[ Upstream commit e28b3abf80 ]
In order to simplify the clock-related code there is a way to convert the
current fixed clocks array into using the common bulk clocks kernel API
with dynamic set of the clock handlers and device-managed clock-resource
tracking. It's a bit tricky due to the complication coming from the
requirement to support the platforms (da850, spear13xx) with the
non-OF-based clock source, but still doable.
Before this modification there are two methods have been used to get the
clocks connected to an AHCI device: clk_get() - to get the very first
clock in the list and of_clk_get() - to get the rest of them. Basically
the platforms with non-OF-based clocks definition could specify only a
single reference clock source. The platforms with OF-hw clocks have been
luckier and could setup up to AHCI_MAX_CLKS clocks. Such semantic can be
retained with using devm_clk_bulk_get_all() to retrieve the clocks defined
via the DT firmware and devm_clk_get_optional() otherwise. In both cases
using the device-managed version of the methods will cause the automatic
resources deallocation on the AHCI device removal event. The only
complicated part in the suggested approach is the explicit allocation and
initialization of the clk_bulk_data structure instance for the non-OF
reference clocks. It's required in order to use the Bulk Clocks API for
the both denoted cases of the clocks definition.
Note aside with the clock-related code reduction and natural
simplification, there are several bonuses the suggested modification
provides. First of all the limitation of having no greater than
AHCI_MAX_CLKS clocks is now removed, since the devm_clk_bulk_get_all()
method will allocate as many reference clocks data descriptors as there
are clocks specified for the device. Secondly the clock names are
auto-detected. So the LLDD (glue) drivers can make sure that the required
clocks are specified just by checking the clock IDs in the clk_bulk_data
array. Thirdly using the handy Bulk Clocks kernel API improves the
clocks-handling code readability. And the last but not least this
modification implements a true optional clocks support to the
ahci_platform_get_resources() method. Indeed the previous clocks getting
procedure just stopped getting the clocks on any errors (aside from
non-critical -EPROBE_DEFER) in a way so the callee wasn't even informed
about abnormal loop termination. The new implementation lacks of such
problem. The ahci_platform_get_resources() will return an error code if
the corresponding clocks getting method ends execution abnormally.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Stable-dep-of: 26c8404e162b ("ata: ahci_ceva: fix error handling for Xilinx GT PHY support")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 11 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170858.370933192@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add an extra argument to ahci_platform_get_resources(), that is
for the bitmap representing the resource to get in this function.
Currently there is no resources to be defined, so all the callers set
'0' to the argument.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
'rc' is known to be 0 at this point.
If 'platform_get_resource()' or 'devm_ioremap()' fail, return -ENOMEM
instead of 0 which means success.
tj: Changed error code from -ENOMEM to -ENODEV for get_resource
failure as suggested by Sergei.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
All platforms using this driver now register the SATA refclk. Remove
the hardcoded default value from the driver and instead read the rate
of the external clock and calculate the required MPY value from it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
[nsekhar@ti.com: fix checkpatch warning about an unneeded else]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We have a use case with the da850 SATA controller where at PLL0
frequency of 456MHz (needed to properly service the LCD controller)
the chip becomes unstable and the hardreset operation is ignored the
first time 50% of times.
The sata core driver already retries to resume the link because some
controllers ignore writes to the SControl register, but just retrying
the resume operation doesn't work - we need to issue he phy/wake reset
again to make it work.
Reimplement ahci_hardreset() in the driver and poke the controller a
couple times before really giving up.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
There's an issue with the da850 SATA controller: if port multiplier
support is compiled in, but we're connecting the drive directly to
the SATA port on the board, the drive can't be detected.
To make SATA work on the da850-lcdk board: first try to softreset
with pmp - if the operation fails with -EBUSY, retry without pmp.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We're using device tree for da850-lcdk. Add the match table to allow
to probe the driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In preparation for using two clocks in the driver (the sysclk2-based
clock and the external REFCLK), check if we got the functional clock
after calling ahci_platform_get_resources(). If not, retry calling
clk_get() with con_id specified.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The owner module reference of the ahci platform's scsi_host is
initialized to libahci_platform's one, because these drivers use a
scsi_host_template defined in libahci_platform. So these drivers can
be unloaded even if the scsi device is being accessed.
This fixes it by pushing the scsi_host_template from libahci_platform
to all leaf drivers. The scsi_host_template is passed through a new
argument of ahci_platform_init_host().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-ide@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
This patch moves force_port_map and mask_port_map into the
ahci_host_priv structure. This allows to modify them into the AHCI
framework. This is needed by the new dt bindings representing ports as
the port_map mask is computed automatically.
Parameters modifying force_port_map, mask_port_map and flags have been
removed from the ahci_platform_init_host() function, and inputs in the
ahci_host_priv structure are now directly filed.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add a dynamic host_flags argument to make ahci_platform_init_host more flexible,
then remove the AHCI_HFLAGS(...) argument from some driver's ata_port_info,
and pass that in as the new argument.
Cc: Hans de Geode <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add the new ahci_da850 host driver.
Platform changes needed to make DaVinci DA850 SATA AHCI support
fully functional are in the separate "ARM: davinci: da850: update
SATA AHCI support" commit.
Please note that this driver doesn't have the superfluous clock
control code as clock is already handled by the generic AHCI
platform library code.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Serge Semin
Thomas Gleixner
Kunihiko Hayashi
Christophe JAILLET
Bartosz Golaszewski
Akinobu Mita
Wolfram Sang
Antoine Ténart
Kefeng Wang
Bartlomiej Zolnierkiewicz