We now:
* check for a v3 controller before setting 8-bit bus width
* offer a callback for platform code to switch to 8-bit mode, which
allows non-v3 controllers to support it
* rely on mmc->caps |= MMC_CAP_8_BIT_DATA; in platform code to specify
that the board designers have indeed brought out all the pins for
8-bit to the slot.
We were previously relying only on whether the *controller* supported
8-bit, which doesn't tell us anything about the pin configuration in
the board design.
This fixes the MMC card regression reported by Maxim Levitsky here:
http://thread.gmane.org/gmane.linux.kernel.mmc/4336
by no longer assuming that 8-bit works by default.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
While booting OMAP4 ES2.0 boards, cards on MMC1 and MMC2 controllers
are not getting detected sometimes.
During reset of command/data line, wrong pointer to base address
was passed while read operation to SYSCTL register, thus impacting
the updated reset logic.
Passing the correct base address fixes the issue.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDHC2 is newly added in C0 stepping of Langwell. Without the Moorestown
specific quirk, the default pci_probe will be called and crash the kernel.
This patch unblocks the crash problem on C0 by using the same probing
function as HC1, which limits the number of slots to one.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Only these CPUs list the bug in their errata.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes timeout problems on i.MX's sdhci as suggested by
Richard Zhu.
Tested on:
- i.MX257: not needed
- i.MX357: needed
- i.MX515: needed
More details can be found here:
http://lists.infradead.org/pipermail/linux-arm-kernel/2010-October/029748.html
Signed-off-by: Eric Bénard <eric@eukrea.com>
Tested-by: Shawn Guo <shawn.gsc@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
A little more work was needed for SDIO IRQ wakeups to be functional.
Wake-on-WLAN on the SD WiFi adapter in the XO-1.5 laptop is now working.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Improves error handling in the ushc driver.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Adding card detect callback function and card detect configuration
function for MMC1 Controller on OMAP4.
Card detect configuration function does initial configuration of the
MMC Control & PullUp-PullDown registers of Phoenix.
For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030.
Since OMAP4 doesn't use any GPIO line as used in OMAP3 for card detect,
the suspend/resume initialization which was done in omap_hsmmc_gpio_init
previously is moved to the probe thus making it generic for both OMAP3 &
OMAP4.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adjust the tmio_mmc block size check to accept 2-byte requests in 4-bit
mode if the hardware supports it.
Tested with the SDHI hardware block included in sh7724.
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Magnus Damm <damm@opensource.se>
Tested-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In some platforms (e.g. AP4EVB) the card detect pin of a slot is not
directly connected to the sh_mmcif controller, so that polling needs
to be used. To overcome the overhead induced by querying the controller
on each poll cycle, card detection can be handled in the platform code
more efficiently.
This patch exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some controllers, supported by the tmio_mmc driver do not have the card
detect pin of a slot connected, so that polling needs to be used and
card detection is handled by other means.
This patch exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (66 commits)
mmc: add new sdhci-pxa driver for Marvell SoCs
mmc: make number of mmcblk minors configurable
mmc_spi: Recover from CRC errors for r/w operation over SPI.
mmc: sdhci-pltfm: add -pltfm driver for imx35/51
mmc: sdhci-of-esdhc: factor out common stuff
mmc: sdhci_pltfm: pass more data on custom init call
mmc: sdhci: introduce get_ro private write-protect hook
mmc: sdhci-pltfm: move .h file into appropriate subdir
mmc: sdhci-pltfm: Add structure for host-specific data
mmc: fix cb710 kconfig dependency warning
mmc: cb710: remove debugging printk (info duplicated from mmc-core)
mmc: cb710: clear irq handler on init() error path
mmc: cb710: remove unnecessary msleep()
mmc: cb710: implement get_cd() callback
mmc: cb710: partially demystify clock selection
mmc: add a file to debugfs for changing host clock at runtime
mmc: sdhci: allow for eMMC 74 clock generation by controller
mmc: sdhci: highspeed: check for mmc as well as sd cards
mmc: sdhci: Add Moorestown device support
mmc: sdhci: Intel Medfield support
...
This adds the support of atmel-mci sd/mmc driver in at91sam9g45 devices and
board files. This also configures the DMA controller slave interface for
at_hdmac dmaengine driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
The SPI bus is not reliable for large data transfers on all platforms.
The current mmc_spi driver fails SD read/write commands immediately if
occasional CRC errors are reported by the SD device. This patch makes
the operation recover from CRC errors by repeating the last SD command.
The retry count is set to 5 to ensure the driver passes stress tests.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This driver adds basic support for the esdhc-core found on e.g.
imx35/51, as a platform driver.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Put everything which can be shared between the OF and platform version
of this driver into a local .h file.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Eric Bénard <eric@eukrea.com>
[cjb: fix compile error: sdhci-esdhc.c->sdhci-esdhc.h]
Signed-off-by: Chris Ball <cjb@laptop.org>
The custom init call may need more data to perform its job, so we pass
it a pointer to pdata, too. Also, always use the platform_id specific
data even if platform_data is present. Doing that, platform_data can
additionally be parsed by init() for board-specific information (via
sdhci->mmc->parent).
(Note: the old behaviour was that you could override the platform_id
specific data with your own. However, one can still do this by using the
"sdhci" id instead of "sdhci-<something>".)
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some controllers handle their write-protection differently. Introduce a
callback to be able to handle it, ensuring the same locking takes place
for it. Rename the status variable to make it more obvious why the read
from the registers needs to be inverted.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Make use of the include/linux/mmc directory.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We need to carry some information per host, e.g. the clock. Add a
structure for it and initialize it in the generic part. Also improve
the check for a parent.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix kconfig dependency warning to satisfy dependencies:
warning: (MMC_CB710 && MMC && PCI) selects CB710_CORE which has
unmet direct dependencies (MISC_DEVICES && PCI)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
Clock divider selection in partially verified, so document known facts
in code.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
Snippet of code for how adaptation layer should handle the call:
/*
* eMMC spec calls for the host to send 74 clocks to the card
* during initialization, right after voltage stabilization.
* create the clocks manually right here.
*/
void generate_init_clocks_A0(struct sdhci_host *host, u8 power_mode)
{
struct sdhci_mmc_slot *slot = sdhci_priv(host);
if (slot->power_mode == MMC_POWER_UP &&
power_mode == MMC_POWER_ON) {
/* controller specific code here */
/* slot->power_mode holds previous power setting */
}
slot->power_mode = power_mode;
}
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The SD and MMC code set highspeed using different constants.
Change the sd driver to recognize this and switch to high speed.
Validated code when testing eMMC dual data rate.
Signed-off-by: Philip Rakity <prakity@marvell.com>
[cjb: changelog + indentation fixes]
Signed-off-by: Chris Ball <cjb@laptop.org>
This adds the basic identifiers. Due to the various chip quirks it's not
enough to make MRST support very useful for earlier steppings but that can
follow.
(I'm currently trying to verify which steps actually matter outside Intel
so I can avoid unneeded stuff going upstream)
[Extracted from original development]
Signed-off-by: JiebingLi <jiebing.li@intel.com>
[Folds in fixes]
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Basic support for the Intel Medfield devices
Give them their own quirks as we will need to update this later.
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently we write it to the chip data, but if the probe handler overrides
it we ignore the new value and keep using our cached one. Fix this so that
a probe handler can adjust the slot count.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some platforms based on sdhci-pltfm need to set their own quirks.
Previously to this patch, the quirks were in drivers/mmc/host/sdhci.h.
This patch splits drivers/mmc/host/sdhci.h into two parts:
* drivers/mmc/host/sdhci.h includes the HC registers and I/O accessors.
* include/linux/mmc/sdhci.h includes the sdhci structure and quirks.
Instead of including drivers/mmc/host/sdhci.h, -pltfm drivers should
now include include/linux/mmc/sdhci.h and include/linux/sdhci-pltfm.h.
This patch avoids adding/changing the calls/flags in the
sdhci_pltfm_data structure. It has been tested on STM platforms
(e.g. STx7106, STx7108, STx5206) where the driver is configured
and used as shown in the example below:
[snip]
static int mmc_pad_resources(struct sdhci_host *sdhci)
{
if (!devm_stm_pad_claim(sdhci->mmc->parent,
&stx7108_mmc_pad_config,
dev_name(sdhci->mmc->parent)))
return -ENODEV;
return 0;
}
static struct sdhci_pltfm_data stx7108_mmc_platform_data = {
.init = mmc_pad_resources,
.quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
};
static struct platform_device stx7108_mmc_device = {
.name = "sdhci",
[snip]
Note: drivers/mmc/host/sdhci.h now also includes linux/mmc/sdhci.h,
and no modifications should be needed on other sdhci-<XXX> drivers.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes a warning when compiling the sdhci driver:
pwr may be used uninitialized in sdhci_set_power
Tested with the following compiler versions: 4.2.4 and 4.4.4
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the suspend and resume functions
in the sdhci-pltfm device driver.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
After discovering a problem in regulator reference counting I took Mark
Brown's advice to move the reference count into the MMC core by making the
regulator status a member of struct mmc_host.
I took this opportunity to also implement NULL versions of
the regulator functions so as to rid the driver code from
some ugly #ifdef CONFIG_REGULATOR clauses.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Sundar Iyer <sundar.iyer@stericsson.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Cliff Brake <cbrake@bec-systems.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When a controller requires SDHCI_QUIRK_BROKEN_CARD_DETECTION, we poll
for card insertion/removal, and that creates interrupts. There's no
need to be doing this if we have a non-removable card.
This patch requires cards to be removable before we're willing to set
MMC_CAP_NEEDS_POLL.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
[cjb: modified changelog and code indentation]
Signed-off-by: Chris Ball <cjb@laptop.org>
The EXTRA_CFLAGS assignment in mmc/Makefile was not accomplishing
anything because this flag only has effect on sources at the same level
as the makefile (i.e., per directory). Since card/, core/, and host/
rely on MMC_DEBUG, the subdir-ccflags-y variant seems to be the
appropriate choice.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In a multi-controller environment it is helpful to know which controller
has problems.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is necessary to gain the performance boost from 8-bit data
with the sdhci-stm driver.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC_CAP_MMC_HIGHSPEED allows MMC and eMMC to negotiate up to 50M
instead of the previous limit of 25M.
Signed-off-by: Zhangfei Gao <zgao6@marvell.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
While we're at it, add symbols for SDHCI_MAX_DIV_SPEC_{200,300}.
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDHC Spec 3.0: Capabilities Register bits[15-08] are Base Clock Frequency
1.0/2.0: Capabilities Register bits[13-08] are Base Clock Frequency
Signed-off-by: Zhangfei Gao <zgao6@marvell.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Michal Miroslaw <mirqus@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Zhangfei Gao <zgao6@marvell.com>
Cc: Michał Mirosław <mirqus@gmail.com>
Cc: David Vrabel <david.vrabel@csr.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The "6882a8c sdhci: Add better ADMA error reporting" commit added
sdhci_show_adma_error() which is built when DEBUG is defined. Since we
already have CONFIG_MMC_DEBUG used elsewhere in this driver, may as well
make consistent use of that config knob instead.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a driver for USB SD Host Controller devices. These devices are
Cypress Astoria chips with firmware compliant with issue 2 of CSR's USHC
specification.
[cjb: adapt to block layer deprecation of max_{hw,phys}_segs]
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We have deprecated the distinction between hardware and physical
segments in the block layer. Consolidate the two limits into one in
drivers/mmc/.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
[cjb: rebased patch against Linus]
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: <linux-mmc@vger.kernel.org>
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
[cjb: rebased patch against Linus]
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Philip Rakity
kishore kadiyala
Jacob Pan
Eric Bénard
Daniel Drake
Axel Lin
Yusuke Goda
Arnd Hannemann
Linus Torvalds
Nicolas Ferre
Zhangfei Gao
Sonic Zhang
Wolfram Sang
Randy Dunlap
Michał Mirosław
Alan Cox
Xiaochen Shen
Giuseppe Cavallaro
Linus Walleij
Jaehoon Chung
matt mooney
Zhangfei Gao
George G. Davis
David Vrabel
Martin K. Petersen
H Hartley Sweeten