The chip id for SUMO2 isn't used.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=63935
Tested-By: Dave Witbrodt <dawitbro@sbcglobal.net>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Daniel writes:
A few fixes, nothing shocking:
- More Haswell pci ids. Includes a pile of marketing spare ids (which
despite the spare moniker show up all over the place).
- Fix a regression in handling modeset failures, resulting in black
screens on 3 pipe setups when we've run out of pch plls (Chris).
- Fix up the setcrtc semantics to unconditionally enable the outputs.
Juding from git digging that has (kinda) always been the case and neatly
fixes a few long-standing (i.e. forever) bug reports (Imre).
- jiffies_timeout + 1 patches from Imre. They partially fix spurious
wait_event failures in the interrupt-driven dp aux/i2c code. The other
part is a core patch for the wait_event macros going in through -mm. A
few patches more than strictly required since Imre is pushing for a
general solution in 3.11.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: avoid premature DP AUX timeouts
drm/i915: avoid premature timeouts in __wait_seqno()
drm/i915: use msecs_to_jiffies_timeout instead of open coding the same
drm/i915: add msecs_to_jiffies_timeout to guarantee minimum duration
drm/i915: force full modeset if the connector is in DPMS OFF mode
drm/i915: Propagate errors back from fb set-base
drm/i915: Adding more reserved PCI IDs for Haswell.
Inki writes:
This pull request includes drm_send_vblank_event() helper
relevant patch I missed and code cleanups. And also it fixes
a pended page flip issue.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: replace request_threaded_irq with devm function
drm/exynos: remove unnecessary devm_kfree
drm/exynos: fix build warnings from ipp fimc
drm/exynos: cleanup device pointer usages
drm/exynos: wait for the completion of pending page flip
drm/exynos: use drm_send_vblank_event() helper
drm/exynos: page flip fixes
drm/exynos: exynos_hdmi: Pass correct pointer to free_irq()
drm/exynos: exynos_drm_ipp: Fix incorrect usage of IS_ERR_OR_NULL
drm/exynos: exynos_drm_fbdev: Fix incorrect usage of IS_ERR_OR_NULL
Conflicts:
drivers/gpu/drm/exynos/exynos_hdmi.c
devm_request_threaded_irq is used instead of request_threaded_irq
and free_irq is removed.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
devm_kfree does not need for fail case of probe function and for
remove function.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Becuase of order of headers, there are build warnings and they are
fixed with this patch.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Struct device pointer got from platform device pointer is already
alsigned as variable, but some functions do not use device pointer.
So this patch replaces thoes usages.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch fixes the issue that drm_vblank_get() is failed.
The issus occurs when next page flip request is tried
if previous page flip event wasn't completed yet and then
dpms became off.
So this patch make sure that page flip event is completed
before dpms goes to off.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
When booting with DT, there's a crash when omapfb is probed. This is
caused by the fact that omapdss+DT is not yet supported, and thus
omapdss is not probed at all. On the other hand, omapfb is always
probed. When omapfb tries to use omapdss, there's a NULL pointer
dereference crash. The same error should most likely happen with omapdrm
and omap_vout also.
To fix this, add an "initialized" state to omapdss. When omapdss has
been probed, it's marked as initialized. omapfb, omapdrm and omap_vout
check this state when they are probed to see that omapdss is actually
there.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
During DP AUX communication we might time out 1 jiffy too early, because
the calculated expiry jiffy value is one less than needed.
This is only one reason for false DP AUX timeouts. For a complete
solution we also need the following fix, which is now queued for
mainline: http://marc.info/?l=linux-kernel&m=136748515710837&w=2
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64133
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At the moment wait_event_timeout/wait_event_interruptible_timeout may
time out 1 jiffy too early, as the calculated expiry time is 1 less than
needed. Besides timing out too early this also means that the
calculation of the remaining time will be incorrect and we will pass a
non-zero remaining time to user space in case of a time out. This is one
reason for the following bugzilla report:
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64270
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this to avoid premature timeouts whenever scheduling a timeout
based on the current jiffies value. For an explanation see [1].
The following patches will take the helper into use.
Once the more generic solution proposed in the thread at [1] is accepted
this patch can be reverted while keeping the follow-up patches.
[1] http://marc.info/?l=linux-kernel&m=136854294730957&w=2
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the driver's assumed behavior for a modeset with an attached
FB is that the corresponding connector will be switched to DPMS ON mode
if it happened to be in DPMS OFF (or another power save mode). This
wasn't enforced though if only the FB changed, everything else (format,
connector etc.) remaining the same. In this case we only set the new FB
base and left the connector in the old power save mode.
Fix this by forcing a full modeset whenever there is an attached FB and
any affected connector is in a power save mode.
V_2: Run the test for encoders in power save mode outside the the
test for fb change: user space may have just disabled the encoders
but left everything else in place. Make sure the connector list is
not empty before running this test.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Egbert Eich <eich@suse.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61642
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59834
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59339
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64178
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Apply Jani's s/connector_off/is_crtc_connector_off bikeshed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The event wouldn't be on any list at this point, so nothing to delete
it from.
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
free_irq() expects the same pointer that was passed to request_threaded_irq(),
otherwise the IRQ is not freed.
The issue was found using the following coccinelle script:
<smpl>
@r1@
type T;
T devid;
@@
request_threaded_irq(..., devid)
@r2@
type r1.T;
T devid;
position p;
@@
free_irq@p(..., devid)
@@
position p != r2.p;
@@
*free_irq@p(...)
</smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Pull radeon sun/hainan support from Dave Airlie:
"Since I know its outside the merge window, but since this is new hw I
thought I'd try and provoke the new hw exception, it just fills in the
blanks in the driver for the new AMD sun and hainan chipsets."
* 'drm-radeon-sun-hainan' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: add Hainan pci ids
drm/radeon: add golden register settings for Hainan (v2)
drm/radeon: sun/hainan chips do not have UVD (v2)
drm/radeon: track which asics have UVD
drm/radeon: radeon-asic updates for Hainan
drm/radeon: fill in ucode loading support for Hainan
drm/radeon: don't touch DCE or VGA regs on Hainan (v3)
drm/radeon: fill in GPU init for Hainan (v2)
drm/radeon: add chip family for Hainan
Pull DRM fixes from Dave Airlie:
"This is just a set of nouveau and radeon fixes, the nouveau ones fix
some suspend/resume regressions since use of copy engines and some
fixes for Z compression on some newer chipsets."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/dce2: use 10khz units for audio dto calculation
drm/radeon: Fix VRAM size calculation for VRAM >= 4GB
drm/radeon: Remove superfluous variable
drm/nouveau: ensure channels are stopped before saving fences for suspend
drm/nv50/fifo: prevent races between clients updating playlists
drm/nvc0/fifo: prevent CHAN_TABLE_ERROR:CHANNEL_PENDING on fifo fini
drm/nvc0/fifo: prevent races between clients updating playlists
drm/nve0/fifo: prevent races between clients updating playlists
drm/nve0/ltcg: poke the partition count into yet another register
drm/nvc0/ltcg: fix handling of disabled partitions
drm/nvc0/ce: disable ce1 on a number of chipsets
drm/nouveau/bios: fix thinko in ZM_MASK_ADD opcode
drm/nouveau: fix build with nv50->nvc0
Along the modesetting short cut where we skip trying to do a full
modeset and instead simply update the framebuffer base registers, we
failed to handle any errors reported.
This regression has been introduced in
commit 94352cf9a5
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 5 22:51:56 2012 +0200
drm/i915: push crtc->fb update into pipe_set_base
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At DDX commit Chris mentioned the tendency we have of finding out more
PCI IDs only when users report. So Let's add all new reserved Haswell IDs.
This patch also fix GT3 names. I'no not sending in separated patche because
names are only in few comments and not in variable names.
v2: Fix some mobile ids (by Paulo)
References: http://bugs.freedesktop.org/show_bug.cgi?id=63701
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Hainan has no display hardware:
- no DCE (crtc, uniphy, dac, etc.)
- no VGA
v2: fix bios fetch
v3: fix interrupts
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Avoids overflows on DCE2.x devices. Also clarify the calculation
on other asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
bool in_mode_set from struct radeon_crtc is not used anymore.
Signed-off-by: Niels Ole Salscheider <niels_ole@salscheider-online.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes some s/r problem with copy engines and ZCULL issues and playlist issues
* 'drm-nouveau-fixes-3.10' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau: ensure channels are stopped before saving fences for suspend
drm/nv50/fifo: prevent races between clients updating playlists
drm/nvc0/fifo: prevent CHAN_TABLE_ERROR:CHANNEL_PENDING on fifo fini
drm/nvc0/fifo: prevent races between clients updating playlists
drm/nve0/fifo: prevent races between clients updating playlists
drm/nve0/ltcg: poke the partition count into yet another register
drm/nvc0/ltcg: fix handling of disabled partitions
drm/nvc0/ce: disable ce1 on a number of chipsets
drm/nouveau/bios: fix thinko in ZM_MASK_ADD opcode
drm/nouveau: fix build with nv50->nvc0
The falcon is present, but the rest of the copy engine doesn't appear to
be... PUNITS doesn't report disabled (maybe the bits for the copy engines
got added later?), so we end up trying to use a non-functional CE1, and
bust all sorts of things.. Most notably, suspend/resume..
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Pull devm usage cleanup from Wolfram Sang:
"Lately, I have been experimenting how to improve the devm interface to
make writing device drivers easier and less error prone while also
getting rid of its subtle issues. I think it has more potential but
still needs work and definately conistency, especiall in its usage.
The first thing I come up with is a low hanging fruit regarding
devm_ioremap_resouce(). This function already checks if the passed
resource is valid and gives an error message if not. So, we can
remove similar checks from the drivers and get rid of a bit of code
and a number of inconsistent error strings.
This series only removes the unneeded check iff devm_ioremap_resource
follows platform_get_resource directly. The previous version tried to
shuffle code if needed, too, what lead to an embarrasing bug. It
turned out to me that shuffling code for all cases found will make the
automated script too complex, so I am unsure if an automated cleanup
is the proper tool for this case. Removing the easy stuff seems
worthwhile to me, though.
Despite various architectures and platform dependencies, I managed to
compile test 45 out of 57 modified files locally using heuristics and
defconfigs."
Pulled because: 296 deletions, 0 additions.
* 'devm_no_resource_check' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (33 commits)
sound/soc/kirkwood: don't check resource with devm_ioremap_resource
sound/soc/fsl: don't check resource with devm_ioremap_resource
arch/mips/lantiq/xway: don't check resource with devm_ioremap_resource
arch/arm/plat-samsung: don't check resource with devm_ioremap_resource
arch/arm/mach-tegra: don't check resource with devm_ioremap_resource
drivers/watchdog: don't check resource with devm_ioremap_resource
drivers/w1/masters: don't check resource with devm_ioremap_resource
drivers/video/omap2/dss: don't check resource with devm_ioremap_resource
drivers/video/omap2: don't check resource with devm_ioremap_resource
drivers/usb/phy: don't check resource with devm_ioremap_resource
drivers/usb/host: don't check resource with devm_ioremap_resource
drivers/usb/gadget: don't check resource with devm_ioremap_resource
drivers/usb/chipidea: don't check resource with devm_ioremap_resource
drivers/thermal: don't check resource with devm_ioremap_resource
drivers/staging/nvec: don't check resource with devm_ioremap_resource
drivers/staging/dwc2: don't check resource with devm_ioremap_resource
drivers/spi: don't check resource with devm_ioremap_resource
drivers/rtc: don't check resource with devm_ioremap_resource
drivers/pwm: don't check resource with devm_ioremap_resource
drivers/pinctrl: don't check resource with devm_ioremap_resource
...
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull drm fixes from Dave Airlie:
"Fix for radeon nomodeset regression, old radeon interface cliprects
fix, 2 qxl crasher fixes, and a couple of minor cleanups.
I may have a new AMD hw support branch next week, its one of those
doesn't affect anything existing just adds new support, I'll see how
it shapes up and I might ask you to take it, just thought I'd warn in
advance."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: restore nomodeset operation (v2)
qxl: fix bug with object eviction and update area
drm/qxl: drop active_user_framebuffer as its unneeded
qxl: drop unused variable.
drm/qxl: fix ioport interactions for kernel submitted commands.
drm: remove unused wrapper macros
drm/radeon: check incoming cliprects pointer
When UMS was deprecated it removed support for nomodeset commandline
we really want this in distro land so we can debug stuff, everyone
should fallback to vesa correctly.
v2: oops -1 isn't used anymore, restore original behaviour
-1 is default, so we can boot with nomodeset on the command line,
then use radeon.modeset=1 to override it for debugging later.
Cc: stable@vger.kernel.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
if the surface is evicted, this validation will happen
to the wrong place, I noticed this with other work I was
doing, haven't seen it go wrong in practice.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This was a bogus way to figure out what the active framebuffer was,
just check if the underlying bo is the primary bo.
Signed-off-by: Dave Airlie <airlied@redhat.com>
So qxl has ioports, but it really really really doesn't want you
to write to them twice, but if you write and get a signal before
the irq arrives to let you know its completed, you have to think
ahead and avoid writing another time.
However this works fine for update area where really multiple
writes aren't the end of the world, however with create primary
surface, you can't ever do multiple writes. So this stop internal
kernel writes from doing interruptible waits, because otherwise
we have no idea if this write is a new one or a continuation of
a previous one.
virtual hw sucks more than real hw.
This fixes lockups and VM crashes when resizing and starting/stopping
X.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Old code assumed framebuffer starts at base of stolen memory. Since the
addition of hardware cursors, this might not be true anymore so add the
gtt offset to the calculation.
Reported-by: Holger Schurig <holgerschurig@gmail.com>
Tested-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Pull drm fixes from Dave Airlie:
"Just a few straggling fixes I hoovered up, and an intel fixes pull
from Daniel which fixes some regressions, and some mgag200 fixes from
Matrox."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux:
drm/mgag200: Fix framebuffer base address programming
drm/mgag200: Convert counter delays to jiffies
drm/mgag200: Fix writes into MGA1064_PIX_CLK_CTL register
drm/mgag200: Don't change unrelated registers during modeset
drm: Only print a debug message when the polled connector has changed
drm: Make the HPD status updates debug logs more readable
drm: Use names of ioctls in debug traces
drm: Remove pointless '-' characters from drm_fb_helper documentation
drm: Add kernel-doc for drm_fb_helper_funcs->initial_config
drm: refactor call to request_module
drm: Don't prune modes loudly when a connector is disconnected
drm: Add missing break in the command line mode parsing code
drm/i915: clear the stolen fb before resuming
Revert "drm/i915: Calculate correct stolen size for GEN7+"
drm/i915: hsw: fix link training for eDP on port-A
Revert "drm/i915: revert eDP bpp clamping code changes"
drm: don't check modeset locks in panic handler
drm/i915: Fix pipe enabled mask for pipe C in WM calculations
drm/mm: fix dump table BUG
drm/i915: Always normalize return timeout for wait_timeout_ioctl
The "boxes" parameter points into userspace memory. It should be verified
like any other operation against user memory.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Higher bits of the base address of framebuffers weren't being
programmed properly. This caused framebuffers that didn't happen to be
allocated at a low enough address to not be displayed properly.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Signed-off-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The original line,
WREG_DAC(MGA1064_PIX_CLK_CTL_CLK_DIS, tmp);
wrote tmp into MGA1064_PIX_CLK_CTL_CLK_DIS, where
MGA1064_PIX_CLK_CTL_CLK_DIS is an offset into
MGA1064_PIX_CLK_CTL. Change the line to write properly into
MGA1064_PIX_CLK_CTL. There were other chunks of code nearby that use
the same pattern (but work correctly), so this patch updates them all
to use this new (slightly more efficient) write pattern. The WREG_DAC
macro was causing the DAC_INDEX register to be set to the same value
twice. WREG8(DAC_DATA, foo) takes advantage of the fact that DAC_INDEX
is already at the value we want.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Registers in indices below 0x18 are totally unrelated to modesetting,
so don't write 0's, or anything else into them on modeset. Most of
these registers are hardware cursor related, so this existing code
interferes with hardware cursor development.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
Tested-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Julia Lemire <jlemire@matrox.com>
Acked-by: Mathieu Larouche <mathieu.larouche@matrox.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of just printing "status updated from 1 to 2", make those enum
numbers immediately readable.
v2: Also patch output_poll_execute() (Daniel Vetter)
v3: Use drm_get_connector_status_name (Ville Syrjälä)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (for v1)
Signed-off-by: Dave Airlie <airlied@redhat.com>
The intention here is to make the output of dmesg with full verbosity a
bit easier for a human to parse. This commit transforms:
[drm:drm_ioctl], pid=699, cmd=0x6458, nr=0x58, dev 0xe200, auth=1
[drm:drm_ioctl], pid=699, cmd=0xc010645b, nr=0x5b, dev 0xe200, auth=1
[drm:drm_ioctl], pid=699, cmd=0xc0106461, nr=0x61, dev 0xe200, auth=1
[drm:drm_ioctl], pid=699, cmd=0xc01c64ae, nr=0xae, dev 0xe200, auth=1
[drm:drm_mode_addfb], [FB:32]
[drm:drm_ioctl], pid=699, cmd=0xc0106464, nr=0x64, dev 0xe200, auth=1
[drm:drm_vm_open_locked], 0x7fd9302fe000,0x00a00000
[drm:drm_ioctl], pid=699, cmd=0x400c645f, nr=0x5f, dev 0xe200, auth=1
[drm:drm_ioctl], pid=699, cmd=0xc00464af, nr=0xaf, dev 0xe200, auth=1
[drm:intel_crtc_set_config], [CRTC:3] [NOFB]
into:
[drm:drm_ioctl], pid=699, dev=0xe200, auth=1, I915_GEM_THROTTLE
[drm:drm_ioctl], pid=699, dev=0xe200, auth=1, I915_GEM_CREATE
[drm:drm_ioctl], pid=699, dev=0xe200, auth=1, I915_GEM_SET_TILING
[drm:drm_ioctl], pid=699, dev=0xe200, auth=1, IOCTL_MODE_ADDFB
[drm:drm_mode_addfb], [FB:32]
[drm:drm_ioctl], pid=699, dev=0xe200, auth=1, I915_GEM_MMAP_GTT
[drm:drm_vm_open_locked], 0x7fd9302fe000,0x00a00000
[drm:drm_ioctl], pid=699, dev=0xe200, auth=1, I915_GEM_SET_DOMAIN
[drm:drm_ioctl], pid=699, dev=0xe200, auth=1, DRM_IOCTL_MODE_RMFB
[drm:intel_crtc_set_config], [CRTC:3] [NOFB]
v2: drm_ioctls is now a constant (Ville Syrjälä)
Signed-off-by: Chris Cummins <christopher.e.cummins@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reduces the size of the stack frame when calling request_module().
Performing the sprintf before the call is not needed.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_helper_probe_single_connector_modes() is responsible for pruning the
previously detected modes on a disconnected connector. We don't really
need to log, again, the full list of modes that used to be valid when
connected.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
As we parse the string given on the command line one char at a time, it
seems that we do want a break at every case.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel writes:
A few intel fixes for smaller issues and one revert for an sdv hack which
we've wanted to kill anyway. Plus two drm patches included for your
convenience, both regression fixers for mine own screw-ups.
+ both fixes for stolen mem handling.
* 'for-linux-next' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: clear the stolen fb before resuming
Revert "drm/i915: Calculate correct stolen size for GEN7+"
drm/i915: hsw: fix link training for eDP on port-A
Revert "drm/i915: revert eDP bpp clamping code changes"
drm: don't check modeset locks in panic handler
drm/i915: Fix pipe enabled mask for pipe C in WM calculations
drm/mm: fix dump table BUG
drm/i915: Always normalize return timeout for wait_timeout_ioctl
Similar to
commit 88afe715dd
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Sun Dec 16 12:15:41 2012 +0000
drm/i915: Clear the stolen fb before enabling
but on the resume path.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=57191
Reported-and-tested-by: Nikolay Amiantov <nikoamia@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org (3.9 only)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 03752f5b7b.
This revert requires a bit of explanation on how I understand things
work. Internally the architects/designers decide how the stolen encoding
works. We put it in a doc. BIOS writers take these docs and implement
it. Driver writers read the doc too, and read the value left by the BIOS
writers, and then we make magic.
The failing here is that in the docs we had[1] contained two different
definitions for this register for Gen7. (We have both a PCI register,
and an MMIO, and each of these were different). At the time [2] of
03752f5, we asked the architects what the correct value should be; but
that doesn't match the reality (BIOS) unfortunately.
So on all machines I can get my hands on, this revert is the right thing
to do. I've also worked with the product group to confirm that they
agree this revert is what we should do. People using HW made my "people"
who both write their own BIOS, and have access to our docs (Apple?).
Investigations are still ongoing about whether we need to add a list
of machines needing special handling, but this patch should be the
right thing for pretty much everyone.
[1] The docs are still wrong on this one. Now instead of two registers with
two definitions, we have one register with BOTH definitions, progress?
[2] The open source PRMs have the "wrong" definitions in chapter Volume
1 part6, section 1.1.12.
This digging was inspired by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Augment the patch saying that it's still a bit unclear
whether there are any machines out there with "wrong" firmware and
whether we need to add a list to handle them specially.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to BSpec the link training sequence for eDP on HSW port-A
should be as follows:
1. link training: clock recovery
2. link training: equalization
3. link training: set idle transmission mode
4. display pipe enable
5. link training: disable (set normal mode)
Contrary to this at the moment we don't do step 3. and we do step 5.
before step 4. Fix this by setting idle transmission mode for eDP at
the end of intel_dp_complete_link_train and adding a new
intel_dp_stop_link_training function to disable link training. With
these changes we'll end up with the following functions corresponding
to the above steps:
intel_dp_start_link_train -> step 1.
intel_dp_complete_link_train -> step 2., step 3.
intel_dp_stop_link_train -> step 5.
For port-A we'll call intel_dp_stop_link_train only after enabling the
pipe, for everything else we'll call it right after
intel_dp_complete_link_train to preserve the current behavior.
Tested on HSW/HSW-ULT.
In v2:
- Due to a HW issue we must set idle transmission mode for port-A too
before enabling the pipe. Thanks for Arthur Runyan for explaining
this.
- Update the patch subject to make it clear that it's an eDP fix, DP is
not affected.
v3:
- rename intel_dp_link_train() to intel_dp_set_link_train(), use 'val'
instead 'l' as var name. (Paulo)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 57c2196332.
It's an ugly hack for a Haswell SDV platform where the vbt doesn't
seem to fully agree with the panel. Since it seems to cause issues on
real eDP platform let's just kill this hack again.
Reported-and-tested-by: Josh Boyer <jwboyer@gmail.com>
References: https://lkml.org/lkml/2013/5/3/467
Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 3.10.
Wierd bits:
- OMAP drm changes required OMAP dss changes, in drivers/video, so I
took them in here.
- one more fbcon fix for font handover
- VT switch avoidance in pm code
- scatterlist helpers for gpu drivers - have acks from akpm
Highlights:
- qxl kms driver - driver for the spice qxl virtual GPU
Nouveau:
- fermi/kepler VRAM compression
- GK110/nvf0 modesetting support.
Tegra:
- host1x core merged with 2D engine support
i915:
- vt switchless resume
- more valleyview support
- vblank fixes
- modesetting pipe config rework
radeon:
- UVD engine support
- SI chip tiling support
- GPU registers initialisation from golden values.
exynos:
- device tree changes
- fimc block support
Otherwise:
- bunches of fixes all over the place."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (513 commits)
qxl: update to new idr interfaces.
drm/nouveau: fix build with nv50->nvc0
drm/radeon: fix handling of v6 power tables
drm/radeon: clarify family checks in pm table parsing
drm/radeon: consolidate UVD clock programming
drm/radeon: fix UPLL_REF_DIV_MASK definition
radeon: add bo tracking debugfs
drm/radeon: add new richland pci ids
drm/radeon: add some new SI PCI ids
drm/radeon: fix scratch reg handling for UVD fence
drm/radeon: allocate SA bo in the requested domain
drm/radeon: fix possible segfault when parsing pm tables
drm/radeon: fix endian bugs in atom_allocate_fb_scratch()
OMAPDSS: TFP410: return EPROBE_DEFER if the i2c adapter not found
OMAPDSS: VENC: Add error handling for venc_probe_pdata
OMAPDSS: HDMI: Add error handling for hdmi_probe_pdata
OMAPDSS: RFBI: Add error handling for rfbi_probe_pdata
OMAPDSS: DSI: Add error handling for dsi_probe_pdata
OMAPDSS: SDI: Add error handling for sdi_probe_pdata
OMAPDSS: DPI: Add error handling for dpi_probe_pdata
...
Merge the fixes for the server driver dirty update paths
* server-fixes:
drm/cirrus: deal with bo reserve fail in dirty update path
drm/ast: deal with bo reserve fail in dirty update path
drm/mgag200: deal with bo reserve fail in dirty update path
Just some fixes that have accumulated over the last couple of
weeks and some new PCI ids.
* 'drm-next-3.10-2' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix handling of v6 power tables
drm/radeon: clarify family checks in pm table parsing
drm/radeon: consolidate UVD clock programming
drm/radeon: fix UPLL_REF_DIV_MASK definition
radeon: add bo tracking debugfs
drm/radeon: add new richland pci ids
drm/radeon: add some new SI PCI ids
drm/radeon: fix scratch reg handling for UVD fence
drm/radeon: allocate SA bo in the requested domain
drm/radeon: fix possible segfault when parsing pm tables
drm/radeon: fix endian bugs in atom_allocate_fb_scratch()
Pull i2c changes from Wolfram Sang:
- an arbitration driver. While the driver is quite simple, it caused
discussion if we need additional arbitration on top of the one
specified in the I2C standard. Conclusion is that I accept a few
generic mechanisms, but not very specific ones.
- the core lost the detach_adapter() call. It has no users anymore and
was in the way for other cleanups. attach_adapter() is sadly still
there since there are users waiting to be converted.
- the core gained a bus recovery infrastructure. I2C defines a way to
recover if the data line is stalled. This mechanism is now in the
core and drivers can now pass some data to make use of it.
- bigger driver cleanups for designware, s3c2410
- removing superfluous refcounting from drivers
- removing Ben Dooks as second maintainer due to inactivity. Thanks
for all your work so far, Ben!
- bugfixes, feature additions, devicetree fixups, simplifications...
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: xiic: must always write 16-bit words to TX_FIFO
i2c: octeon: use HZ in timeout value
i2c: octeon: Fix i2c fail problem when a process is terminated by a signal
i2c: designware-pci: drop superfluous {get|put}_device
i2c: designware-plat: drop superfluous {get|put}_device
i2c: davinci: drop superfluous {get|put}_device
MAINTAINERS: Ben Dooks is inactive regarding I2C
i2c: mux: Add i2c-arb-gpio-challenge 'mux' driver
i2c: at91: convert to dma_request_slave_channel_compat()
i2c: mxs: do error checking and handling in PIO mode
i2c: mxs: remove races in PIO code
i2c-designware: switch to use runtime PM autosuspend
i2c-designware: use usleep_range() in the busy-loop
i2c-designware: enable/disable the controller properly
i2c-designware: use dynamic adapter numbering on Lynxpoint
i2c-designware-pci: use managed functions pcim_* and devm_*
i2c-designware-pci: use dev_err() instead of printk()
i2c-designware: move to managed functions (devm_*)
i2c: remove CONFIG_HOTPLUG ifdefs
i2c: s3c2410: Add SMBus emulation for block read
...
Since we know that locking is broken in that case and it's more
important to not flood the dmesg with random gunk.
Cc: Dave Airlie <airlied@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
References: http://lkml.kernel.org/r/20130502000206.GH15623@pd.tnic
Cc: stable@vger.kernel.org
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We actually care about the chip family rather than the
DCE version although functionally they are the same.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead of duplicating the code over and over again, just use a single
function to handle the clock calculations.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stupid copy & paste error over all generations.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is to allow debugging of userspace program not freeing buffer
after, which is basicly a memory leak. This print the list of all
gem object along with their size and placement (VRAM,GTT,CPU) and
with the pid of the task that created them.
agd5f: add warning fix
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Also init the scratch reg to zero on the UVD ring.
This fixes UVD on AGP based cards.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This avoid moving the BO directly after allocating it.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add GK110 modesetting suport.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nve0: recognise nvf0 as a kepler board (GK110)
drm/nouveau: force noaccel when no PFIFO support present
drm/nvf0/disp: expose display class 2.2
Alex Deucher
Christian König
Jean-Christophe PLAGNIOL-VILLARD
Masanari Iida
Andrew Jones
Dave Airlie
Seung-Woo Kim
Inki Dae
Rob Clark
Tomi Valkeinen
Imre Deak
Lars-Peter Clausen
Sachin Kamat
Linus Torvalds
Chris Wilson
Rodrigo Vivi
Niels Ole Salscheider
Ben Skeggs
Wolfram Sang
Dave Airlie
Patrik Jakobsson
Kees Cook
Christopher Harvey
Lespiau, Damien
Chris Cummins
Jani Nikula
Ben Widawsky
Daniel Vetter
Jerome Glisse