Since w83697hf_wdt/w83697ug_wdt watchdogs drivers were removed
in commit 7285fae934 ("watchdog: Remove drivers for W83697HF and W83697UG")
There are no need to keep their documentation
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The ixp2000 watchdog driver was removed in commit 065e823830 ("watchdog: remove ixp2000 driver")
No need to keep its documentation, so remove it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Since at32ap700x_wdt is gone, no need to keep its documentation
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Make refs to selftests files valid including:
- watchdog-test.c
- dnotify_test.c
Signed-off-by: Tom Saeger <tom.saeger@oracle.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This reverts commit 1fccb73011.
Reported as Bug 196509 - iTCO_wdt regression reboot before timeout expire
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a watchdog driver for Socionext UniPhier series SoC.
Note that the timeout value for this device must be a power
of 2 because of the specification.
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The ICH9 is listed as having TCO v2, and indeed the behavior in the
datasheet corresponds to v2 (for example the NO_REBOOT flag is
accessible via the 16KiB-aligned Root Complex Base Address).
However, the TCO counts twice just like in v1; the documentation
of the SECOND_TO_STS bit says: "ICH9 sets this bit to 1 to indicate
that the TIMEOUT bit had been (or is currently) set and a second
timeout occurred before the TCO_RLD register was written. If this
bit is set and the NO_REBOOT config bit is 0, then the ICH9 will
reboot the system after the second timeout. The same can be found
in the BayTrail (Atom E3800) datasheet, and even HOWTOs around
the Internet say that it will reboot after _twice_ the specified
heartbeat.
I did not find the Apollo Lake datasheet, but because v4/v5 has
a SECOND_TO_STS bit just like the previous version I'm enabling
this for Apollo Lake as well.
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Many watchdog drivers explicitly stop the watchdog when unregistering it.
While it is unclear if this is actually needed (the whatdog should not be
running at that time if it can be stopped), introduce a helper to
explicitly stop the watchdog in the watchdog core when unregistering it.
This helps reducing driver code size while retaining functionality.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the watchdog timer on PXI Embedded Controller.
Signed-off-by: Hui Chun Ong <hui.chun.ong@ni.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The previous patch renamed several files that are cross-referenced
along the Kernel documentation. Adjust the links to point to
the right places.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This update consists of:
- Fixes and improvements to existing tests
- Moving code from Documentation to selftests, samples, and tools.
Moves dnotify_test, prctl, ptp, vDSO, ia64, watchdog, and networking
tests from Documentation to selftests.
Moves mic/mpssd, misc-devices/mei, timers, watchdog, auxdisplay, and
blackfin examples from Documentation to samples.
Moves accounting, laptops/dslm, and pcmcia/crc32hash tools from
Documentation to tools.
Deletes BUILD_DOCSRC and its dependencies.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=60kH
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-4.9-rc1-update' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest updates from Shuah Khan:
"This update consists of:
- Fixes and improvements to existing tests
- Moving code from Documentation to selftests, samples, and tools:
* Moves dnotify_test, prctl, ptp, vDSO, ia64, watchdog, and
networking tests from Documentation to selftests.
* Moves mic/mpssd, misc-devices/mei, timers, watchdog, auxdisplay,
and blackfin examples from Documentation to samples.
* Moves accounting, laptops/dslm, and pcmcia/crc32hash tools from
Documentation to tools.
* Deletes BUILD_DOCSRC and its dependencies"
* tag 'linux-kselftest-4.9-rc1-update' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (21 commits)
selftests/futex: Check ANSI terminal color support
Doc: update 00-INDEX files to reflect the runnable code move
samples: move blackfin gptimers-example from Documentation
tools: move pcmcia crc32hash tool from Documentation
tools: move laptops dslm tool from Documentation
tools: move accounting tool from Documentation
samples: move auxdisplay example code from Documentation
samples: move watchdog example code from Documentation
samples: move timers example code from Documentation
samples: move misc-devices/mei example code from Documentation
samples: move mic/mpssd example code from Documentation
selftests: Move networking/timestamping from Documentation
selftests: move watchdog tests from Documentation/watchdog
selftests: move ia64 tests from Documentation/ia64
selftests: move vDSO tests from Documentation/vDSO
selftests: move ptp tests from Documentation/ptp
selftests: move prctl tests from Documentation/prctl
selftests: move dnotify_test from Documentation/filesystems
selftests/timers: Add missing error code assignment before test
selftests/zram: replace ZRAM_LZ4_COMPRESS
...
The change adds a simple watchdog pretimeout framework infrastructure,
its purpose is to allow users to select a desired handling of watchdog
pretimeout events, which may be generated by some watchdog devices.
A user selects a default watchdog pretimeout governor during
compilation stage.
Watchdogs with WDIOF_PRETIMEOUT capability now have one more device
attribute in sysfs, pretimeout_governor attribute is intended to display
the selected watchdog pretimeout governor.
The framework has no impact at runtime on watchdog devices with no
WDIOF_PRETIMEOUT capability set.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Since the watchdog framework centrializes the IOCTL interfaces of device
drivers now, SETPRETIMEOUT and GETPRETIMEOUT need to be added in the
common code.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[vzapolskiy: added conditional pretimeout sysfs attribute visibility]
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Move watchdog examples to samples and remove it from Documentation
Makefile. Create a new Makefile to build watchdog. It can be built
from top level directory or from watchdog directory:
Run make -C samples/watchdog or cd samples/watchdog; make
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Remove watchdog-test from Makefile to move the test to selftests.
Add Makefile and .gitignore for watchdog-test. watchdog-test will
not be run as part of selftests suite and will not be included in
install targets. It can be built separately for now.
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
A recent commit added a write to the watchdog test code for doing the "magic
close", but that caused a compile-time warning:
Documentation/watchdog/src/watchdog-test.c: In function ‘main’:
Documentation/watchdog/src/watchdog-test.c:94:5: warning: ignoring return value of ‘write’, declared with attribute warn_unused_result [-Wunused-result]
This changes the code to print a runtime warning if the write fails.
Fixes: 5a2d3de196 ("Documentation/watchdog: add support for magic close to watchdog-test")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Up to now, the watchdog status function called a driver function,
which was supposed to return the watchdog status. All but one
driver using the watchdog core did not implement this function,
and the driver implementing it did not implement it correctly
(the function is supposed to return WDIOF_ flags). At the same time,
at least some of the status information can be provided by the watchdog
core.
Provide the available status bits directly from the watchdog driver core.
Call the driver status function if it exists to get the boot status, but
always provide WDIOF_MAGICCLOSE and WDIOF_KEEPALIVEPING internally.
This patch makes the 'status' sysfs attribute always available.
This attribute is now displayed as hex number with 0x prepended to be
easier to decode.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Some drivers have the WDIOF_MAGICCLOSE set, which means that applications
need to write 'V' to the watchdog device before closing, otherwise the
driver won't stop the watchdog timer.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog-test utility outputs all messages to stderr, even those
that are not error messages. Output to stdout instead.
Instead of flushing the output after every write, just disabled
the output buffer.
Also display a dot for every ping of the watchdog, so that the user
knows that it's working.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The description of min_hw_heartbeat_ms is misleading and needs some
improvements.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WinSystems EBC-C384 watchdog timer driver supports two module
parameters: timeout and nowayout. These parameters should be documented
in the watchdog-parameters.txt file.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull watchdog updates from Wim Van Sebroeck:
- new drivers for: NI 903x/913x watchdog driver, WinSystems EBC-C384
watchdog timer and ARM SBSA watchdog driver
- Support for NCT6102D devices
- Improvements of the generic watchdog framework (improve restart
handler, make set_timeout optional, introduce infrastructure
triggered keepalives, ...
- improvements on the pnx4008 watchdog driver
- several smaller fixes and improvements
* git://www.linux-watchdog.org/linux-watchdog: (28 commits)
watchdog: Ensure that wdd is not dereferenced if NULL
watchdog: imx2: Convert to use infrastructure triggered keepalives
watchdog: dw_wdt: Convert to use watchdog infrastructure
watchdog: Add support for minimum time between heartbeats
watchdog: Make stop function optional
watchdog: Introduce WDOG_HW_RUNNING flag
watchdog: Introduce hardware maximum heartbeat in watchdog core
watchdog: Make set_timeout function optional
arm: lpc32xx: remove restart handler
arm: lpc32xx: phy3250 remove restart hook
watchdog: pnx4008: restart: support "cmd" from userspace
watchdog: pnx4008: add support for soft reset
watchdog: pnx4008: add restart handler
watchdog: pnx4008: update logging during power-on
watchdog: tangox_wdt: test clock rate to avoid division by 0
watchdog: atlas7_wdt: test clock rate to avoid division by 0
watchdog: s3c2410_wdt: Add max and min timeout values
Watchdog: introduce ARM SBSA watchdog driver
Documentation: add sbsa-gwdt driver documentation
watchdog: Add watchdog timer support for the WinSystems EBC-C384
...
Some watchdogs require a minimum time between heartbeats.
Examples are the watchdogs in DA9062 and AT91SAM9x.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Not all hardware watchdogs can be stopped. The driver for
such watchdogs would typically only set the WATCHDOG_HW_RUNNING
flag in its stop function. Make the stop function optional and set
WATCHDOG_HW_RUNNING in the watchdog core if it is not provided.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WDOG_HW_RUNNING flag is expected to be set by watchdog drivers if
the hardware watchdog is running. If the flag is set, the watchdog
subsystem will ping the watchdog even if the watchdog device is closed.
The watchdog driver stop function is now optional and may be omitted
if the watchdog can not be stopped. If stopping the watchdog is not
possible but the driver implements a stop function, it is responsible
to set the WDOG_HW_RUNNING flag in its stop function.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Introduce an optional hardware maximum heartbeat in the watchdog core.
The hardware maximum heartbeat can be lower than the maximum timeout.
Drivers can set the maximum hardware heartbeat value in the watchdog data
structure. If the configured timeout exceeds the maximum hardware heartbeat,
the watchdog core enables a timer function to assist sending keepalive
requests to the watchdog driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
For some watchdogs, the watchdog driver handles timeout changes without
explicitly setting any registers. In this situation, the watchdog driver
might only set the 'timeout' variable but do nothing else.
This can as well be handled by the infrastructure, so make the set_timeout
callback optional. If WDIOF_SETTIMEOUT is configured but the .set_timeout
callback is not available, update the timeout variable in the
infrastructure code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The sbsa-gwdt.txt documentation in devicetree/bindings/watchdog is for
introducing SBSA(Server Base System Architecture) Generic Watchdog
device node info into FDT.
Also add sbsa-gwdt introduction in watchdog-parameters.txt
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add support for the watchdog timer on NI cRIO-903x and cDAQ-913x real-
time controllers.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com>
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This driver adds sparc hypervisor watchdog support. The default
timeout is 60 seconds and the range is between 1 and
31536000 seconds. Both watchdog-resolution and
watchdog-max-timeout MD properties settings are supported.
Signed-off-by: Wim Coekaerts <wim.coekaerts@oracle.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lifetime of the watchdog device pointer is different from the lifetime
of its character device. Remove it entirely to avoid race conditions.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Zodiac watchdog driver attaches additional sysfs attributes to the
watchdog device. This has a number of problems: The watchdog device
lifetime differs from the driver lifetime, and the device structure
should therefore not be accessed from drivers. Also, creating sysfs
attributes after driver registration results in a potential race condition
if user space expects the attributes to exist but they don't exist yet.
Add support for creating driver specific sysfs attributes to the watchdog
core to solve the problems.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
All variables required by the watchdog core to manage a watchdog are
currently stored in struct watchdog_device. The lifetime of those
variables is determined by the watchdog driver. However, the lifetime
of variables used by the watchdog core differs from the lifetime of
struct watchdog_device. To remedy this situation, watchdog drivers
can implement ref and unref callbacks, to be used by the watchdog
core to lock struct watchdog_device in memory.
While this solves the immediate problem, it depends on watchdog drivers
to actually implement the ref/unref callbacks. This is error prone,
often not implemented in the first place, or not implemented correctly.
To solve the problem without requiring driver support, split the variables
in struct watchdog_device into two data structures - one for variables
associated with the watchdog driver, one for variables associated with
the watchdog core. With this approach, the watchdog core can keep track
of its variable lifetime and no longer depends on ref/unref callbacks
in the driver. As a side effect, some of the variables originally in
struct watchdog_driver are now private to the watchdog core and no longer
visible in watchdog drivers.
As a side effect of the changes made, an ioctl will now always fail
with -ENODEV after a watchdog device was unregistered with the character
device still open. Previously, it would only fail with -ENODEV in some
situations. Also, ioctl operations are now atomic from driver perspective.
With this change, it is now guaranteed that the driver will not unregister
a watchdog between a timeout change and the subsequent ping.
The 'ref' and 'unref' callbacks in struct watchdog_driver are no longer
used and marked as deprecated.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Many watchdog drivers register a reboot notifier in order to stop the
watchdog on system reboot. Thus we can factorize this code in the
watchdog core.
For that purpose, a new notifier block is added in watchdog_device for
internal use only, as well as a new watchdog_stop_on_reboot helper
function.
If this helper is called, watchdog core registers the related notifier
block and will stop the watchdog when SYS_HALT or SYS_DOWN is received.
Since this operation can be critical on some platforms, abort the device
registration if the reboot notifier registration fails.
Suggested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Many watchdog drivers implement the same code to register a restart
handler. This patch provides a generic way to set such a function.
The patch adds a new restart watchdog operation. If a restart priority
greater than 0 is needed, the driver can call
watchdog_set_restart_priority to set it.
Suggested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog test program is much more useful if it can configure the
timeout value and ping rate. This will allow you to test actual timeouts.
Adds the -t parameter to set the timeout value (in seconds), and -p to set
the ping rate (number of seconds between pings).
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a early_enable module parameter to the omap_wdt that starts the
watchdog on module insertion. The default value is 0 which does not
start the watchdog - which also does not change the behavior if the
parameter is not given.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Currently, watchdog subsystem require the misc subsystem to
register a watchdog. This may not be the case in case of an
early registration of a watchdog, which can be required when
the watchdog cannot be disabled.
This patch introduces a deferral mechanism to remove this requirement.
Signed-off-by: Jean-Baptiste Theou <jtheou@adeneo-embedded.us>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The omap_wdt kernel driver also understands the nowayout module
parameter. This updates the watchdog-parameters.txt to reflect this fact.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Change the Documentation makefiles from obj-m to subdir-y
to avoid generating unnecessary built-in.o files since nothing
in Documentation/ is ever linked in to vmlinux.
Signed-off-by: Peter Foley <pefoley2@pefoley.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch changes 'go of' to 'go off' and 'pretimout' to
'pretimeout'.
Signed-off-by: Sangjung Woo <sangjung.woo@samsung.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On some hardware platforms, the it87_wdt watchdog resets the machine
despite the watchdog daemon running and writing to /dev/watchdog.
This is due to Consumer IR buffer underrun interrupts being used as
triggers to reset the timer. On some buggy hardware implementations
such as the iEi AFL-12A-N270 single-board computer, this method does
not work.
However, resetting the timer by writing its original timeout value in
its configuration register over and over again suppresses the unwanted
reboots.
Add a module option (nocir), 0 by default in order not to break existing
setups. Setting it to 1 enables the workaround.
Fixes bug #42801 <https://bugzilla.kernel.org/show_bug.cgi?id=42801>.
Tested primarily on Linux 3.5.7, applies cleanly on Linux 3.13.5.
Signed-off-by: Marc van der Wal <x0r+kernel@x0r.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a driver for the hardware watchdogs in NVIDIA Tegra SoCs (Tegra30 and
later). This driver will configure one watchdog timer that will reset the
system in the case of a watchdog timeout.
This driver binds to the nvidia,tegra30-timer device node and gets its
register base from there.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Interrupt request doesn't use the right API: The TWD watchdog uses a per-cpu
interrupt (usually interrupt #30), and the GIC configuration should flag it as
such. With this setup, request_irq() should fail, and the right API is
request_percpu_irq(), together with enable_percpu_irq()/disable_percpu_irq().
Nothing ensures the userspace ioctl() will end-up kicking the watchdog on the
right CPU.
There are no users of this driver since a long time and it makes more sense to
get rid of it as nobody is looking to fix it.
In case somebody wakes up after this has been removed and needs it, please
revert this driver and pick these updates (These were never pushed to mainline):
http://comments.gmane.org/gmane.linux.ports.arm.kernel/245998
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add support for watchdog drivers to initialize/set the timeout field
of the watchdog_device structure. The timeout field is initialised
either with the module timeout parameter value (if valid) or with the
timeout-sec dt property (if valid). If both are invalid the initial
value is unchanged.
Signed-off-by: Fabio Porcedda <fabio.porcedda@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix compiler warning by making the function static:
Documentation/watchdog/src/watchdog-test.c:34:6: warning: no previous prototype for 'term'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This driver adds support for the watchdog functionality provided by
the Dialog Semiconductor DA9052 PMIC chip.
Tested on samsung smdkv6410 and i.mx53 QS boards.
Signed-off-by: Anthony Olech <Anthony.Olech@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If a driver's watchdog_device struct is part of a dynamically allocated
struct (which it often will be), merely locking the module is not enough,
even with a drivers module locked, the driver can be unbound from the device,
examples:
1) The root user can unbind it through sysfd
2) The i2c bus master driver being unloaded for an i2c watchdog
I will gladly admit that these are corner cases, but we still need to handle
them correctly.
The fix for this consists of 2 parts:
1) Add ref / unref operations, so that the driver can refcount the struct
holding the watchdog_device struct and delay freeing it until any
open filehandles referring to it are closed
2) Most driver operations will do IO on the device and the driver should not
do any IO on the device after it has been unbound. Rather then letting each
driver deal with this internally, it is better to ensure at the watchdog
core level that no operations (other then unref) will get called after
the driver has called watchdog_unregister_device(). This actually is the
bulk of this patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Corentin Labbe
Tom Saeger
Wim Van Sebroeck
Keiji Hayashibara
Paolo Bonzini
Guenter Roeck
Hui Chun Ong
Mauro Carvalho Chehab
Linus Torvalds
Vladimir Zapolskiy
Wolfram Sang
Shuah Khan
Arnd Bergmann
Timur Tabi
Brian Boylston
William Breathitt Gray
Nigel Croxon
Fu Wei
Kyle Roeschley
wim.coekaerts@oracle.com
Damien Riegel
Lars Poeschel
Jean-Baptiste Theou
Peter Foley
Sangjung Woo
Marc van der Wal
Andrew Chew
Viresh Kumar
Fabio Porcedda
Randy Dunlap
Ashish Jangam
Hans de Goede