The OMAP DMTimer API, omap_dm_timer_set_source(), can set the parent
of a timer node using 3 different values that use fixed parent names
for the clocks. The parent name, timer_sys_ck, is used for setting the
parent when used with the source index OMAP_TIMER_SRC_SYS_CLK. This
should point to the TIMER_SYS_CLK and not the SYSCLKIN2, so correct
the clock aliases appropriately. SYSCLKIN2 is not a mandatory clock
input.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The DT clock aliases for Timers use the legacy (non-DT) device
names and a source clock named sys_ck. OMAP5 is DT-boot only,
so correct the DT clock aliases to use the DT device names
instead. Also, the source clock name is corrected from 'sys_ck'
to 'timer_sys_ck', the name used by the OMAP dmtimer driver.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The DT clock aliases for timers using the legacy OMAP timer
device names have been cleaned up. These device names reflect
the names used in legacy boot, and are no longer applicable
as OMAP4 is DT boot only now.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Correct the McBSP2/4 ick mapping (they were 2->4 and 4->2).
Add missing mcbsp clock aliases.
Collect the McBSP clock definition in one location at the same time.
Fixes the following warning on boot:
[ 0.307739] omap_hwmod: mcbsp2: _wait_target_ready failed: -16
[ 0.307769] omap_hwmod: mcbsp2: cannot be enabled for reset (3)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
In DT boot we do not have devices named as omap-mcbsp.X.
Correct the McBSP2/4 ick mapping (they were 2->4 and 4->2).
Collect the McBSP clock definition in one location at the same time.
Fixes the following warning on boot:
[ 0.307739] omap_hwmod: mcbsp2: _wait_target_ready failed: -16
[ 0.307769] omap_hwmod: mcbsp2: cannot be enabled for reset (3)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There is a case where NULL can be a valid return value for
ti_clk_get_reg_addr, specifically the case where both the provider index
and register offsets are zero. In this case, the current error checking
against a NULL pointer will fail. Thus, change the API to return a
ERR_PTR value in an error case, and change all the users of this API to
check against IS_ERR instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
We don't really need to recalculate the effective rate of a clock when a
per-user clock is removed, if the constraints of the later aren't
limiting the requested rate.
This was causing problems with clocks that never had a rate set before,
as rate_req would be zero. Though this could be considered a bug in the
implementation of those clocks, this should be checked somewhere else.
Fixes: 1c8e600440 ("clk: Add rate constraints to clocks")
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Revert commit 039e597075 (clk: mxs: Fix invalid 32-bit access to frac
registers), because it leads to a faulty spi communication on mx28evk.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The clock passed as an argument to clk_mux_determine_rate_flags()
has the CLK_SET_RATE_PARENT flag set but it has no parent, then a
NULL pointer will tried to be dereferenced.
This shouldn't happen since setting that flag for a clock with no
parent is a bug but the core should be robust to handle that case.
Fixes: 035a61c314 ("clk: Make clk API return per-user struct clk instances")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
This time around, much of this is for at91, with the bulk of it being syscon
and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=T7R2
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
This time around, much of this is for at91, with the bulk of it being
syscon and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
cpuidle: exynos: add coupled cpuidle support for exynos4210
ARM: EXYNOS: apply S5P_CENTRAL_SEQ_OPTION fix only when necessary
soc: ti: knav_qmss_queue: change knav_range_setup_acc_irq to static
soc: ti: knav_qmss_queue: makefile tweak to build as dynamic module
pcmcia: at91_cf: depend on !ARCH_MULTIPLATFORM
soc: ti: knav_qmss_queue: export API calls for use by user driver
of/platform: teardown DMA mappings on device destruction
usb: gadget: at91_udc: Allocate udc instance
usb: gadget: at91_udc: Update DT binding documentation
usb: gadget: at91_udc: Rework for multi-platform kernel support
usb: gadget: at91_udc: Simplify probe and remove functions
usb: gadget: at91_udc: Remove non-DT handling code
usb: gadget: at91_udc: Document DT clocks and clock-names property
usb: gadget: at91_udc: Drop uclk clock
usb: gadget: at91_udc: Fix clock names
mfd: syscon: Add Atmel SMC binding doc
mfd: syscon: Add atmel-smc registers definition
mfd: syscon: Add Atmel Matrix bus DT binding documentation
mfd: syscon: Add atmel-matrix registers definition
clk: shmobile: fix sparse NULL pointer warning
...
DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new platforms
and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of DTS
contents from GPL to GPLv2+/X11 so that the same files can be reused in
other non-GPL projects more easily. There's also been changes to the
DT Makefile to make it a little less conflict-ridden and churny down
the road.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XEw1
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new
platforms and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of
DTS contents from GPL to GPLv2+/X11 so that the same files can be
reused in other non-GPL projects more easily. There's also been
changes to the DT Makefile to make it a little less conflict-ridden
and churny down the road"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (330 commits)
ARM: dts: Add PPMU node for exynos4412-trats2
ARM: dts: Add PPMU node for exynos3250-monk and exynos3250-rinato
ARM: dts: Add PPMU dt node for exynos4 and exynos4210
ARM: dts: Add PPMU dt node for exynos3250
ARM: dts: add mipi dsi device node for exynos4415
ARM: dts: add fimd device node for exynos4415
ARM: dts: Add syscon phandle to the video-phy node for Exynos4
ARM: dts: Add sound nodes for exynos4412-trats2
ARM: dts: Fix CLK_MOUT_CAMn parent clocks assignment for exynos4412-trats2
ARM: dts: Fix CLK_UART_ISP_SCLK clock assignment in exynos4x12.dtsi
ARM: dts: Add max77693 charger node for exynos4412-trats2
ARM: dts: Switch max77686 regulators to GPIO control for exynos4412-trats2
ARM: dts: Add suspend configuration for max77686 regulators for exynos4412-trats2
ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
...
New and updated SoC support. Also included are some cleanups where the
platform maintainers hadn't separated cleanups from new developent in
separate branches.
Some of the larger things worth pointing out:
- A large set of changes from Alexandre Belloni and Nicolas Ferre
preparing at91 platforms for multiplatform and cleaning up quite a
bit in the process.
- Removal of CSR's "Marco" SoC platform that never made it out to the
market. We love seeing these since it means the vendor published
support before product was out, which is exactly what we want!
New platforms this release are:
- Conexant Digicolor (CX92755 SoC)
- Hisilicon HiP01 SoC
- CSR/sirf Atlas7 SoC
- ST STiH418 SoC
- Common code changes for Nvidia Tegra132 (64-bit SoC)
We're seeing more and more platforms having a harder time labelling
changes as cleanups vs new development -- which is a good sign that
we've come quite far on the cleanup effort. So over time we might start
combining the cleanup and new-development branches more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=szd9
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Also included are some cleanups where
the platform maintainers hadn't separated cleanups from new developent
in separate branches.
Some of the larger things worth pointing out:
- A large set of changes from Alexandre Belloni and Nicolas Ferre
preparing at91 platforms for multiplatform and cleaning up quite a
bit in the process.
- Removal of CSR's "Marco" SoC platform that never made it out to the
market. We love seeing these since it means the vendor published
support before product was out, which is exactly what we want!
New platforms this release are:
- Conexant Digicolor (CX92755 SoC)
- Hisilicon HiP01 SoC
- CSR/sirf Atlas7 SoC
- ST STiH418 SoC
- Common code changes for Nvidia Tegra132 (64-bit SoC)
We're seeing more and more platforms having a harder time labelling
changes as cleanups vs new development -- which is a good sign that
we've come quite far on the cleanup effort. So over time we might
start combining the cleanup and new-development branches more"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (124 commits)
ARM: at91/trivial: unify functions and machine names
ARM: at91: remove at91_dt_initialize and machine init_early()
ARM: at91: change board files into SoC files
ARM: at91: remove at91_boot_soc
ARM: at91: move alternative initial mapping to board-dt-sama5.c
ARM: at91: merge all SOC_AT91SAM9xxx
ARM: at91: at91rm9200: set idle and restart from rm9200_dt_device_init()
ARM: digicolor: select syscon and timer
ARM: zynq: Simplify SLCR initialization
ARM: zynq: PM: Fixed simple typo.
ARM: zynq: Setup default gpio number for Xilinx Zynq
ARM: digicolor: add low level debug support
ARM: initial support for Conexant Digicolor CX92755 SoC
ARM: OMAP2+: Add dm816x hwmod support
ARM: OMAP2+: Add clock domain support for dm816x
ARM: OMAP2+: Add board-generic.c entry for ti81xx
ARM: at91: pm: remove warning to remove SOC_AT91SAM9263 usage
ARM: at91: remove unused mach/system_rev.h
ARM: at91: stop using HAVE_AT91_DBGUx
ARM: at91: fix ordering of SRAM and PM initialization
...
Clock subsystem frequently performs duplication of strings located in
read-only memory section. Replacing kstrdup by kstrdup_const allows to
avoid such operations.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) More iov_iter conversion work from Al Viro.
[ The "crypto: switch af_alg_make_sg() to iov_iter" commit was
wrong, and this pull actually adds an extra commit on top of the
branch I'm pulling to fix that up, so that the pre-merge state is
ok. - Linus ]
2) Various optimizations to the ipv4 forwarding information base trie
lookup implementation. From Alexander Duyck.
3) Remove sock_iocb altogether, from CHristoph Hellwig.
4) Allow congestion control algorithm selection via routing metrics.
From Daniel Borkmann.
5) Make ipv4 uncached route list per-cpu, from Eric Dumazet.
6) Handle rfs hash collisions more gracefully, also from Eric Dumazet.
7) Add xmit_more support to r8169, e1000, and e1000e drivers. From
Florian Westphal.
8) Transparent Ethernet Bridging support for GRO, from Jesse Gross.
9) Add BPF packet actions to packet scheduler, from Jiri Pirko.
10) Add support for uniqu flow IDs to openvswitch, from Joe Stringer.
11) New NetCP ethernet driver, from Muralidharan Karicheri and Wingman
Kwok.
12) More sanely handle out-of-window dupacks, which can result in
serious ACK storms. From Neal Cardwell.
13) Various rhashtable bug fixes and enhancements, from Herbert Xu,
Patrick McHardy, and Thomas Graf.
14) Support xmit_more in be2net, from Sathya Perla.
15) Group Policy extensions for vxlan, from Thomas Graf.
16) Remove Checksum Offload support for vxlan, from Tom Herbert.
17) Like ipv4, support lockless transmit over ipv6 UDP sockets. From
Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1494+1 commits)
crypto: fix af_alg_make_sg() conversion to iov_iter
ipv4: Namespecify TCP PMTU mechanism
i40e: Fix for stats init function call in Rx setup
tcp: don't include Fast Open option in SYN-ACK on pure SYN-data
openvswitch: Only set TUNNEL_VXLAN_OPT if VXLAN-GBP metadata is set
ipv6: Make __ipv6_select_ident static
ipv6: Fix fragment id assignment on LE arches.
bridge: Fix inability to add non-vlan fdb entry
net: Mellanox: Delete unnecessary checks before the function call "vunmap"
cxgb4: Add support in cxgb4 to get expansion rom version via ethtool
ethtool: rename reserved1 memeber in ethtool_drvinfo for expansion ROM version
net: dsa: Remove redundant phy_attach()
IB/mlx4: Reset flow support for IB kernel ULPs
IB/mlx4: Always use the correct port for mirrored multicast attachments
net/bonding: Fix potential bad memory access during bonding events
tipc: remove tipc_snprintf
tipc: nl compat add noop and remove legacy nl framework
tipc: convert legacy nl stats show to nl compat
tipc: convert legacy nl net id get to nl compat
tipc: convert legacy nl net id set to nl compat
...
of_clk_get_by_clkspec() returns a struct clk pointer but it
doesn't create a new handle for the consumers when we're using
the common clock framework. Instead it just returns whatever the
clk provider hands out. When the consumers go to call clk_put()
we get an Oops.
Unable to handle kernel paging request at virtual address 00200200
pgd = c0004000
[00200200] *pgd=00000000
Internal error: Oops: 805 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc1-00104-ga251361a-dirty #992
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
task: ee00b000 ti: ee088000 task.ti: ee088000
PC is at __clk_put+0x24/0xd0
LR is at clk_prepare_lock+0xc/0xec
pc : [<c03eef38>] lr : [<c03ec1f4>] psr: 20000153
sp : ee089de8 ip : 00000000 fp : 00000000
r10: ee02f480 r9 : 00000001 r8 : 00000000
r7 : ee031cc0 r6 : ee089e08 r5 : 00000000 r4 : ee02f480
r3 : 00100100 r2 : 00200200 r1 : 0000091e r0 : 00000001
Flags: nzCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment kernel
Control: 10c5387d Table: 4000404a DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xee088238)
Stack: (0xee089de8 to 0xee08a000)
9de0: ee7c8f14 c03f0ec8 ee089e08 00000000 c0718dc8 00000001
9e00: 00000000 c04ee0f0 ee7e0844 00000001 00000181 c04edb58 ee2bd320 00000000
9e20: 00000000 c011dc5c ee16a1e0 00000000 00000000 c0718dc8 ee16a1e0 ee2bd1e0
9e40: c0641740 ee16a1e0 00000000 ee2bd320 c0718dc8 ee1d3e10 ee1d3e10 00000000
9e60: c0769a88 00000000 c0718dc8 00000000 00000000 c02c3124 c02c310c ee1d3e10
9e80: c07b4eec 00000000 c0769a88 c02c1d0c ee1d3e10 c0769a88 ee1d3e44 00000000
9ea0: c07091dc c02c1eb8 00000000 c0769a88 c02c1e2c c02c0544 ee005478 ee1676c0
9ec0: c0769a88 ee3a4e80 c0760ce8 c02c150c c0669b90 c0769a88 c0746cd8 c0769a88
9ee0: c0746cd8 ee2bc4c0 c0778c00 c02c24e0 00000000 c0746cd8 c0746cd8 c07091f0
9f00: 00000000 c0008944 c04f405c 00000025 ee00b000 60000153 c074ab00 00000000
9f20: 00000000 c074ab90 60000153 00000000 ef7fca5d c050860c 000000b6 c0036b88
9f40: c065ecc4 c06bc728 00000006 00000006 c074ab30 ef7fca40 c0739bdc 00000006
9f60: c0718dbc c0778c00 000000b6 c0718dc8 c06ed598 c06edd64 00000006 00000006
9f80: c06ed598 c003b438 00000000 c04e64f4 00000000 00000000 00000000 00000000
9fa0: 00000000 c04e64fc 00000000 c000e838 00000000 00000000 00000000 00000000
9fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
9fe0: 00000000 00000000 00000000 00000000 00000013 00000000 c0c0c0c0 c0c0c0c0
[<c03eef38>] (__clk_put) from [<c03f0ec8>] (of_clk_set_defaults+0xe0/0x2c0)
[<c03f0ec8>] (of_clk_set_defaults) from [<c02c3124>] (platform_drv_probe+0x18/0xa4)
[<c02c3124>] (platform_drv_probe) from [<c02c1d0c>] (driver_probe_device+0x10c/0x22c)
[<c02c1d0c>] (driver_probe_device) from [<c02c1eb8>] (__driver_attach+0x8c/0x90)
[<c02c1eb8>] (__driver_attach) from [<c02c0544>] (bus_for_each_dev+0x54/0x88)
[<c02c0544>] (bus_for_each_dev) from [<c02c150c>] (bus_add_driver+0xd4/0x1d0)
[<c02c150c>] (bus_add_driver) from [<c02c24e0>] (driver_register+0x78/0xf4)
[<c02c24e0>] (driver_register) from [<c07091f0>] (fimc_md_init+0x14/0x30)
[<c07091f0>] (fimc_md_init) from [<c0008944>] (do_one_initcall+0x80/0x1d0)
[<c0008944>] (do_one_initcall) from [<c06edd64>] (kernel_init_freeable+0x108/0x1d4)
[<c06edd64>] (kernel_init_freeable) from [<c04e64fc>] (kernel_init+0x8/0xec)
[<c04e64fc>] (kernel_init) from [<c000e838>] (ret_from_fork+0x14/0x3c)
Code: ebfff4ae e5943014 e5942018 e3530000 (e5823000)
Let's create a per-user handle here so that clk_put() can
properly unlink it and free the handle. Now that we allocate a
clk structure here we need to free it if __clk_get() fails so
bury the __clk_get() call in __of_clk_get_from_provider(). We
need to handle the same problem in clk_get_sys() so export
__clk_free_clk() to clkdev.c and do the same thing, except let's
use a union to make this code #ifdef free.
This fixes the above crash, properly calls __clk_get() when
of_clk_get_from_provider() is called, and cleans up the clk
structure on the error path of clk_get_sys().
Fixes: 035a61c314 "clk: Make clk API return per-user struct clk instances"
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Alban Browaeys <prahal@yahoo.com>
Reviewed-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Anyone may call clk_round_rate() with a zero rate value, so we have to
protect against that.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
According to i.MX23 and i.MX28 reference manual [1],[2] the fractional
clock control register is 32-bit wide, but is separated in 4 parts.
So write instructions must not apply to more than 1 part at once.
The clk init for the i.MX28 violates this restriction and all the other
accesses on that register suggest that there isn't such a restriction.
This patch restricts the access to this register to byte instructions and
extends the comment in the init functions.
Btw the imx23 init now uses a R-M-W sequence just like imx28 init
to avoid any clock glitches.
The changes has been tested with a i.MX23 and a i.MX28 board.
[1] - http://cache.freescale.com/files/dsp/doc/ref_manual/IMX23RM.pdf
[2] - http://cache.freescale.com/files/dsp/doc/ref_manual/MCIMX28RM.pdf
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The 'ARM: OMAP3: legacy clock data move under clk driver' patch series
causes build errors when CONFIG_OMAP3 is not set:
drivers/clk/ti/dpll.c: In function 'ti_clk_register_dpll':
drivers/clk/ti/dpll.c:199:31: error: 'omap3_dpll_ck_ops' undeclared (first use in this function)
const struct clk_ops *ops = &omap3_dpll_ck_ops;
^
drivers/clk/ti/dpll.c:199:31: note: each undeclared identifier is reported only once for each function it appears in
drivers/clk/ti/dpll.c:259:10: error: 'omap3_dpll_per_ck_ops' undeclared (first use in this function)
ops = &omap3_dpll_per_ck_ops;
^
drivers/built-in.o: In function `ti_clk_register_gate':
drivers/clk/ti/gate.c:179: undefined reference to `clkhwops_omap3430es2_dss_usbhost_wait'
drivers/clk/ti/gate.c:179: undefined reference to `clkhwops_am35xx_ipss_module_wait'
-in.o: In function `ti_clk_register_interface':
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_omap3430es2_iclk_hsotgusb_wait'
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_omap3430es2_iclk_dss_usbhost_wait'
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_omap3430es2_iclk_ssi_wait'
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_am35xx_ipss_wait'
drivers/built-in.o: In function `ti_clk_register_composite':
:(.text+0x3da768): undefined reference to `ti_clk_build_component_gate'
In order to fix that problem, this patch makes the omap3 legacy code
compiled only when both CONFIG_OMAP3 and CONFIG_ATAGS are set.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
and addition of clock definitions for DVFS on Exynos4.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rFdT
-----END PGP SIGNATURE-----
Merge tag 'v3.20-exynos-clk' of git://linuxtv.org/snawrocki/samsung into clk-next
Exynos 3250, 4415 drivers cleanup by using common code
and addition of clock definitions for DVFS on Exynos4.
So it can be used from modules such as clk-test.ko.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Adds a way for clock consumers to set maximum and minimum rates. This
can be used for thermal drivers to set minimum rates, or by misc.
drivers to set maximum rates to assure a minimum performance level.
Changes the signature of the determine_rate callback by adding the
parameters min_rate and max_rate.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[sboyd@codeaurora.org: set req_rate in __clk_init]
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: min/max rate for sun6i_ahb1_clk_determine_rate
migrated clk-private.h changes to clk.c]
Private clock framework data structures should be private, surprisingly.
Now that all platforms and drivers have been updated to remove static
initializations of struct clk and struct clk_core objects and all
references to clk-private.h have been removed we can move the
definitions of these structures into drivers/clk/clk.c and delete the
header.
Additionally the ugly DEFINE_CLK macros have been removed. Those were
used for static definitions of struct clk objects. That practice is no
longer allowed.
Finally __clk_init is staticized as it is no longer declared in any
header.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Moves clock state to struct clk_core, but takes care to change as little API as
possible.
struct clk_hw still has a pointer to a struct clk, which is the
implementation's per-user clk instance, for backwards compatibility.
The struct clk that clk_get_parent() returns isn't owned by the caller, but by
the clock implementation, so the former shouldn't call clk_put() on it.
Because some boards in mach-omap2 still register clocks statically, their clock
registration had to be updated to take into account that the clock information
is stored in struct clk_core now.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: adapted clk_has_parent to struct clk_core
applied OMAP3+ DPLL fix from Tero & Tony]
PLLD is the only parent for DSIA & DSIB on Tegra124 and
Tegra132. Besides, BIT 30 in PLLD_MISC register controls
the output of DSI clock.
So this patch removes "dsia_mux" & "dsib_mux", and create
a new clock "plld_dsi" to represent the DSI clock enable
control.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Mark Zhang <markz@nvidia.com>
Tegra132 CAR supports almost the same clocks as Tegra124 CAR. This
patch mostly deals with the small differences.
Since Tegra132 contains many of the same PLL clock sources used on
Tegra114 and Tegra124, enable them in drivers/clk/tegra/clk-pll.c when
the kernel is configured to include Tegra132 support.
This patch is based on several patches from others:
1. a patch from Peter De Schrijver:
http://lkml.iu.edu/hypermail/linux/kernel/1407.1/06094.html
2. a patch from Bill Huang ("clk: tegra: enable cclk_g at boot on
Tegra132"), and
3. a patch from Allen Martin ("clk: Enable tegra clock driver for
tegra132").
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Allen Martin <amartin@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Bill Huang <bilhuang@nvidia.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
tegra_clocks_apply_init_table() needs to be called after the udelay
loop has been calibrated (see commit
441f199a37 ("clk: tegra: defer
application of init table") for why that is). On existing Tegra SoCs
this was done by calling tegra_clocks_apply_init_table() from
tegra_dt_init(). To make this also work on ARM64, we need to change
this into an initcall. tegra_dt_init() is called from
customize_machine which is an arch_initcall. Therefore this should
also work on existing 32bit Tegra SoCs.
Tested on Tegra20 (ventana), Tegra30 (beaverboard), Tegra124 (jetson TK1) and
Tegra132.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
[paul@pwsan.com: tweaked the commit message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
As previously the names of the present clock and its parent were swapped.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Set the parent of the dsi lp clocks to pll_p and the rate
to 68MHz. The default parent is clk_m and rate is 12MHz, this
is too slow to receive data from the peripheral.
Per NVidia HW engineers, the optimal rate is 70MHz, but 68MHz
will suffice.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Since the SDMMC controller registers are accessed via the APB,
the APB must be flushed before gating the SDMMC clocks to prevent
register accesses to the SDMMC controllers after their clocks are
gated.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Introduces omap3 legacy clock data under clock driver. The clock data
is also in new format, which makes it possible to get rid of the
clk-private.h header. This patch also introduces SoC specific init
functions that shall be called from the low level init.
The data format used in this file has two possible evolution paths;
it can either be removed completely once no longer needed, or it will
be possible to retain the format and modify the TI clock driver to be
a loadable module at some point. The actual path to be followed
will be decided later.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialized slightly differently compared to
DT clocks, thus add support for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialized slightly differently compared to
DT clocks, thus add support for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialized slightly differently compared to
DT clocks, thus add support for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialized slightly differently compared to
DT clocks, thus add support for this. The interface clock descriptor
itself is overloading the gate clock descriptor, thus it needs to
be called from the gate setup.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialialized slightly differently compared to
DT clocks, thus add support for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialized slightly differently compared to
DT clocks, thus add support for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data for OMAP3 is being moved under clock driver, thus
base support for this is needed. This patch adds basic definitions for
clock init descriptors and core infrastructure for initialization,
which will be called from the OMAP3 clock init.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
When a power domain is powered off on Exynos5420 SoC, the input clocks of
the devices attached to this power domain are re-parented to oscclk and
restored to the original parent after powering on the power domain.
So a reference to the input and parent clocks for the devices attached to
a power domain are needed to be able to do the re-parenting. The DISP1 pd
includes modules which uses the following clocks:
ACLK_200_DISP1 (MIXER and HDMILINK)
ACLK_300_DISP1 (FIMD1)
ACLK_400_DISP1 (Internal Buses)
Each of these clocks are generated as the output of a clock mux so add an
ID for all of these clock muxes and their parents to be referenced in the
DISP1 power domain device node.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
As it has never been used.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
As clk_unprepare_unused_subtree and clk_disable_unused_subtree are
always called with a valid struct clk.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Currently a mix of clk-qoriq/qoriq-clk and no prefix is used
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
drivers/clk/clk-qoriq.c:59:22: warning: symbol 'cmux_ops' was not declared. Should it be static?
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
WARNING:OOM_MESSAGE: Possible unnecessary 'out of memory' message
+ if (!parent_names) {
+ pr_err("%s: could not allocate parent_names\n", __func__);
WARNING:OOM_MESSAGE: Possible unnecessary 'out of memory' message
+ if (!cmux_clk) {
+ pr_err("%s: could not allocate cmux_clk\n", __func__);
WARNING:OOM_MESSAGE: Possible unnecessary 'out of memory' message
+ if (!subclks) {
+ pr_err("%s: could not allocate subclks\n", __func__);
WARNING:OOM_MESSAGE: Possible unnecessary 'out of memory' message
+ if (!onecell_data) {
+ pr_err("%s: could not allocate onecell_data\n", __func__);
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Suman Anna
Peter Ujfalusi
Tero Kristo
Linus Torvalds
Tomeu Vizoso
Stefan Wahren
Emil Medve
Javier Martinez Canillas
Andrzej Hajda
Stephen Boyd
Geert Uytterhoeven
Arnd Bergmann
Michael Turquette
Mark Zhang
Paul Walmsley
Peter De Schrijver
Sean Paul
Andrew Bresticker