[ Upstream commit c3df0e29fb7788c4b3ddf37d5ed87dda2b822943 ]
inv_mpu6050_sensor_show() can return -EINVAL or IIO_VAL_INT. Return the
true value rather than only return IIO_VAL_INT.
Fixes: d509844714 ("iio: imu: mpu6050: add calibration offset support")
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20231030020218.65728-1-suhui@nfschina.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bbaae0c79e upstream.
Timestamp reset is not done in the correct place. It must be done
before enabling buffer. The reason is that interrupt timestamping
is always happening when the chip is on, even if the
corresponding sensor is off. When the sensor restarts, timestamp
is wrong if you don't do a reset first.
Fixes: ec74ae9fd3 ("iio: imu: inv_icm42600: add accurate timestamping")
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230509152202.245444-1-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2acd031347 upstream.
+/-1200uT is a MAGN sensor full measurement range. Magnetometer scale
is the magnetic sensitivity parameter. It is referenced as 0.1uT
according to datasheet and magnetometer channel unit is Gauss in
sysfs-bus-iio documentation. Gauss and uTesla unit conversion
relationship as follows: 0.1uT = 0.001Gs.
Set magnetometer scale and available magnetometer scale as fixed 0.001Gs.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-5-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff5e2cd92f upstream.
FXOS8700_CTRL_ODR_MIN is not used but value is probably wrong.
Remove it for a good readability.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-4-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eb6d8f8705 upstream.
The absence of correct offset leads a failed initialization ODR mode
assignment.
Select MAX ODR mode as the initialization ODR mode by field mask and
FIELD_PREP.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-3-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 78ad6864e9 upstream.
The absence of a correct offset leads an incorrect ODR mode
readback after use a hexadecimal number to mark the value from
FXOS8700_CTRL_REG1.
Get ODR mode by field mask and FIELD_GET clearly and conveniently.
And attach other additional fix for keeping the original code logic
and a good readability.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20230118074227.1665098-2-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c68b44bc7d upstream.
Because ACCEL and MAGN channels data register base address is
swapped the accelerometer and magnetometer channels readback is
swapped.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-3-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 429e1e8ec6 upstream.
FXOS8700 is an IMU sensor with ACCEL sensor and MAGN sensor.
Sensor type is indexed by corresponding channel type in a switch.
IIO_ANGL_VEL channel type mapped to MAGN sensor has caused confusion.
Fix the mapping label of "IIO_MAGN" channel type instead of
"IIO_ANGL_VEL" channel type to MAGN sensor.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-2-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a53f945879 upstream.
ACCEL output data registers contain the X-axis, Y-axis, and Z-axis
14-bit left-justified sample data and MAGN output data registers
contain the X-axis, Y-axis, and Z-axis 16-bit sample data. The ACCEL
raw register output data should be divided by 4 before sent to
userspace.
Apply a 2 bits signed right shift to the raw data from ACCEL output
data register but keep that from MAGN sensor as the origin.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-5-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37a94d86d7 upstream.
The length of ACCEL and MAGN 3-axis channels output data is 6 byte
individually. However block only read 3 bytes data into buffer from
ACCEL or MAGN output data registers every time. It causes an incomplete
ACCEL and MAGN channels readback.
Set correct value count for regmap_bulk_read to get 6 bytes ACCEL and
MAGN channels readback.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-4-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d61c18205 upstream.
When device is in active mode, it fails to set an ACCEL full-scale
range(2g/4g/8g) in FXOS8700_XYZ_DATA_CFG. This is not align with the
datasheet, but it is a fxos8700 chip behavior.
Keep the device in standby mode before setting ACCEL full-scale range
into FXOS8700_XYZ_DATA_CFG in chip initialization phase and setting
scale phase.
Fixes: 84e5ddd5c4 ("iio: imu: Add support for the FXOS8700 IMU")
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Link: https://lore.kernel.org/r/20221208071911.2405922-6-carlos.song@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 99c05e4283 ]
Add '__adis_enable_irq()' implementation which is the unlocked
version of 'adis_enable_irq()'.
Call '__adis_enable_irq()' instead of 'adis_enable_irq()' from
'__adis_intial_startup()' to keep the expected unlocked functionality.
This fix is needed to remove a deadlock for all devices which are
using 'adis_initial_startup()'. The deadlock occurs because the
same mutex is acquired twice, without releasing it.
The mutex is acquired once inside 'adis_initial_startup()', before
calling '__adis_initial_startup()', and once inside
'adis_enable_irq()', which is called by '__adis_initial_startup()'.
The deadlock is removed by calling '__adis_enable_irq()', instead of
'adis_enable_irq()' from within '__adis_initial_startup()'.
Fixes: b600bd7eb3 ("iio: adis: do not disabe IRQs in 'adis_init()'")
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20221122082757.449452-2-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c9304d6af ]
In order to avoid unneessary pollution of the global symbol namespace
move the common/library functions into a specific namespace and import
that into the various specific device drivers that use them.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Song Bao Hua (Barry Song) <song.bao.hua@hisilicon.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220130205701.334592-9-jic23@kernel.org
Stable-dep-of: 99c05e4283 ("iio: adis: add '__adis_enable_irq()' implementation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31fa357ac8 ]
Some devices can't mask/unmask the data ready pin and in those cases
each driver was just calling '{dis}enable_irq()' to control the trigger
state. This change, moves that handling into the library by introducing
a new boolean in the data structure that tells the library that the
device cannot unmask the pin.
On top of controlling the trigger state, we can also use this flag to
automatically request the IRQ with 'IRQF_NO_AUTOEN' in case it is set.
So far, all users of the library want to start operation with IRQs/DRDY
pin disabled so it should be fairly safe to do this inside the library.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210903141423.517028-3-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 99c05e4283 ("iio: adis: add '__adis_enable_irq()' implementation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d722f1e06f ]
strcpy() performs no bounds checking on the destination buffer. This
could result in linear overflows beyond the end of the buffer, leading
to all kinds of misbehaviors. So, remove all the uses and add
devm_kstrdup() or devm_kasprintf() instead.
Also, modify the "for" loop conditions to clarify the access to the
st->orientation.rotation buffer.
This patch is an effort to clean up the proliferation of str*()
functions in the kernel and a previous step in the path to remove
the strcpy function from the kernel entirely [1].
[1] https://github.com/KSPP/linux/issues/88
Signed-off-by: Len Baker <len.baker@gmx.com>
Link: https://lore.kernel.org/r/20210815174204.126593-1-len.baker@gmx.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 106b391e1b upstream.
The 0 value used for INV_CHIP_ICM42600 was not working since the
match in i2c/spi was checking against NULL value.
To keep this check, add a first INV_CHIP_INVALID 0 value as safe
guard.
Fixes: 31c24c1e93 ("iio: imu: inv_icm42600: add core of new inv_icm42600 driver")
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20220609102301.4794-1-jmaneyrol@invensense.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5d6ba09b1 upstream.
This register write to REG_INTF_CONFIG6 enables a spike filter that
is impacting the line and can prevent the I2C ACK to be seen by the
controller. So we don't test the return value.
Fixes: 7297ef1e26 ("iio: imu: inv_icm42600: add I2C driver")
Signed-off-by: Fawzi Khaber <fawzi.khaber@tdk.com>
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20220411111533.5826-1-jmaneyrol@invensense.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 632fe0bb8c upstream.
The pm_runtime_enable will increase power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable(). In the PM Runtime docs:
Drivers in ->remove() callback should undo the runtime PM changes done
in ->probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc.
We should do this in error handling.
Fix this problem for the following drivers: bmc150, bmg160, kmx61,
kxcj-1013, mma9551, mma9553.
Fixes: 7d0ead5c3f ("iio: Reconcile operation order between iio_register/unregister and pm functions")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220106112309.16879-1-linmq006@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea85bf9064 upstream.
We need to wait for sensor settling time (~ 3/ODR) before reading data
in st_lsm6dsx_read_oneshot routine in order to avoid corrupted samples.
Fixes: 290a6ce11d ("iio: imu: add support to lsm6dsx driver")
Reported-by: Mario Tesi <mario.tesi@st.com>
Tested-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/b41ebda5535895298716c76d939f9f165fcd2d13.1644098120.git.lorenzo@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b0e85f95e3 upstream.
The trigger handler defined in the driver assumes that burst mode is
being used. Hence, for devices that do not support it, we have to use
the adis library default trigger implementation.
Tested-by: Julia Pineda <julia.pineda@analog.com>
Fixes: 941f130881 ("iio: adis16480: support burst read function")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220114132608.241-1-nuno.sa@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 94be878c88 ]
The length of hw->settings->odr_table is 2 and ref_sensor->id is an enum
variable whose value is between 0 and 5.
However, the value ST_LSM6DSX_ID_MAX (i.e. 5) is not caught properly in
switch (sensor->id) {
If ref_sensor->id is ST_LSM6DSX_ID_MAX, an array overflow will ocurrs in
function st_lsm6dsx_check_odr():
odr_table = &sensor->hw->settings->odr_table[sensor->id];
and in function st_lsm6dsx_set_odr():
reg = &hw->settings->odr_table[ref_sensor->id].reg;
To avoid this array overflow, handle ST_LSM6DSX_ID_GYRO explicitly and
return -EINVAL for the default case.
The enum value ST_LSM6DSX_ID_MAX is only present as an easy way to check
the limit and as such is never used, however this is not locally obvious.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Teng Qi <starmiku1207184332@gmail.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/20211011114003.976221-1-starmiku1207184332@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b600bd7eb3 ]
With commit ecb010d441 ("iio: imu: adis: Refactor adis_initial_startup")
we are doing a HW or SW reset to the device which means that we'll get
the default state of the data ready pin (which is enabled). Hence there's
no point in disabling the IRQ in the init function. Moreover, this
function is intended to initialize internal data structures and not
really do anything on the device.
As a result of this, some devices were left with the data ready pin enabled
after probe which was not the desired behavior. Thus, we move the call to
'adis_enable_irq()' to the initial startup function where it makes more
sense for it to be.
Note that for devices that cannot mask/unmask the pin, it makes no sense
to call the function at this point since the IRQ should not have been
yet requested. This will be improved in a follow up change.
Fixes: ecb010d441 ("iio: imu: adis: Refactor adis_initial_startup")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210903141423.517028-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Not all devices supported by this driver support being put to sleep
mode. For those devices, when calling 'adis16480_stop_device()' on the
unbind path, we where actually writing in the SYNC_SCALE register.
Fixes: 80cbc848c4 ("iio: imu: adis16480: Add support for ADIS16490")
Fixes: 82e7a1b250 ("iio: imu: adis16480: Add support for ADIS1649x family of devices")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210903141423.517028-6-nuno.sa@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With commit 39c024b51b
("iio: adis16475: improve sync scale mode handling"), two deadlocks were
introduced:
1) The call to 'adis_write_reg_16()' was not changed to it's unlocked
version.
2) The lock was not being released on the success path of the function.
This change fixes both these issues.
Fixes: 39c024b51b ("iio: adis16475: improve sync scale mode handling")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210920090047.74903-1-nuno.sa@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The st-sensors drivers have changed in structure over time, and includes
have not always kept up with this. Let's bring them back to nearer
the ideal.
Identified with the include-what-you-use tool and careful checking of
its suggestions.
Note I haven't been particularly aggressive here, so this is just the
cases where the include obviously isn't needed rather than the more
subtle corners.
Note I took the opportunity to add mod_devicetable.h as I generally
prefer to see that when acpi or of match tables are present.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Denis Ciocca <denis.ciocca@st.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210608175149.4019289-1-jic23@kernel.org
Add startup time for each chip familly. This allows a better behaviour of
the gyro and the accel. The gyro has now the time to stabilise itself
thus making initial data discarding for gyro irrelevant.
Signed-off-by: Baptiste Mansuy <bmansuy@invensense.com>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Link: https://lore.kernel.org/r/20210621085731.9212-1-bmansuy@invensense.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Set reset pin direction to output as the reset pin needs to be an active
low output pin.
Co-developed-by: Hannu Hartikainen <hannu@hrtk.in>
Signed-off-by: Hannu Hartikainen <hannu@hrtk.in>
Signed-off-by: Antti Keränen <detegr@rbx.email>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Fixes: ecb010d441 ("iio: imu: adis: Refactor adis_initial_startup")
Link: https://lore.kernel.org/r/20210708095425.13295-1-detegr@rbx.email
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove an unblanced pm_runtime_put_sync_suspend() call
in inv_pu_pm_disable(). Not this call is not a bug, because the runtime
pm core will not allow the reference counter to go negative. It is
however confusing and serves no purpose.
pm_runtime_resume_and_get() case found using coccicheck script under
review at:
https://lore.kernel.org/lkml/20210427141946.2478411-1-Julia.Lawall@inria.fr/
pm_runtime_resume_and_get() returns <= 0 only so simplify related checks
to bring this more inline with nearby calls.
This is a prequel to taking a closer look at the runtime pm in IIO drivers
in general.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/20210516162103.1332291-2-jic23@kernel.org
These were usually used before the conversion to devm_ functions, so that
the remove hook would be able to retrieve the pointer and do cleanups on
remove.
When the conversion happened, they should have been removed, but were
omitted.
Some drivers were copied from drivers that fit the criteria described
above. In any case, in order to prevent more drivers from being used as
example (and have spi_set_drvdata() needlessly set), this change removes it
from the IIO IMU group.
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210513122512.93187-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since:
commit cbacb5ab0a ("docs: printk-formats: Stop encouraging use of
unnecessary %h[xudi] and %hh[xudi]")
use of these format strings has been discouraged.
Use the 0x02x form as the length specifier when used with # includes
the 0x prefix and is very unlikely to be what was intended by the author.
Part of a series removing all uses from IIO in the interestings of
avoiding providing bad examples for people to copy.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210603180612.3635250-4-jic23@kernel.org
0-day recently added the include-what-you-use header checker and
it gave a warning on an adis patch. As such I decided to
run it on all the adis drivers and see if it made sensible suggestions.
Note this doesn't represent a complete list of what it suggested changing
as I filtered out a few on the basis they are standard headers used to
effectively include a bunch of other headers.
Could split this into a patch per driver if people prefer.
Note to anyone else trying this tool is that it is somewhat
of a loose cannon so you will be wanting to carefully check any
suggestions before proposing patches!
I thought about also reorganising the headers whilst here, but
that would make this patch harder to read, or lead to another rather
noisy patch across most of the files.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210603193616.3708447-1-jic23@kernel.org
All of the users of iio_read_mount_matrix() are using the very same
property name. Moreover, the property name is hard coded in the API
documentation.
Make this clear and avoid duplication now and in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210518112546.44592-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some supported devices support burst read function. This provides a method
for reading a batch of data (status, temperature, gyroscopes,
accelerometers, time stamp/data counter, and CRC code), which does not
require a stall time between each 16-bit segment and only requires one
command on the DIN line to initiate. Devices supporting this mode
are:
* adis16495-1
* adis16495-2
* adis16495-3
* adis16497-1
* adis16497-2
* adis16497-3
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210422103735.136367-1-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
No point in calling pm_runtime_put_noidle() that isn't balancing a get.
Note no actual impact because the runtime pm core protects against
a negative reference counter.
For the pm_runtime_resume_and_get() main interest is in clearing
out this old pattern to avoid it getting coppied into new submissions.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/20210509113354.660190-10-jic23@kernel.org
Fix wrongly stated 13 Hz ODR for accelerometers, the correct ODR is 12.5 Hz
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We can utilize separate drivers for accelerometer and magnetometer,
so here is the glue driver to enable LSM9DS0 IMU support.
The idea was suggested by Crestez Dan Leonard in [1]. The proposed change
was sent as RFC due to race condition concerns, which are indeed possible.
In order to amend the initial change, I went further by providing a specific
multi-instantiate probe driver that reuses existing accelerometer and
magnetometer.
[1]: https://lore.kernel.org/patchwork/patch/670353/
Suggested-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Cc: mr.lahorde@laposte.net
Cc: Matija Podravec <matija_podravec@fastmail.fm>
Cc: Sergey Borishchenko <borischenko.sergey@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210414195454.84183-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Continuing from Alexandru Ardelean's introduction of the split between
driver modifiable fields and those that should only be set by the core.
This could have been done in two steps to make the actual move after
introducing iio_device_id() but there seemed limited point to that
given how mechanical the majority of the patch is.
Includes fixup from Alex for missing mxs-lradc-adc conversion.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210426174911.397061-2-jic23@kernel.org
With commit 3ba10e37371d ("iio: adis: add burst_max_speed_hz variable"), we
just need to define 'burst_max_speed_hz' and the adis core will take
care of setting up the spi transfers for burst mode. Hence, we fix
a potential race with the spi core where we could be left witn an
invalid 'max_speed_hz'.
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Fixes: 5eda3550a3 ("staging:iio:adis16400: Preallocate transfer message")
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210427085454.30616-7-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
With commit 3ba10e37371d ("iio: adis: add burst_max_speed_hz variable"), we
just need to define 'burst_max_speed_hz' and the adis core will take
care of setting up the spi transfers for burst mode. Hence, we fix
a potential race with the spi core where we could be left with an
invalid 'max_speed_hz'.
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Fixes: fff7352bf7 ("iio: imu: Add support for adis16475")
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210427085454.30616-6-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Typically, in burst mode, the device cannot operate at it's full spi
speed. Hence, the spi transfers for burst mode have to take this into
account. With this change we avoid a potential race with the spi core as
drivers were 'hacking' the device 'max_speed_hz' directly in the
trigger handler.
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210427085454.30616-5-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There's no point in pushing data to IIO buffers in case 'spi_sync()'
fails.
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210427085454.30616-4-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It makes more sense to update the device page as soon as we we
successfully changed it. Moreover, a follow up patch will handle
'spi_sync' error path which would leave 'current_page' in a inconsistent
state.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210427085454.30616-3-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On an IRQ handler we should not return normal error codes as 'irqreturn_t'
is expected.
This is done by jumping to the 'check_burst32' label where we return
'IRQ_HANDLED'. Note that it is fine to do the burst32 check in this
error path. If we have proper settings to apply burst32, we might just
do the setup now so that the next sample already uses it.
Fixes: fff7352bf7 ("iio: imu: Add support for adis16475")
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210427085454.30616-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On the trigger handler, we might need to change the device page. Hence,
we should check the return value from 'spi_write()' and act accordingly.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210422101911.135630-5-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On an IRQ handler we should not return normal error codes as 'irqreturn_t'
is expected.
Not necessary to apply to stable as the original check cannot fail and
as such the bug cannot actually occur.
Fixes: 5eda3550a3 ("staging:iio:adis16400: Preallocate transfer message")
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210422101911.135630-3-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On an IRQ handler we should not return normal error codes as 'irqreturn_t'
is expected.
Not necessarily stable material as the old check cannot fail, so it's a bug
we can not hit.
Fixes: ccd2b52f4a ("staging:iio: Add common ADIS library")
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20210422101911.135630-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Su Hui
Jean-Baptiste Maneyrol
Arnd Bergmann
Carlos Song
Ramona Bolboaca
Jonathan Cameron
Nuno Sá
Len Baker
Tong Zhang
Fawzi Khaber
Miaoqian Lin
Lorenzo Bianconi
Teng Qi
Greg Kroah-Hartman
Baptiste Mansuy
Antti Keränen
Alexandru Ardelean
Andy Shevchenko
Sean Nyekjaer