Just like PKTINFO, limit the options area to 64K.
Based upon report by Eric Sesterhenn and analysis by
Roland Dreier.
Signed-off-by: David S. Miller <davem@davemloft.net>
As the options passed to ip6_append_data may be ephemeral, we need
to duplicate it for corking. This patch applies the simplest fix
which is to memdup all the relevant bits.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ip6mr.c: In function 'pim6_rcv':
net/ipv6/ip6mr.c:368: error: implicit declaration of function 'csum_ipv6_magic'
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately simplicity isn't always the best. The fraginfo
interface turned out to be suboptimal. The problem was quite
obvious. For every packet, we have to copy the headers from
the frags structure into skb->head, even though for 99% of the
packets this part is immediately thrown away after the merge.
LRO didn't have this problem because it directly read the headers
from the frags structure.
This patch attempts to address this by creating an interface
that allows GRO to access the headers in the first frag without
having to copy it. Because all drivers that use frags place the
headers in the first frag this optimisation should be enough.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel manages this value internally, as necessary, as
VIFs are added/removed and as multicast routers are registered
and deregistered.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses the IPv6 multicast routing issues described
below. It was tested with XORP 1.4/1.5 as the IPv6 PIM-SM routing
daemon against FreeBSD peers.
net/ipv6/ip6_input.c:
- Don't try to forward link-local multicast packets.
- Don't reset skb2->dev before calling ip6_mr_input() so packets can
be identified as coming from the PIM register vif properly.
net/ipv6/ip6mr.c:
- Fix incoming PIM register messages processing:
* The IPv6 pseudo-header should be included when checksumming PIM
messages (RFC 4601 section 4.9; RFC 3973 section 4.7.1).
* Packets decapsulated from PIM register messages should have
skb->protocol ETH_P_IPV6.
- Enable/disable IPv6 multicast forwarding on the corresponding
interface when a routing daemon adds/removes a multicast virtual
interface.
- Remove incorrect skb_pull() to fix userspace signaling.
- Enable/disable global IPv6 multicast forwarding when an IPv6
multicast routing socket is opened/closed.
net/ipv6/route.c:
- Don't use strict routing logic for packets decapsulated from PIM
register messages (similar to disabling rp_filter for the IPv4
case).
Signed-off-by: Thomas Goff <thomas.goff@boeing.com>
Reviewed-by: Fred Templin <fred.l.templin@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the xfrm reverse flow lookup for icmp6 so that icmp6 packets
don't get lost over ipsec tunnels. Similar patch is in RHEL5 kernel for a quite
long time and I do not see why it isn't in mainline.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to perform skb_postpull_rcsum after pulling the IPv6
header in order to maintain the correctness of the complete
checksum.
This patch also adds a missing iph reload after pulling.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a fib6 table dump is prematurely ended, we won't unlink
its walker from the list. This causes all sorts of grief for
other users of the list later.
Reported-by: Chris Caputo <ccaputo@alt.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
An old bug crept back into the ICMP/ICMPv6 conntrack protocols: the timeout
values are defined as unsigned longs, the sysctl's maxsize is set to
sizeof(unsigned int). Use unsigned int for the timeout values as in the
other conntrack protocols.
Reported-by: Jean-Mickael Guerin <jean-mickael.guerin@6wind.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (22 commits)
ioat: fix self test for multi-channel case
dmaengine: bump initcall level to arch_initcall
dmaengine: advertise all channels on a device to dma_filter_fn
dmaengine: use idr for registering dma device numbers
dmaengine: add a release for dma class devices and dependent infrastructure
ioat: do not perform removal actions at shutdown
iop-adma: enable module removal
iop-adma: kill debug BUG_ON
iop-adma: let devm do its job, don't duplicate free
dmaengine: kill enum dma_state_client
dmaengine: remove 'bigref' infrastructure
dmaengine: kill struct dma_client and supporting infrastructure
dmaengine: replace dma_async_client_register with dmaengine_get
atmel-mci: convert to dma_request_channel and down-level dma_slave
dmatest: convert to dma_request_channel
dmaengine: introduce dma_request_channel and private channels
net_dma: convert to dma_find_channel
dmaengine: provide a common 'issue_pending_all' implementation
dmaengine: centralize channel allocation, introduce dma_find_channel
dmaengine: up-level reference counting to the module level
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (84 commits)
wimax: fix kernel-doc for debufs_dentry member of struct wimax_dev
net: convert pegasus driver to net_device_ops
bnx2x: Prevent eeprom set when driver is down
net: switch kaweth driver to netdevops
pcnet32: round off carrier watch timer
i2400m/usb: wrap USB power saving in #ifdef CONFIG_PM
wimax: testing for rfkill support should also test for CONFIG_RFKILL_MODULE
wimax: fix kconfig interactions with rfkill and input layers
wimax: fix '#ifndef CONFIG_BUG' layout to avoid warning
r6040: bump release number to 0.20
r6040: warn about MAC address being unset
r6040: check PHY status when bringing interface up
r6040: make printks consistent with DRV_NAME
gianfar: Fixup use of BUS_ID_SIZE
mlx4_en: Returning real Max in get_ringparam
mlx4_en: Consider inline packets on completion
netdev: bfin_mac: enable bfin_mac net dev driver for BF51x
qeth: convert to net_device_ops
vlan: add neigh_setup
dm9601: warn on invalid mac address
...
This patch adds GRO support for TCP over IPv6. The code is exactly
the same as the IPv4 version except for the pseudo-header checksum
computation.
Note that I've removed the unused tcphdr argument from tcp_v6_check
rather than invent a bogus value for GRO.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds GRO support for IPv6. IPv6 GRO supports extension
headers in the same way as GSO (by using the same infrastructure).
It's also simpler compared to IPv4 since we no longer have to worry
about fragmentation attributes or header checksums.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the general-purpose channel allocation provided by dmaengine.
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Reported-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to excellent diagnosis by Eduard Guzovsky.
The core problem is that on a network with lots of active
multicast traffic, the neighbour cache can fill up. If
we try to allocate a new route and thus neighbour cache
entry, the bog-standard GC attempt the neighbour layer does
in ineffective because route entries hold a reference
to the existing neighbour entries and GC can only liberate
entries with no references.
IPV4 already has a way to handle this, by doing a route cache
GC in such situations (when neigh attach returns -ENOBUFS).
So simply mimick this on the ipv6 side.
Tested-by: Eduard Guzovsky <eguzovsky@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we converted the protocol atomic counters such as the orphan
count and the total socket count deadlocks were introduced due to
the mismatch in BH status of the spots that used the percpu counter
operations.
Based on the diagnosis and patch by Peter Zijlstra, this patch
fixes these issues by disabling BH where we may be in process
context.
Reported-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
1.When no interface is specified in an IPV6_PKTINFO ancillary data
item, the interface specified in an IPV6_PKTINFO sticky optionis
is used.
RFC3542:
6.7. Summary of Outgoing Interface Selection
This document and [RFC-3493] specify various methods that affect the
selection of the packet's outgoing interface. This subsection
summarizes the ordering among those in order to ensure deterministic
behavior.
For a given outgoing packet on a given socket, the outgoing interface
is determined in the following order:
1. if an interface is specified in an IPV6_PKTINFO ancillary data
item, the interface is used.
2. otherwise, if an interface is specified in an IPV6_PKTINFO sticky
option, the interface is used.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When get receiving interface index while no message is received,
the the value seted with setsockopt() should be returned.
RFC 3542:
Issuing getsockopt() for the above options will return the sticky
option value i.e., the value set with setsockopt(). If no sticky
option value has been set getsockopt() will return the following
values:
- For the IPV6_PKTINFO option, it will return an in6_pktinfo
structure with ipi6_addr being in6addr_any and ipi6_ifindex being
zero.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are three reasons for me to add this support:
1.When no interface is specified in an IPV6_PKTINFO ancillary data
item, the interface specified in an IPV6_PKTINFO sticky optionis
is used.
RFC3542:
6.7. Summary of Outgoing Interface Selection
This document and [RFC-3493] specify various methods that affect the
selection of the packet's outgoing interface. This subsection
summarizes the ordering among those in order to ensure deterministic
behavior.
For a given outgoing packet on a given socket, the outgoing interface
is determined in the following order:
1. if an interface is specified in an IPV6_PKTINFO ancillary data
item, the interface is used.
2. otherwise, if an interface is specified in an IPV6_PKTINFO sticky
option, the interface is used.
2.When no IPV6_PKTINFO ancillary data is received,getsockopt() should
return the sticky option value which set with setsockopt().
RFC 3542:
Issuing getsockopt() for the above options will return the sticky
option value i.e., the value set with setsockopt(). If no sticky
option value has been set getsockopt() will return the following
values:
3.Make the setsockopt implementation POSIX compliant.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This last patch makes the appropriate changes to use and propagate the
network namespace where needed in IPv6 multicast forwarding code.
This consists mainly in replacing all the remaining init_net occurences
with current netns pointer retrieved from sockets, net devices or
mfc6_caches depending on the routines' contexts.
Some routines receive a new 'struct net' parameter to propagate the current
netns:
* ip6mr_get_route
* ip6mr_cache_report
* ip6mr_cache_find
* ip6mr_cache_unresolved
* mif6_add/mif6_delete
* ip6mr_mfc_add/ip6mr_mfc_delete
* ip6mr_reg_vif
All the IPv6 multicast forwarding variables moved to struct netns_ipv6 by
the previous patches are now referenced in the correct namespace.
Changelog:
==========
* Take into account the net associated to mfc6_cache when matching entries in
mfc_unres_queue list.
* Call mroute_clean_tables() in ip6mr_net_exit() to free memory allocated
per-namespace.
* Call dev_net_set() in ip6mr_reg_vif() to initialize dev->nd_net
correctly.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare IPv6 multicast forwarding /proc/net entries per-namespace:
/proc/net/ip6_mr_vif
/proc/net/ip6_mr_cache
Changelog
=========
V2:
* In routine ipmr_mfc_seq_idx(), only match entries belonging to current
netns in mfc_unres_queue list.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preliminary work to make IPv6 multicast forwarding netns-aware.
Declare variable 'reg_vif_num' per-namespace, moves into struct netns_ipv6.
At the moment, this variable is only referenced in init_net.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preliminary work to make IPv6 multicast forwarding netns-aware.
Declare IPv6 multicast forwarding variables 'mroute_do_assert' and
'mroute_do_pim' per-namespace in struct netns_ipv6.
At the moment, these variables are only referenced in init_net.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preliminary work to make IPv6 multicast forwarding netns-aware.
Declare variable cache_resolve_queue_len per-namespace: moves it into
struct netns_ipv6.
This variable counts the number of unresolved cache entries queued in the
list mfc_unres_queue. This list is kept global to all netns as the number
of entries per namespace is limited to 10 (hardcoded in routine
ip6mr_cache_unresolved).
Entries belonging to different namespaces in mfc_unres_queue will be
identified by matching the mfc_net member introduced previously in
struct mfc6_cache.
Keeping this list global to all netns, also allows us to keep a single
timer (ipmr_expire_timer) to handle their expiration.
In some places cache_resolve_queue_len value was tested for arming
or deleting the timer. These tests were equivalent to testing
mfc_unres_queue value instead and are replaced in this patch.
At the moment, cache_resolve_queue_len is only referenced in init_net.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preliminary work to make IPv6 multicast forwarding netns-aware.
Dynamically allocates IPv6 multicast forwarding cache, mfc6_cache_array,
and moves it to struct netns_ipv6.
At the moment, mfc6_cache_array is only referenced in init_net.
Replace 'ARRAY_SIZE(mfc6_cache_array)' with mfc6_cache_array size: MFC6_LINES.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch stores into struct mfc6_cache the network namespace each
mfc6_cache belongs to. The new member is mfc6_net.
mfc6_net is assigned at cache allocation and doesn't change during
the rest of the cache entry life.
This will help to retrieve the current netns around the IPv6 multicast
forwarding code.
At the moment, all mfc6_cache are allocated in init_net.
Changelog:
==========
* Use write_pnet()/read_pnet() to set and get mfc6_net.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preliminary work to make IPv6 multicast forwarding netns-aware.
Dynamically allocates interface table vif6_table and moves it to
struct netns_ipv6, and updates MIF_EXISTS() macro.
At the moment, vif6_table is only referenced in init_net.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preliminary work to make IPv6 multicast forwarding netns-aware.
Make IPv6 multicast forwarding mroute6_socket per-namespace,
moves it into struct netns_ipv6.
At the moment, mroute6_socket is only referenced in init_net.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes minor annoyance during transmission of unsolicited
neighbor advertisements from userspace to multicast addresses (as
far as I can see in RFC, this is allowed and the similar functionality
for IPv4 has been in arping for a long time).
Outgoing multicast packets get reinserted into local processing as if they
are received from the network. The machine thus sees its own NA and fills
the logs with error messages. This patch removes the message if NA has been
generated locally.
Signed-off-by: Jan Sembera <jsembera@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today, iproute2 fails to show multicast forwarding unresolved cache
entries while scanning /proc/net/ip_mr_cache.
Indeed, it expects to see -1 in 'Iif' column to identify unresolved
entries but the kernel outputs 65535. It's a signed/unsigned issue:
'Iif', the source interface, is retrieved from member mfc_parent in
struct mfc_cache. mfc_parent is a vifi_t: unsigned short, but is
displayed in ipmr_mfc_seq_show() as "%-3d", signed integer.
In unresolevd entries, the 65535 value (0xFFFF) comes from this define:
#define ALL_VIFS ((vifi_t)(-1))
That may explains why the guy who added support for this in iproute2
thought a -1 should be expected.
I don't know if this must be fixed in kernel or in iproute2. Who is
right? What is the correct API? How was it designed originally?
I let you decide if it should goes in the kernel or be fixed in iproute2.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc/net/ip_mr_cache and /proc/net/ip6_mr_cache displays garbage when
showing unresolved mfc_cache entries.
[root@qemu tests]# cat /proc/net/ip_mr_cache
Group Origin Iif Pkts Bytes Wrong Oifs
014C00EF 010014AC 1 10 10050 0 2:1 3:1
024C00EF 010014AC 65535 514 2 -559067475
The first line is correct. It is a resolved cache entry, 10 packets used it...
The second line represents an unresolved entry, and the columns Pkts(4th),
Bytes(5th) and Wrong(6th) just show garbage.
In struct mfc_cache, there's an union to store data for resolved and
unresolved cases. And what ipmr_mfc_seq_show() is printing in these
columns for the unresolved entries is some bytes from mfc_cache.mfc_un.res.
Bad.
(eg. In our case -559067475 is in fact 0xdead4ead which is the spinlock
magic from mfc_cache.mfc_un.unres.unresolved.lock.magic).
This patch replaces the garbage data written in these columns for the
unresolved entries by '0' (zeros) which is more correct.
This change doesn't break the ABI.
Also, mfc->mfc_un.res.pkt, mfc->mfc_un.res.bytes, mfc->mfc_un.res.wrong_if
are unsigned long.
It applies on top of net-next-2.6.
The patch for net-2.6 is slightly different because of the NIP6_FMT to
%pI6 conversion that was made in the seq_printf.
Changelog:
==========
V2:
* Instead of breaking the ABI by suppressing the columns that have no
meaning for unresolved entries, fill them with 0 values.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
fs/nfsd/nfs4recover.c
Manually fixed above to use new creds API functions, e.g.
nfs4_save_creds().
Signed-off-by: James Morris <jmorris@namei.org>
Instead of using one atomic_t per protocol, use a percpu_counter
for "sockets_allocated", to reduce cache line contention on
heavy duty network servers.
Note : We revert commit (248969ae31
net: af_unix can make unix_nr_socks visbile in /proc),
since it is not anymore used after sock_prot_inuse_add() addition
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller
Ilpo Järvinen
Herbert Xu
Harvey Harrison
Dave Jones
Thomas Goff
Jiri Pirko
Patrick McHardy
Linus Torvalds
Fernando Carrijo
Dan Williams
James Morris
Yang Hongyang
Benjamin Thery
Jan Sembera
Joe Perches
Eric Dumazet