP mode.
Remove this mode from the supported link modes, as this driver
currently only supports copper operation.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the at803x share the same regs, it's assumed they are based on the
same implementation. Make it part of the at803x PHY driver to skip
having redudant code.
Add initial support for qca8k internal PHYs. The internal PHYs requires
special mmd and debug values to be set based on the switch revision
passwd using the dev_flags. Supports output of idle, receive and eee_wake
errors stats.
Some debug values sets can't be translated as the documentation lacks any
reference about them.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean any whitespace errors and fix not aligned define.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit c329e5afb4 ("net: phy: at803x: select correct page on
config init") selects the copper page during probe. This fails if the
copper page was already selected. In this case, the value of the copper
page (which is 1) is propagated through phy_restore_page() and is
finally returned for at803x_probe(). Fix it, by just using the
at803x_page_write() directly.
Also in case of an error, the regulator is not disabled and leads to a
WARN_ON() when the probe fails. This couldn't happen before, because
at803x_parse_dt() was the last call in at803x_probe(). It is hard to
see, that the parse_dt() actually enables the regulator. Thus move the
regulator_enable() to the probe function and undo it in case of an
error.
Fixes: c329e5afb4 ("net: phy: at803x: select correct page on config init")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Atheros AR8031 and AR8033 expose different registers for SGMII/Fiber
as well as the copper side of the PHY depending on the BT_BX_REG_SEL bit
in the chip configure register.
The driver assumes the copper side is selected on probe, but this might
not be the case depending which page was last selected by the
bootloader. Notably, Ubiquiti UniFi bootloaders show this behavior.
Select the copper page when probing to circumvent this.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is what Vladimir says about it:
at803x_aneg_done() keeps the aneg reporting as "not done" even when
the copper-side link was reported as up, but the in-band autoneg has
not finished.
That was the _intended_ behavior when that code was introduced, and
Heiner have said about it [1]:
| That's not nice from the PHY:
| It signals "link up", and if the system asks the PHY for link details,
| then it sheepishly says "well, link is *almost* up".
If the specification of phy_aneg_done behavior does not include
in-band autoneg (and it doesn't), then this piece of code does not
belong here.
The fact that we can no longer trigger this code from phylib is yet
another reason why it fails at its intended (and wrong) purpose and
should be removed.
Removing the SGMII link check, would just keep the call to
genphy_aneg_done(), which is also the fallback. Thus we can just remove
at803x_aneg_done() altogether.
[1] https://lore.kernel.org/netdev/fdf0074a-2572-5914-6f3e-77202cbf96de@gmail.com/
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AR8035 recently gained MDIX support. The same functions will work for
the AR8031/33 PHY. We just need to add the at803x_config_aneg()
callback.
This was tested on a Kontron sl28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
SmartEEE for the atheros phy was deemed buggy by Freescale and commits
were added to disable it for their boards.
In initial testing, SolidRun found that the default settings were
causing disconnects but by increasing the Tw buffer time we could allow
enough time for all parts of the link to come out of a low power state
and function properly without causing a disconnect. This allows us to
have functional power savings of between 300 and 400mW, rather than
disabling the feature altogether.
This commit adds support for disabling SmartEEE and configuring the Tw
parameters for 1G and 100M speeds.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This bit is enabled by default and advertises support for extended
next page support. XNP is only needed for 10GBase-T and MultiGig
support which is not supported. Additionally, Cisco MultiGig switches
will read this bit and attempt 10Gb negotiation even though Next Page
support is disabled. This will cause timeouts when the interface is
forced to 100Mbps and auto-negotiation will fail. The interfaces are
only 1000Base-T and supporting auto-negotiation for this only requires
the Next Page bit to be set.
Taken from:
7406c5244b
and adapted to mainline kernels by rmk.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1kzSdb-000417-FJ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert at803x_clk_out_config() to use phy_modify_mmd().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1kyc72-0008Pq-1x@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The only usage of vddio_regulator_ops and vddh_regulator_ops is to
assign their address to the ops field in the regulator_desc struct,
which is a const pointer. Make them const to allow the compiler to
put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add MDIX configuration ability for AR9331 and AR8035. Theoretically
it should work on other Atheros PHYs, but I was able to test only this
two.
Since I have no certified reference HW able to detect or configure MDIX, this
functionality was confirmed by oscilloscope.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
By placing the GENMASK value into an unsigned int and then passing it
to PREF_FIELD, the type is reduces down from ULL. Given the reduced
size of the type, the range checks in PREP_FAIL() are always true, and
-Wtype-limits then gives a warning.
By skipping the intermediate variable, the warning can be avoided.
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Atheros 100Base-T PHYs. The only difference seems to be
the ability to test 2 pairs instead of 4 and the lack of 1000Base-T
specific register.
Only the ATH9331 was tested with this patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ever since its first commit 0ca7111a38 ("phy: add AT803x driver") the
PHY ID mask was set to 0xffffffef. It is unclear to me why this mask was
chosen in the first place. Both the AR8031/AR8033 and the AR8035
datasheets mention it is always the given value:
- for AR8031/AR8033 its 0x004d/0xd074
- for AR8035 its 0x004d/0xd072
Unfortunately, I don't have a datasheet for the AR8030. Therefore, we
leave its PHY ID mask untouched. For the PHYs mentioned before use the
handy PHY_ID_MATCH_EXACT() macro.
I've tried to contact the author of the initial commit, but received no
answer so far.
Cc: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AR8031/AR8033 and the AR8035 support cable diagnostics. Adding
driver support is straightforward, so lets add it.
The PHY just do one pair at a time, so we have to start the test four
times. The cable_test_get_status() can block and therefore we can just
busy poll the test completion and continue with the next pair until we
are done.
The time delta counter seems to run at 125MHz which just gives us a
resolution of about 82.4cm per tick.
100m cable, A/B/C/D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: Open Circuit
Pair: Pair A, fault length: 107.94m
Pair: Pair B, result: Open Circuit
Pair: Pair B, fault length: 104.64m
Pair: Pair C, result: Open Circuit
Pair: Pair C, fault length: 105.47m
Pair: Pair D, result: Open Circuit
Pair: Pair D, fault length: 107.94m
1m cable, A/B connected, C shorted, D open:
Cable test started for device eth0.
Cable test completed for device eth0.
Pair: Pair A, result: OK
Pair: Pair B, result: OK
Pair: Pair C, result: Short within Pair
Pair: Pair C, fault length: 0.82m
Pair: Pair D, result: Open Circuit
Pair: Pair D, fault length: 0.82m
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AR8031 and AR8035 support the link speed downshift. Add driver
support for it. One peculiarity of these PHYs is that it needs a
software reset after changing the setting, thus add the .soft_reset()
op and do a phy_init_hw() if necessary.
This was tested on a custom board with the AR8031.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Qualcomm Atheros AR8032 Fast Ethernet PHY.
It shares many similarities with the already supported AR8030 PHY but
additionally supports MII connection to the MAC.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The masks in priv->clk_25m_reg and priv->clk_25m_mask are one-bits-set
for the values that comprise the fields, not zero-bits-set.
This patch fixes the clock frequency configuration for ATH8030 and
ATH8035 Atheros PHYs by removing the erroneous "~".
To reproduce this bug, configure the PHY with the device tree binding
"qca,clk-out-frequency" and remove the machine specific PHY fixups.
Fixes: 2f664823a4 ("net: phy: at803x: add device tree binding")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The probe() might enable a VDDIO regulator, which needs to be disabled
again before calling regulator_put(). Add a remove() function.
Fixes: 2f664823a4 ("net: phy: at803x: add device tree binding")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to its datasheet, the internal PHY doesn't have debug
registers nor MMDs. Since config_init() only configures delays and
clocks and so on in these registers it won't be needed on this PHY.
Remove it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix at least the displayed strings. The actual name of the chip is
AR803x.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AR8033 is the AR8031 without PTP support. All other registers are
the same. Unfortunately, they share the same PHY ID. Therefore, we
cannot distinguish between the one with PTP support and the one without.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring the CLK_25M pin as well as the RGMII I/O
voltage by the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the PHY-specific status register for the current operating mode
(speed and duplex) of the PHY. This register reflects the actual
mode that the PHY has resolved depending on either the advertisements
of autoneg is enabled, or the forced mode if autoneg is disabled.
This ensures that phylib's software state always tracks the hardware
state.
It seems both AR8033 (which uses the AR8031 ID) and AR8035 support
this status register. AR8030 is not known at the present time.
This patch depends on "net: phy: extract pause mode" and "net: phy:
extract link partner advertisement reading".
Reported-by: tinywrkb <tinywrkb@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: tinywrkb <tinywrkb@gmail.com>
Fixes: 5502b218e0 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct at803x_priv is never used in this driver. So remove it
and the probe function allocating it.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly this hardware can work with generic PHY driver, but this change
is needed to provided interrupt handling support.
Tested with dsa ar9331-switch driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supported PHY features are either auto-detected or explicitly set.
In both cases calling genphy_config_init isn't needed. All that
genphy_config_init does is removing features that are set as
supported but can't be auto-detected. Basically it duplicates the
code in genphy_read_abilities. Therefore remove such calls from
all PHY drivers.
v2:
- remove call also from new adin PHY driver
v3:
- pass NULL as config_init function pointer for dp83848
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver does a funny dance disabling and re-enabling
RX and/or TX delays. In any of the RGMII-ID modes, it first
disables the delays, just to re-enable them again right
away. This looks like a needless exercise.
Just enable the respective delays when in any of the
relevant 'id' modes, and disable them otherwise.
Also, remove comments which don't add anything that can't be
seen by looking at the code.
Signed-off-by: André Draszik <git@andred.net>
CC: Andrew Lunn <andrew@lunn.ch>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: Heiner Kallweit <hkallweit1@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This renames the GPIO reset of mdio devices from 'reset' to
'reset_gpio' to better differentiate between GPIO and
reset-controller driven reset line.
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently genphy_read_abilities() has been added that dynamically detects
clause 22 PHY abilities. I *think* this detection should work with all
supported PHY's, at least for the ones with basic features sets, i.e.
PHY_BASIC_FEATURES and PHY_GBIT_FEATURES. So let's remove setting these
features explicitly and rely on phylib feature detection.
I don't have access to most of these PHY's, therefore I'd appreciate
regression testing.
v2:
- make the feature constant a comment so that readers know which
features are supported by the respective PHY
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the Phy driver's link_change_notify callback is called
whenever the state machine is run (every second if polling), no matter
whether the state changed or not. This isn't needed and may confuse
users considering the name of the callback. Actually it contradicts
its kernel-doc description. Therefore let's change the behavior and
call this callback only in case of an actual state change.
This requires changes to the at803x and rockchip drivers.
at803x can be simplified so that it reacts on a state change to
PHY_NOLINK only.
The rockchip driver can also be much simplified. We simply re-init
the AFE/DSP registers whenever we change to PHY_RUNNING and speed
is 100Mbps. This causes very small overhead because we do this even
if the speed was 100Mbps already. But this is negligible and
I think justified by the much simpler code.
Changes are compile-tested only.
A little bit problematic seems to be to find somebody with the
hardware to test the changes to the two PHY drivers. See also [0].
David may be able to test the Rockchip driver.
[0] https://marc.info/?t=153782508800006&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per "Documentation/devicetree/bindings/net/ethernet.txt" RGMII mode
should not have delay in PHY whereas RGMII_ID and RGMII_RXID/RGMII_TXID
can have delay in PHY.
So disable the delay only for RGMII mode and enable for other modes.
Also treat the default case as disabled delays.
Fixes: cd28d1d6e52e: ("net: phy: at803x: Disable phy delay for RGMII mode")
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Peter Ujfalusi <peter.ujflausi@ti.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some helpers were declared with the "inline" function specifier.
It is preferable to let the compiler pick the right optimizations,
so drop the specifier for at803x_disable_rx_delay() and
at803x_disable_tx_delay()
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Peter Ujfalusi <peter.ujflausi@ti.com>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Libphy provides a standard set of helpers to access the MMD PHY
registers. Use those instead of relying on custom driver-specific
functions.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RGMII mode, phy delay should be disabled. Add this case along
with disable delay routines.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that flag PHY_HAS_INTERRUPT has been replaced with a check for
callbacks config_intr and ack_interrupt, we can remove setting this
flag from all driver configs.
Last but not least remove flag PHY_HAS_INTERRUPT completely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all new style LINK_MODE bits can be converted into old style
SUPPORTED bits. We need to warn when such a conversion is attempted.
Add a helper for this.
Convert all pr_warn() calls to phydev_warn() where possible.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith
Vladimir Oltean
Russell King
Jakub Kicinski
David Bauer
Michael Walle
Ioana Ciornei
Rikard Falkeborn
Oleksij Rempel
Andrew Lunn
David S. Miller
Heiner Kallweit
André Draszik
Vinod Koul
Carlo Caione