This pure device tree driver is simple to convert to use
just GPIO descriptors instead of GPIO numbers. So let's
just do it.
Cc: Mark Langsdorf <mlangsdo@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Marvell armada37xx, armada7k and armada8k share the same
AHCI sata controller IP, and currently there is an issue
(Errata Ref#226)that the SATA can not be detected via SATA
Port-MultiPlayer(PMP). After debugging, the reason is
found that the value of Port-x FIS-based Switching Control
(PxFBS@0x40) became wrong.
According to design, the bits[11:8, 0] of register PxFBS
are cleared when Port Command and Status (0x18) bit[0]
changes its value from 1 to 0, i.e. falling edge of Port
Command and Status bit[0] sends PULSE that resets PxFBS
bits[11:8; 0].
So it needs save the port PxFBS register before PxCMD
ST write and restore the port PxFBS register afterwards
in ahci_stop_engine().
This commit allows drivers to override ahci_stop_engine
behavior for use by the Marvell AHCI driver(and potentially
other drivers in the future).
Signed-off-by: Evan Wang <xswang@marvell.com>
Cc: Ofer Heifetz <oferh@marvell.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, ahci supports only msi and intx. To also support msix the
handling of the irq number need to be changed. The irq number for msix
devices is taken from msi_list instead of pci_dev. Thus, the irq
number of a device needs to be stored in struct ahci_host_priv now.
This allows the host controller to be activated in a generic way.
This change is only intended for ahci drivers. For that reason the irq
number is stored in struct ahci_host_priv used only by ahci drivers.
Thus, the ABI changes only for ahci_host_activate(), but existing ata
drivers (about 50) are unaffected and keep unchanged. All users of
ahci_host_activate() have been updated.
While touching drivers/ata/libahci.c, doing a small code cleanup in
ahci_port_start().
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently host activation done by calling either function
ahci_host_activate() or ata_host_activate(). Consolidate
the code by only calling ahci_host_activate() for all AHCI
devices.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
This patch moves force_port_map and mask_port_map into the
ahci_host_priv structure. This allows to modify them into the AHCI
framework. This is needed by the new dt bindings representing ports as
the port_map mask is computed automatically.
Parameters modifying force_port_map, mask_port_map and flags have been
removed from the ahci_platform_init_host() function, and inputs in the
ahci_host_priv structure are now directly filed.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
hpriv->plat_data is 'void *' so there is no need to cast it to
'struct ecx_plat_data *'.
Cc: Mark Langsdorf <mark.langsdorf@calxeda.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Allwinner A10 and A20 ARM SoCs have an AHCI sata controller which needs a
special register to be poked before starting the DMA engine.
This register gets reset on an ahci_stop_engine call, so there is no other
place then ahci_start_engine where this poking can be done.
This commit allows drivers to override ahci_start_engine behavior for use by
the Allwinner AHCI driver (and potentially other drivers in the future).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Cc: linux-ide@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The sata-highbank driver is a complete standalone sata driver, which does
not use ahci_platform.c / ahci_platform_data in any way.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The original code used the wrong parameter to clear tx_atten[]. It
passed the number of elements instead of sizeof() the array to memset.
The other potential issue was that cphy_base[] wasn't cleared. I'm not
sure if that was a real problem or not, but I have cleared it in my
patch.
Instead of using memset(), this patch uses empty initializers as a
cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata changes from Tejun Heo:
"Two interesting changes.
- libata acpi handling has been restructured so that the association
between ata devices and ACPI handles are less convoluted. This
change shouldn't change visible behavior.
- Queued TRIM support, which enables sending TRIM to the device
without draining in-flight RW commands, is added. Currently only
enabled for ahci (and likely to stay that way for the foreseeable
future).
Other changes are driver-specific updates / fixes"
* 'for-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: bugfix: Remove __le32 in ata_tf_to_fis()
libata: acpi: Remove ata_dev_acpi_handle stub in libata.h
libata: Add support for queued DSM TRIM
libata: Add support for SEND/RECEIVE FPDMA QUEUED
libata: Add H2D FIS "auxiliary" port flag
libata: Populate host-to-device FIS "auxiliary" field
ata: acpi: rework the ata acpi bind support
sata, highbank: send extra clock cycles in SGPIO patterns
sata, highbank: set tx_atten override bits
devicetree: create a separate binding description for sata_highbank
drivers/ata/sata_rcar.c: simplify use of devm_ioremap_resource
sata highbank: enable 64-bit DMA mask when using LPAE
ata: pata_samsung_cf: add missing __iomem annotation
ata: pata_arasan: Staticize local symbols
sata_mv: Remove unneeded CONFIG_HAVE_CLK ifdefs
ata: use dev_get_platdata()
sata_mv: Remove unneeded forward declaration
libata: acpi: remove dead code for ata_acpi_(un)bind
libata: move 'struct ata_taskfile' and friends from ata.h to libata.h
Some SGPIO PICs don't follow the standard very well and expect a certain
number of clock cycles or port frames in each SGPIO pattern. Add two
optional parameters in the DTB that can provide the number of extra
clock cycles to be sent before and after SGPIO pattern. Read those
parameters from the DTB and send the extra clock cycles.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some board designs do not drive the SATA transmit lines within the
specification. The ECME can provide override settings, on a per board
basis, to bring the transmit lines within spec. Read those settings
from the DTB and program them in.
At the time of submission, no production hardware requires this patch.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The ACTIVITY and ERROR signals were reversed in the original commit.
Fix that so that hard drive activity does not show up on the error
light, and attempts to indicate that the hard drive is failing do
not show up as hard drive activity. This fixes a fairly serious
functional bug in the driver, but failing to apply this patch will
not cause any stability issues on the system.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
libata/for-3.10-fixes never got submitted during v3.10 cycle. Merge
it into for-3.11 so that it can be routed together with other changes
scheduled for v3.11.
Three trivial conflicts in drivers/ata/sata_rcar.c. All are caused by
1b20f6a9ad ("sata_rcar: add 'base' local variable to some functions")
conflicting with logic updates in for-3.10-fixes. The offending
commit simply adds local variable @base on functions which
dereferences sata_rcar_priv->base multiple times. The resolutions are
trivial - applying s/priv->base/base/ in the conflicting logic
updates.
Signed-off-by: Tejun Heo <tj@kernel.org>
Highbank supports SGPIO by bit-banging out the SGPIO signals over
three GPIO pins defined in the DTB. Add support for this SGPIO
functionality.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Increase the retry count for the hard reset function to 100 but
shorten the time out period to 500 ms. See the comment for
ahci_highbank_hardreset for the reasons why those vaulues were
chosen.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
mkinitrd looks at /sys/class/scsi_host/host$hostnum/proc_name to find
the module name of a disk driver. Current name is "highbank-ahci" but
the module is "sata_highbank". Rename it to match the module name.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: <stable@vger.kernel.org> v3.7..
Signed-off-by: Robert Richter <robert.richter@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make ahci_highbank_pm_ops static because ahci_highbank_pm_ops is
not exported.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ahci_highbank_hardreset() uses bare number for the BSY bit of the ATA status
register, despite it is #define'd in <linux/ata.h>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This will fix warnings like following when CONFIG_PM_SLEEP is not set:
warning: 'xxx_suspend' defined but not used [-Wunused-function]
warning: 'xxx_resume' defined but not used [-Wunused-function]
Because
SET_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)
Only references the callbacks on CONFIG_PM_SLEEP (instead of CONFIG_PM).
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ahci_highbank_probe function is incorrectly marked as __init,
which means it can get discarded at boot time, which might be
a problem if for some reason the device only becomes operational
after loading another module.
Using __devinit instead avoids seeing this warning for every build:
WARNING: vmlinux.o(.data+0xf7b0): Section mismatch in reference from the
variable ahci_highbank_driver to the function .init.text:ahci_highbank_probe()
The variable ahci_highbank_driver references
the function __init ahci_highbank_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mark Langsdorf <mark.langsdorf@calxeda.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Calxeda highbank SATA phy has intermittent problems bringing up a link
with Gen3 drives. Retrying the phy hard reset can work-around this issue,
but each reset also disables spread spectrum support. The reset function
also needs to reprogram the phy to enable spread spectrum support.
Create a new driver based on ahci_platform to support the Calxeda Highbank
SATA controller.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Linus Walleij
Evan Wang
Arnd Bergmann
Robert Richter
Wolfram Sang
Alexander Gordeev
Antoine Ténart
Bartlomiej Zolnierkiewicz
Hans de Goede
Paul Gortmaker
Dan Carpenter
Linus Torvalds
Mark Langsdorf
Rob Herring
Tejun Heo
Robert Richter
Jingoo Han
Greg Kroah-Hartman
Brian Norris
Sergei Shtylyov
Yuanhan Liu