Граф коммитов

1112 Коммитов

Автор SHA1 Сообщение Дата
Madhusudhan Chikkature cdeebaddb7 omap hsmmc: fix a bug in card remove scenario
The reset of data lines when the card is removed from the cage results in
a failure.The failure is seen if the card is removed from the cage when TC
is pending after a CMD with data received CC.The reset logic leaves the
controller in a state where niether a TC is received nor DTO.

The rest code can be safely removed here since it is taken care in the IRQ
handler.

Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-04-07 08:38:03 -07:00
Tejun Heo 5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Adrian Hunter 7198f3c9b1 mmc: fix incorrect interpretation of card type bits
In the extended CSD register the CARD_TYPE is an 8-bit value of which the
upper 6 bits were reserved in JEDEC specifications prior to version 4.4.
In version 4.4 two of the reserved bits were designated for identifying
support for the newly added High-Speed Dual Data Rate.  Unfortunately the
mmc_read_ext_csd() function required that the reserved bits be zero
instead of ignoring them as it should.

This patch makes mmc_read_ext_csd() ignore the CARD_TYPE bits that are
reserved or not yet supported.  It also stops the function jumping to the
end as though an error occurred, when it is only warns that the CARD_TYPE
bits (that it does interpret) are invalid.

Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-24 16:31:21 -07:00
Linus Torvalds 11bfe2ea73 Merge branch 'msm-mmc_sdcc' of git://codeaurora.org/quic/kernel/dwalker/linux-msm
* 'msm-mmc_sdcc' of git://codeaurora.org/quic/kernel/dwalker/linux-msm:
  msm_sdcc.c: missing brackets in msmsdcc_resume()
2010-03-12 16:21:24 -08:00
Linus Torvalds c32da02342 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
  doc: fix typo in comment explaining rb_tree usage
  Remove fs/ntfs/ChangeLog
  doc: fix console doc typo
  doc: cpuset: Update the cpuset flag file
  Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
  Remove drivers/parport/ChangeLog
  Remove drivers/char/ChangeLog
  doc: typo - Table 1-2 should refer to "status", not "statm"
  tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
  No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
  devres/irq: Fix devm_irq_match comment
  Remove reference to kthread_create_on_cpu
  tree-wide: Assorted spelling fixes
  tree-wide: fix 'lenght' typo in comments and code
  drm/kms: fix spelling in error message
  doc: capitalization and other minor fixes in pnp doc
  devres: typo fix s/dev/devm/
  Remove redundant trailing semicolons from macros
  fix typo "definetly" -> "definitely" in comment
  tree-wide: s/widht/width/g typo in comments
  ...

Fix trivial conflict in Documentation/laptops/00-INDEX
2010-03-12 16:04:50 -08:00
Vladimir Zapolskiy d759c3745e mxcmmc: fixed max_seg_size value on initialization
This unpleasant typo appeared while porting the driver from Freescale
original sources, where anyone can easily find the correct version.

Current incorrect version potentially can influence segment and merge
handling in block subsystem via MMC request queue settings.

Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-12 15:52:44 -08:00
Albert Herranz 516a824222 sdio: recognize io card without powercycle
SDIO Simplified Specification V2.00 states that it is strongly recommended
that the host executes either a power reset or issues a CMD52 (I/O Reset)
to re-initialize an I/O only card or the I/O portion of a combo card.
Additionally, the CMD52 must be issued first because it cannot be issued
after a CMD0.

With this patch the Nintendo Wii SDIO-based WLAN card is detected after a
system reset, without requiring a complete system powercycle.

Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-12 15:52:28 -08:00
Jiri Kosina 318ae2edc3 Merge branch 'for-next' into for-linus
Conflicts:
	Documentation/filesystems/proc.txt
	arch/arm/mach-u300/include/mach/debug-macro.S
	drivers/net/qlge/qlge_ethtool.c
	drivers/net/qlge/qlge_main.c
	drivers/net/typhoon.c
2010-03-08 16:55:37 +01:00
Magnus Damm 3d8ca8c0b9 mfd/mmc: SDHI Kconfig update
Enable the sh_mobile_sdhi mfd driver on SH-Mobile ARM
processors. While at it, make CONFIG_TMIO_MMC depend on
CONFIG_MFD_SH_MOBILE_SDHI.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07 22:17:32 +01:00
Magnus Damm 7ee422dc6e tmio_mmc: Balance cell enable()/disable() calls
This patch adds cell->disable() calls to the tmio-mmc
probe() error handling and the remove() function.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07 22:17:27 +01:00
Magnus Damm 6d9af5af61 tmio_mmc: Use 100ms mmc_detect_change() delay
This patch changes the tmio_mmc driver to wait 100ms
before checking the card detect status. This type of
delay is quite common among mmc drivers, it seems that
most hardware platforms need to give the hardware some
time to settle before checking card availabilty.

Hotplug is half-broken without this patch on the sh7724
Ecovec board. Hot insertion seems ok but eject is never
detected without this patch.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07 22:17:26 +01:00
Yusuke Goda b741d440a9 tmio_mmc: Add MMC_CAP_MMC_HIGHSPEED support V2
Enable MMC_CAP_XX support in the tmio_mmc driver if
pdata->capabilities is set.

Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07 22:17:26 +01:00
Guennadi Liakhovetski a8c39d8deb tmio_mmc: Keep card-detect interrupts enabled
On SuperH platforms the SDHI controller does not produce any command IRQs after
a completed IO. This leads to card-detect interrupts staying disabled. Do not
disable card-detect interrupts on DATA IRQs.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2010-03-07 22:17:25 +01:00
Vasily Khoruzhick 8493829489 mmc: enable DMA on Ricoh sdhci reader by default
This card reader doesn't advertise, however DMA works well.  Probably
windows SDHCI driver assumes that all readers support DMA and thus we see
that bug.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Norbert Preining <preining@logic.at>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:43 -08:00
Nicolas Ferre 752993ef8e mmc: at91_mci: correct kunmap_atomic()
kunmap_atomic() accepts a pointer to any location in the page so we do not
need the subtraction and cast.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:43 -08:00
Nicolas Ferre 5b27a1a566 mmc: at91_mci: introduce per-mci-revision conditional code
We used to manage features and differences on a per-cpu basis.  As several
cpus share the same mci revision, this patch aggregates cpus that have the
same IP revision in one defined constant.  We use the
at91mci_is_mci1rev2xx() funtion name not to mess with newer Atmel sd/mmc
IP called "MCI2".  _rev2 naming could have been confusing...

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:43 -08:00
Nicolas Ferre 541e7ef039 mmc: at91_mci: Enable MMC_CAP_SDIO_IRQ only when it actually works.
According to the datasheets AT91SAM9261 does not support SDIO interrupts,
and AT91SAM9260/9263 have an erratum requiring 4bit mode while using slot
B for the interrupt to work.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:43 -08:00
Wolfgang Muees 9af13be2ac mmc: at91_mci: enable large data blocks
This patch is setting some max_ variables for the IO elevator, so the
elevator will put requests for large data blocks to the driver.  This is
critical for

a) speed

and

b) wear leveling of the flash chip controller: Otherwise the controller
   will treat the SD card badly with millions of single 4 KByte write
   commands.  This will lead to a shorter life time for the SD cards.

Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:43 -08:00
Wolfgang Muees 86ee26f5b0 mmc: at91_mci: use DMA buffer for read
Convert the read to use the DMA buffer as well.  The old code was doing
double-buffering DMA with the PDC; no way to make it work.  Replace it
with a single-PDC approach.  It also simplify things removing the need for
a pre_dma_read() function.

[nicolas.ferre@atmel.com coding style modifications]
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:43 -08:00
Wolfgang Muees 3780d90602 mmc: at91_mci: use one coherent DMA buffer
The TX DMA buffer is allocated only once, because the
allocation/deallocation of the buffer for EACH chunk of data is
time-consuming and prone to memory fragmentation.

Using a coherent DMA buffer avoids extra data cache calls.

[nicolas.ferre@atmel.com: coding style modifications]
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:41 -08:00
Wolfgang Muees a04ac5b9b4 mmc: at91_mci: fix timeout errors
Fix two timeout errors, one for slow SDHC cards and one for slow users
while inserting SD cards.

Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:39 -08:00
Wolfgang Muees 0b3520f2df mmc: at91_mci: fix pointer errors
Fixes two pointer errors, one which leads to memory overwrites if used
with large chunks of data.

Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <avictor.za@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:37 -08:00
Lars-Peter Clausen dc2ed55280 s3cmci: s3cmci_card_present: Use no_detect to decide whether there is a card detect pin
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:37 -08:00
Lars-Peter Clausen c212808a1b s3cmci: initialize default platform data no_wprotect and no_detect with 1
If no platform_data was givin to the device it's going to use it's default
platform data struct which has all fields initialized to zero.  As a
result the driver is going to try to request gpio0 both as write protect
and card detect pin.  Which of course will fail and makes the driver
unusable

Previously to the introduction of no_wprotect and no_detect the behavior
was to assume that if no platform data was given there is no write protect
or card detect pin.  This patch restores that behavior.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:37 -08:00
Daniel Drake 6b5eda369a sdio: put active devices into 1-bit mode during suspend
And bring them back to 4-bit mode during resume.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:37 -08:00
Nicolas Pitre 40216842dc sdio: kick the interrupt thread upon a resume
Some SDIO cards may suspend while keeping function interrupts active
especially in the powered suspend case.  Upon resume we need to kick the
SDIO interrupt thread to check for pending interrupts and to restart card
IRQ detection at the host controller level.

Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:37 -08:00
Chris Ball 3bca4cf703 sdio: don't use CMD[357] as part of a powered SDIO resume
Seen on a Marvell 8686 SDIO card and Via VX855 controller: we must avoid
sending CMD3/5/7 on a resume where power has been maintained, because the
8686 will refuse to respond to them and the MMC stack will give up on the
card.

Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:37 -08:00
Nicolas Pitre 2f4cbb3d83 sdio: sdhci support for suspend mode PM features
Tested with an XO v1.5 from OLPC.

Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:37 -08:00
Nicolas Pitre da68c4eb25 sdio: introduce API for special power management features
This patch series provides the core changes needed to allow SDIO cards to
remain powered and active while the host system is suspended, and let them
wake up the host system when needed.  This is used to implement
wake-on-lan with SDIO wireless cards at the moment.  Patches to add that
support to the libertas driver will be posted separately.

This patch:

Some SDIO cards have the ability to keep on running autonomously when the
host system is suspended, and wake it up when needed.  This however
requires that the host controller preserve power to the card, and
configure itself appropriately for wake-up.

There is however 4 layers of abstractions involved: the host controller
driver, the MMC core code, the SDIO card management code, and the actual
SDIO function driver.  To make things simple and manageable, host drivers
must advertise their PM capabilities with a feature bitmask, then function
drivers can query and set those features from their suspend method.  Then
each layer in the suspend call chain is expected to act upon those bits
accordingly.

[akpm@linux-foundation.org: fix typo in comment]
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:36 -08:00
Ben Dooks 9e506f35b1 sdhci: improve sdhci sdhci_set_adma_desc() code
sdhci_set_adma_desc() is using byte-writes to write data in a specified
order into memory.  Change to using __le16 for the two byte and __le32 for
the four byte cases and use the cpu_to_{le16,le32} to do the conversion
before writing.

This will reduce the size of the code and the number of writes as we no
longer need to chop the data up before writing.

As an example on ARM S3C64XX SoC, in little-endian configuration:

 000000d4 <sdhci_set_adma_desc>:
-      d8:	e1a0c423 	lsr	ip, r3, #8
-      dc:	e1a0ec21 	lsr	lr, r1, #24
-      e0:	e1a04821 	lsr	r4, r1, #16
-      e4:	e1a05421 	lsr	r5, r1, #8
-      e8:	e1a06442 	asr	r6, r2, #8
-      ec:	e5c0c001 	strb	ip, [r0, #1]
-      f0:	e5c0e007 	strb	lr, [r0, #7]
-      f4:	e5c04006 	strb	r4, [r0, #6]
-      f8:	e5c05005 	strb	r5, [r0, #5]
-      fc:	e5c01004 	strb	r1, [r0, #4]
-     100:	e5c06003 	strb	r6, [r0, #3]
-     104:	e5c02002 	strb	r2, [r0, #2]
-     108:	e5c03000 	strb	r3, [r0]
+      d4:	e5801004 	str	r1, [r0, #4]
+      d8:	e1c030b0 	strh	r3, [r0]
+      dc:	e1c020b2 	strh	r2, [r0, #2]

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:36 -08:00
Ben Dooks 118cd17d41 sdhci: add adma descriptor set call
The code to write the ADMA descriptor into memory is repeated several
times throughout sdhci_adma_table_pre, and thus should be moved into a
common function.  This will also be useful if the patch to make the write
more efficient is accepted.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:36 -08:00
Bing Zhao 3fb7fb4a01 sdio: add quirk to clamp byte mode transfer
Some SDIO cards expect byte transfers not to exceed the configured block
transfer size.  Add a quirk to that effect.

Patches to make use of this quirk will be sent separately.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:36 -08:00
Cliff Cai 729adf1b5f mmc: bfin_sdh: set timeout based on actual card data
The hardcoded value doesn't really work for all cards.

Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:36 -08:00
Mike Frysinger 05dabcc4a5 mmc: bfin_sdh: drop redundant MMC depend string
The host/Kconfig file is only included when MMC is selected.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:36 -08:00
Mike Frysinger c744d98872 mmc: bfin_sdh: fix unused sg warning on BF51x/BF52x systems
The local sg variable is only used with BF54x code.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:36 -08:00
Nicolas Ferre 09591dd318 mmc: Atmel host kconfig cleanup for everyone else
This prevents those without an Atmel chip having a line in kernel
configuration which says "Atmel SD/MMC Driver" without any option.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:36 -08:00
Vipin Bhandari 132f10746c davinci: MMC: add support for 8bit MMC cards
Add support for 8bit MMC cards.  The controller data width is configurable
depending on the wires setting in the platform data structure.

MMC 8bit is tested on OMAPL137 and MMC 4bit is tested on OMAPL138 EVM.

Signed-off-by: Vipin Bhandari <vipin.bhandari@ti.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:36 -08:00
Maxim Levitsky 03cd8f7ebe ricoh_mmc: port from driver to pci quirk
This patch solves nasty problem original driver has.

Original goal of the ricoh_mmc was to disable this device because then,
mmc cards can be read using standard SDHCI controller, thus avoiding
writing of yet another driver.

However, the act of disablement, makes other pci functions that belong to
this controller (xD and memstick) shift up one level, thus pci core has
now wrong idea about these devices.

To fix this issue, this patch moves the driver into the pci quirk section,
thus it is executes before the pci is enumerated, and therefore solving
that issue, also same sequence of commands is performed on resume for same
reasons.

Also regardless of the above, this way is cleaner.  You still need to set
CONFIG_MMC_RICOH_MMC to enable this quirk

Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Philip Langdale <philipl@overt.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:36 -08:00
Linus Torvalds 9446808022 Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (36 commits)
  jsm: fixing error if the driver fails to load
  jsm: removing the uart structure and filename on error
  tty: Add a new VT mode which is like VT_PROCESS but doesn't require a VT_RELDISP ioctl call
  tty: Keep the default buffering to sub-page units
  tty: Fix up char drivers request_room usage
  tty: Fix the ldisc hangup race
  serial: timberdale: Remove dependancies
  nozomi: Tidy up the PCI table
  nozomi: Fix mutex handling
  nozomi: Add tty_port usage
  sdio_uart: Use kfifo instead of the messy circ stuff
  serial: bcm63xx_uart: allow more than one uart to be registered.
  serial: bcm63xx_uart: don't use kfree() on non kmalloced area.
  serial: bfin_5xx: pull in linux/io.h for ioremap prototypes
  serial: bfin_5xx: kgdboc should accept gdb break only when it is active
  serial: bfin_5xx: need to disable DMA TX interrupt too
  serial: bfin_5xx: remove useless gpio handling with hard flow control
  Char: synclink, remove unnecessary checks
  tty: declare MODULE_FIRMWARE in various drivers
  ip2: Add module parameter.
  ...
2010-03-03 08:47:22 -08:00
Alan Cox 8b197a5ce7 sdio_uart: Use kfifo instead of the messy circ stuff
Revised patch to use the new kfifo API. This replaces the one that was dropped
from -next due to collisions with the kfifo API changes.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:20 -08:00
Tony Lindgren d702d12167 Merge with mainline to remove plat-omap/Kconfig conflict
Conflicts:
	arch/arm/plat-omap/Kconfig
2010-03-01 14:19:05 -08:00
Linus Torvalds ac0f6f927d Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (100 commits)
  ARM: Eliminate decompressor -Dstatic= PIC hack
  ARM: 5958/1: ARM: U300: fix inverted clk round rate
  ARM: 5956/1: misplaced parentheses
  ARM: 5955/1: ep93xx: move timer defines into core.c and document
  ARM: 5954/1: ep93xx: move gpio interrupt support to gpio.c
  ARM: 5953/1: ep93xx: fix broken build of clock.c
  ARM: 5952/1: ARM: MM: Add ARM_L1_CACHE_SHIFT_6 for handle inside each ARCH Kconfig
  ARM: 5949/1: NUC900 add gpio virtual memory map
  ARM: 5948/1: Enable timer0 to time4 clock support for nuc910
  ARM: 5940/2: ARM: MMCI: remove custom DBG macro and printk
  ARM: make_coherent(): fix problems with highpte, part 2
  MM: Pass a PTE pointer to update_mmu_cache() rather than the PTE itself
  ARM: 5945/1: ep93xx: include correct irq.h in core.c
  ARM: 5933/1: amba-pl011: support hardware flow control
  ARM: 5930/1: Add PKMAP area description to memory.txt.
  ARM: 5929/1: Add checks to detect overlap of memory regions.
  ARM: 5928/1: Change type of VMALLOC_END to unsigned long.
  ARM: 5927/1: Make delimiters of DMA area globally visibly.
  ARM: 5926/1: Add "Virtual kernel memory..." printout.
  ARM: 5920/1: OMAP4: Enable L2 Cache
  ...

Fix up trivial conflict in arch/arm/mach-mx25/clock.c
2010-03-01 09:15:15 -08:00
Linus Torvalds b1bf936840 Merge branch 'for-2.6.34' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.34' of git://git.kernel.dk/linux-2.6-block: (38 commits)
  block: don't access jiffies when initialising io_context
  cfq: remove 8 bytes of padding from cfq_rb_root on 64 bit builds
  block: fix for "Consolidate phys_segment and hw_segment limits"
  cfq-iosched: quantum check tweak
  blktrace: perform cleanup after setup error
  blkdev: fix merge_bvec_fn return value checks
  cfq-iosched: requests "in flight" vs "in driver" clarification
  cciss: Fix problem with scatter gather elements in the scsi half of the driver
  cciss: eliminate unnecessary pointer use in cciss scsi code
  cciss: do not use void pointer for scsi hba data
  cciss: factor out scatter gather chain block mapping code
  cciss: fix scatter gather chain block dma direction kludge
  cciss: simplify scatter gather code
  cciss: factor out scatter gather chain block allocation and freeing
  cciss: detect bad alignment of scsi commands at build time
  cciss: clarify command list padding calculation
  cfq-iosched: rethink seeky detection for SSDs
  cfq-iosched: rework seeky detection
  block: remove padding from io_context on 64bit builds
  block: Consolidate phys_segment and hw_segment limits
  ...
2010-03-01 09:00:29 -08:00
Manuel Lauss 3b839070f1 MMC: AU1xMMC: Allow platforms to disable host capabilities
Although the hardware supports a 4/8bit SD interface and the driver
unconditionally advertises all hardware caps to the MMC core, not all
datalines may actually be wired up.  This patch introduces another
field to au1xmmc platform data allowing platforms to disable certain
advanced host controller features.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: linux-mmc@vger.kernel.org
CC: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/460/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2010-02-27 12:53:19 +01:00
Manuel Lauss 963accbc82 MIPS: Alchemy: change dbdma to accept physical memory addresses
DMA can only be done from physical addresses; move the "virt_to_phys"
source/destination buffer address translation from the dbdma queueing
functions (since the hardware can only DMA to/from physical addresses)
to their respective users.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2010-02-27 12:52:55 +01:00
Manuel Lauss ea071cc705 MIPS: Alchemy: remove dbdma compat macros
Remove dbdma compat macros, move remaining users over to default
queueing functions and -flags.

(Queueing function signature has changed in order to give
 a build failure instead of silent functional changes due
 to the no longer implicitly specified DDMA_FLAGS_IE flag)

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2010-02-27 12:52:54 +01:00
Martin K. Petersen 8a78362c4e block: Consolidate phys_segment and hw_segment limits
Except for SCSI no device drivers distinguish between physical and
hardware segment limits.  Consolidate the two into a single segment
limit.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2010-02-26 13:58:08 +01:00
Martin K. Petersen 086fa5ff08 block: Rename blk_queue_max_sectors to blk_queue_max_hw_sectors
The block layer calling convention is blk_queue_<limit name>.
blk_queue_max_sectors predates this practice, leading to some confusion.
Rename the function to appropriately reflect that its intended use is to
set max_hw_sectors.

Also introduce a temporary wrapper for backwards compability.  This can
be removed after the merge window is closed.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2010-02-26 13:58:08 +01:00
Russell King 3560adf620 Merge branches 'at91', 'cache', 'cup', 'ep93xx', 'ixp4xx', 'nuc', 'pending-dma-streaming', 'u300' and 'umc' into devel 2010-02-25 22:06:43 +00:00
Linus Walleij 64de028948 ARM: 5940/2: ARM: MMCI: remove custom DBG macro and printk
This removes the custom DBG macro in favor of the in-kernel
dev_dbg() macro. Probably a leftover from a time when dev_dbg()
didn't yet exist. Also remove a printk() in favor of dev_err().

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-02-21 22:21:17 +00:00