Граф коммитов

13 Коммитов

Автор SHA1 Сообщение Дата
Andrew Lunn 3a31f2d7fc ARM: DT: Kirkwood: Use symbolic names from gpio.h
Use GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW instead of 0 and 1.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2013-12-08 01:00:54 +00:00
Andrew Lunn 23301190d2 ARM: DT: Kirkwood: Use symbolic names from input.h
Replace the numeric key value with a symbolic name from
<bt-bindings/input/input.h>

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2013-12-08 01:00:53 +00:00
Jason Gunthorpe 7f69f8a499 ARM: kirkwood: Remove kirkwood_setup_wins and rely on the DT binding
kirkwood_setup_wins is the last manual caller of mbus in kirkwood, don't
call it for DT boards and rely on the DT having a mbus node with
a proper ranges property to setup these windows.

Move all the mbus ranges properties for all boards into kirkwood.dtsi,
since they are currently all the same.

This makes the DT self consistent, since the physical address of the
NAND and CRYPTO are both referenced internally. The arbitary Linux
constants KIRKWOOD_NAND_MEM_PHYS_BASE and KIRKWOOD_SRAM_PHYS_BASE
no longer have to match the DT values.

Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2013-10-01 16:28:03 +00:00
Linus Torvalds 44598f98b9 ARM: SoC board updates for 3.12
Board updates for 3.12. Again, a bit of domain overlap with SoC and DT branches,
 but most of this is around legacy code and board support. We've found that
 platform maintainers have a hard time separating all of these out and might
 move towards fewer branches for next release.
 
 - Removal of a number of Marvell Kirkwood board files, since contents
   is now common and mostly configured via DT.
 - Device-tree updates for Marvell Dove, including irqchip and clocksource
   setup.
 - Defconfig updates. Gotta go somewhere. One new one for Renesas Lager.
 - New backlight drivers for backlights used on Renesas shmobile platforms.
 - Removal of Renesas leds driver.
 - Shuffling of some of the new Broadcom platforms to give room for others in
   the same mach directory. More in 2.13.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJSKhrfAAoJEIwa5zzehBx3OOAQAJCWhoYaHvWmyAf+xCOQNpX2
 YgAngENW04VpHFOyn6BtoGv6+5JypdB2TmK3GHHlVJd1Im5mD1wgm8hAfgyV8lQ4
 UeJULdA2HZAstKeTirO65BIyUb5QIrWakF24ccfIfg2xeScM8FV0m8cmzeo3fYAf
 DmmeoSCmvTdu/cDWBNlsQZ/as8qCQwyF+5kZg+SMl1btA1Publu2I5lDE02TH46d
 sc5mN+ihw0JG62EJV7pov6uVyeFLExoTbrNfQZ4rixmKkMDS/jq5ZbBS5c0i8ULF
 s1UMSZtYTcUO9rAPv3+MOIc7fq7nKo9lLuwMrA1HHUEDJ2BEi8DIp99F+ZYm/MSL
 WpVxYNwOobPcMJBYGR2fy4GgpIyWB285GgrBUxcq7t0Xi4uBbptwjLhDE4d7LREV
 8guW251R+OEVPYcwFctsubnox0MViyC3CQ1FaAAdtTjpSKomlhk/yaxaQ9nGrxls
 QCZgXHWm4Ir3QYv8XfOn0X9vdP81EnX11SiwtrRSJ71QMs814nB8NdPDqU4VHsw8
 exKmqjq/Lt+F9Kpxn/FevNNuYOdefZNQi00yl3ERchdIGdvRwE/0yA0D69mpwIVr
 E41UwvH3g43vazCo2PMdWPWuFlpGMR3iZ4pXnDLH/w33ppfJWfokYwKSRQ/mu/MN
 LMjkwoZn1X+fZzNSh9/G
 =EGua
 -----END PGP SIGNATURE-----

Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC board updates from Olof Johansson:
 "Board updates for 3.12.  Again, a bit of domain overlap with SoC and
  DT branches, but most of this is around legacy code and board support.
  We've found that platform maintainers have a hard time separating all
  of these out and might move towards fewer branches for next release.

   - Removal of a number of Marvell Kirkwood board files, since contents
     is now common and mostly configured via DT.
   - Device-tree updates for Marvell Dove, including irqchip and
     clocksource setup.
   - Defconfig updates.  Gotta go somewhere.  One new one for Renesas
     Lager.
   - New backlight drivers for backlights used on Renesas shmobile
     platforms.
   - Removal of Renesas leds driver.
   - Shuffling of some of the new Broadcom platforms to give room for
     others in the same mach directory.  More in 3.13"

* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
  mmc: sdhci-bcm-kona: Staticize sdhci_bcm_kona_card_event
  mmc: sdhci-bcm-kona: Remove unneeded version.h inclusion
  ARM: bcm: Make secure API call optional
  ARM: DT: binding fixup to align with vendor-prefixes.txt (drivers)
  ARM: mmc: fix NONREMOVABLE test in sdhci-bcm-kona
  ARM: bcm: Rename board_bcm
  mmc: sdhci-bcm-kona: make linker-section warning go away
  ARM: tegra: defconfig updates
  ARM: dove: add initial DT file for Globalscale D2Plug
  ARM: dove: add GPIO IR receiver node to SolidRun CuBox
  ARM: dove: add common pinmux functions to DT
  ARM: dove: add cpu device tree node
  ARM: dove: update dove_defconfig with SI5351, PCI, and xHCI
  arch/arm/mach-kirkwood: Avoid using ARRAY_AND_SIZE(e) as a function argument
  ARM: kirkwood: fix DT building and update defconfig
  ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform code
  ARM: configs: disable DEBUG_LL in bcm_defconfig
  ARM: bcm281xx: Board specific reboot code
  ARM bcm281xx: Turn on socket & network support.
  ARM: bcm281xx: Turn on L2 cache.
  ...
2013-09-06 13:34:43 -07:00
Ezequiel Garcia 54397d8534 ARM: kirkwood: Relocate PCIe device tree nodes
Now that mbus has been added to the device tree, it's possible to
move the PCIe nodes out of the ocp node, placing it directly
below the mbus. This is a more accurate representation of the hardware.

Moving the PCIe nodes, we now need to introduce an extra cell to
encode the window target ID and attribute. Since this depends on
the PCIe port, we split the ranges translation entries, to
correspond to each MBus window.

In addition, we encode the PCIe memory and I/O apertures in the MBus
node, according to the MBus DT binding specification. The choice made
is 0xe0000000-0xf0000000 for memory space, and 0xf200000-0xf2100000 for
I/O space. These apertures can be changed in each per-board DT file.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2013-08-06 14:11:53 +00:00
Ezequiel Garcia 0ab6129c56 ARM: kirkwood: Use the preprocessor on device tree files
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2013-08-06 14:11:37 +00:00
Sebastian Hesselbarth 876e233335 ARM: kirkwood: add gigabit ethernet and mvmdio device tree nodes
This patch adds mv643xx_eth and mvmdio device tree nodes for DT enabled
Kirkwood boards. Phy nodes are also added with reg property set on a
per-board basis.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2013-07-25 20:54:04 +00:00
Linus Torvalds ee1a8d402e ARM SoC device tree changes
These changes from 30 individual branches for the most part update device
 tree files, but there are also a few source code changes that have crept
 in this time, usually in order to atomically move over a driver from
 using hardcoded data to DT probing.
 
 A number of platforms change their DT files to use the C preprocessor,
 which is causing a bit of churn, but that is hopefully only this once.
 
 There are a few conflicts with the other branches unfortunately:
 
 * in exynos5440.dtsi and kirkwood-6281.dtsi, device nodes are added
   from multiple branches. Need to be careful to have the right
   set of closing braces as git gets this one wrong.
 
 * In kirkwood.dtsi, one 'ranges' line got split into two lines, while
   another line got added. Order of the lines does not matter.
 
 * in sama5d3.dtsi, some cleanup was merged the wrong way, causing
   a bogus conflict. We want the 'dmas' and 'dma-names' properties
   to get added here.
 
 * Two lines got removed independently in arch/arm/mach-mxs/mach-mxs.c
 
 * Contents get added independently in arch/arm/mach-omap2/cclock33xx_data.c
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIVAwUAUdLnpGCrR//JCVInAQI50RAAsXbH1SGvjKJemXhRkFloPDYpCbgdDUFr
 ChUbjNV1xsY/jaNCfMa5/Qo7lgz/Ot7BpJef9fZn7ret+dc7nchqe/4iIkAokAUh
 E4ao9D1dP5aAA0ihdbSQHCZtR/0SUR81h6BoOVuo/1mvEiBaFbWAeYe8/6LJd9II
 OU1w9bDmjfZWYFUXs+j2VF76ueZQ+kz69XDKZUGtkqN76m1AL8lGDurj5jxvyllF
 VJns8d9q2nr2q9PferfajK6rkOIPaTpwKblxZHUgobCyOitZaiZM0NgF733TsNM6
 HXmhDhkcn7T81+SiHVfigJ/nxo9UgU4zNJCODF3WZIwGIj3FbxvCOpdCYi2NhCO8
 oLcgDk57tpoKpB3gvAmYVQHP9FIepFa/WAWyPIADA7PkpYrwgc4v+cLEHXpd8SRv
 viLLIa5QuNdMeaK+Md9OKmKZFd7uFD9jiMtmdm6IpEVDDjMgoteb2XSoEtNebmtY
 MfbW4okn118a2dFKKaPTKcXVW/a5FRp2JGfB0A58RQHaJWj3JsY1bFn/xWPEpTOA
 IWB/HHMln0LYTL2AXN9HcaL1jnGI1Wq5eWBurX+cXQ/ij1A6jfoRKYglx7AQqOHj
 iWcGYtKLLJCgiWFnLSwcljZhfoYr0/z7rhns6yo7/vhN0riy+M84OgN4HbAmUzc1
 Bgy9PnJTNo8=
 =8PtJ
 -----END PGP SIGNATURE-----

Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC device tree changes from Arnd Bergmann:
 "These changes from 30 individual branches for the most part update
  device tree files, but there are also a few source code changes that
  have crept in this time, usually in order to atomically move over a
  driver from using hardcoded data to DT probing.

  A number of platforms change their DT files to use the C preprocessor,
  which is causing a bit of churn, but that is hopefully only this once"

* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (372 commits)
  ARM: at91: dt: rm9200ek: add spi support
  ARM: at91: dt: rm9200: add spi support
  ARM: at91/DT: at91sam9n12: add SPI DMA client infos
  ARM: at91/DT: sama5d3: add SPI DMA client infos
  ARM: at91/DT: fix SPI compatibility string
  ARM: Kirkwood: Fix the internal register ranges translation
  ARM: dts: bcm281xx: change comment to C89 style
  ARM: mmc: bcm281xx SDHCI driver (dt mods)
  ARM: nomadik: add the new clocks to the device tree
  clk: nomadik: implement the Nomadik clocks properly
  ARM: dts: omap5-uevm: Provide USB Host PHY clock frequency
  ARM: dts: omap4-panda: Fix DVI EDID reads
  ARM: dts: omap4-panda: Add USB Host support
  arm: mvebu: enable mini-PCIe connectors on Armada 370 RD
  ARM: shmobile: irqpin: add a DT property to enable masking on parent
  ARM: dts: AM43x EPOS EVM support
  ARM: dts: OMAP5: Add bandgap DT entry
  ARM: dts: AM33XX: Add pinmux configuration for CPSW to am335x EVM
  ARM: dts: AM33XX: Add pinmux configuration for CPSW to EVMsk
  ARM: dts: AM33XX: Add pinmux configuration for CPSW to beaglebone
  ...
2013-07-02 14:23:01 -07:00
Andrew Lunn 918f8f3096 ARM: Kirkwood: ts219: Enable second PCIe port in DT.
Enable the second PCIe port on QNAP TS-11x/TS-21x devices as newer
revisions (rev 1.3) have a USB 3.0 chip from Etron on PCIe port 1.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2013-06-11 16:02:08 +00:00
Thomas Petazzoni 259e234608 arm: kirkwood: convert QNAP TS219 to use DT for the PCIe interface
Now that the PCIe mvebu driver is usable on Kirkwood, use it instead
of the legacy PCIe code, since it allows to describe the PCIe
interfaces in the Device Tree.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2013-05-27 16:02:12 +00:00
Thomas Petazzoni a4936cfa5d arm: kirkwood: ts219: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.

Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.

This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:

pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-By: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2013-05-27 15:34:23 +00:00
Andrew Lunn 1f6e46bf6e ARM: Kirkwood: Convert TS219 to pinctrl.
Make use of the pinctrl driver for configuring all the pins, instead
of using the Orion mpp code.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2012-11-24 02:57:43 +00:00
Andrew Lunn 9eb61f4736 ARM: Kirkwood: Add basic device tree support for QNAP TS219.
The two different variants of QNAP TS devices, varying by SoC, put the
GPIO keys on different GPIO lines. Hence we need two different DT
board descriptions, which share the same board-ts219.c file.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
2012-07-27 16:48:52 +02:00