Current driver version is able to handle only one bridge at time.
Configuring two bridges on two different ports would end up shorting this
bridges by HW. To reproduce it:
ip l a name br0 type bridge
ip l a name br1 type bridge
ip l s dev br0 up
ip l s dev br1 up
ip l s lan1 master br0
ip l s dev lan1 up
ip l s lan2 master br1
ip l s dev lan2 up
Ping on lan1 and get response on lan2, which should not happen.
This happened, because current driver version is storing one global "Port VLAN
Membership" and applying it to all ports which are members of any
bridge.
To solve this issue, we need to handle each port separately.
This patch is dropping the global port member storage and calculating
membership dynamically depending on STP state and bridge participation.
Note: STP support was broken before this patch and should be fixed
separately.
Fixes: c2e866911e ("net: dsa: microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20211126123926.2981028-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the ksz module is installed and removed using rmmod, kernel crashes
with null pointer dereferrence error. During rmmod, ksz_switch_remove
function tries to cancel the mib_read_workqueue using
cancel_delayed_work_sync routine and unregister switch from dsa.
During dsa_unregister_switch it calls ksz_mac_link_down, which in turn
reschedules the workqueue since mib_interval is non-zero.
Due to which queue executed after mib_interval and it tries to access
dp->slave. But the slave is unregistered in the ksz_switch_remove
function. Hence kernel crashes.
To avoid this crash, before canceling the workqueue, resetted the
mib_interval to 0.
v1 -> v2:
-Removed the if condition in ksz_mib_read_work
Fixes: 469b390e1b ("net: dsa: microchip: use delayed_work instead of timer + work")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2f1e8ea726 ("net: dsa: link interfaces with the DSA
master to get rid of lockdep warnings"), DSA gained a requirement which
it did not fulfill, which is to unlink itself from the DSA master at
shutdown time.
Since the Microchip sub-driver for KSZ8863 was introduced after the bad
commit, it has never worked with DSA masters which decide to unregister
their net_device on shutdown, effectively hanging the reboot process.
To fix that, we need to call dsa_switch_shutdown.
Since this driver expects the MDIO bus to be backed by mdio_bitbang, I
don't think there is currently any MDIO bus driver which implements its
->shutdown by redirecting it to ->remove, but in any case, to be
compatible with that pattern, it is necessary to implement an "if this
then not that" scheme, to avoid ->remove and ->shutdown from being
called both for the same struct device.
Fixes: 60a3647600 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support")
Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lino reports that on his system with bcmgenet as DSA master and KSZ9897
as a switch, rebooting or shutting down never works properly.
What does the bcmgenet driver have special to trigger this, that other
DSA masters do not? It has an implementation of ->shutdown which simply
calls its ->remove implementation. Otherwise said, it unregisters its
network interface on shutdown.
This message can be seen in a loop, and it hangs the reboot process there:
unregister_netdevice: waiting for eth0 to become free. Usage count = 3
So why 3?
A usage count of 1 is normal for a registered network interface, and any
virtual interface which links itself as an upper of that will increment
it via dev_hold. In the case of DSA, this is the call path:
dsa_slave_create
-> netdev_upper_dev_link
-> __netdev_upper_dev_link
-> __netdev_adjacent_dev_insert
-> dev_hold
So a DSA switch with 3 interfaces will result in a usage count elevated
by two, and netdev_wait_allrefs will wait until they have gone away.
Other stacked interfaces, like VLAN, watch NETDEV_UNREGISTER events and
delete themselves, but DSA cannot just vanish and go poof, at most it
can unbind itself from the switch devices, but that must happen strictly
earlier compared to when the DSA master unregisters its net_device, so
reacting on the NETDEV_UNREGISTER event is way too late.
It seems that it is a pretty established pattern to have a driver's
->shutdown hook redirect to its ->remove hook, so the same code is
executed regardless of whether the driver is unbound from the device, or
the system is just shutting down. As Florian puts it, it is quite a big
hammer for bcmgenet to unregister its net_device during shutdown, but
having a common code path with the driver unbind helps ensure it is well
tested.
So DSA, for better or for worse, has to live with that and engage in an
arms race of implementing the ->shutdown hook too, from all individual
drivers, and do something sane when paired with masters that unregister
their net_device there. The only sane thing to do, of course, is to
unlink from the master.
However, complications arise really quickly.
The pattern of redirecting ->shutdown to ->remove is not unique to
bcmgenet or even to net_device drivers. In fact, SPI controllers do it
too (see dspi_shutdown -> dspi_remove), and presumably, I2C controllers
and MDIO controllers do it too (this is something I have not researched
too deeply, but even if this is not the case today, it is certainly
plausible to happen in the future, and must be taken into consideration).
Since DSA switches might be SPI devices, I2C devices, MDIO devices, the
insane implication is that for the exact same DSA switch device, we
might have both ->shutdown and ->remove getting called.
So we need to do something with that insane environment. The pattern
I've come up with is "if this, then not that", so if either ->shutdown
or ->remove gets called, we set the device's drvdata to NULL, and in the
other hook, we check whether the drvdata is NULL and just do nothing.
This is probably not necessary for platform devices, just for devices on
buses, but I would really insist for consistency among drivers, because
when code is copy-pasted, it is not always copy-pasted from the best
sources.
So depending on whether the DSA switch's ->remove or ->shutdown will get
called first, we cannot really guarantee even for the same driver if
rebooting will result in the same code path on all platforms. But
nonetheless, we need to do something minimally reasonable on ->shutdown
too to fix the bug. Of course, the ->remove will do more (a full
teardown of the tree, with all data structures freed, and this is why
the bug was not caught for so long). The new ->shutdown method is kept
separate from dsa_unregister_switch not because we couldn't have
unregistered the switch, but simply in the interest of doing something
quick and to the point.
The big question is: does the DSA switch's ->shutdown get called earlier
than the DSA master's ->shutdown? If not, there is still a risk that we
might still trigger the WARN_ON in unregister_netdevice that says we are
attempting to unregister a net_device which has uppers. That's no good.
Although the reference to the master net_device won't physically go away
even if DSA's ->shutdown comes afterwards, remember we have a dev_hold
on it.
The answer to that question lies in this comment above device_link_add:
* A side effect of the link creation is re-ordering of dpm_list and the
* devices_kset list by moving the consumer device and all devices depending
* on it to the ends of these lists (that does not happen to devices that have
* not been registered when this function is called).
so the fact that DSA uses device_link_add towards its master is not
exactly for nothing. device_shutdown() walks devices_kset from the back,
so this is our guarantee that DSA's shutdown happens before the master's
shutdown.
Fixes: 2f1e8ea726 ("net: dsa: link interfaces with the DSA master to get rid of lockdep warnings")
Link: https://lore.kernel.org/netdev/20210909095324.12978-1-LinoSanfilippo@gmx.de/
Reported-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The magic number 4 in VLAN table lookup was the number of entries we
can read and write at once. Using phy_port_cnt here doesn't make
sense and presumably broke VLAN filtering for 3-port switches. Change
it back to 4.
Fixes: 4ce2a984ab ("net: dsa: microchip: ksz8795: use phy_port_cnt ...")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ksz8_port_vlan_filtering() sets or clears the VLAN Enable
hardware flag. That controls discarding of packets with a VID that
has not been enabled for any port on the switch.
Since it is a global flag, set the dsa_switch::vlan_filtering_is_global
flag so that the DSA core understands this can't be controlled per
port.
When VLAN filtering is enabled, the switch should also discard packets
with a VID that's not enabled on the ingress port. Set or clear each
external port's VLAN Ingress Filter flag in ksz8_port_vlan_filtering()
to make that happen.
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the CPU port, we can support both tagged and untagged VLANs at the
same time by doing any necessary untagging in software rather than
hardware. To enable that, keep the CPU port's Remove Tag flag cleared
and set the dsa_switch::untag_bridge_pvid flag.
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN is deleted from a port, the flags in struct
switchdev_obj_port_vlan are always 0. ksz8_port_vlan_del() copies the
BRIDGE_VLAN_INFO_UNTAGGED flag to the port's Tag Removal flag, and
therefore always clears it.
In case there are multiple VLANs configured as untagged on this port -
which seems useless, but is allowed - deleting one of them changes the
remaining VLANs to be tagged.
It's only ever necessary to change this flag when a VLAN is added to
the port, so leave it unchanged in ksz8_port_vlan_del().
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switches supported by ksz8795 only have a per-port flag for Tag
Removal. This means it is not possible to support both tagged and
untagged VLANs on the same port. Reject attempts to add a VLAN that
requires the flag to be changed, unless there are no VLANs currently
configured.
VID 0 is excluded from this check since it is untagged regardless of
the state of the flag.
On the CPU port we could support tagged and untagged VLANs at the same
time. This will be enabled by a later patch.
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz8795 has never actually enabled PVID tag insertion, and it also
programmed the PVID incorrectly. To fix this:
* Allow tag insertion to be controlled per ingress port. On most
chips, set bit 2 in Global Control 19. On KSZ88x3 this control
flag doesn't exist.
* When adding a PVID:
- Set the appropriate register bits to enable tag insertion on
egress at every other port if this was the packet's ingress port.
- Mask *out* the VID from the default tag, before or-ing in the new
PVID.
* When removing a PVID:
- Clear the same control bits to disable tag insertion.
- Don't update the default tag. This wasn't doing anything useful.
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz_read64() currently does some dubious byte-swapping on the two
halves of a 64-bit register, and then only returns the high bits.
Replace this with a straightforward expression.
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Ben Hutchings <ben.hutchings@mind.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
For_each_available_child_of_node should have of_node_put() before
return around line 423.
Generated by: scripts/coccinelle/iterators/for_each_child.cocci
CC: Alexander Lobakin <alobakin@pm.me>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch support for cable test for the ksz886x switches and the
ksz8081 PHY.
The patch was tested on a KSZ8873RLL switch with following results:
- port 1:
- provides invalid values, thus return -ENOTSUPP
(Errata: DS80000830A: "LinkMD does not work on Port 1",
http://ww1.microchip.com/downloads/en/DeviceDoc/KSZ8873-Errata-DS80000830A.pdf)
- port 2:
- can detect distance
- can detect open on each wire of pair A (wire 1 and 2)
- can detect open only on one wire of pair B (only wire 3)
- can detect short between wires of a pair (wires 1 + 2 or 3 + 6)
- short between pairs is detected as open.
For example short between wires 2 + 3 is detected as open.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mapping for LINK_MD register to enable cable testing functionality.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for MDI-X status and configuration
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the phylink support to the ksz8795 driver to provide
configuration exceptions on quirky KSZ8863 and KSZ8873 ports.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some micrel devices share the same PHY register defines. This patch
moves them to one common header so other drivers can reuse them.
And reuse generic MII_* defines where possible.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also enable phy errata workaround on 9567 since has the same errata as
the 9477 according to the manufacture's documentation.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz_switch_alloc() will return NULL only if allocation is failed. So,
the proper return value is -ENOMEM.
Fixes: 60a3647600 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix possible NULL pointer dereference in case devm_kzalloc() failed to
allocate memory
Fixes: cc13e52c3a ("net: dsa: microchip: Add Microchip KSZ8863 SPI based driver support")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix possible NULL pointer dereference in case devm_kzalloc() failed to
allocate memory.
Fixes: 60a3647600 ("net: dsa: microchip: Add Microchip KSZ8863 SMI based driver support")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the for-loop in ksz8_port_init_cnt is causing a static
analysis infinite loop warning with the comparison of
mib->cnt_ptr < dev->reg_mib_cnt. This occurs because mib->cnt_ptr
is a u8 and dev->reg_mib_cnt is an int and the analyzer determines
that mib->cnt_ptr potentially can wrap around to zero if the value
in dev->reg_mib_cnt is > 255. However, this value is never this
large, it is always less than 256 so make reg_mib_cnt a u8.
Addresses-Coverity: ("Infinite loop")
Fixes: e66f840c08 ("net: dsa: ksz: Add Microchip KSZ8795 DSA driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210428120010.337959-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add KSZ88X3 driver support. We add support for the KXZ88X3 three port
switches using the Microchip SMI Interface. They are supported using the
MDIO-Bitbang Interface.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add KSZ88X3 driver support. We add support for the KXZ88X3 three port
switches using the SPI Interface.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add support for the ksz8863 and ksz8873 chips which are
using the same register patterns but other offsets as the
ksz8795.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to get this driver used with other switches the functions need
to use different offsets and register shifts. This patch changes the
direct use of the register defines to register description structures,
which can be set depending on the chips register layout.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the cpu interface selection code to a individual
function specific for ksz8795. It will make it simpler to customize the
code path for different switches supported by this driver.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can be used on other chips of this type. To reflect
this we rename the drivers prefix from ksz8795 to ksz8.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers can't dynamically change the VLAN filtering option, or
impose some restrictions, it would be nice to propagate this info
through netlink instead of printing it to a kernel log that might never
be read. Also netlink extack includes the module that emitted the
message, which means that it's easier to figure out which ones are
driver-generated errors as opposed to command misuse.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow drivers to communicate their restrictions to user space directly,
instead of printing to the kernel log. Where the conversion would have
been lossy and things like VLAN ID could no longer be conveyed (due to
the lack of support for printf format specifier in netlink extack), I
chose to keep the messages in full form to the kernel log only, and
leave it up to individual driver maintainers to move more messages to
extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/can/dev.c
b552766c87 ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec9 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c4 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf2287 ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5a ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
KSZ8794CNX datasheet section 8.0 RESET CIRCUIT describes recommended
circuit for interfacing with CPU/FPGA reset consisting of 10k pullup
resistor and 10uF capacitor to ground. This circuit takes ~100 ms to
rise enough to release the reset.
For maximum supply voltage VDDIO=3.3V VIH=2.0V R=10kR C=10uF that is
VDDIO - VIH
t = R * C * -ln( ------------- ) = 10000*0.00001*-(-0.93)=0.093 s
VDDIO
so we need ~95 ms for the reset to really de-assert, and then the
original 100us for the switch itself to come out of reset. Simply
msleep() for 100 ms which fits the constraint with a bit of extra
space.
Fixes: 5b79798090 ("net: dsa: microchip: Implement recommended reset timing")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Paul Barker <pbarker@konsulko.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210120030502.617185-1-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The KSZ8795 switch has 4 external ports {0,1,2,3} and 1 CPU port {4}, so
does the KSZ8765. The KSZ8794 seems to be repackaged KSZ8795 with different
ID and port 3 not routed out, however the port 3 registers are present in
the silicon, so the KSZ8794 switch has 3 external ports {0,1,2} and 1 CPU
port {4}. Currently the driver always uses the last port as CPU port, on
KSZ8795/KSZ8765 that is port 4 and that is OK, but on KSZ8794 that is port
3 and that is not OK, as it must also be port 4.
This patch adjusts the driver such that it always registers a switch with
5 ports total (4 external ports, 1 CPU port), always sets the CPU port to
switch port 4, and then configures the external port mask according to
the switch model -- 3 ports for KSZ8794 and 4 for KSZ8795/KSZ8765.
Fixes: 68a1b676db ("net: dsa: microchip: ksz8795: remove superfluous port_cnt assignment")
Fixes: 4ce2a984ab ("net: dsa: microchip: ksz8795: use phy_port_cnt where possible")
Fixes: 241ed719bc ("net: dsa: microchip: ksz8795: use port_cnt instead of TOTOAL_PORT_NUM")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210120001045.488506-1-marex@denx.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in commit 54a0ed0df4 ("net: dsa: provide an option for
drivers to always receive bridge VLANs"), DSA has historically been
skipping VLAN switchdev operations when the bridge wasn't in
vlan_filtering mode, but the reason why it was doing that has never been
clear. So the configure_vlan_while_not_filtering option is there merely
to preserve functionality for existing drivers. It isn't some behavior
that drivers should opt into. Ideally, when all drivers leave this flag
set, we can delete the dsa_port_skip_vlan_configuration() function.
New drivers always seem to omit setting this flag, for some reason. So
let's reverse the logic: the DSA core sets it by default to true before
the .setup() callback, and legacy drivers can turn it off. This way, new
drivers get the new behavior by default, unless they explicitly set the
flag to false, which is more obvious during review.
Remove the assignment from drivers which were setting it to true, and
add the assignment to false for the drivers that didn't previously have
it. This way, it should be easier to see how many we have left.
The following drivers: lan9303, mv88e6060 were skipped from setting this
flag to false, because they didn't have any VLAN offload ops in the
first place.
The Broadcom Starfighter 2 driver calls the common b53_switch_alloc and
therefore also inherits the configure_vlan_while_not_filtering=true
behavior.
Also, print a message through netlink extack every time a VLAN has been
skipped. This is mildly annoying on purpose, so that (a) it is at least
clear that VLANs are being skipped - the legacy behavior in itself is
confusing, and the extack should be much more difficult to miss, unlike
kernel logs - and (b) people have one more incentive to convert to the
new behavior.
No behavior change except for the added prints is intended at this time.
$ ip link add br0 type bridge vlan_filtering 0
$ ip link set sw0p2 master br0
[ 60.315148] br0: port 1(sw0p2) entered blocking state
[ 60.320350] br0: port 1(sw0p2) entered disabled state
[ 60.327839] device sw0p2 entered promiscuous mode
[ 60.334905] br0: port 1(sw0p2) entered blocking state
[ 60.340142] br0: port 1(sw0p2) entered forwarding state
Warning: dsa_core: skipping configuration of VLAN. # This was the pvid
$ bridge vlan add dev sw0p2 vid 100
Warning: dsa_core: skipping configuration of VLAN.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210115231919.43834-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It should be the driver's business to logically separate its VLAN
offloading into a preparation and a commit phase, and some drivers don't
need / can't do this.
So remove the transactional shim from DSA and let drivers propagate
errors directly from the .port_vlan_add callback.
It would appear that the code has worse error handling now than it had
before. DSA is the only in-kernel user of switchdev that offloads one
switchdev object to more than one port: for every VLAN object offloaded
to a user port, that VLAN is also offloaded to the CPU port. So the
"prepare for user port -> check for errors -> prepare for CPU port ->
check for errors -> commit for user port -> commit for CPU port"
sequence appears to make more sense than the one we are using now:
"offload to user port -> check for errors -> offload to CPU port ->
check for errors", but it is really a compromise. In the new way, we can
catch errors from the commit phase that we previously had to ignore.
But we have our hands tied and cannot do any rollback now: if we add a
VLAN on the CPU port and it fails, we can't do the rollback by simply
deleting it from the user port, because the switchdev API is not so nice
with us: it could have simply been there already, even with the same
flags. So we don't even attempt to rollback anything on addition error,
just leave whatever VLANs managed to get offloaded right where they are.
This should not be a problem at all in practice.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For many drivers, the .port_mdb_prepare callback was not a good opportunity
to avoid any error condition, and they would suppress errors found during
the actual commit phase.
Where a logical separation between the prepare and the commit phase
existed, the function that used to implement the .port_mdb_prepare
callback still exists, but now it is called directly from .port_mdb_add,
which was modified to return an int code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Wallei <linus.walleij@linaro.org> # RTL8366
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the introduction of the switchdev API, port attributes were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceff ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
attribute notifier structures, and converts drivers to not look at this
member.
In part, this patch contains a revert of my previous commit 2e554a7a5d
("net: dsa: propagate switchdev vlan_filtering prepare phase to
drivers").
For the most part, the conversion was trivial except for:
- Rocker's world implementation based on Broadcom OF-DPA had an odd
implementation of ofdpa_port_attr_bridge_flags_set. The conversion was
done mechanically, by pasting the implementation twice, then only
keeping the code that would get executed during prepare phase on top,
then only keeping the code that gets executed during the commit phase
on bottom, then simplifying the resulting code until this was obtained.
- DSA's offloading of STP state, bridge flags, VLAN filtering and
multicast router could be converted right away. But the ageing time
could not, so a shim was introduced and this was left for a further
commit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> # RTL8366RB
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The call path of a switchdev VLAN addition to the bridge looks something
like this today:
nbp_vlan_init
| __br_vlan_set_default_pvid
| | |
| | br_afspec |
| | | |
| | v |
| | br_process_vlan_info |
| | | |
| | v |
| | br_vlan_info |
| | / \ /
| | / \ /
| | / \ /
| | / \ /
v v v v v
nbp_vlan_add br_vlan_add ------+
| ^ ^ | |
| / | | |
| / / / |
\ br_vlan_get_master/ / v
\ ^ / / br_vlan_add_existing
\ | / / |
\ | / / /
\ | / / /
\ | / / /
\ | / / /
v | | v /
__vlan_add /
/ | /
/ | /
v | /
__vlan_vid_add | /
\ | /
v v v
br_switchdev_port_vlan_add
The ranges UAPI was introduced to the bridge in commit bdced7ef78
("bridge: support for multiple vlans and vlan ranges in setlink and
dellink requests") (Jan 10 2015). But the VLAN ranges (parsed in br_afspec)
have always been passed one by one, through struct bridge_vlan_info
tmp_vinfo, to br_vlan_info. So the range never went too far in depth.
Then Scott Feldman introduced the switchdev_port_bridge_setlink function
in commit 47f8328bb1 ("switchdev: add new switchdev bridge setlink").
That marked the introduction of the SWITCHDEV_OBJ_PORT_VLAN, which made
full use of the range. But switchdev_port_bridge_setlink was called like
this:
br_setlink
-> br_afspec
-> switchdev_port_bridge_setlink
Basically, the switchdev and the bridge code were not tightly integrated.
Then commit 41c498b935 ("bridge: restore br_setlink back to original")
came, and switchdev drivers were required to implement
.ndo_bridge_setlink = switchdev_port_bridge_setlink for a while.
In the meantime, commits such as 0944d6b5a2 ("bridge: try switchdev op
first in __vlan_vid_add/del") finally made switchdev penetrate the
br_vlan_info() barrier and start to develop the call path we have today.
But remember, br_vlan_info() still receives VLANs one by one.
Then Arkadi Sharshevsky refactored the switchdev API in 2017 in commit
29ab586c3d ("net: switchdev: Remove bridge bypass support from
switchdev") so that drivers would not implement .ndo_bridge_setlink any
longer. The switchdev_port_bridge_setlink also got deleted.
This refactoring removed the parallel bridge_setlink implementation from
switchdev, and left the only switchdev VLAN objects to be the ones
offloaded from __vlan_vid_add (basically RX filtering) and __vlan_add
(the latter coming from commit 9c86ce2c1a ("net: bridge: Notify about
bridge VLANs")).
That is to say, today the switchdev VLAN object ranges are not used in
the kernel. Refactoring the above call path is a bit complicated, when
the bridge VLAN call path is already a bit complicated.
Let's go off and finish the job of commit 29ab586c3d by deleting the
bogus iteration through the VLAN ranges from the drivers. Some aspects
of this feature never made too much sense in the first place. For
example, what is a range of VLANs all having the BRIDGE_VLAN_INFO_PVID
flag supposed to mean, when a port can obviously have a single pvid?
This particular configuration _is_ denied as of commit 6623c60dc2
("bridge: vlan: enforce no pvid flag in vlan ranges"), but from an API
perspective, the driver still has to play pretend, and only offload the
vlan->vid_end as pvid. And the addition of a switchdev VLAN object can
modify the flags of another, completely unrelated, switchdev VLAN
object! (a VLAN that is PVID will invalidate the PVID flag from whatever
other VLAN had previously been offloaded with switchdev and had that
flag. Yet switchdev never notifies about that change, drivers are
supposed to guess).
Nonetheless, having a VLAN range in the API makes error handling look
scarier than it really is - unwinding on errors and all of that.
When in reality, no one really calls this API with more than one VLAN.
It is all unnecessary complexity.
And despite appearing pretentious (two-phase transactional model and
all), the switchdev API is really sloppy because the VLAN addition and
removal operations are not paired with one another (you can add a VLAN
100 times and delete it just once). The bridge notifies through
switchdev of a VLAN addition not only when the flags of an existing VLAN
change, but also when nothing changes. There are switchdev drivers out
there who don't like adding a VLAN that has already been added, and
those checks don't really belong at driver level. But the fact that the
API contains ranges is yet another factor that prevents this from being
addressed in the future.
Of the existing switchdev pieces of hardware, it appears that only
Mellanox Spectrum supports offloading more than one VLAN at a time,
through mlxsw_sp_port_vlan_set. I have kept that code internal to the
driver, because there is some more bookkeeping that makes use of it, but
I deleted it from the switchdev API. But since the switchdev support for
ranges has already been de facto deleted by a Mellanox employee and
nobody noticed for 4 years, I'm going to assume it's not a biggie.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com> # switchdev and mlxsw
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The value of the define VLAN_TABLE_ENTRIES can be derived from
num_vlans. This patch is using the variable num_vlans instead and
removes the extra define.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To get the driver working with other chips using different port counts
the dyn_mac_table should be flushed depending on the amount of available
ports. This patch remove the extra define TOTOAL_PORT_NUM and is
making use of the dynamic port_cnt variable instead.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable mib_port_cnt has the same meaning as port_cnt.
This driver removes the extra variable and is using port_cnt
everywhere instead.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ksz8795 driver is using port_cnt differently to the other microchip
DSA drivers. It sets it to the external physical port count, than the
whole port count (including the cpu port). This patch is aligning the
variables purpose with the other microchip drivers.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable num_ports is already assigned in the init function. The
drivers individual init function already handles the different purpose
of port_cnt vs port_cnt + 1. This patch removes the extra assignment of
the variable.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver is currently hard coded to SWITCH_PORT_NUM being
(TOTAL_PORT_NUM - 1) which is limited to 4 user ports for the ksz8795.
The phy_port_cnt is referring to its user ports. The patch removes the
extra define and use the assigned variable phy_port_cnt instead so the
driver can be used on different switches.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable mib_cnt is assigned with TOTAL_SWITCH_COUNTER_NUM. This
value can also be derived from the array size of mib_names. This patch
uses this calculated value instead, removes the extra define and uses
mib_cnt everywhere possible instead of the static define
TOTAL_SWITCH_COUNTER_NUM. Keeping it in a separate variable instead of
using ARRAY_SIZE everywhere instead makes the driver more flexible for
future use of devices with different amount of counters.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The extra define SWITCH_COUNTER_NUM is a copy of the KSZ8795_COUNTER_NUM
define. This patch initializes reg_mib_cnt with KSZ8795_COUNTER_NUM,
makes use of reg_mib_cnt everywhere instead and removes the extra
define.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch moves all variable assignments to the init function. It
leaves the detect function for its single purpose to detect which chip
version is found.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The port_cnt assignment will be done again in the init function.
This patch removes the previous assignment in the detect function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The variable last_port is not used anywhere, this patch removes it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Oleksij Rempel
Sean Anderson
Arun Ramadoss
Vladimir Oltean
Ben Hutchings
kernel test robot
Oleksij Rempel
Michael Grzeschik
George McCollister
Colin Ian King
Jakub Kicinski
Marek Vasut
Vladimir Oltean