Граф коммитов

460 Коммитов

Автор SHA1 Сообщение Дата
Vikas Chaudhary 65a17da82a [SCSI] qla4xxx: Update driver version to 5.03.00-k1
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:49:47 +04:00
Tej Parkash 546fef27c3 [SCSI] qla4xxx: Disable generating pause frames for ISP83XX
In case of FW hung ISP83XX generates continuous pause frames
which causes switch to disable port.
Added fix to disable generating pause frames in case of
FW hung

Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:49:00 +04:00
Manish Dusane 48a859d29f [SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX
Issue:
For ISP83XX risc_intr getting clear two times in case of polling mode.
risc_intr getting clear from interrupt_service_routine() as well
from process_mbox_intr() because of this driver may clear risc_intr
without processing interrupt.

Fix:
Do not clear risc_intr from process_mbox_intr().

Signed-off-by: Manish Dusane <manish.dusane@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:45:31 +04:00
Nilesh Javali 320a61de9d [SCSI] qla4xxx: IDC implementation for Loopback
Handle IDC Request Notify AEN and post IDC Acknowledgement
while participating in Loopback IDC.

Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:41:53 +04:00
Vikas Chaudhary f8b0751de6 [SCSI] qla4xxx: Fix panic while rmmod
Issue:
System panic on rmmod if probe_adapter had failed during driver load.

Call Trace:
 [<ffffffffa071aa5a>] qla4xxx_abort_active_cmds+0x4a/0xa0 [qla4xxx]
 [<ffffffffa07224db>] qla4xxx_free_adapter+0x1b/0x1b0 [qla4xxx]
 [<ffffffffa073991f>] qla4xxx_remove_adapter+0x294/0x2c7 [qla4xxx]
 [<ffffffff812930b7>] pci_device_remove+0x37/0x70
 [<ffffffff8135006f>] __device_release_driver+0x6f/0xe0
 [<ffffffff813501a8>] driver_detach+0xc8/0xd0
 [<ffffffff8134ef0e>] bus_remove_driver+0x8e/0x110
 [<ffffffff81350972>] driver_unregister+0x62/0xa0
 [<ffffffff812933c4>] pci_unregister_driver+0x44/0xb0
 [<ffffffffa0739659>] qla4xxx_module_exit+0x15/0x47 [qla4xxx]
 [<ffffffff810addd4>] sys_delete_module+0x194/0x260
 [<ffffffff8150326e>] ? do_page_fault+0x3e/0xa0
 [<ffffffff8100b0f2>] system_call_fastpath+0x16/0x1b

Fix:
Do not cleanup resources on remove_adapter as they are cleaned up during
probe_adapter exit.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:40:47 +04:00
Poornima Vonti 7977f825a0 [SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails
If IRQ allocation fails, it means system has run out of interrupt
vectors, so fail probe_adapter in case of IRQ allocation failure
and dont retry adapter initialization.

Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:39:52 +04:00
Vikas Chaudhary 109a008bfe [SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX
For ISP82xx mixed interrupt mode is not supported.
Hence prevent MSI/MSI-x from falling back to INTx mode.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:38:55 +04:00
Vikas Chaudhary 39c9582601 [SCSI] qla4xxx: Update idc reg in case of PCI AER
Camram is reset by FW to default values after reboot/cold boot/pci reset.
In case of AER, PCI may need to reset so we need to set correct idc reg value
after PCIE error.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:37:48 +04:00
Poornima Vonti 8276190725 [SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery
Issue:
In qla4_8xxx_error_recovery() IDC lock recovery is initiated as
IDC lock is held while enabling the interrupts

Fix:
Correctly handle IDC locking mechanism in qla4_8xxx_error_recovery().

Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:36:39 +04:00
Vikas Chaudhary fbd8107cc9 [SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:27:46 +04:00
Vikas Chaudhary ecca51203b [SCSI] qla4xxx: Print correct IDC version
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:26:35 +04:00
Manish Dusane cfb27874ca [SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW
Signed-off-by: Manish Dusane <manish.dusane@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:25:13 +04:00
Vikas Chaudhary 56163c233d [SCSI] qla4xxx: Update driver version to 5.03.00-k0
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:11:08 +04:00
Vikas Chaudhary c68cdbf045 [SCSI] qla4xxx: Update Copyright header
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:11:08 +04:00
Vikas Chaudhary 6e7b429259 [SCSI] qla4xxx: Added support for ISP83XX
Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:11:08 +04:00
Vikas Chaudhary aec07caedb [SCSI] qla4xxx: Added new function qla4_8xxx_get_minidump
Move minidump code from qla4_8xxx_device_bootstrap() to
new function qla4_8xxx_get_minidump() to make code more
modular.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:11:07 +04:00
Vikas Chaudhary 83dbdf6f52 [SCSI] qla4xxx: Set IDC version in correct way
Issue:
   Device can go to READY state from COLD and skip INITIALIZATION,
   In this case driver will never set IDC version from function
   qla4_8xxx_device_bootstrap().

Fix:
1. Set IDC version at start of function qla4_82xx_need_reset_handler().
2. Set IDC version only if we are 1st driver to load.
3. Added new function qla4_8xxx_update_idc_reg() to set all idc reg at one
   place.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:11:07 +04:00
Vikas Chaudhary ee996a6917 [SCSI] qla4xxx: Replace all !is_qla8022() with is_qla40XX()
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:11:07 +04:00
Vikas Chaudhary 33693c7aab [SCSI] qla4xxx: Added new functions in isp_ops
Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:11:07 +04:00
Vikas Chaudhary c38fa3abea [SCSI] qla4xxx: Clean-up and optimize macros
Remove following unused define:-

QLA82XX_MINIDUMP_OCM0_SIZE
QLA82XX_MINIDUMP_L1C_SIZE
QLA82XX_MINIDUMP_L2C_SIZE
QLA82XX_MINIDUMP_COMMON_STR_SIZE
QLA82XX_MINIDUMP_FCOE_STR_SIZE
QLA82XX_MINIDUMP_MEM_SIZE
QLA82XX_MAX_ENTRY_HDR

Added following new define to optimize code:-

MIU_TA_CTL_WRITE_ENABLE
MIU_TA_CTL_WRITE_START
MIU_TA_CTL_START_ENABLE

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:11:07 +04:00
Vikas Chaudhary de8c72daa0 [SCSI] qla4xxx: Rename 82XX macros
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:11:06 +04:00
Vikas Chaudhary 5e9bcec792 [SCSI] qla4xxx: Update func name from ql4_ to qla4_
ql4_8xxx_mark_entry_skipped to qla4_8xxx_mark_entry_skipped
ql4_attr_is_visible to qla4_attr_is_visible

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:11:06 +04:00
Vikas Chaudhary 7664a1fd76 [SCSI] qla4xxx: Update structure and variable names
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:11:05 +04:00
Vikas Chaudhary f8086f4fd4 [SCSI] qla4xxx: Update function name from 8xxx to 82xx
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:11:05 +04:00
Vikas Chaudhary eafcde2103 [SCSI] qla4xxx: Update driver version to 5.02.00-k20
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:11:05 +04:00
Vikas Chaudhary da106212cb [SCSI] qla4xxx: Wait for cmd to complete before chip reset for ISP40XX
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:11:04 +04:00
Vikas Chaudhary d9e62e5130 [SCSI] qla4xxx: Clear interrupt while unloading driver.
while processing the stop firmware mailbox command on driver unload,
a interrupt is processed which causes kernel panic as the response
queue is not valid.

Fix is to clear the interrupt in free_adapter call just after
disabling the interrupts.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:11:04 +04:00
Vikas Chaudhary 8e9157c832 [SCSI] qla4xxx: Fix lockdep warning in qla4xxx_post_work()
Fix following lockdep warning:-

 INFO: trying to register non-static key.
 the code is fine but needs lockdep annotation.
 turning off the locking correctness validator.
 Pid: 298, comm: modprobe Not tainted 3.6.0-rc1+ #13
 Call Trace:
 [<c049f5c6>] register_lock_class+0x186/0x360
 [<c06e2e39>] ? __dev_printk+0x139/0x280
 [<c04a288a>] __lock_acquire+0x6a/0x450
 [<c04a2cf4>] lock_acquire+0x84/0xf0
 [<f98bb0d0>] ? qla4xxx_post_work+0x20/0x60 [qla4xxx]
 [<c089a05b>] _raw_spin_lock_irqsave+0x4b/0x60
 [<f98bb0d0>] ? qla4xxx_post_work+0x20/0x60 [qla4xxx]
 [<f98bb0d0>] qla4xxx_post_work+0x20/0x60 [qla4xxx]
 [<f98bb1c9>] qla4xxx_post_aen_work+0x49/0x60 [qla4xxx]
 [<f98c6cf2>] qla4xxx_isr_decode_mailbox+0x3f2/0x780 [qla4xxx]
 [<f98c8493>] qla4_83xx_interrupt_service_routine+0x33/0x50 [qla4xxx]
 [<f98d0e49>] qla4_83xx_process_mbox_intr+0x29/0x40 [qla4xxx]
 [<f98c2031>] qla4xxx_mailbox_command+0x361/0x5d0 [qla4xxx]
 [<c08983c8>] ? mutex_unlock+0x8/0x10
 [<f98c3e86>] qla4xxx_get_ifcb+0x66/0xb0 [qla4xxx]
 [<f98c3ef7>] qla4xxx_update_local_ifcb+0x27/0x100 [qla4xxx]
 [<f98c56af>] qla4xxx_initialize_fw_cb+0x2ff/0x3b0 [qla4xxx]
 [<c04150d0>] ? dma_generic_free_coherent+0x30/0x30
 [<f98c0f70>] qla4xxx_init_firmware+0x40/0xf0 [qla4xxx]
 [<f98c10b6>] qla4xxx_initialize_adapter+0x96/0x120 [qla4xxx]
 [<f98d35cd>] qla4xxx_probe_adapter+0x378/0x855 [qla4xxx]
 [<c04a1a04>] ? trace_hardirqs_on_caller+0xf4/0x180
 [<c04a1a9b>] ? trace_hardirqs_on+0xb/0x10
 [<c06ef403>] ? pm_runtime_enable+0x43/0x70
 [<c062f042>] local_pci_probe+0x42/0xb0
 [<c06300c0>] pci_device_probe+0x60/0x80
 [<c06e6bb6>] really_probe+0x56/0x2e0
 [<c089a5f2>] ? _raw_spin_unlock_irq+0x22/0x30
 [<c06f0b02>] ? pm_runtime_barrier+0x52/0xb0
 [<c06e6e77>] driver_probe_device+0x37/0x90
 [<c0898281>] ? mutex_lock_nested+0x31/0x40
 [<c06e6f51>] __driver_attach+0x81/0x90
 [<c06e51e8>] bus_for_each_dev+0x48/0x70
 [<c06e68e9>] driver_attach+0x19/0x20
 [<c06e6ed0>] ? driver_probe_device+0x90/0x90
 [<c06e637f>] bus_add_driver+0x18f/0x280
 [<c062ff40>] ? pci_dev_put+0x20/0x20
 [<c062ff40>] ? pci_dev_put+0x20/0x20
 [<c06e7435>] driver_register+0x65/0x120
 [<c061a3a2>] ? __raw_spin_lock_init+0x32/0x60
 [<c06302f4>] __pci_register_driver+0x54/0xc0
 [<f98e809e>] qla4xxx_module_init+0x9e/0xcd [qla4xxx]
 [<c040302f>] do_one_initcall+0x2f/0x170
 [<f98e8000>] ? 0xf98e7fff
 [<c04ae025>] sys_init_module+0x75/0x1c0
 [<c04a1a04>] ? trace_hardirqs_on_caller+0xf4/0x180
 [<c0609514>] ? trace_hardirqs_on_thunk+0xc/0x10
 [<c08a141f>] sysenter_do_call+0x12/0x38

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-24 12:11:04 +04:00
Vikas Chaudhary d53efb9d51 [SCSI] qla4xxx: Update driver version to 5.02.00-k19
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-14 17:59:22 +01:00
Lalit Chandivade 24c1420094 [SCSI] qla4xxx: Properly handle SCSI underrun while processing status IOCBs.
The current code would incorrectly return a DID_OK for a
CHECK CONDITION with Recovered error sense key causing incorrect
completion of a command when there is a dropped frame.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-14 17:59:21 +01:00
Manish Rangankar 80c53e649d [SCSI] qla4xxx: Fix multiple conn login event issue during session recovery.
During iscsid session recovery driver sends multiple ISCSI_CONN_STATE_LOGGED_IN
event from qla4xxx_conn_start() and qla4xxx_ddb_change(), which causes iscsid
to crash.

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-14 17:59:21 +01:00
Vikas Chaudhary 26fdf92297 [SCSI] qla4xxx: Fix gcc warning for x86 system
Fix warning:-
drivers/scsi/qla4xxx/ql4_nx.c:1867:2: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 5 has type ‘uint32_t’ [-Wformat]

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-14 17:59:20 +01:00
Manish Rangankar d46bdeb144 [SCSI] qla4xxx: Fix memory corruption issue in qla4xxx_ep_connect.
In qla4xxx_ep_connect(), qla_ep->dst_addr and dst_addr are type
struct sockaddr. We are copying sizeof(struct sockaddr_in6) bytes
from dst_addr to qla_ep->dst_addr which is 12 bytes larger. This
will cause memory corruption. So we change qla_ep->dst_addr to
struct sockaddr_storage which is of 128 byte, large enough to
hold sizeof(struct sockaddr_in6).

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-14 17:59:19 +01:00
Bjorn Helgaas 1959ec5f82 Merge branch 'pci/stephen-const' into next
* pci/stephen-const:
  make drivers with pci error handlers const
  scsi: make pci error handlers const
  netdev: make pci_error_handlers const
  PCI: Make pci_error_handlers const
2012-09-12 13:54:10 -06:00
Stephen Hemminger a55b2d21e8 scsi: make pci error handlers const
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-09-07 16:35:00 -06:00
Masanari Iida 59e13d4833 scsi: fix various printk and comment typos
Correct spelling typo within drivers/scsi

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-09-01 08:24:35 -07:00
Jiang Liu 5548bfd0ee [SCSI] qla4xxx: Use PCI Express Capability accessors
Use PCI Express Capability access functions to simplify qla4xxx driver.

Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2012-08-23 10:11:15 -06:00
Jon Mason 983bfb5b40 [SCSI] qla4xxx: remove unnecessary read of PCI_CAP_ID_EXP
The PCIE capability offset is saved during PCI bus walking.  It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.

Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:59:02 +01:00
Vikas Chaudhary efb6c717b7 [SCSI] qla4xxx: Update driver version to 5.02.00-k18
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:35 +01:00
Vikas Chaudhary 18e2df938c [SCSI] qla4xxx: Fix Spell check.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:35 +01:00
Vikas Chaudhary 68b6d5d3d1 [SCSI] qla4xxx: Fix a Sparse warning message
Fix following message:-
drivers/scsi/qla4xxx/ql4_os.c:3266:5: error: symbol 'qla4xxx_post_aen_work' redeclared with different type (originally declared at drivers/scsi/qla4xxx/ql4_glbl.h:186) - incompatible argument 2 (different signedness)

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:34 +01:00
Vikas Chaudhary 1cb78d73d3 [SCSI] qla4xxx: multi-session fix for flash ddbs
Allow multi-session to target (for flash ddbs) accesible via
multiple network portal

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:34 +01:00
Vikas Chaudhary 356293bc7e [SCSI] qla4xxx: Update driver version to 5.02.00-k17
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-30 13:01:34 +04:00
Tej Parkash 068237c87c [SCSI] qla4xxx: Capture minidump for ISP82XX on firmware failure
Added support to capture dump (Minidump) which allows us to
catpure a snapshot of the firmware/hardware states at the time
of firmware failure

Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-30 13:00:28 +04:00
Tej Parkash f7b4aa6365 [SCSI] qla4xxx: Add change_queue_depth API support
change_queue_depth will adjust device queuedepth upon receiving
"SAM_STAT_TASK_SET_FULL" scsi status from the target.
Also added ql4xqfulltracking command line param to enable or disable
queuefull tracking. One can disabling queuefull tracking to ensure
user set scsi device queuedepth is not altered.

Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-30 12:59:26 +04:00
Manish Rangankar 90599b62ca [SCSI] qla4xxx: Fix clear ddb mbx command failure issue.
Allow ddb state to change to DDB_DS_NO_CONNECTION_ACTIVE or
DDB_DS_SESSION_FAILED before issuing clear ddb mailbox cmd,
because clear ddb mailbox cmd fails if the ddb state is not
equal to DDB_DS_NO_CONNECTION_ACTIVE or DDB_DS_SESSION_FAILED.

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-30 12:58:30 +04:00
Manish Rangankar 3d948e2a21 [SCSI] qla4xxx: Fix kernel panic during discovery logout.
Update the session and connection parameter before sending
connection logged in event to iscsiadm because in some
scenario logout may come in just after we send the logged
in event to user, which free up session, connection and ddb,
but DPC is still updating session and connect parameter
which can lead to panic.

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-30 12:56:08 +04:00
Lalit Chandivade 5f50aa3ad5 [SCSI] qla4xxx: Correct early completion of pending mbox.
Check for Firmware Hang (AF_FW_RECOVERY) after mailbox command
has gained access to ensure that the mailbox command does not
wait un-necessarily during a firmware recovery and prevent
premature mailbox timeout which will lead to back to back reset's.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-30 12:53:52 +04:00
Linus Torvalds a75ee6ecd4 SCSI updates on 20120331
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQEcBAABAgAGBQJPdrIWAAoJEDeqqVYsXL0Mny4IAMTzXGOXCykpWhdIe2R8w0Ys
 eIoTJhBKoQWnLTV8cOODtwmtZcoQLeXkZmizZiAJvX6O1tOgueg+W4AFa9grxXGI
 O0d1bSb2ardzU7VZrZSY60Hd4bylMwn4Xv/0dRrQMwTJO0LEeGWsJPV2+2BuXwMB
 lGCNB67oUBXgMOI1jUZQRwx/mBzQ3e/gINjnpZTNKHia7YkX/yVTFISq7htgfDN7
 1wRGxymbHtVap3NbtUO96BUUndAiF5vom+4WNvaQUyPrCc6aoGWjv+J9DQXY/zgv
 AYjujAluK396D6YncGFAWBzYOg9WFbq54v0PRUanjcTTAu5ILs2BxqWdhmnvl14=
 =IH8T
 -----END PGP SIGNATURE-----

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6

Pull SCSI updates from James Bottomley:
 "This is primarily another round of driver updates (lpfc, bfa, fcoe,
  ipr) plus a new ufshcd driver.  There shouldn't be anything
  controversial in here (The final deletion of scsi proc_ops which
  caused some build breakage has been held over until the next merge
  window to give us more time to stabilise it).

  I'm afraid, with me moving continents at exactly the wrong time,
  anything submitted after the merge window opened has been held over to
  the next merge window."

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (63 commits)
  [SCSI] ipr: Driver version 2.5.3
  [SCSI] ipr: Increase alignment boundary of command blocks
  [SCSI] ipr: Increase max concurrent oustanding commands
  [SCSI] ipr: Remove unnecessary memory barriers
  [SCSI] ipr: Remove unnecessary interrupt clearing on new adapters
  [SCSI] ipr: Fix target id allocation re-use problem
  [SCSI] atp870u, mpt2sas, qla4xxx use pci_dev->revision
  [SCSI] fcoe: Drop the rtnl_mutex before calling fcoe_ctlr_link_up
  [SCSI] bfa: Update the driver version to 3.0.23.0
  [SCSI] bfa: BSG and User interface fixes.
  [SCSI] bfa: Fix to avoid vport delete hang on request queue full scenario.
  [SCSI] bfa: Move service parameter programming logic into firmware.
  [SCSI] bfa: Revised Fabric Assigned Address(FAA) feature implementation.
  [SCSI] bfa: Flash controller IOC pll init fixes.
  [SCSI] bfa: Serialize the IOC hw semaphore unlock logic.
  [SCSI] bfa: Modify ISR to process pending completions
  [SCSI] bfa: Add fc host issue lip support
  [SCSI] mpt2sas: remove extraneous sas_log_info messages
  [SCSI] libfc: fcoe_transport_create fails in single-CPU environment
  [SCSI] fcoe: reduce contention for fcoe_rx_list lock [v2]
  ...
2012-03-31 13:31:23 -07:00
Sergei Shtylyov 7d7311c445 [SCSI] atp870u, mpt2sas, qla4xxx use pci_dev->revision
commit 44c10138fd (PCI: Change all
drivers to use pci_device->revision) converted all drivers to use
pci_dev->revision.  Convert these three drivers which got missed.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-03-28 14:36:37 +01:00
Vikas Chaudhary 6d76222e1a [SCSI] qla4xxx: Update driver version to 5.02.00-k16
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-03-27 08:26:35 +01:00
Vikas Chaudhary 1a590cabc2 [SCSI] iscsi_transport: Added error status code for ping comp event
Defined error codes for ping completion status.

This patch take care of Mike Christie's commets

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-03-27 08:26:35 +01:00
Vikas Chaudhary e16d166e4f [SCSI] qla4xxx: assign correct address for iscsi_cls_host
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-03-27 08:26:34 +01:00
Petr Uzel 0bd7f84211 [SCSI] qla4xxx: Add missing spaces to error messages
Signed-off-by: Petr Uzel <petr.uzel@suse.cz>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-03-27 08:26:28 +01:00
Linus Torvalds 424a6f6ef9 SCSI updates on 20120319
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQEcBAABAgAGBQJPZxSnAAoJEDeqqVYsXL0M0Y4IAMX0vrTVZbg6psA5/gMcWGRP
 CkFXEQ8n0PL2SCaj6BoDqamJFe5Nc7dnqxM0fGawB4S9vr3rHhiOlwO+NbV9zFYC
 2skBTpeL3sjgtN/jTBdfeeAa7xTYpu/XGyei0NS1A5c2AyMVXV0uYV2s4VNZxe44
 tVIn1OEzM2giZ9EB1OZslDMrg5XXm3MBIUECP0LbWUhBm/35caSFKzMXRwhh7WiK
 +AVmc2AZYtdEwuknDyiH7KlsaoB3vGL9pPrAUJzIgEhy2pOo2A7W72HfA4Fj+y6a
 uF9HBS5zciMp1+sGWry62AjNbWgin9BRlozBEO/lJhIfMGDV1nXEIJsOkOgkdoE=
 =1TxB
 -----END PGP SIGNATURE-----

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6

SCSI updates from James Bottomley:
 "The update includes the usual assortment of driver updates (lpfc,
  qla2xxx, qla4xxx, bfa, bnx2fc, bnx2i, isci, fcoe, hpsa) plus a huge
  amount of infrastructure work in the SAS library and transport class
  as well as an iSCSI update.  There's also a new SCSI based virtio
  driver."

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (177 commits)
  [SCSI] qla4xxx: Update driver version to 5.02.00-k15
  [SCSI] qla4xxx: trivial cleanup
  [SCSI] qla4xxx: Fix sparse warning
  [SCSI] qla4xxx: Add support for multiple session per host.
  [SCSI] qla4xxx: Export CHAP index as sysfs attribute
  [SCSI] scsi_transport: Export CHAP index as sysfs attribute
  [SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
  [SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
  [SCSI] pm8001: fix endian issue with code optimization.
  [SCSI] pm8001: Fix possible racing condition.
  [SCSI] pm8001: Fix bogus interrupt state flag issue.
  [SCSI] ipr: update PCI ID definitions for new adapters
  [SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
  [SCSI] isci: improvements in driver unloading routine
  [SCSI] isci: improve phy event warnings
  [SCSI] isci: debug, provide state-enum-to-string conversions
  [SCSI] scsi_transport_sas: 'enable' phys on reset
  [SCSI] libsas: don't recover end devices attached to disabled phys
  [SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
  [SCSI] libsas: set attached device type and target protocols for local phys
  ...
2012-03-22 12:55:29 -07:00
Linus Torvalds 69a7aebcf0 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree from Jiri Kosina:
 "It's indeed trivial -- mostly documentation updates and a bunch of
  typo fixes from Masanari.

  There are also several linux/version.h include removals from Jesper."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits)
  kcore: fix spelling in read_kcore() comment
  constify struct pci_dev * in obvious cases
  Revert "char: Fix typo in viotape.c"
  init: fix wording error in mm_init comment
  usb: gadget: Kconfig: fix typo for 'different'
  Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c"
  writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header
  writeback: fix typo in the writeback_control comment
  Documentation: Fix multiple typo in Documentation
  tpm_tis: fix tis_lock with respect to RCU
  Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c"
  Doc: Update numastat.txt
  qla4xxx: Add missing spaces to error messages
  compiler.h: Fix typo
  security: struct security_operations kerneldoc fix
  Documentation: broken URL in libata.tmpl
  Documentation: broken URL in filesystems.tmpl
  mtd: simplify return logic in do_map_probe()
  mm: fix comment typo of truncate_inode_pages_range
  power: bq27x00: Fix typos in comment
  ...
2012-03-20 21:12:50 -07:00
Vikas Chaudhary cd8df932d8 [SCSI] qla4xxx: Update driver version to 5.02.00-k15
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 17:03:03 -06:00
Vikas Chaudhary 3573bfb230 [SCSI] qla4xxx: trivial cleanup
1. Do not initialise globals to 0
 2. Fix wrong spelling in debug message
 3. Modified debug log messages

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 17:02:10 -06:00
Vikas Chaudhary a7380a6531 [SCSI] qla4xxx: Fix sparse warning
Fix following warning:-
drivers/scsi/qla4xxx/ql4_os.c:35:5: warning: symbol 'ql4xdisablesysfsboot' was not declared. Should it be static?

drivers/scsi/qla4xxx/ql4_iocb.c:461:5: warning: symbol 'qla4xxx_send_mbox_iocb' was not declared. Should it be static?

drivers/scsi/qla4xxx/ql4_os.c:3025:6: warning: symbol 'qla4xxx_do_work' was not declared. Should it be static?

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 17:01:14 -06:00
Manish Rangankar 173269ef29 [SCSI] qla4xxx: Add support for multiple session per host.
This patch will allow iscsiadm to create multiple session
for the same target on per host.

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 17:00:24 -06:00
Mike Christie fca9f04d46 [SCSI] qla4xxx: Export CHAP index as sysfs attribute
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 16:59:19 -06:00
Nilesh Javali 376738af50 [SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
For offload iSCSI like qla4xxx CHAP entries are stored in FLASH.
This patch adds support to list CHAP entries stored in FLASH and
delete specified CHAP entry from FLASH using iscsi tools.

Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 16:57:20 -06:00
Petr Uzel 0973dac1a1 qla4xxx: Add missing spaces to error messages
Signed-off-by: Petr Uzel <petr.uzel@suse.cz>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-02-28 16:03:48 +01:00
Hitoshi Mitake 797a796a13 asm-generic: architecture independent readq/writeq for 32bit environment
This provides unified readq()/writeq() helper functions for 32-bit
drivers.

For some cases, readq/writeq without atomicity is harmful, and order of
io access has to be specified explicitly.  So in this patch, new two
header files which contain non-atomic readq/writeq are added.

 - <asm-generic/io-64-nonatomic-lo-hi.h> provides non-atomic readq/
   writeq with the order of lower address -> higher address

 - <asm-generic/io-64-nonatomic-hi-lo.h> provides non-atomic readq/
   writeq with reversed order

This allows us to remove some readq()s that were added drivers when the
default non-atomic ones were removed in commit dbee8a0aff ("x86:
remove 32-bit versions of readq()/writeq()")

The drivers which need readq/writeq but can do with the non-atomic ones
must add the line:

  #include <asm-generic/io-64-nonatomic-lo-hi.h> /* or hi-lo.h */

But this will be nop in 64-bit environments, and no other #ifdefs are
required.  So I believe that this patch can solve the problem of
 1. driver-specific readq/writeq
 2. atomicity and order of io access

This patch is tested with building allyesconfig and allmodconfig as
ARCH=x86 and ARCH=i386 on top of tip/master.

Cc: Kashyap Desai <Kashyap.Desai@lsi.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Cc: James Bottomley <James.Bottomley@parallels.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: James Bottomley <jbottomley@parallels.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hitoshi Mitake <h.mitake@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-02-21 16:47:28 -08:00
Vikas Chaudhary cf3059a129 [SCSI] qla4xxx: Update driver version to 5.02.00-k14
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 09:36:01 -06:00
Vikas Chaudhary c0b9d3f750 [SCSI] qla4xxx: Added ping support
Added ping support for network connection diagnostics.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 09:35:23 -06:00
Vikas Chaudhary ff88443080 [SCSI] qla4xxx: added support for host event
Added support to post kernel host event to application using
netlink interface.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 09:34:04 -06:00
Vikas Chaudhary 46801ba698 [SCSI] qla4xxx: Proper detection of firmware abort error code for ISP82xx
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 09:33:01 -06:00
Lalit Chandivade badc5b9996 [SCSI] qla4xxx: Remove un-necessary print statment
On ROM lock acquiring timeout failure, driver spews lot of warning
messages in a for loop, remove the unwanted warning message to reduce
kernel messages clutter.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 09:32:38 -06:00
Manish Rangankar e8fb00e068 [SCSI] qla4xxx: Modified debug log messages for boot info.
In some configurations user may not have boot targets configured.
In such cases the debug messages printed out by driver look like
some kind of failure happening. However this could be a valid
case, so modified the messages to appear as warning messages
versus failure messages.

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 09:32:12 -06:00
Lalit Chandivade 20e835b43f [SCSI] qla4xxx: Fix verify boot idx correctly
qla4xxx_verify_boot_idx can falsely report a DDB to be boot target
if ha->pri_ddb_idx and ha->sec_ddb_idx are not initialized correctly.
What this could cause is if there is DDB entry in FLash at index 0, then
qla4xxx_verify_boot_idx would return wrong result as ha->pri_ddb_idx is not
set correctly. Fixed the qla4xxx_get_boot_info to set the ha->pri_ddb_idx and
ha->sec_ddb_idx correctly.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 09:31:46 -06:00
Lalit Chandivade 981c982c2d [SCSI] qla4xxx: Fix un-necessary delay on invalid DDB
Fix the un-necessary wait for completion of a sendtarget on an
invalid DDB entry. The state of an invalid DDB entry is 0 (unassigned)

This will also avoid the delays during system boot.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 09:31:18 -06:00
Vikas Chaudhary 45857216f2 [SCSI] qla4xxx: Remove unused code
This code initially added for FW debugging, we don't need this
code now so taking it out.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 09:30:36 -06:00
Vikas Chaudhary 26b937b2a3 [SCSI] qla4xxx: Update driver version to 5.02.00-k13
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 08:08:55 -06:00
Vikas Chaudhary 3254dbe9d9 [SCSI] qla4xxx: Added support to show port_state and port_speed in sysfs
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 08:08:54 -06:00
Vikas Chaudhary 6c1b8789b0 [SCSI] qla4xxx: Added support to show targetalias in sysfs
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 08:08:54 -06:00
Vikas Chaudhary 19b628dfc6 [SCSI] qla4xxx: Update driver version to 5.02.00-k12
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 12:36:13 +04:00
Karen Higgins a4e8a715a3 [SCSI] qla4xxx: Cleanup modinfo display
Beautify modinfo display. Display correct info for ql4xextended_error_logging

[jejb: fixup checkpatch warning]
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 12:35:22 +04:00
Sarang Radke 7876499932 [SCSI] qla4xxx: Clear the RISC interrupt bit during FW init
This patch fix kernel panic during kdump.

Signed-off-by: Sarang Radke <sarang.radke@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 12:33:24 +04:00
Nilesh Javali 527c8b2e96 [SCSI] qla4xxx: Added error logging for firmware abort
Added debug print with error code in case of firmware error.

Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 12:32:58 +04:00
Giridhar Malavali e6bd0ebd4a [SCSI] qla4xxx: Disable generating pause frames in case of FW hung
In case of FW hung  ISP82xx generates continuous pause frames
which causes switch to disable port.
Added fix to disable generating pause frames in case of
FW hung

Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 12:32:08 +04:00
Mike Hernandez 4f77083ed0 [SCSI] qla4xxx: Temperature monitoring for ISP82XX core.
During watchdog, need to monitor temperature of ISP82XX core
and set device state to FAILED when temperature reaches
"Panic" level.

Signed-off-by: Mike Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 12:30:59 +04:00
Vikas Chaudhary 3a19cbf530 [SCSI] qla4xxx: Update driver version to 5.02.00-k11
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-10 17:01:23 -06:00
Manish Rangankar 368d45cc61 [SCSI] qla4xxx: Fixed BFS with sendtargets as boot index.
If ql4xdisablesysfsboot = 0 and sendtargets entry as boot index then
driver does export sendtarget entries in sysfs but iscsistart does not
do discovery. So in this case let driver do the discovery and
login to the targets.

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-10 17:01:23 -06:00
Nilesh Javali f1f2e60e1a [SCSI] qla4xxx: Break the loop if the sendtargets list was empty
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-10 17:01:22 -06:00
Nilesh Javali c28eaaca7a [SCSI] qla4xxx: Limit the ACB Default Timeout value to 12s
A wrong default timeout value programmed in the adapter causes driver
to wait for that much time while waiting for target discoveries to complete.
This could add huge delays during the driver load time. To avoid this,
limit the default timeout value to 12 seconds if the default timeout value
set in adapter is less than 12 seconds and greater than 120 seconds.

Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-10 17:01:22 -06:00
Lalit Chandivade 4a4bc2e90c [SCSI] qla4xxx: cleanup, make qla4xxx_build_ddb_list short
Make qla4xxx_build_ddb_list shorter by adding more helper functions.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-10 17:01:22 -06:00
Linus Torvalds d04baa157d SCSI updates for post 3.2 merge window
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQEcBAABAgAGBQJPBh1uAAoJEDeqqVYsXL0MnxIIAJl0SLxgX3Vo18jhv7epNaUy
 Akm8VcLTjW99IAZm1x166pGjLvdeZJC5A50DxW3jQMknKYZyyxEmTGOOMVA/LuCS
 J3V18tMrsEA7i1kEGx2MauRRNAvReAZl4a/nHuRc+hpVmfyQegBv1v4V0v0gzD5I
 MDZSSksqtXpJhsHt2B4g/jao7RhuJYXw7NidRGzEtksax3NMyWzaIb/75Uq6eenE
 HwJwCUgZZxxfRKksj/T8ShRE6BKL9wcvrm8SVNjBYF2OpnMUNCXtfLQ4fqbHtGz2
 otWvoQxVERehPZhTWHk6QnLgPwBWYyIUK7ErSFMTb9EK8b3FsEZkw6/LlS/lXnI=
 =Zopk
 -----END PGP SIGNATURE-----

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6

SCSI updates for post 3.2 merge window

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (67 commits)
  [SCSI] lpfc 8.3.28: Update driver version to 8.3.28
  [SCSI] lpfc 8.3.28: Add Loopback support for SLI4 adapters
  [SCSI] lpfc 8.3.28: Critical Miscellaneous fixes
  [SCSI] Lpfc 8.3.28: FC and SCSI Discovery Fixes
  [SCSI] lpfc 8.3.28: Add support for ABTS failure handling
  [SCSI] lpfc 8.3.28: SLI fixes and added SLI4 support
  [SCSI] lpfc 8.3.28: Miscellaneous fixes in sysfs and mgmt interfaces
  [SCSI] mpt2sas: Removed redundant calling of _scsih_probe_devices() from _scsih_probe
  [SCSI] mac_scsi: Remove obsolete IRQ_FLG_* users
  [SCSI] qla4xxx: Update driver version to 5.02.00-k10
  [SCSI] qla4xxx: check for FW alive before calling chip_reset
  [SCSI] qla4xxx: Fix qla4xxx_dump_buffer to dump buffer correctly
  [SCSI] qla4xxx: Fix the IDC locking mechanism
  [SCSI] qla4xxx: Wait for disable_acb before doing set_acb
  [SCSI] qla4xxx: Don't recover adapter if device state is FAILED
  [SCSI] qla4xxx: fix call trace on rmmod with ql4xdontresethba=1
  [SCSI] qla4xxx: Fix CPU lockups when ql4xdontresethba set
  [SCSI] qla4xxx: Perform context resets in case of context failures.
  [SCSI] iscsi class: export pid of process that created
  [SCSI] mpt2sas: Remove unused duplicate diag_buffer_enable param
  ...
2012-01-10 10:36:08 -08:00
Linus Torvalds 98793265b4 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
  Kconfig: acpi: Fix typo in comment.
  misc latin1 to utf8 conversions
  devres: Fix a typo in devm_kfree comment
  btrfs: free-space-cache.c: remove extra semicolon.
  fat: Spelling s/obsolate/obsolete/g
  SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
  tools/power turbostat: update fields in manpage
  mac80211: drop spelling fix
  types.h: fix comment spelling for 'architectures'
  typo fixes: aera -> area, exntension -> extension
  devices.txt: Fix typo of 'VMware'.
  sis900: Fix enum typo 'sis900_rx_bufer_status'
  decompress_bunzip2: remove invalid vi modeline
  treewide: Fix comment and string typo 'bufer'
  hyper-v: Update MAINTAINERS
  treewide: Fix typos in various parts of the kernel, and fix some comments.
  clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
  gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
  leds: Kconfig: Fix typo 'D2NET_V2'
  sound: Kconfig: drop unknown symbol ARCH_CLPS7500
  ...

Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
2012-01-08 13:21:22 -08:00
Al Viro 587a1f1659 switch ->is_visible() to returning umode_t
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2012-01-03 22:54:55 -05:00
Vikas Chaudhary 7b12859ae4 [SCSI] qla4xxx: Update driver version to 5.02.00-k10
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-12-15 10:57:43 +04:00
Shyam Sunder 9ee91a38b1 [SCSI] qla4xxx: check for FW alive before calling chip_reset
Check for firmware alive and do premature completion of
mbox commands in case of FW hung before doing chip_reset

Signed-off-by: Shyam Sunder <shyam.sunder@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-12-15 10:57:42 +04:00
Vikas Chaudhary 0a24361566 [SCSI] qla4xxx: Fix qla4xxx_dump_buffer to dump buffer correctly
KERN_INFO in printk adding new line character that mess-up
dump print format. Remove KERN_INFO to fix dump format.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-12-15 10:57:42 +04:00
Nilesh Javali e3f37d1636 [SCSI] qla4xxx: Fix the IDC locking mechanism
This ensures the transition of dev_state from COLD to
INITIALIZING is within lock and atomic.

Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-12-15 10:57:42 +04:00
Vikas Chaudhary ce505f9d1d [SCSI] qla4xxx: Wait for disable_acb before doing set_acb
In function qla4xxx_iface_set_param wait for disable_acb to
complete so that set_acb will not fail.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-12-15 10:57:42 +04:00
Sarang Radke 8e0f3a66a2 [SCSI] qla4xxx: Don't recover adapter if device state is FAILED
Multiple reset request don't get handled correctly as
the driver tries to recover adapter which is in FAILED state.

Signed-off-by: Sarang Radke <sarang.radke@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-12-15 10:57:41 +04:00
Sarang Radke 8a28896019 [SCSI] qla4xxx: fix call trace on rmmod with ql4xdontresethba=1
abort all active commands from eh_host_reset in-case
of ql4xdontresethba=1

Fix following call trace:-
Nov 21 14:50:47 172.17.140.111 qla4xxx 0000:13:00.4: qla4_8xxx_disable_msix: qla4xxx (rsp_q)
Nov 21 14:50:47 172.17.140.111 qla4xxx 0000:13:00.4: PCI INT A disabled
Nov 21 14:50:47 172.17.140.111 slab error in kmem_cache_destroy(): cache `qla4xxx_srbs': Can't free all objects
Nov 21 14:50:47 172.17.140.111 Pid: 9154, comm: rmmod Tainted: G           O 3.2.0-rc2+ #2
Nov 21 14:50:47 172.17.140.111 Call Trace:
Nov 21 14:50:47 172.17.140.111  [<c051231a>] ? kmem_cache_destroy+0x9a/0xb0
Nov 21 14:50:47 172.17.140.111  [<c0489c4a>] ? sys_delete_module+0x14a/0x210
Nov 21 14:50:47 172.17.140.111  [<c04fd552>] ? do_munmap+0x202/0x280
Nov 21 14:50:47 172.17.140.111  [<c04a6d4e>] ? audit_syscall_entry+0x1ae/0x1d0
Nov 21 14:50:47 172.17.140.111  [<c083019f>] ? sysenter_do_call+0x12/0x28
Nov 21 14:51:50 172.17.140.111 SLAB: cache with size 64 has lost its name
Nov 21 14:51:50 172.17.140.111 iscsi: registered transport (qla4xxx)
Nov 21 14:51:50 172.17.140.111 qla4xxx 0000:13:00.4: PCI INT A -> GSI 28 (level, low) -> IRQ 28

Signed-off-by: Sarang Radke <sarang.radke@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-12-15 10:57:41 +04:00
Mike Hernandez 9acf753393 [SCSI] qla4xxx: Fix CPU lockups when ql4xdontresethba set
Fix issue where CPU lockup is seen when ql4xdontresethba is set and
driver is "stuck" in NEED_RESET state handler.

Signed-off-by: Mike Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-12-15 10:57:41 +04:00
Vikas Chaudhary 4c6a794d2c [SCSI] qla4xxx: Perform context resets in case of context failures.
For 4032, context reset was the same as chip reset, and any firmware
issue was recovered by performing a chip reset.
For 82xx, the iSCSI firmware runs along with FCoE and the NIC
firmware contexts, and an error encountered doesnot essentially mean
that a chip reset is necessary.

Perform Chip resets only in the following cases:
1. Mailbox system error.
2. Mailbox command timeout.
3. fw_heartbeat_counter counter stops incrementing.

For all other cases, only perform a context reset.
1. Command Completion with an invalid srb.
2. Other mailbox failures.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Shyam Sunder <shyam.sunder@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-12-15 10:57:41 +04:00
Mike Christie ff1d0319ac [SCSI] qla4xxx: check for failed conn setup
iscsi_conn_setup can fail so we must check for NULL being
returned.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-12-14 15:40:44 +04:00
Tomas Henzl e1cd89c507 [SCSI] qla4xxx: a small loop fix
When the qla4xxx_get_fwddb_entry returns QLA_ERROR
the nex_idx is not updated,
      for (idx = 0; idx < max_ddbs; idx = next_idx) {
                ret = qla4xxx_get_fwddb_entry(ha, idx, NULL, 0, NULL,
                                              &next_idx, &state, &conn_err,
                                                NULL, NULL);
                if (ret == QLA_ERROR)
                        continue;

This means there is a risk that the 'idx < max_ddbs' condition will never
met and the loop will loop forever.
Fix this by explicitly increasing the next_idx in the error condition.

Maybe a break instead of continue is more appropriate, leaving the decision
on the qlogic maintainer.

Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-12-14 15:40:43 +04:00
Mike Christie 13483730a1 [SCSI] qla4xxx: fix flash/ddb support
With open-iscsi support, target entries persisted in the FLASH were not
login. Added support in the qla4xxx driver to do the login on probe
time to the target entries saved in the FLASH by user.
With this changes upgrade to the new kernel with open-iscsi support in
qla4xxx will ensure users original target entries login on driver load

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-12-14 15:40:43 +04:00
Justin P. Mattock 42b2aa86c6 treewide: Fix typos in various parts of the kernel, and fix some comments.
The below patch fixes some typos in various parts of the kernel, as well as fixes some comments.
Please let me know if I missed anything, and I will try to get it changed and resent.

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-12-02 14:57:31 +01:00
Linus Torvalds ec7ae51753 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (204 commits)
  [SCSI] qla4xxx: export address/port of connection (fix udev disk names)
  [SCSI] ipr: Fix BUG on adapter dump timeout
  [SCSI] megaraid_sas: Fix instance access in megasas_reset_timer
  [SCSI] hpsa: change confusing message to be more clear
  [SCSI] iscsi class: fix vlan configuration
  [SCSI] qla4xxx: fix data alignment and use nl helpers
  [SCSI] iscsi class: fix link local mispelling
  [SCSI] iscsi class: Replace iscsi_get_next_target_id with IDA
  [SCSI] aacraid: use lower snprintf() limit
  [SCSI] lpfc 8.3.27: Change driver version to 8.3.27
  [SCSI] lpfc 8.3.27: T10 additions for SLI4
  [SCSI] lpfc 8.3.27: Fix queue allocation failure recovery
  [SCSI] lpfc 8.3.27: Change algorithm for getting physical port name
  [SCSI] lpfc 8.3.27: Changed worst case mailbox timeout
  [SCSI] lpfc 8.3.27: Miscellanous logic and interface fixes
  [SCSI] megaraid_sas: Changelog and version update
  [SCSI] megaraid_sas: Add driver workaround for PERC5/1068 kdump kernel panic
  [SCSI] megaraid_sas: Add multiple MSI-X vector/multiple reply queue support
  [SCSI] megaraid_sas: Add support for MegaRAID 9360/9380 12GB/s controllers
  [SCSI] megaraid_sas: Clear FUSION_IN_RESET before enabling interrupts
  ...
2011-10-28 16:44:18 -07:00
Mike Christie 590134fa78 [SCSI] qla4xxx: export address/port of connection (fix udev disk names)
Udev uses the connection's persistent address/port in the
/dev/disk/by-path name. qla4xxx is not exporting this value
so its iscsi disk names have been lacking the iscsi info.
In the old driver we did not have this information but
we do now and can fix this by just setting the flags to tell
libiscsi/scsi_transport_iscsi to export this info in sysfs.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-20 10:28:16 -05:00
Mike Christie 2d63673b4d [SCSI] iscsi class: fix vlan configuration
Userspace was sending the priority/id part of the vlan tag
and sysfs was displaying the id in the vlan file. This
renames the vlan sysfs file to vlan_id to reflect that it
was showing the id and to match the vlan_priority file.
This also adds a ISCSI_NET_PARAM_VLAN_TAG iscsi nl command
to relfect that we are sending down the vlan/priority
part of the tag.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-20 10:13:55 -05:00
Mike Christie 00c31889f7 [SCSI] qla4xxx: fix data alignment and use nl helpers
This has the driver use helpers for a common operation and fixes
a issue where if multiple iscsi params are sent they could be
sent at offsets that cause unaligned accesses. The nla helpers
account for the padding needed to align properly for the driver.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-20 10:12:44 -05:00
Vikas Chaudhary a748dcc2b1 [SCSI] qla4xxx: Update driver version to 5.02.00-k8
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-16 11:12:08 -05:00
Manish Rangankar 0d5b36b8b4 [SCSI] qla4xxx: updated device id check for BFS.
JIRA Key: UPSISCSI-75

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-16 11:11:49 -05:00
Manish Rangankar 69ca216e9b [SCSI] qla4xxx: Fixed target discovery failed issue.
When sendtargets response is greater then max receive data segment length,
the passthrough IOCB failed with data overrun status. Solution is to
allocate space for iSCSI header in the IOCB response buffer.

JIRA Key: UPSISCSI-147

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-16 11:11:22 -05:00
Manish Rangankar f922da79fd [SCSI] qla4xxx: Fixed active session re-open issue.
When iscsid restarted for an existing active session, set DDB will
fail with status already logged in. In this case, we have to send
logged in event to iscsid.

JIRA Key: OPENISCSI-21

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-16 11:11:06 -05:00
Manish Rangankar 5283bfb64e [SCSI] qla4xxx: Fixed device blocked issue on link up-down.
Devices are getting blocked during continuous link up and down.
Solution is, during relogin unblock the session, using iscsi_conn_start,
before sending connection logged in event.

JIRA Key: UPSISCSI-138

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-16 11:10:45 -05:00
Manish Rangankar 98270ab45c [SCSI] qla4xxx: Fixed session destroy issue on link up-down.
During link down, iscsid tries to do re-login to failed session. In case of
link down-up-down, LLD was sending connection login failed event to iscsid,
which is destroying the session, instead we have to continue re-login by
sending connection err event.

JIRA Key: UPSISCSI-134

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-16 11:10:27 -05:00
Manish Rangankar 736cf369c9 [SCSI] qla4xxx: Clear DDB map index on the basis of AEN.
Unable to login to session if login-logout issued consecutively for
multiple sessions. Solution is to clear idx in DDB map on the basis
of no-active connection asynchronous event (AEN).

JIRA Key: UPSISCSI-135

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-16 11:10:06 -05:00
Lalit Chandivade 166dd20d79 [SCSI] qla4xxx: Free Device Database (DDB) reserved by FW
Firmware reserves DDBs if there are entries in the FLASH.
So there are no free DDBs left when a iSCSI login is initiated
by user space tool like iscsiadm.
Since now login is not controlled by firmware, LLD need to free
up the DDBs after firmware init. This will ensure free DDBs are
available for iSCSI logins using iscsiadm.

JIRA Key: UPSISCSI-151

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-16 11:09:49 -05:00
Lalit Chandivade 28deb45cea [SCSI] qla4xxx: Fix getting BIDI CHAP for boot targets
If a boot target has a BIDI CHAP enabled, then read the user/secret from
CHAP table. Do not assume BIDI chap at peer CHAP index + 1

JIRA Key: UPSISCSI-156

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-16 11:09:32 -05:00
Lalit Chandivade 8de5b95824 [SCSI] qla4xxx: Fix exporting boot targets to sysfs
The driver failed to export primary boot target if secondary target did not
exist in the FLASH. If boot targets are not valid then driver assumed 0 and
1 as default boot targets. Since these target did not exist in flash, the
driver failed exporting all the targets.

JIRA Key: UPSISCSI-148

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-16 11:09:14 -05:00
Lalit Chandivade 4549415af6 [SCSI] qla4xxx: Do not add duplicate CHAP entry in FLASH
QLogic applications store the CHAP information in FLASH. During login,
authentication information is provided using an index into the CHAP region.

In order to support QLogic applications along with iscsiadm, updated the
LLD to not add duplicate CHAP entries in the CHAP region and preserve the
existing CHAP info in the CHAP region in FLASH.
This allows QLogic applications to pre-write the CHAP entries in the
CHAP region.

With iscsiadm, when the CHAP authentication information is sent to the LLD, the
LLD searches for the entry in CHAP region in FLASH, if exists then do not add.
If CHAP entry does not exist then add the CHAP entry in the CHAP region.

JIRA Key: UPSISCSI-146

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-16 11:08:41 -05:00
Lalit Chandivade 0854f665a1 [SCSI] qla4xxx: Fix bidirectional CHAP.
Driver was not setting the bidirectional CHAP bit correctly in
the DDB entry.

JIRA Key: UPSISCSI-108

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-16 11:08:16 -05:00
Nilesh Javali 938239560c [SCSI] qla4xxx: Add new FLT firmware region
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-16 11:06:54 -05:00
Mike Christie 9c224ac215 [SCSI] qla4xxx: select iscsi boot sysfs attrs
qla4xxx now uses iscsi_boot_sysfs to export the targets used
for boot to sysfs. It needs to select that config option
to make sure that module is also built.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-09-18 10:10:07 +04:00
Randy Dunlap d7a210f3d3 scsi: qla4xxx driver depends on NET
When CONFIG_NET is disabled, SCSI_QLA_ISCSI selects SCSI_ISCSI_ATTRS,
which uses network interfaces, so the build fails with multiple errors:

  warning: (ISCSI_TCP && SCSI_CXGB3_ISCSI && SCSI_CXGB4_ISCSI && SCSI_QLA_ISCSI && INFINIBAND_ISER) selects SCSI_ISCSI_ATTRS which has unmet direct dependencies (SCSI && NET)

  ERROR: "skb_trim" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
  ERROR: "netlink_kernel_create" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
  ERROR: "netlink_kernel_release" [drivers/scsi/scsi_transport_iscsi.ko] undefined!
  ...

so make SCSI_QLA_ISCSI also depend on NET to prevent the build errors.

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc:	Ravi Anand <ravi.anand@qlogic.com>
Cc:	Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc:	iscsi-driver@qlogic.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-09-10 17:31:31 -07:00
Mike Christie de37920b87 [SCSI] qla4xxx: export iface name
Export the name of iface session is attached to. This is needed
so tools like iscsiadm/iscsistart can match the sessions to
userspace ifaces when rebuilding iscsid's state during boot.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:54 -06:00
Vikas Chaudhary 95d31262b3 [SCSI] qla4xxx: Added support for adapter and firmware reset
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:49 -06:00
Harish Zunjarrao 6085491c34 [SCSI] qla4xxx: Added Get ACB support using BSG
This command is used to read ACB params from firmware

Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:44 -06:00
Harish Zunjarrao 5232f801bd [SCSI] qla4xxx: Added restore factory defaults support using BSG
This command will causes the firmware to update all
configurations to pre-defined factory default settings.

Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:43 -06:00
Vikas Chaudhary 2ada7fc5d4 [SCSI] qla4xxx: added support to update initiator iscsi port
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:40 -06:00
Vikas Chaudhary 91ec7cec4a [SCSI] qla4xxx: Added vendor specific sysfs attributes
Added board_id, fw_state, phy_port_cnt, phy_port_num,
iscsi_func_cnt, hba_model

Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:34 -06:00
Harish Zunjarrao 7c07d139cf [SCSI] qla4xxx: Add read/update NVRAM support for 40xx adapters using BSG
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:33 -06:00
Harish Zunjarrao 8b0402e138 [SCSI] qla4xxx: Add get ACB state support using BSG
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:32 -06:00
Harish Zunjarrao ef7830bb62 [SCSI] qla4xxx: Code cleanup for read/update flash using BSG
- Corrected return status
- Added reset active check
- Removed unused dma_map_sg calls
- Added debug prints on failure

Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:30 -06:00
Vikas Chaudhary 943c157b79 [SCSI] qla4xxx: Added support to update mtu
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:29 -06:00
Manish Rangankar 2a991c2159 [SCSI] qla4xxx: Boot from SAN support for open-iscsi
Hook qla4xxx in fw boot sysfs interface so iscsi tools
can use the info to create boot sessions.

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:27 -06:00
Manish Rangankar 0e7e85019c [SCSI] qla4xxx: Remove reduandant code after open-iscsi integration.
1. Remove device database entry (ddb) state.
2. Remove device database (DDB) list building.
                With open-iscsi integration the logins to the target devices are
        handled by the user space. So the information of target is now
        maintained in the iscsi_session object. This is handled at
        libiscsi level so there is no need to maintain a list of DDBs in
        the qla4xxx LLD.
3. qla4xxx: Remove add_device_dynamically.
                Since autologin in FW is disabled with open-iscsi integration,
        driver will never get an AEN for which driver has not requested
        a DDB index. So remove the add_device_dynamically function.
4. Remove qla4xxx_tgt_dscvr
        Since firmware autologin is disabled this function will not work.
        Now user has the ability to do the target discovery and login to
        each target individually. Firwmare will not do the login on its own.
5. Remove relogin related code
        All relogin is handled by userspace now. qla4xxx just need to
        notify userspace of a connection failure, this triggers the
        relogin.
6. Remove add_session and alloc_session
        Now qla4xxx uses iscsi_session_setup that would do the necessary
        allocations for session and ddb_entry.

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:26 -06:00
Manish Rangankar b3a271a94d [SCSI] qla4xxx: support iscsiadm session mgmt
Add scsi_transport_iscsi hooks in qla4xxx to support
iSCSI session management using iscsiadm.

This patch is based on discussion here
http://groups.google.com/group/open-iscsi/browse_thread/thread/e89fd888baf656a0#

Now users can use iscsiadm to do target discovery and do login/logout to
individual targets using the qla4xxx iSCSI class interface.

This patch leaves some dead code, but to make it easier to review
we are leaving and in the next patch we will remove that old code.

V2 - NOTE: Added code to avoid waiting for AEN during login/logout
in the driver, instead added a kernel to user event
to notify iscsid about login status. Because of this
iscsid will not get blocked.

Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:24 -06:00
Vikas Chaudhary a355943ca8 [SCSI] qla4xxx: add bsg support
This patch adds bsg support to qla4xxx.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:22 -06:00
Vikas Chaudhary 6ac73e8cb0 [SCSI] qla4xxx: Add VLAN support
Add support to set VLAN and show vlan settings in sysfs

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
[Patch updated to new defines]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:20 -06:00
Mike Christie f27fb2ef7b [SCSI] iscsi class: sysfs group is_visible callout for iscsi host attrs
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's host attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:14 -06:00
Mike Christie b78dbba005 [SCSI] iscsi class: remove iface param mask
We can replace the iface param mask with the
attr_is_visible callback.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:12 -06:00
Mike Christie 1d063c1729 [SCSI] iscsi class: sysfs group is_visible callout for session attrs
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's session attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:06 -06:00
Mike Christie 3128c6c73c [SCSI] iscsi cls: sysfs group is_visible callout for conn attrs
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and drivers to use the attribute container
sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:03 -06:00
Vikas Chaudhary ed1086e041 [SCSI] qla4xxx: added support to show multiple iface in sysfs
Add support for default ipv4 and ipv6 ifaces in qla4xxx.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Reviewed-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
[make iface creation dynamic]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:36:02 -06:00
Vikas Chaudhary 2bab08fc77 [SCSI] qla4xxx: Added new "struct ipaddress_config"
- Move all ipaddress related param to "struct ipaddress_config"
  from "struct scsi_qla_host"
- update function - qla4xxx_update_local_ip()
- Rename IPOPT_IPv4_PROTOCOL_ENABLE to IPOPT_IPV4_PROTOCOL_ENABLE

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
[update for new ISCSI_IFACE values]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:35:59 -06:00
Mike Christie d00efe3fa8 [SCSI] qla4xxx: add support for set_net_config
Allows user space (iscsiadm) to send down network configuration
parameters for LLD to set private network configuration on the iSCSI
adapters.

Based on patches from Vikas Chaudhary.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:35:58 -06:00
Linus Torvalds 426048313d Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (60 commits)
  [SCSI] lpfc 8.3.24: Extend BSG infrastructure and add link diagnostics
  [SCSI] lpfc 8.3.24: Add resource extent support
  [SCSI] lpfc 8.3.24: Add request-firmware support
  [SCSI] lpfc 8.3.24: Add SR-IOV control
  [SCSI] lpfc 8.3.24: Extended hardware support and support dump images
  [SCSI] lpfc 8.3.24: Miscellaneous Fixes and Corrections
  [SCSI] libsas: Add option for SATA soft reset
  [SCSI] libsas: check dev->gone before submitting sata i/o
  [SCSI] libsas: fix/amend device gone notification in sas_deform_port()
  [SCSI] MAINTAINERS update for SCSI (new email address)
  [SCSI] Fix Ultrastor asm snippet
  [SCSI] osst: fix warning
  [SCSI] osst: wrong index used in inner loop
  [SCSI] aic94xx: world-writable sysfs update_bios file
  [SCSI] MAINTAINERS: Add drivers/target/ entry
  [SCSI] target: Convert TASK_ATTR to scsi_tcq.h definitions
  [SCSI] target: Convert REPORT_LUNs to use int_to_scsilun
  [SCSI] target: Fix task->task_execute_queue=1 clear bug + LUN_RESET OOPs
  [SCSI] target: Fix bug with task_sg chained transport_free_dev_tasks release
  [SCSI] target: Fix interrupt context bug with stats_lock and core_tmr_alloc_req
  ...
2011-05-27 19:52:57 -07:00
Roland Dreier dbee8a0aff x86: remove 32-bit versions of readq()/writeq()
The presense of a writeq() implementation on 32-bit x86 that splits the
64-bit write into two 32-bit writes turns out to break the mpt2sas driver
(and in general is risky for drivers as was discussed in
<http://lkml.kernel.org/r/adaab6c1h7c.fsf@cisco.com>).  To fix this,
revert 2c5643b1c5 ("x86: provide readq()/writeq() on 32-bit too") and
follow-on cleanups.

This unfortunately leads to pushing non-atomic definitions of readq() and
write() to various x86-only drivers that in the meantime started using the
definitions in the x86 version of <asm/io.h>.  However as discussed
exhaustively, this is actually the right thing to do, because the right
way to split a 64-bit transaction is hardware dependent and therefore
belongs in the hardware driver (eg mpt2sas needs a spinlock to make sure
no other accesses occur in between the two halves of the access).

Build tested on 32- and 64-bit x86 allmodconfig.

Link: http://lkml.kernel.org/r/x86-32-writeq-is-broken@mdm.bga.com
Acked-by: Hitoshi Mitake <h.mitake@gmail.com>
Cc: Kashyap Desai <Kashyap.Desai@lsi.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Acked-by: James Bottomley <James.Bottomley@parallels.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-05-25 08:39:44 -07:00
Vikas Chaudhary 6b278656f2 [SCSI] qla4xxx: Update driver version to 5.02.00-k7
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-24 12:40:34 -04:00
Harish Zunjarrao 7ad633c06b [SCSI] qla4xxx: Added vendor specific sysfs attributes
Added fw_version, serial_num, iscsi version and boot loader version
sysfs attributes.

Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-24 12:40:23 -04:00
Vikas Chaudhary 8f0722cae6 [SCSI] qla4xxx: Remove host_lock in queuecommand function
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-24 12:40:12 -04:00
Lalit Chandivade 1b46807e0b [SCSI] qla4xxx: Remove AF_DPC_SCHEDULED flag from ha.
Since queue_work does not requeue, there is no need to check
if a work is in progress using the AF_DPC_SCHEDULED flag.
queue_work would return if work is pending without adding the
work, do_dpc would again get invoked from qla4xxx_timer if
there is still DPC flags set.

Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-24 12:40:02 -04:00
Vikas Chaudhary 977f46a4bb [SCSI] qla4xxx: Don't check FW alive if ISP82XX reset is in progress
Corrected logic to don't check for F/W is alive if reset is already
in progress for ISP82XX

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-24 12:39:52 -04:00
Vikas Chaudhary 0160ef1269 [SCSI] qla4xxx: Don't process mbx interrupt unconditionally
Do not process interrupt unconditionally during mailbox processing  which can
lead to spurious interrupt. Mailbox completion are now polled if interrupt are
disabled or wait for interrupt to come in if its enabled

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-24 12:39:42 -04:00
Prasanna Mumbai 6d78bd56be [SCSI] qla4xxx: Complete the cmd if sense_len is zero
Complete the cmd if sense length is zero. For cases where sense
data spans across multiple iocb's by FW, we need to hold on to the
I/O (ha->status_srb != NULL) till we have processed them all and
copied the sense data from internal buffer to scsi_cmd sense buffer.

Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-24 12:39:29 -04:00
Vikas Chaudhary 68d92ebf59 [SCSI] qla4xxx: Dump HW/FW reg to figure out what caused FW to be hung for ISP82XX
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-24 12:39:20 -04:00
Vikas Chaudhary cb74428ee3 [SCSI] qla4xxx: Updated the reset sequence for ISP82xx
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-24 12:38:57 -04:00
Prasanna Mumbai 185f107ef9 [SCSI] qla4xxx: update function qla4xxx_isr_decode_mailbox()
- Added MBOX_ASTS_DUPLICATE_IP AEN handling.
- Update MBOX_AEN_REG_COUNT to 8 so that driver will save status
  of all mbox registers in aen_q

Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-24 12:38:46 -04:00
Linus Torvalds 57d19e80f4 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
  b43: fix comment typo reqest -> request
  Haavard Skinnemoen has left Atmel
  cris: typo in mach-fs Makefile
  Kconfig: fix copy/paste-ism for dell-wmi-aio driver
  doc: timers-howto: fix a typo ("unsgined")
  perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
  md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
  treewide: fix a few typos in comments
  regulator: change debug statement be consistent with the style of the rest
  Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
  audit: acquire creds selectively to reduce atomic op overhead
  rtlwifi: don't touch with treewide double semicolon removal
  treewide: cleanup continuations and remove logging message whitespace
  ath9k_hw: don't touch with treewide double semicolon removal
  include/linux/leds-regulator.h: fix syntax in example code
  tty: fix typo in descripton of tty_termios_encode_baud_rate
  xtensa: remove obsolete BKL kernel option from defconfig
  m68k: fix comment typo 'occcured'
  arch:Kconfig.locks Remove unused config option.
  treewide: remove extra semicolons
  ...
2011-05-23 09:12:26 -07:00
Justin P. Mattock 70f23fd66b treewide: fix a few typos in comments
- kenrel -> kernel
- whetehr -> whether
- ttt -> tt
- sss -> ss

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-05-10 10:16:21 +02:00
Christoph Hellwig 5cd049a599 [SCSI] remove cmd->serial_number litter
Stop using cmd->serial_number in printks.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-05-01 10:22:40 -05:00
Lucas De Marchi 25985edced Fix common misspellings
Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-31 11:26:23 -03:00
Sarang Radke 5fa8b57313 [SCSI] qla4xxx: Use polling mode for disable interrupt mailbox completion
Disable Interrupt MBX completion will disable the interrupt on
successful completion.  Fixed the bug where driver was waiting for
Interrupt to come in for its completion.  Now driver will poll for
disable interrupt MBX completion.

Signed-off-by: Sarang Radke <sarang.radke@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-03-23 12:53:09 -05:00
Vikas Chaudhary 2dcb0a6104 [SCSI] qla4xxx: Update driver version to 5.02.00-k6
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-03-23 12:53:05 -05:00
Prasanna Mumbai d32cee3c2d [SCSI] qla4xxx: masking required bits of add_fw_options during initialization
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-03-23 12:53:04 -05:00
Vikas Chaudhary 2d7924e6be [SCSI] qla4xxx: added new function qla4xxx_relogin_all_devices
Move relogin to all devices code from do_dpc to new
fuction qla4xxx_relogin_all_devices()

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-03-23 12:53:04 -05:00
Vikas Chaudhary 3038727c83 [SCSI] qla4xxx: add support for ql4xsess_recovery_tmo cmd line param
Target Session Recovery Timeout

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-03-23 12:53:03 -05:00
Vikas Chaudhary 8bb4033d2b [SCSI] qla4xxx: Add support for ql4xmaxqdepth command line parameter
This provides the flexibility to modify the qdepth based on different
target devices to make the best use of system resources.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-03-23 12:53:02 -05:00
Vikas Chaudhary fc7657c9d9 [SCSI] qla4xxx: cleanup function qla4xxx_process_ddb_changed
We don't need to check ddb old state we can take action
based on ddb new state.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-03-23 12:53:01 -05:00
Karen Higgins 7eece5a084 [SCSI] qla4xxx: Prevent other port reinitialization during remove_adapter
remove ha flag AF_HBA_GOING_AWAY and added flag AF_HA_REMOVAL
to mark the other ISP-4xxx port to indicate that the driver is
being removed, so that the other port will not re-initialize
while in the process of removing the ha due to driver unload
or hba hotplug.

Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-03-23 12:53:01 -05:00
Vikas Chaudhary 58da51dcfc [SCSI] qla4xxx: remove unused ddb flag DF_NO_RELOGIN
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-03-23 12:53:00 -05:00
Karen Higgins 7edd9a7b28 [SCSI] qla4xxx: cleanup DDB relogin logic during initialization
Driver has capability to add device dynamically and present
them to OS, driver no longer need to wait for DDBs to come
online during driver initialization.
Driver still issues a relogin for DDBs that are not online,
but no longer wait for DDB to come online.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-03-23 12:52:59 -05:00
Prasanna Mumbai f9880e76fd [SCSI] qla4xxx: Do not retry ISP82XX initialization if H/W state is failed
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-03-23 12:48:33 -05:00
Prasanna Mumbai 99b53bf50c [SCSI] qla4xxx: Do not send mbox command if FW is in failed state
FW is not able to process mbox command if FW state is failed. This will cause
mbox command to timeout and adapter reset. We have separate function to detect
FW failed state and do adapter reset. So to avoid mbox command timeout, do not
process mbox command in case of FW state failed.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-03-23 12:48:31 -05:00
Vikas Chaudhary 9640de2099 [SCSI] qla4xxx: cleanup qla4xxx_initialize_ddb_list()
Remove process all aen code from qla4xxx_initialize_ddb_list()
as DPC activities should be done in DPC only.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2011-03-23 12:48:26 -05:00
Justin P. Mattock cd09b2c3d0 drivers:scsi Change printk typo initate -> initiate
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-02-17 17:42:17 +01:00
Vikas Chaudhary 6b57b15970 [SCSI] qla4xxx: Update driver version to 5.02.00-k5
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-12-21 12:24:44 -06:00
Vikas Chaudhary 7d01d0698f [SCSI] qla4xxx: Updated the Copyright header
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-12-21 12:24:43 -06:00
Vikas Chaudhary 3930b8c1f3 [SCSI] qla4xxx: do not reset hba if ql4xdontresethba is set
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-12-21 12:24:43 -06:00
Lalit Chandivade d56a1f7b39 [SCSI] qla4xxx: do not check for fw hung if reset retry is in progress
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-12-21 12:24:42 -06:00
Prasanna Mumbai e128271b7b [SCSI] qla4xxx: cache new IP address acquired via DHCP
Prior to firmware state change from ACQUIRING to READY, an
0x8029 AEN is received. Added code to check previous state
being ACQUIRING in order to update the ip address in the driver.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-12-21 12:24:41 -06:00
Lalit Chandivade 4cd83cbef8 [SCSI] qla4xxx: Fail initialization if qla4_8xxx_pci_mem_write_2M fails
Since if fw load is failing, running on incomplete fw load would
be fatal.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-12-21 12:24:41 -06:00
Lalit Chandivade fe998527e3 [SCSI] qla4xxx: put device in FAILED state for 82XX initialization failure
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-12-21 12:24:40 -06:00
Lalit Chandivade e6b07df8b0 [SCSI] qla4xxx: do not process interrupt unconditionally
in mailbox command do not process interrupt unconditionally,
process interrupt only in polling mode

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-12-21 12:24:38 -06:00
Karen Higgins 6790d4fecf [SCSI] qla4xxx: use correct fw_ddb_index in abort task
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-12-21 12:24:37 -06:00
Swapnil Nagle a1fc26baae [SCSI] qla4xxx: memory wedge with peg_halt test in loop
Signed-off-by: Swapnil Nagle <swapnil.nagle@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-12-21 12:24:36 -06:00
Shyam Sundar 61391d314e [SCSI] qla4xxx: initialize MSI in correct way
IRQF_SHARED flag should not be set when calling request_irq for MSI since
this interrupt mechanism cannot be shared like standard INTx

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-12-21 12:24:35 -06:00
Vikas Chaudhary 3e1350c4dc [SCSI] qla4xxx: Drop use of IRQF_DISABLE
IRQF_DISABLE flag is deprecated and this flag is a NOOP in kernel.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-12-21 12:24:35 -06:00
Jeff Garzik f281233d3e SCSI host lock push-down
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.

The patch below presents a simple SCSI host lock push-down as an
equivalent transformation.  No locking or other behavior should change
with this patch.  All existing bugs and locking orders are preserved.

Additionally, add one parameter to queuecommand,
	struct Scsi_Host *
and remove one parameter from queuecommand,
	void (*done)(struct scsi_cmnd *)

Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.

Minimal code disturbance was attempted with this change.  Most drivers
needed only two one-line modifications for their host lock push-down.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-11-16 13:33:23 -08:00
Mike Christie a1e0063d0c [SCSI] qla4xxx: Fix cmd check in qla4xxx_cmd_wait
If the command has timedout then the block layer has called
blk_mark_rq_complete. If qla4xxx_cmd_wait is then called
from qla4xxx_eh_host_reset, we will always fail, because if
the driver calls scsi_done then the the block layer will fail
at blk_complete_request's blk_mark_rq_complete call instead of
calling the normal completion path including the function,
blk_queue_end_tag, which releases the tag.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-26 11:16:56 -05:00
Vikas Chaudhary 349ed5a060 [SCSI] qla4xxx: Update driver version to 5.02.00-k4
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-25 14:56:04 -05:00
Mike Christie 92b3e5bbbe [SCSI] qla4xxx: grab hardware_lock in eh_abort before accessing srb
grab hardware_lock in eh_abort before accessing srb to avoid
race between command completion and get refcount on srb.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-25 14:55:57 -05:00
Vikas Chaudhary d64eab764a [SCSI] qla4xxx: remove unwanted check for bad spd
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-25 14:54:16 -05:00
Vikas Chaudhary 7b3595df0e [SCSI] qla4xxx: update AER support for ISP82XX
* Cleanup qla4xxx_pci_mmio_enabled():
  don't want to return PCI_ERS_NEED_RESET if firmware hung.
  IDC will take care of it.
* Request irq after initialize_adapter() in qla82xx_error_recovery().
* Return all active commands from qla4xxx_pci_error_detected().
* Cleanup ql4_def.h

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-25 14:53:42 -05:00
Shyam Sundar b25ee66f2d [SCSI] qla4xxx: Clear the rom lock if the firmware died while holding it.
There is a possibility that the firmware dies while the rom
lock is held. The only way to recover from this condition is
to forcefully unlock.

Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-25 14:53:29 -05:00
Shyam Sundar 2657c800db [SCSI] qla4xxx: use CRB Register for Request Queue in-pointer
Switching from doorbell mechanism to CRB register based

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-25 14:52:44 -05:00
Karen Higgins 91a772a4b1 [SCSI] qla4xxx: dump mailbox registers on System Error
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-25 14:52:03 -05:00
Shyam Sundar 6434080b12 [SCSI] qla4xxx: Add support for 8130/8131 AENs.
AEN 8130 Corresponds to an event representing the insertion (detection)
of a transceiver. It also reports the type of the SFP+.
AEN 8131 corresponds to the removal of a transceiver.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-25 14:51:23 -05:00
Lalit Chandivade 99457d75f6 [SCSI] qla4xxx: Reset seconds_since_last_heartbeat correctly.
The seconds_since_last_heartbeat should be checked for consecutive
heartbeat checks. Currently it could happen that it gets set to
max (2 seconds) for non-consecutive heartbeat checks.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-25 14:51:04 -05:00
Nilesh Javali 2bd1e2be8f [SCSI] qla4xxx: On firmware hang do not wait for the outstanding commands to complete
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-25 14:50:38 -05:00
Vikas Chaudhary 3710c60c09 [SCSI] qla4xxx: free_irqs on failed initialize_adapter
Since interrupts are registered in start_firmware(load_risc) for 82xx,
free them if init_firmware fails.

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-25 14:50:08 -05:00
Vikas Chaudhary 735e41543c [SCSI] qla4xxx: correct data type of sense_len in qla4xxx_status_cont_entry
change data type of sense_len from uint8_t to uint16_t

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2010-10-25 14:49:40 -05:00